Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Epitaxial Growth of Large-Scale 2D CrTe 2 Films on Amorphous Silicon Wafers With Low Thermal Budget

2D van der Waals (vdW) magnets open landmark horizons in the development of innovative spintronic device architectures. However, their fabrication with large scale poses challenges due to high synthesis temperatures (>500 °C) and difficulties in integrating them with standard complementary metal-oxide semiconductor (CMOS) technology on amorphous substrates such as silicon oxide (SiO 2 ) and silicon nitride (SiN x ). Here, a seeded growth technique for crystallizing CrTe 2 films on amorphous SiN x /Si and SiO 2 /Si substrates with a low thermal budget is presented. This fabrication process optimizes large-scale, granular atomic layers on amorphous substrates, yielding a substantial coercivity of 11.5 kilo-oersted, attributed to weak intergranular exchange coupling. Field-driven Néel-type stripe domain dynamics explain the amplified coercivity. Moreover, the granular CrTe 2 devices on Si wafers display significantly enhanced magnetoresistance, more than doubling that of single-crystalline counterparts. Current-assisted magnetization switching, enabled by a substantial spin–orbit torque with a large spin Hall angle (85) and spin Hall conductivity (1.02 × 10 7 ℏ/2e Ω -1 m -1 ), is also demonstrated. These observations underscore the proficiency in manipulating crystallinity within integrated 2D magnetic films on Si wafers, paving the way for large-scale batch manufacturing of practical magnetoelectronic and spintronic devices, heralding a new era of technological innovation.

2D magnetic thin films↗

Polymer Deconstruction and Redesign Strategies for Plastics Recycling

Advancing plastics recycling requires both the selective deconstruction of existing polymers and the design of new materials that enable efficient reuse without loss of performance. This perspective highlights an integrated approach that is rooted in polymer chemistry, catalysis, and process engineering which can enable a circular plastics economy. Here, we outline recent advances in catalytic, solvolytic, and enzymatic pathways for plastic deconstruction, and examine the molecular design principles driving next-generation recyclable-by-design and bio-based polymers. Despite these advances, major knowledge gaps remain in understanding the evolution of polymer morphology and catalyst structure during deconstruction, assessing deconstruction processes with realistic polymers, and offering redesigned polymers with competitive cost and environmental advantage over conventional plastics. United States Department of Energy (U.S. DOE) national laboratories offer unique capabilities to address these challenges through in situ and operando characterization, high-throughput experimentation, environmental studies, technoeconomic and life cycle assessment, scale-up support, and collaboration networks. Advances made in understanding plastic deconstruction mechanisms and structure-property correlations of redesigned polymers inform emerging research directions including autonomous experimentation, real-time feedback-enabled process optimization, and protein engineering for enzymatic depolymerization.

36 MATERIALS SCIENCE↗

A review of artificial intelligence applications in manufacturing operations

Abstract Artificial intelligence (AI) and machine learning (ML) can improve manufacturing efficiency, productivity, and sustainability. However, using AI in manufacturing also presents several challenges, including issues with data acquisition and management, human resources, infrastructure, as well as security risks, trust, and implementation challenges. For example, getting the data needed to train AI models can be difficult for rare events or costly for large datasets that need labeling. AI models can also pose security risks when integrated into industrial control systems. In addition, some industry players may be hesitant to use AI due to a lack of trust or understanding of how it works. Despite these challenges, AI has the potential to be extremely helpful in manufacturing, particularly in applications such as predictive maintenance, quality assurance, and process optimization. It is important to consider the specific needs and capabilities of each manufacturing scenario when deciding whether and how to use AI in manufacturing. This review identifies current developments, challenges, and future directions in AI/ML relevant to manufacturing, with the goal of improving understanding of AI/ML technologies available for solving manufacturing problems, providing decision‐support for prioritizing and selecting appropriate AI/ML technologies, and identifying areas where further research can yield transformational returns for the industry. Early experience suggests that AI/ML can have significant cost and efficiency benefits in manufacturing, especially when combined with the ability to capture enormous amounts of data from manufacturing systems.

