Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REACTION CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Appendix A: Proposed statement of work, 1994

This NRA effort is devoted to developing new techniques and methodologies which utilize and/or provide support to Integrated Vehicle Health Management (IVHM) concepts and techniques, modern design processes, and open architectures to realize an avionics system architecture that relieves the flight control system (FCS) of the requirement of maintaining intimate knowledge and control of the vehicle subsystems (for instance, the reaction control system (RCS)). The benefit of this architecture is that future upgrades and enhancements to the system(s) or to individual components within the system(s) are greatly simplified. This approach also allows a much more straightforward treatment of failure analysis, system diagnosis, and the design of fault containment domains. This NRA effort is also devoted to realizing capabilities to provide an available avionics system (and subsystem(s)) at minimum operational cost. This thrust provides a direct benefit to NASA in that it seeks to accelerate the design cycle to allow state of the art components and designs to actually appear in the fielded system rather than merely in the initial design. To achieve this, this effort is intended to benefit from efforts already underway at Lockheed and other major contractors. For instance, Lockheed Sanders is currently engaged in a major DoD funded development program which has the goal of cutting design cycle time of high performance electronics by a factor of four while simultaneously improving quality also by a factor of four. The early work on this program was used to enable the rapid prototyping of the Reaction Jet Drive Controller which was accomplished in 1993. Similarly, maximum leverage will be derived from recent NASA and DoD efforts to increase the content of high quality commercial grade electronic components in systems for aerospace applications. Both of these goals result in a system with enhanced cost effectiveness, increased reliability, and greatly increased performance compared to a system developed using a more conventional approach.

Source record↗
NASA NTRS2013

Fault Protection Design and Testing for the Cassini Spacecraft in a "Mixed" Thruster Configuration

NASA's Cassini Spacecraft, launched on October 15th, 1997 and arrived at Saturn on June 30th, 2004, is the largest and most ambitious interplanetary spacecraft in history. In order to meet the challenging attitude control and navigation requirements of the orbit profile at Saturn, Cassini is equipped with a monopropellant thruster based Reaction Control System (RCS), a bipropellant Main Engine Assembly (MEA) and a Reaction Wheel Assembly (RWA). In 2008, after 11 years of reliable service, several RCS thrusters began to show signs of end of life degradation, which led the operations team to successfully perform the swap from the A-branch to the B-branch RCS system. If similar degradation begins to occur on any of the B-branch thrusters, Cassini might have to assume a "mixed" thruster configuration, where a subset of both A and B branch thrusters will be designated as prime. The Cassini Fault Protection FSW was recently updated to handle this scenario. The design, implementation, and testing of this update is described in this paper.

propellant↗
NASA NTRS2010

A Flight-Calibrated Methodology for Determination of Cassini Thruster On-Times for Reaction Wheel Biases

This paper describes a methodology for accurate and flight-calibrated determination of the on-times of the Cassini spacecraft Reaction Control System (RCS) thrusters, without any form of dynamic simulation, for the reaction wheel biases. The hydrazine usage and the delta V vector in body frame are also computed from the respective thruster on-times. The Cassini spacecraft, the largest and most complex interplanetary spacecraft ever built, continues to undertake ambitious and unique scientific observations of planet Saturn, Titan, Enceladus, and other moons of Saturn. In order to maintain a stable attitude during the course of its mission, this three-axis stabilized spacecraft uses two different control systems: the RCS and the reaction wheel assembly control system. The RCS is used to execute a commanded spacecraft slew, to maintain three-axis attitude control, control spacecraft's attitude while performing science observations with coarse pointing requirements, e.g. during targeted low-altitude Titan and Enceladus flybys, bias the momentum of reaction wheels, and to perform RCS-based orbit trim maneuvers. The use of RCS often imparts undesired delta V on the spacecraft. The Cassini navigation team requires accurate predictions of the delta V in spacecraft coordinates and inertial frame resulting from slews using RCS thrusters and more importantly from reaction wheel bias events. It is crucial for the Cassini spacecraft attitude control and navigation teams to be able to, quickly but accurately, predict the hydrazine usage and delta V for various reaction wheel bias events without actually having to spend time and resources simulating the event in flight software-based dynamic simulation or hardware-in-the-loop simulation environments. The methodology described in this paper, and the ground software developed thereof, are designed to provide just that. This methodology assumes a priori knowledge of thrust magnitudes and thruster pulse rise and tail-off time constants for eight individual attitude control thrusters, the spacecraft's wet mass and its center of mass location, and a few other key parameters.

