Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rolling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications

Oak Ridge National Laboratory is developing advanced low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys for accident tolerant fuel (ATF) cladding. This report presents the characterization of two new ODS FeCrAl tubes by using powder commercially mechanically alloyed by Zoz GmbH, which underwent high-precision tube rolling with two different annealing schedules. This work shows that the ODS FeCrAl tube without recrystallization exhibits consistent mechanical behavior in comparison with a previously produced tube. The second tube, which underwent a full recrystallization step before the final tube rolling step, showed some circumferential cracking and exhibited limited ductility in the axial tube tensile tests. Based on current and prior work on the ODS FeCrAl alloy system, this report compares the current state of the scientific literature on the alloy class with that of wrought FeCrAl without oxide additions. Then, this report makes recommendations for future research directions that should be undertaken to increase the technology readiness level for ODS FeCrAl as a viable ATF candidate material. This report has been submitted as fulfillment of milestone M3FT-20OR020202064 titled, “STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications” for the US Department of Energy Office of Nuclear Energy’s Advanced Fuel Campaign of the Fuel Cycle R&D program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Highly Ordered Hierarchical Anodes for Extreme Fast Charging Batteries (Final Report)

The goal of this project is to enable extreme fast charging (XFC) of Li-ion batteries, which was accomplished through a combination of 1) rational design and manufacturing of hierarchically structured anode architectures; 2) blending graphite/hard carbon into a bulk hybrid anode; 3) engineering artificial solid-electrolyte interphase (SEI) coatings with reduced interphase impedance; 4) computational modeling of coupled transport, kinetic, and electrochemical phenomena; and 5) improved fundamental understanding of lithium plating through operando analysis. This work integrated structural, compositional, and surface modification of graphite anodes, multi-physics modeling of ion transport, electrochemical activity, and heat transfer, advanced strategies to detect Li plating, and semi-automated roll-to-roll cell assembly. The unique facilities at the University of Michigan (UM) and Sandia National Laboratories (SNL) were leveraged to manufacture, prototype, and characterize commercially relevant >2Ah and >180 Wh/kg cells with a target of <20% capacity fade over 500 XFC cycles.

25 ENERGY STORAGE↗
DOE OSTI2020

Nanometal-Interconnected Carbon Conductors (NICCS) for Advanced Electric Machines (RIT Final Technical Report)

Recent advancements in carbon nanotube (CNT) research have enabled lightweight, conductive wires as a transformative technology. Metal-carbon nanotube (CNT) hybrid conductors aim to combine the high conductivity of traditional metals with the low mass and temperature coefficient of resistance (TCR) of carbon nanotubes. The high conductivity of copper makes it a promising candidate to combine with CNTs in a hybrid structure, but there is limited physical and electrical interaction between copper and CNTs. The use of an interfacial layer offers one method of improving the interconnection of a Cu-CNT hybrid conductor. Over the course of this grant, a joule heating-driven chemical vapor deposition (CVD) technique was developed to deposit nanometal seeds throughout a porous, low-density (0.12 g/cm 3 , ~10 tex or mg/m) CNT roving template. Modification of the applied current to the CNT roving allows for the tuning of depositions towards either hot-spot site-specificity or overall uniformity. The effects of temperature, pressure, precursor mass, and the interval of applied current were investigated, demonstrating nanometal depositions ranging from less than 5 % w/w to over 85 % w/w. The versatility of CVD allows for a wide variety of metals to be deposited including copper, titanium, nickel, silver, tungsten, palladium, platinum, ruthenium, rhodium, and iridium. One preferred demonstration involved using platinum depositions to improve the electrical properties of metal-seeded CNTs across all mass loadings studied. Moreover, when the metal-seeded CNT wires were electroplated with copper, densified, and annealed under hydrogen/argon; the result was a Cu-CNT hybrid conductor with the highest conductivities reported to date. The good interconnection of the metal and CNT portions results in a stable conductor. An electrical conductivity of 16-20 MS/m was achieved for multiple Cu-CNT hybrid conductors at 150 °C, which exceeds the program goal for conductivity of greater than 15 MS/m for a 1 m long CNT wire. Overall, the research outcomes from the project showed improvements in CNT wire fabrication from roll-to-roll CVD grown carbon nanotube wires using nanometal interconnects to bridge CNT-to-CNT junctions, thus mitigating network contact resistances. Advanced nanometal interconnected carbon conductors (NICCs) were developed as a means to achieve novel light-weight wiring appropriate for applications that require the conductivity of metallic (i.e., Cu, Al, etc.) wires at elevated temperatures. High conductivity, low TCR electrical conductors such as the nanometal interconnected Cu-CNT hybrids have numerous future applications towards high efficiency motors, generators, and transformers. Specifically, the advanced wires have the ability to operate at lower resistance during conditions for standard electric motors at 150 °C, which would improve the electrical efficiency while lowering energy needs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