Plathottam, Siby Jose↗

Exploiting nonionic surfactants to enhance fatty alcohol production in Rhodosporidium toruloides

Fatty alcohols (FOHs) are important feedstocks in the chemical industry to produce detergents, cosmetics, and lubricants. Microbial production of FOHs has become an attractive alternative to production in plants and animals due to growing energy demands and environmental concerns. However, inhibition of cell growth caused by intracellular FOH accumulation is one major issue that limits FOH titers in microbial hosts. In addition, identification of FOH-specific exporters remains a challenge and previous studies towards this end are limited. To alleviate the toxicity issue, we exploited nonionic surfactants to promote the export of FOHs in Rhodosporidium toruloides, an oleaginous yeast that is considered an attractive next-generation host for the production of fatty acid-derived chemicals. Our results showed FOH export efficiency was dramatically improved and the growth inhibition was alleviated in the presence of small amounts of tergitol and other surfactants. As a result, FOH titers increase by 4.3-fold at bench scale to 352.6 mg/L. With further process optimization in a 2-L bioreactor, the titer was further increased to 1.6 g/L. The method we show here can potentially be applied to other microbial hosts and may facilitate the commercialization of microbial FOH production.

59 BASIC BIOLOGICAL SCIENCES↗

Balancing Doses of EL222 and Light Improves Optogenetic Induction of Protein Production in Komagataella phaffii

ABSTRACT Komagataella phaffii, also known asPichia pastoris, is a powerful host for recombinant protein production, in part due to its exceptionally strong and tightly controlled P AOX1 promoter. MostK. phaffiibioprocesses for recombinant protein production rely on P AOX1 to achieve dynamic control in two‐phase processes. Cells are first grown under conditions that repress P AOX1 (growth phase), followed by methanol‐induced recombinant protein expression (production phase). In this study, we propose a methanol‐free approach for dynamic metabolic control inK. phaffiiusing optogenetics, which can help enhance input tunability and flexibility in process optimization and control. The light‐responsive transcription factor EL222 fromErythrobacter litoralisis used to regulate protein production from the P C120 promoter inK. phaffiiwith blue light. We used two system designs to explore the advantages and disadvantages of coupling or decoupling EL222 integration with that of the gene of interest. We investigate the relationship between EL222 gene copy number and light dosage to improve production efficiency for intracellular and secreted proteins. Experiments in lab‐scale bioreactors demonstrate the feasibility of the outlined optogenetic systems as potential alternatives to conventional methanol‐inducible bioprocesses usingK. phaffii.

Biotechnology & Applied Microbiology↗

Emerging Strategies for Modifying Lignin Chemistry to Enhance Biological Lignin Valorization

Biological lignin valorization represents a promising approach contributing to sustainable and economic biorefineries. Here, the low level of valuable lignin–derived products remains a major challenge hindering the implementation of microbial lignin conversion. Lignin's properties play a significant role in determining the efficiency of lignin bioconversion. To date, despite significant progress in the development of biomass pretreatment, lignin fractionation, and fermentation over the last few decades, little efforts have gone into identifying the ideal lignin substrates for an efficient microbial metabolism. In this Minireview, emerging and state–of–the–art strategies for biomass pretreatment and lignin fractionation are summarized to elaborate their roles in modifying lignin structure for bioconversion. Fermentation strategies aimed at enhancing lignin depolymerization for microbial utilization are systematically reviewed as well. With an improved understanding of the ideal lignin structure elucidated by comprehensive metabolic pathways and/or big data analysis, modifying lignin chemistry could be more directional and effective. Ultimately, together with the progress of fermentation process optimization, biological lignin valorization will become more competitive in biorefineries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improve durability and surface quality of additively manufactured molds using carbon fiber prepreg

Hybrid tooling is an emerging concept introduced in the aerospace industries to reduce weight and cost of traditional tools. A hybrid tool features a skin, which provides desired surface quality, durability, and a low-density substrate to reduce the weight of the mold. The big area additive manufacturing (BAAM) technology permits rapid production of thermoplastic polymer intensive large-scale structures. The present study features a carbon fiber reinforced polyphenylene sulfide (CF-PPS) substrate fabricated using Oak Ridge National Laboratory's BAAM system. Carbon fiber-bismaleimide (CF-BMI) prepreg skin was then bonded to the BAAM tool through high-pressure autoclave molding. Process optimization was conducted to improve the bonding between CF-PPS and CF-BMI (transverse tensile strength increased from 0.54 to 4.8 MPa). Durability of the mold was demonstrated from fabricating seven (7) carbon fiber-Huntsman epoxy hand lay-up parts utilizing the mold.