Earth Mean Equatorial↗
NASA NTRS1971

The quasi-inertial and wide-deadband modes as backup attitude options for the Skylab mission

The quasi-inertial (QI) and wide deadband (WDB) modes were investigated as alternatives to the solar inertial (SI) mode in case two control moment gyros fail during the Skylab mission. Both modes provide a substantial reduction in propellant requirements from the solar interial hold requirement with either the orbital assembly/thruster attitude control system or service module reaction control system. Spacecraft motion in the QI mode is produced by a command rate and results in a small amplitude oscillation (17 deg, maximum) about the SI orientation. In the WDB mode a somewhat similar, but larger amplitude motion (35 deg maximum) about the SI orientation is developed by appropriate choice of controller deadbands and switch line slopes.

Elrod, B. D.↗
NASA NTRS1975

Space Shuttle flight control system

The Space Shuttle is a control stabilized vehicle with control provided by an all digital, fly-by-wire flight control system. This paper gives a description of the several modes of flight control which correspond to the Shuttle mission phases. These modes are ascent flight control (including open loop first stage steering, the use of four computers operating in parallel and inertial guidance sensors), on-orbit flight control (with a discussion of reaction control, phase plane switching logic, jet selection logic, state estimator logic and OMS thrust vector control), entry flight control and TAEM (terminal area energy management to landing). Also discussed are redundancy management and backup flight control.

Klinar, W. J.↗
NASA NTRS1981

Piloted simulation of hover and transition of a vertical attitude takeoff and landing aircraft

Piloted simulation studies of candidate control systems for VATOL aircraft were conducted on a six degree of freedom simulator. Hover and transitions from wing-born to hovering flight were performed, with and without turbulence, on a representative high performance fighter configuration. Deflection of the rear engine nozzle provided pitch and yaw control moments in concert with reaction controls for roll. Unique motion cues in hover result from the vertical displacement of the cockpit and the thrust vectoring nozzles. Abundant control power available with moderate engine nozzle deflection combined with rate feedback for stability augmentation provided very satisfactory control.

Hill, G. C.↗
NASA NTRS1987

Robust control for large space antennas

A brief description of program objectives and the space based radar application is given. General characteristics of the 100 m diameter reflector spacecraft are described along with the intended mission and associated requirements, and dynamic characteristics relevant to that mission. Preliminary control analyses are carried out for the critical rapid slew and settle maneuver to establish feedback control requirements and fundamental limitations in meeting those requirements with control hardware for a baseline reaction control system (RCS) jet placement assumed for the open loop bang-bang slew limitations. Control moment gyros (CMGs), angular position sensors, and linear translation sensors are placed for feedback control. Control laws are designed for the improved sensor and actuator placement and evaluated for performance and robustness to unstructured model uncertainty. The robustness of the control design is assessed with respect to modal parameter uncertainty. Results of the control designs analyses are summarized, conclusions are drawn, and recommendations made for future studies.

Barrett, M. F.↗
NASA NTRS1990

Biconic cargo return vehicle with an advanced recovery system

The current space exploration initiative is focused around the development of the Space Station Freedom (SSF). Regular resupply missions must support a full crew on the station. The present mission capability of the shuttle is insufficient, making it necessary to find an alternative. One alternative is a reusable Cargo Return Vehicle (CRV). The suggested design is a biconic shaped, dry land recovery CRV with an advance recovery system (ARC). A liquid rocket booster will insert the CRV into a low Earth orbit. Three onboard liquid hydrogen/liquid oxygen engines are used to reach the orbit of the station. The CRV will dock to the station and cargo exchange will take place. Within the command and control zone (CCZ), the CRV will be controlled by a gaseous nitrogen reaction control system (RCS). The CRV will have the capability to exchange the payload with the Orbital Maneuvering Vehicle (OMV). The bent biconic shape will give the CRV sufficient crossrange to reach Edwards Air Force Base and several alternative sites. Near the landing site, a parafoil-shaped ARS is deployed. The CRV is designed to carry a payload of 40 klb, and has an unloaded weight of 35 klb.