LightMAT - Continuous fiber malleable thermoset composites with sub-1-minute dwell times; validation of impact performance and evaluation of the efficacy of the compression forming process (CRADA 409 Final Report)

In spite of carbon fiber composite materials’ significant impact on light-weighting, performance, and efficiency in the aerospace industry, adoption of these materials has been slow in high-volume industries such as automotive. Two major barriers to adoption are cost and cycle-time. Current approaches to thermoset composite part production are dependent on in-mold curing of thermosets which are not optimal for high volume, high throughput production due to limitations and inefficiencies associated with the in-mold cure itself. In addition, ancillary activities, such as transport and storage of shelf-life-limited uncured, or B-staged prepreg materials typically necessitate refrigerated transport and storage which significantly impacts the economic and energy costs associated with manufacturing. Furthermore, limited out-life means that trimmings cannot typically be used as they partially cure during initial production leading to high scrap rates (+20% is common). Finally, the need to cure in-mold drives cycle times to multiple minutes in the best cases, and 10’s of minutes to hours in most cases. Mallinda is developing polyimine malleable thermoset prepreg composite materials which have excellent mechanical properties (100 GPa tensile modulus, 2 GPA tensile strength, 2.4% elongation at break) and high operating temperatures (Tg>200°C). At scale, polyimine resins are commensurate in price with commodity epoxy resins. What distinguishes malleable thermoset prepreg from traditional thermoset prepreg materials, is that they are fully cured during Mallinda’s roll-to-roll production of prepreg laminate. This results in 5 key value-differentiating benefits. First, it simplifies manufacturing logistics by enabling ambient transportation and storage, and by significantly extending out-life and shelf-life almost indefinitely. Second, elimination of autoclave curing reduces the economic and energy costs to the customer. Third, scrap rates can be reduced as malleable thermoset prepreg materials are directly reusable. Fourth, the manufacturing consolidation step can be roughly 10x faster than traditional thermosets, because the resin is already cured. Parts can be made via compression forming by the application of heat and pressure to quickly vitrify and consolidate a multilayer part – easily leading to sub 3-minute cycle times (at lab scale we have demonstrated a 20 second dwell time, with room for further optimization). Finally, the closed-loop cradle-to-cradle solution-based recyclability of malleable thermoset composites can also contribute significantly to the future of sustainable lightweight materials. The focus of this project was the development, optimization and validation of malleable thermoset composite materials which exhibit manufacturing cycle times of 3-minute or less, high speed impact performance on par with incumbent technologies, and defect-free consolidation of 3 dimensional parts. Government funding is required on this project because Mallinda is a start-up company whose focus is the development and scale-up of the described technology for introduction to the transportation segment. Unlike incumbent industry players, Mallinda is bringing a completely new and highly relevant malleable thermoset technology to bear on the problem of high throughput composites. As a small business, Mallinda relies on a combination of government R&D funding and private capital to perform development work.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reducing roughness and improving efficiency of MAPbI3 perovskite solar cells made by high-throughput photonic curing

For perovskite solar cells (PSCs) to be commercially viable, the slow and energy-insufficient thermal annealing step must be eliminated. Among the photo-irradiation methods proposed to replace thermal annealing, photonic curing is the fastest conversion method. Photonic curing delivers short (20 μs to 100 ms) but intense light pulses from a broadband (200-1500 nm) xenon flash lamp, making it the only method to convert perovskite under 20 ms. This processing time can be extrapolated to a roll-to-roll web speed of 40 m/min based on laboratory processing conditions. However, most reported PSCs made by photonic curing under 1 second have inferior performance (~10% PCE). Although SEM images show dense and pinhole-free perovskite films, AFM images indicate secondary wavy features of 500 nm-wide ridge and 80 nm-deep trenches on photonically cured perovskite films, the existence of which correlates with poor device performance. We suggest that this morphology feature is produced by volatile solvent evaporation during the fast photonic curing process. Two approaches have been made to remedy this issue: (1) adding CH2I2 as the third solvent in the conventional DMF-DMSO system and (2) applying a controlled air-blowing step before photonic curing to remove excess solvent further. Combining these two approaches produces photonically- cured perovskite films with a comparable film roughness and device performance. Alkyl halide additives have been reported to enhance PSC performance by modulated solvent-solute interactions and C-X (X = Cl, Br, and I) cleavage. Photonic curing can cleave CH2I2, producing disassociated iodide ions to replenish iodine loss induced by photonic curing, which is confirmed by EDX. As a co-solvent, the high boiling point of CH2I2 can also make the solvent less volatile, reducing surface roughness in photonically cured perovskite films. Additionally, photonically-cured perovskite films have longer PL lifetimes and a higher recombination resistance compared to thermally-annealed counterparts. As a result, we demonstrate that photonic curing is a suitable method to replace thermal annealing in high-throughput PSC fabrication.

14 SOLAR ENERGY↗
DOE OSTI2022

Transformational Membranes for Pre-Combustion Carbon Capture (Final Report)

The objectives of this project are to develop a cost-effective design and fabrication process of a novel transformational membrane and its membrane modules that capture CO 2 from coal derived syngas. We have synthesized transformational membranes, scaled up the membrane to a prototype size of 14 inches wide by 20 feet in continuous roll-to-roll fabrication, fabricated at least 9 prototype membrane modules (each with about 2.5-inch diameter, 14-inch length, and 800 cm 2 membrane area) for testing with simulated syngas at OSU to achieve capture with at least 95% CO 2 purity. The membrane modules are in commercial spiral-wound (SW) configuration with a minimal pressure drop (<0.103 bar/meter (1.5 psi/meter)).

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Second group of irradiation capsules: property data of irradiated welded stainless steel 347 and irradiated, welded, and hydrogen charged Zircaloy-4 for SHINE

Zircaloy-4 and AISI 347 stainless steel were irradiated to low doses (10 20 and 10 21 n/cm 2 ) at low temperature (~60°C) in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). These materials were under consideration for some of the structural components of the medical isotope production facility developed by SHINE Technologies. Zircaloy-4 base metal, as welded, welded and post-weld heat treated (PWHT), and hydrogen charged samples were irradiated. AISI 347 base metal from Sandmeyer Steel, Penn Stainless, and Rolled Alloys suppliers were irradiated. AISI 347 gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) samples of Penn Stainless and Rolled Alloys were also irradiated. The irradiated materials were tested with microhardness and tensile tests at room temperature in air. The AISI 347 materials had more elongation after irradiation than the Zircaloy-4 materials. In fact, the Zircaloy-4 welded without PWHT and with H charging had the lowest elongation of any of the materials. This report is the final in a series of reports on this project.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Continuous fiber malleable thermoset composites with sub-1-minute dwell times; validation of impact performance and evaluation of the efficacy of the compression forming process. CRADA Final Report

Mallinda is developing polyimine malleable thermoset prepreg composite materials which have excellent mechanical properties (100 GPa tensile modulus, 2 GPA tensile strength, 2.4% elongation at break) and high operating temperatures (Tg>200°C). At scale, polyimine resins are commensurate in price with commodity epoxy resins. What distinguishes malleable thermoset prepreg from traditional thermoset prepreg materials, is that they are fully cured during Mallinda’s roll-to-roll production of prepreg laminate. This results in 5 key value-differentiating benefits. First, it simplifies manufacturing logistics by enabling ambient transportation and storage, and by significantly extending out-life and shelf-life almost indefinitely. Second, elimination of autoclave curing reduces the economic and energy costs to the customer. Third, scrap rates can be reduced as malleable thermoset prepreg materials are directly reusable. Fourth, the manufacturing consolidation step can be roughly 10x faster than traditional thermosets, because the resin is already cured. Parts can be made via compression forming by the application of heat and pressure to quickly vitrify and consolidate a multilayer part – easily leading to sub 3-minute cycle times (at lab scale we have demonstrated a 20 second dwell time, with room for further optimization). Finally, the closed-loop cradle-to-cradle solution-based recyclability of malleable thermoset composites can also contribute significantly to the future of sustainable lightweight materials. The focus of this project was the development, optimization and validation of malleable thermoset composite materials which exhibit manufacturing cycle times of 3-minute or less, high speed impact performance on par with incumbent technologies, and defect-free consolidation of 3 dimensional parts.