Source record↗
NASA NTRS1993

Control/structure interaction during Space Station Freedom-Orbiter berthing

The berthing maneuver is essential for the construction and assembly of Space Station Freedom (SSF) and has a direct effect on the SSF assembly build up and SSF/Orbiter operations. The effects of flexible body dynamics coupled with the available control system may impose new requirements on the maneuver. The problem is further complicated by the effect of the SSF control system on the Shuttle Remote Manipulator System (SRMS). These effects will play a major role in the development of operational requirements which need to be identified and validated in order to assure total safety and maneuver execution during SSF construction. This paper presents the results of ongoing studies to investigate the Control/Structure Interaction (CSI) during the berthing operations. The problem is formulated in terms of multi-flex body equations of motion for SSF and the SRMS and on-orbit flight control systems for the SRMS and the SSF, which includes the Control Moment Gyro (CMG) and Reaction Control System (RCS) Attitude Control Systems (ACS). The SSF control system designs are based on the Preliminary Design Review (PDR) version of the Honeywell design. The simulation tool used for the analysis is briefly described and the CSI results are presented for given berthing scenarios.

Hua, Tuyen↗
NASA NTRS1997

Iridium-Coated Rhenium Radiation-Cooled Rockets

Radiation-cooled rockets are used for a range of low-thrust propulsion functions, including apogee insertion, attitude control, and repositioning of satellites, reaction control of launch vehicles, and primary propulsion for planetary space- craft. The key to high performance and long lifetimes for radiation-cooled rockets is the chamber temperature capability. The material system that is currently used for radiation-cooled rockets, a niobium alloy (C103) with a fused silica coating, has a maximum operating temperature of 1370 C. Temperature limitations of C103 rockets force the use of fuel film cooling, which degrades rocket performance and, in some cases, imposes a plume contamination issue from unburned fuel. A material system composed of a rhenium (Re) substrate and an iridium (Ir) coating has demonstrated operation at high temperatures (2200 C) and for long lifetimes (hours). The added thermal margin afforded by iridium-coated rhenium (Ir/Re) allows reduction or elimination of fuel film cooling. This, in turn, leads to higher performance and cleaner spacecraft environments. There are ongoing government- and industry-sponsored efforts to develop flight Ir/ Re engines, with the primary focus on 440-N, apogee insertion engines. Complementing these Ir/Re engine development efforts is a program to address specific concerns and fundamental characterization of the Ir/Re material system, including (1) development of Ir/Re rocket fabrication methods, (2) establishment of critical Re mechanical properly data, (3) development of reliable joining methods, and (4) characterization of Ir/Re life-limiting mechanisms.

Reed, Brian D.↗
NASA NTRS2016

Orion GN&C Detection and Mitigation of Parachute Pendulosity

New techniques being employed by Orion guidance, navigation, and control (GN&C) using a reaction control system (RCS) under parachutes are described. Pendulosity refers to a pendulum-oscillatory mode that can occur during descent under main parachutes and that has been observed during Orion parachute drop tests. The pendulum mode reduces the ability of GN&C to maneuver the suspended vehicle resulting in undesirable increases to structural loads at touch-down. Parachute redesign efforts have been unsuccessful in reducing the pendulous behavior necessitating GN&C mitigation options. An observer has been developed to estimate the pendulum motion as well as the underlying wind velocity vector. Using this knowledge the control system maneuvers the vehicle using two separate strategies determined by a wind velocity magnitude threshold; at high wind velocities the vehicle is aligned with the wind direction and for cases with lower wind velocities the vehicle is aligned such that it is perpendicular to the swing plane. Pendulum damping techniques using RCS thrusters are discussed but have not been selected for use onboard the Orion spacecraft. The techniques discussed in this paper will be flown on Exploration Mission 1 (EM-1).

Kane, Mark A.↗
NASA NTRS2016

Orion GN&C Detection and Mitigation of Parachute Pendulosity

New techniques being employed by Orion guidance, navigation, and control (GN&C) using a reaction control system (RCS) under parachutes are described. Pendulosity refers to a pendulum-oscillatory mode that can occur during descent under main parachutes and that has been observed during Orion parachute drop tests. The pendulum mode reduces the ability of GN&C to maneuver the suspended vehicle resulting in undesirable increases to structural loads at touchdown. Parachute redesign efforts have been unsuccessful in reducing the pendulous behavior necessitating GN&C mitigation options. An observer has been developed to estimate the pendulum motion as well as the underlying wind velocity vector. Using this knowledge, the control system maneuvers the vehicle using two separate strategies determined by wind velocity magnitude and pendulum energy thresholds; at high wind velocities the vehicle is aligned with the wind direction and for cases with lower wind velocities and large pendulum amplitudes the vehicle is aligned such that it is perpendicular to the swing plane. Pendulum damping techniques using RCS thrusters are discussed but have not been selected for use onboard the Orion spacecraft. The techniques discussed in this paper will be flown on Exploration Mission 1 (EM-1).