36 MATERIALS SCIENCE↗
DOE OSTI2022

All Solid State Batteries Enabled by Multifunctional Electrolyte Materials

Solid Power has teamed with University of California San Diego to develop a high energy, long life, low cost, and safe all-solid-state-battery (ASSB). The battery is enabled by a multifunctional solid state electrolyte (SSE). The project enables scalable production of large format solid state batteries required by the vehicle market and building domestic battery manufacturers as leaders in the global vehicle ASSB production. In the project, the multifunctional SSE materials have been developed and optimized with ionic conductivity ≥ 5 mS/cm and electrochemical stability 0 – 4.5V. SSE separator films have been coated by using a roll-to-roll process with thickness ≤ 40 µm. All-solid-state NMC-Li pouch cells containing the developed SSE have been assembled. A cycle life of > 750 at 100% DOD and 45 °C has been demonstrated in a full pouch cell.

25 ENERGY STORAGE↗
DOE OSTI2022

Development and Demonstration of a Fuel-Efficient, Class 8 Tractor & Trailer Engine System (SuperTruck II)

Navistar presents the SuperTruck II (ST II) Final Report to the Unites States Department of Energy (US DOE), which covers the five Budget Periods (BPs) from 10-1-2016 through 6-30-2022. For ST II, Navistar built on the achievements of the SuperTruck I (ST I) Program as a catalyst to continue critical research, design and development, testing, and operations to reach the ambitious goals of the ST II project. This approach allowed Navistar to continue contributing to the essential needs of our nation for safe, efficient, and cost-effective delivery of goods and services, as we reduced negative environmental effects and improved operational productivity. This document contains information specified in DOE F 4600.2, Final Scientific/Technical Report DOE F 241.3, B. SCIENTIFIC/TECHNICAL REPORTS, explaining how we met and exceeded program requirements. Throughout this Final Report, Navistar extracted information from documents prepared during the project that represent our management, design and development, building, and testing efforts to meet and exceed SuperTruck II project goals. Navistar followed Plan requirements to achieve / exceed Project Objectives: a) >100% improvement in vehicle freight efficiency (FE) (on ton-MPG basis) relative to 2009 baseline with stretch goal of 140% improvement [actual: 170%); b) >55% engine brake thermal efficiency (BTE) demonstrated in operational engine at a 65-mph cruise point on a dynamometer – ≥31% increase from 2009 baseline [actual: 55.20% of combined BTE) ; and c) development and implementation of commercially cost effective technologies (in terms of a simple payback). Technology selection / development path focused on developing technologies applicable for production within 3-year approach, while ensuring technology readiness and cost of ownership for end users. The Program was organized into five budget periods: Requirements / Technology Assessment and Initial Hardware Testing; Technology Development and Concept Readiness Demonstration; Technology Finalization and Validation Tractor / Trailer Fabrication, Integration and Commissioning Demonstration; and Fuel Economy (FE) and Brake Thermal Efficiency (BTE) and Program Completion. Leadership was provided by DOE, with tasks performed by laboratories (Argonne National Laboratory, Lawrence Livermore National Laboratory); partners at Bosch, TPI, Dana, and J.B. Hunt; , and support from University of Michigan and Clemson University. Navistar lead this team with Principal Investigator / Contracting Officer; Project Manager (PM); Vehicle, Engine, and Aftertreatment Engineers; Finance Manager, Technical Program Leads, and Legal/IP; and other key personnel. Work also included personnel in risk management; funding / budget / finance. Work involved analysis, development, testing, and down selection of individual/system engine, aftertreatment, and vehicle technologies, with integration of selected technologies into a prototype vehicle for demonstration of fuel-efficiency gain. Work also included component/integrated system level development of truck and trailer aerodynamics, base engine efficiency, advanced aftertreatment, combustion efficiency, waste heat recovery, hybrid powertrain, reduced rolling resistance, weight reduction, idle reduction, and driver feedback. As ST II progressed, Navistar performed computer-based modeling / simulations of technologies focused on the primary operational areas: Engine, Aftertreatment, and Vehicle. During the ST II Program, the COVID Virus outbreak unexpectedly challenged by the effects of, which affected staffing, scheduling, design, supplies, availability of materials, production procedures, and testing. The DOE responded by extending the program by three quarters to ensure that project tasks were completed for this vital project. Focus continued on analyzing, developing, testing, and down selecting individual-/system-level engine and vehicle technologies for integration of the final selected technologies into a prototype vehicle that would demonstrate fuel-efficiency gains made possible through these technologies. This included component/integrated system-level development of truck and trailer aerodynamics, base engine efficiency, advanced aftertreatment, combustion efficiency, waste heat recovery, solar power, distributed and intelligent vehicle power, hybrid powertrain, reduced rolling resistance, weight reduction, idle reduction, and driver feedback. Throughout the program, function, reliability, and performance at all levels were ensured through testing. Proof of this approach was demonstrated in multiple, on-road demonstrations: Scenario A (Flatland) Fuel Economy, Scenario B (Hilly) Fuel Economy, and City Cycle Tests. Other benefits derived from ST II included new/improved products, publications, patents, and next-step capabilities related to electric/hydrogen vehicles and autonomous driving.

Zukouski, Russ↗
DOE OSTI2022

Silver Nanowire-Indium Zinc Oxide Composite Flexible Transparent Conducting Electrodes Made by Spin- coating and Photonic Curing

Realizing high-throughput, low-cost perovskite solar cell (PSC) manufacturing is highly sought-after in photovoltaic (PV) research in recent years. To fully achieve roll-to-roll (R2R) manufacturing of PSCs, it is important to consider the flexible transparent electrode (TE). PET/ITO is a commonly used substrate for making flexible PSCs. When optimizing transparent conducting materials, there is a tradeoff between sheet resistance (Rsh) and optical transparency. Because commercial PET/ITO substrates are made with slow (~1 m/min) vacuum deposition processes, they tend to be expensive. Therefore, it would be advantageous to develop a high-throughput, R2R compatible, solution-deposition approach for fabricating the TE on PET substrates. While various solution-deposition processes, such as blade coating or slot-die coating, can achieve the desired web speed of > 10 m/min, there is still a need to improve the post-deposition annealing step. One promising post-deposition processing technique is intense-pulsed-light processing, also known as photonic curing. Photonic curing delivers short (0.01 – 100 ms) pulses of broadband (200 – 1500 nm) light from a xenon flash lamp to the samples. Any materials in the sample stack that absorb light will convert the impinging light pulse into heat within the sample, which drives changes in the sample (calcination, phase change, crystallization, etc.). Photonic curing has three main advantages over thermal annealing: 1. Faster processing speed (milliseconds or seconds). 2. Compatibility with plastic substrates. 3. Smaller physical footprint and less wasted energy. Since the light pulses are on for a short time, the intensity can be high while the total energy delivered to the sample is low, minimizing damages to the plastic substrates. In this work, a hybrid TE material is fabricated on PET substrates using photonic curing. The hybrid TE material contains a layer of silver nanowires (AgNWs) and a layer of metal-oxide (InOx, ITO, IZO, etc.). The AgNWs increase the light absorbed by the film during the photonic curing process, which leads to higher processing temperatures, possibly improving the conversion of the metal-oxide layer. The AgNWs also enhance the electrical conductivity of the final TE layer after photonic curing. A AgNW and metal-oxide bilayer is formed by spin coating each solution onto the PET substrate sequentially followed by a single photonic curing process. We use average optical transmittance (Tavg) from 400 to 700 nm and average Rsh to evaluate the TE performance. The following photonic curing parameters are varied to optimize Tavg (maximize) and Rsh (minimize): Pulse voltage, pulse envelope, number of micro-pulses, duty cycle, number of pulses, and pulse repetition rate. Preliminarily, we also observe a significant impact on the TE properties by the volume of AgNW deposited during the spin coating deposition step. Using dispense volumes of 80 µL and 20 µL, we achieve samples with Tavg = 73%, Rsh = 19 Ω/sq, and roughness = 9 nm, and Tavg = 83%, Rsh = 58 Ω/sq, and roughness = 5.6 nm, respectively, after photonic curing.

14 SOLAR ENERGY↗
DOE OSTI2022

Scalable Deposition of NiOxas a Hole Transport Layer for Perovskite Solar Cells on PET Substrates

Transition from laboratory scale fabrication to large scale perovskite fabrication processes remains a challenge. Upscaling perovskite fabrication requires the development of deposition methods that yield uniform charge transport layers at scale. By optimizing ink composition, we have developed a doped nickel oxide hole transport material for uniform large area deposition on a roll-to-roll system with a peak power conversion efficiency of 11.2%.