Kane, Mark A.↗
NASA NTRS2020

Pterodactyl: Control Architectures Development for Integrated Control Design of a Mechanically Deployed Entry Vehicle

The need to return high mass payloads is driving the development of a new class of vehicles, Deployable Entry Vehicles (DEV) for which feasible and optimized control architectures have not been developed. The Pterodactyl project, seeks to advance the current state-of-the-art for entry vehicles by developing a design, test, and build capability for DEVs that can be applied to various entry vehicle configurations. This paper details the efforts on the NASA-funded Pterodactyl project to investigate multiple control techniques for the Lifting Nano-ADEPT (LNA) DEV. We design and implement multiple control architectures on the LNA and evaluate their performance in achieving varying guidance commands during entry.First we present an overview of DEVs and the Lifting Nano-ADEPT (LNA), along with the physical LNA configuration that influences the different control designs. Existing state-of-the-art for entry vehicle control is primarily propulsive as reaction control systems (RCS) are widely employed. In this work, we analyze the feasibility of using both propulsive control systems such as RCS to generate moments, and non-propulsive control systems such as aerodynamic control surfaces and internal moving mass actuations to shift the LNA center of gravity and generate moments. For these diverse control systems, we design different multi-input multi-output (MIMO) state-feedback integral controllers based on linear quadratic regulator (LQR) optimal control methods. The control variables calculated by the controllers vary, depending on the control system being utilized and the outputs to track for the controller are either the (i) bank angle or the (ii) angle of attack and sideslip angle as determined by the desired guidance trajectory. The LQR control design technique allows the relative allocation of the control variables through the choice of the weighting matrices in the cost index. Thus, it is easy to (i) specify which and how much of a control variable to use, and (ii) utilize one control design for different control architectures by simply modifying the choice of the weighting matrices.By providing a comparative analysis of multiple control systems, configurations, and performance, this paper and the Pterodactyl project as a whole will help entry vehicle system designers and control systems engineers determine suitable control architectures for integration with DEVs and other entry vehicle types.

Okolo, Wendy A.↗
NASA NTRS2020

Pterodactyl: Control System Demonstrator Development for Integrated Control Design of a Mechanically Deployed Entry Vehicle

The NASA-funded Pterodactyl project is a design, test, and build capability to (i) advance the current state of the art for Deployable Entry Vehicle (DEV) guidance and control (G&C), and (ii) determine the feasibility of control system integration for various entry vehicle types including those without aeroshells. This capability is currently being used to develop control systems for one such unconventional entry vehicle, the Lifting Nano-ADEPT (LNA) vehicle. ADEPT offers the possibility of integrating control systems directly onto the mechanically deployed structure and building hardware demonstrators will help assess integration and design challenges. Control systems based on aerodynamic control surfaces, mass movement, and reaction control systems (RCS) are currently being investigated for a down-select to the most suitable control architecture for the LNA.To that effect, in this submission, we detail the efforts of the Pterodactyl project to develop a series of hardware demonstrators for the different LNA control systems. Rapid prototypes, for a set of quarter- model or eighth-model vehicle segments, will be developed for all three architectures to validate mechanical design assumptions, and hardware-in-the-loop (HIWL) control approaches. A ground test control system demonstrator will be designed and built after the trade study is complete. The industrial-grade demonstrator will be designed so that it can be incorporated into a HWIL simulation to further validate the findings of the initial trade study. The HWIL simulation will leverage the iPAS environment developed at NASA's Johnson Space Center which facilitates integration testing to support technology maturation and risk reduction, necessary elements for the hardware demonstration development detailed in this paper.