Armstrong, Peter↗
DOE OSTI2023

Bio-Based Phase Change Materials (PCMs) for Thermal Energy Storage (Final Scientific/Technical Report)

The goal of this project is to develop a novel bio-based phase change material (PCM) derived from squid ring teeth (SRT) proteins, and design a prototype heat exchanger based on these bio-based PCMs for energy storage and dynamic heat exchange for building thermal energy storage systems. The PCMs, derived from SRT proteins, will demonstrate room temperature energy storage capacities and switchable thermal conductivities that redefine the current state-of-the-art (SOA) for building thermal energy storage. Further, in a single material and with a single manufacturing processes, our proposed thermal battery will be developed with “on demand” thermal conductivity for rapid charging/discharging but superior insulation during energy storage periods. More specifically, our bio-based PCMs have demonstrated: 1) the potential for increased energy storage capacity (i.e., greater than paraffines at room temperature); 2) tunability in thermal conductivity with the largest thermal conductivity switching ratios for an intrinsic material reported to date, and 3) a 100% recyclable and biodegradable PCM with low volatility and toxicity and scalability in its manufacture for both residential and commercial applications. The already established ability for roll-to-roll processing of these non-toxic, non-flammable SRT composites along with their carbon-neutral manufacturing processes that has been pioneered by our team make this solution a disruptive and impactful technology to redefine the current SOA of energy storage technologies. The outcomes of this effort have been: 1) the identification of new bio-based PCM that establishes a new SOA for thermal conductivity and energy storage density at room temperature and 2) the development of a new experimental technique to measure the energy storage density via latent heat measurements during melting of thin films. This new technique can be applied to thin films (as thin as < 1 micrometer), and represents a novel approach for thin film energy storage density measurements. Dynamic thermal energy storage is the missing technology that will enable a grid- interactive efficient building (GEB). For a “smart” building capable of connecting with the power grid, the media must be inexpensive and possess thermal switching capabilities to control the time-dependent heat flow into (and out of) the PCM on demand. Unique to the material system in this program, programmable SRT-based PCM show improvements as compared to traditionally used PCMs, and thus its technical performance will represent a leap forward for the future GEB concept.

25 ENERGY STORAGE↗
DOE OSTI2023

Novel Transformational Membranes and Process for CO 2 Capture from Flue Gas (FE0031731)

The objectives of this project are to develop a cost-effective design and fabrication process for a novel transformational membrane and its membrane modules that capture CO 2 from flue gas. Optimization of the novel transformational membrane, scale-up of the membrane to a prototype size of about 20" wide in continuous roll-to-roll fabrication, and construction and testing of a skid for the integrated membrane process will be performed. For the design of this membrane, we use a cost-effective polymer support and coat a thin top layer of the membrane. The simplicity of this membrane design offers a low cost for the membrane element in commercial spiral-wound (SW) configuration (<$2.00/ft 2 or $21.5/m 2 ). The prototype membrane will be used to fabricate 6 pilot-size membrane modules (each about 20" length, 3 modules each at the commercial-size diameter of 8 inches with 35 m 2 membrane area for Stage 1 and 3 modules each at 5-inch diameter with 12 m 2 membrane area for Stage 2) for testing with simulated flue gas at OSU and with actual flue gas at the National Carbon Capture Center, Wilsonville, AL using the skid to capture the CO 2 (at 60 – 90%) with at least 95% CO 2 purity. The prototype membrane modules will be in commercial SW configuration with a minimal pressure drop (<0.103 bar/meter (1.5 psi/meter)). These objectives have been achieved successfully.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Main Bearing Replacement and Damage - A Field Data Study on 15 Gigawatts of Wind Energy Capacity

This study seeks to establish a comprehensive baseline of knowledge for the replacement and damage of main bearings in wind turbines. The purpose of this report is to provide a high-level summary of the data set, methodology, and results of this work. Full technical details and an extended analysis will be made available in a future publication. We collected data on main bearing replacements and reported damage from industrial partners based in Europe and the United States. In total, we obtained data for 167 wind power plants, with a combined capacity of 15.3 gigawatts (GW). Most of the data set was comprised of land-based, three-point mount, spherical roller bearings. Within this data set were 689 instances of main bearing replacement. Analysis was undertaken in two parts: first, a statistical analysis of the main bearing time-to-replacement data using survival analysis techniques; second, quantitative and qualitative analyses of the obtained damage information. Our results showed that 10% of a fixed main bearing population would be expected to have been replaced by 10.5 years. This is close to half of the 20-year design value. Fitted parametric distributions then indicated that by year 20, between 22% and 25% of main bearings are expected to have been replaced. Analysis of the damage reports revealed spalling to be the main type of damage listed. The additional presence of surface damage in the collected data indicates that at least part of the spalling cases are likely due to surface-initiated rolling contact fatigue. At this stage is not clear what proportion of spalling cases result from "wear induced", surface-initiated and subsurface-initiated rolling contact fatigue. While this work provides important insights into the current state of main bearing replacements and damage, many questions remain. An ongoing and expanding data collection and analysis effort focused on wind turbine main bearings is therefore recommended.

17 WIND ENERGY↗
DOE OSTI2024

Solid State Li Ion Batteries Using Si Composite Anodes

Solid Power has teamed with Argonne National Laboratory (ANL) to develop an all solid-state lithium-ion battery (ASSB), enabled by a high-capacity Si anode and a solid state electrolyte (SSE). Replacing liquid electrolytes with solid electrolytes addresses the calendar life challenges that currently limit the widespread adoption of Si anodes. In this project, Si-SSE composite materials have been developed with a specific capacity >1500 mAh/g (at electrode level). A Si anode was coated by using a roll-to-roll process. All-solid-state NMC-Si pouch cells have been assembled and tested. Cycle life of 1100 at 100% DOD has been demonstrated in the solid state Si pouch cell. Excellent calendar life is achieved in the cell via a high temperature storage test.

25 ENERGY STORAGE↗
DOE OSTI2024

Multifunctional Nanofiber Reinforcement for Improved Thermomechanical and Chemical Stability of Perovskite Solar Cells

This project focused on the development of metal halide perovskite-polymeric nanofiber nanocomposites for robust and efficient solar cells. Metal halide perovskite solar cells are a potentially disruptive technology with high efficiencies and low-cost solution processability amenable with roll-to-roll fabrication of flexible devices. However, perovskites exhibit extreme brittleness, high internal film stresses, and chemical instabilities that significantly limit service lifetimes under normal operating conditions. To date, most work addressing these shortcomings has been focused on encapsulating devices between thick layers of rigid materials such as glass, which increases the total weight and cost of devices. Furthermore, these rigid and heavy encapsulants do not translate well to emerging solar markets vital for national security, including integrated mobile power, emergency deployments for disaster relief and military engagement, and lightweight power for space. It is therefore critical to improve the thermomechanical and chemical stability of perovskite devices in a way that is compatible with flexible and lightweight substrates. In this project, we integrated nylon-6,6 nanofibers into MAPbI3 to mechanically reinforce the perovskite, demonstrating films that exhibited fracture energies 5-fold greater than pristine MAPbI3 while also maintaining similar power conversion efficiencies due to beneficial light scattering effects from the polymeric nanofibers. These results required successful development of approaches to control the deposition thickness of nanofiber mats down to 100s of nanometers, and to ensure the polymer nanofibers did not inhibit charge transport to the at the perovskite-transport layer interface.

14 SOLAR ENERGY↗
DOE OSTI2024

Lifetime Energy Savings Via Advanced Manufacturing of Low Density Steels for Transportation Applications

The purpose of this “Low Density Steels for Transportation Applications” project was to develop an alloy composition and processing parameters that would result in a material suitable for use in automotive structural components at a reduced density over the current advanced high strength steel (AHSS) materials used. The project work successfully developed a robust alloy capable of exceeding project mechanical property targets at each stage of development, with an 8% density reduction over benchmark AHSS materials (7.8 g/cm3). The developed alloy has the potential to offer significant vehicle lightweighting and improved fuel economy, without sacrificing the increased passenger safety of more traditional AHSS. Through the three tasks of the project, (1) Alloy design and small-scale laboratory evaluation, (2) Laboratory development of hot rolled material and (3) Laboratory development of a cold rolled material, the laboratory work utilized advanced characterization and analytical methods on novel alloy compositions subjected to both conventional and non-conventional processing operations.

36 MATERIALS SCIENCE↗