Margolis, Benjamin W.↗
NASA NTRSDate not supplied

Integrated Design Results for the MSR SRC Mars Ascent Vehicle

The primary mission of the NASA Mars Sample Return (MSR) Campaign is to return samples of the Martian surface to Earth for scientific study. As part of this campaign, NASA is developing a Mars Ascent Vehicle (MAV). This vehicle must survive an approximate two year journey to the Martian surface as a payload aboard a separate lander spacecraft. After residing on the surface for another year, the MAV will carry a payload of samples into orbit. From there, following ejection from the MAV, the samples will rendezvous with an Earth return spacecraft for capture, and ultimately, return to Earth.The design of the MAV represents a number of unique challenges, as no launch vehicle has ever left the surface of a planet other than Earth. Although conceptual designs for a MAV have been in various levels of development since the 1970s, none have achieved the level of fidelity and support that exists in the current MSR-MAV design. Early MSR-MAV concept studies examined multiple methods of propulsion, ultimately deciding that a Two Stage to Orbit (TSTO) solid propulsion vehicle would provide the most capable performance in a Martian environment. Following this key architecture decision, the vehicle design was further matured to a Solid-Solid Guided-Guided (SSGG) architecture for NASA Key Decision Point A (KDP-A). Although the SSGG design was able to meet all mission constraints, concerns were raised regarding limited mass margin on other elements of the MSR campaign at such an early phase. A design challenge was issued to reduce MAV total mass by as much as possible. It was ultimately determined that by moving a number of components of the vehicle second stage to the first stage, the overall vehicle mass could be reduced significantly. The new design featured a much smaller and completely unguided second stage. This paper describes the resultant Solid-Solid Guided-Unguided (SSGU) MAV design concept developed as part of the Systems Requirement Cycle (SRC). This design was developed primarily by NASA Marshall Space Flight Center (MSFC), in association with NASA Jet Propulsion Laboratory (JPL) and NASA Langley Research Center (LaRC). The TSTO vehicle includes one solid rocket motor per stage. As the vehicle second stage is unguided, it features spin-stabilization to maintain vehicle stability during flight. An electromechanically actuated Thrust Vector Control (TVC) and a monopropellant Reaction Control System (RCS) is employed for active guidance on the first stage. The vehicle is designed to deliver up to 0.47kg of Martian samples to a Mars circular orbit of 380km at 27° inclination. Due to the extremely unique design constraints of this mission, and a recent transition to a Risk Class A posture, the MAV team was compelled to devise unconventional solutions to the vehicle design. The detailed design and analysis of these subsystems and the vehicle as a whole are discussed in this paper relative to all of the engineering disciplines involved.

MSR↗
DOE OSTI2022

Control of Surface Chemical Reactions through Solid Stiffness

Control of surface reactions is commonly achieved by modification of surface electronic structures. Here, we discover an alternative pathway for controlling surface reactions by tuning the mechanical stiffness of the underlying material. We find that in addition to the typically assumed surface electronic contribution right at the reactive site, the contribution from the deformation of the bulk region plays a vital role in controlling surface reactions. The underlying mechanism is an elastic relaxation of the solid, which depends on the material’s stiffness and can be modified by tuning bulk stoichiometry. The effect of bulk stiffness on surface reactions has been demonstrated by considering hydrogen scission reaction and oxygen incorporation reaction during corrosion of amorphous SiC in water and air, respectively. Finally, our results imply that tuning of bulk stiffness by modifying stoichiometry can provide an effective method for controlling surface reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Defect-driven selective metal oxidation at atomic scale

Nanoscale materials modified by crystal defects exhibit significantly different behaviours upon chemical reactions such as oxidation, catalysis, lithiation and epitaxial growth. However, unveiling the exact defect-controlled reaction dynamics (e.g. oxidation) at atomic scale remains a challenge for applications. Here, using in situ high-resolution transmission electron microscopy and first-principles calculations, we reveal the dynamics of a general site-selective oxidation behaviour in nanotwinned silver and palladium driven by individual stacking-faults and twin boundaries. The coherent planar defects crossing the surface exhibit the highest oxygen binding energies, leading to preferential nucleation of oxides at these intersections. Planar-fault mediated diffusion of oxygen atoms is shown to catalyse subsequent layer-by-layer inward oxide growth via atomic steps migrating on the oxide-metal interface. These findings provide an atomistic visualization of the complex reaction dynamics controlled by planar defects in metallic nanostructures, which could enable the modification of physiochemical performances in nanomaterials through defect engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