36 MATERIALS SCIENCE↗

Effects of Cooling Rates on Self-Reinforced Polyethylene Composites via Multiscale Experimental Characterizations

This study investigates cooling rate effects on self-reinforced polyethylene composites (PE-SRCs), focusing on macroscopic thermal and mechanical properties, and micro- to sub-micron morphologies. Unlike conventional fiber-reinforced composites (e.g., carbon and glass fiber based), cooling rate effects on SRCs remain less studied. PE-SRCs were fabricated from ultrahigh molecular weight polyethylene (UHMWPE) fabric and high-density polyethylene (HDPE) matrix with cooling rates from 0.76°C/min to 425°C/min. Tensile properties, including modulus (~9.5 GPa), strength (~360 MPa), and ultimate elongation (~6%), showed no significant cooling rate dependence. However, thermal analysis revealed melting temperature of HDPE matrix decreased from ~130°C to ~126.5°C with total crystallinity reducing from 84% to 75%. Wide-angle X-ray scattering confirmed decreasing crystallinity but at lower values (67%–59%), as thermal analysis might overestimate crystallinity. Small-angle X-ray scattering showed long period decreased from 24.3 to 17.4 nm, attributed to thinner lamellae and closer packing, suggesting limited crystal growth and faster nucleation. While cooling rates alter melting point and crystalline structures of HDPE matrix, these changes do not translate to substantial impact on macroscale mechanical properties of PE-SRCs. This insensitivity might be related to low interfacial shear strength at PE/PE interfaces, enabling process optimization while maintaining mechanical performance.

Cooling rate↗

Characterization of NBCMA—A DAPO Precursor

As part of our investigation into the process optimization of 2,6-diaminopyrazine-1-oxide (DAPO), small-scale sensitivity testing (impact, friction, and ESD) was conducted on the precursor, N-nitroso-bis(cyanomethyl)amine (NBCMA). NBCMA exhibited moderate sensitivity to friction, whereas no sensitivity to impact or spark was observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural Development in Inconel 718 Nickel-Based Superalloy Additively Manufactured by Laser Powder Bed Fusion

Excellent weldability and high temperature stability make Inconel 718 (IN718) one of the most popular alloys to be produced by additive manufacturing. Here in this study, we investigated the effects of laser powder bed fusion (LPBF) parameters on the microstructure and relative density of IN718. The samples were fabricated with independently varied laser power (125 - 350W), laser scan speed (200 - 2200 mm/s), and laser scan rotation (0° - 90°). Archimedes’ method, optical microscopy, and scanning electron microscopy were employed to assess the influence of LPBF parameters on the relative density and microstructure. Optimal processing windows were identified for a wide range of processing parameters and relative density greater than 99.5% was achieved using volumetric energy density between 50 and 100 J/mm3. Microstructural features including melt pool geometry, lack of fusion defect, keyhole porosity, and sub-grain cellular microstructure were examined and quantified to correlate to LPBF parameters. A simple empirical model was postulated to relate relative sample density and LPBF volumetric energy density. Melt pool dimensions were quantitatively measured and compared to estimations based on Rosenthal solution, which yielded a good agreement with the width, but underestimated the depth, particularly at high energy input, due to lack of consideration for keyhole mode. In addition, the sub-grain cellular-dendritic microstructure in the as-built samples was observed to decrease with increasing laser scan speed. Quantification of the sub-micron cellular-dendritic microstructure yielded estimated cooling rate in the order of 10 5 – 10 7 K/s.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Printing polymer blends through in situ active mixing during fused filament fabrication

Fused filament fabrication (FFF) enables production of 3D objects over a range of material compositions at low-cost relative to traditional manufacturing approaches. To date, a limited but growing number of materials are able to be used with FFF, however many applications exist where specific mechanical, thermal, or chemical properties are needed that cannot currently be met with the available feedstock selection. Therefore, a need exists to tune these materials for specific chemical or mechanical properties. One common formulation strategy to address these demanding design parameters is to develop composites or polymer blend filaments. Typically, this is a time-consuming and costly optimization process. Here, we have developed hardware for reproducibly mixing two filaments of similar or dissimilar compositions at the time of printing within individual printed layers. This mixing occurs via software-controlled rotating hardware in the chamber of an extruder’s hot-end. The efficiency of mixing within the printed layers has been characterized in detail as a function of the rotational speed and geometry of the blending hardware. These parameters were exploited to program the ratio and distribution of thermoplastic-based filaments blended within printed extrudate. Example printed specimens were produced with thermoplastic polyurethane (TPU) elastomer blended with rigid polylactic acid (PLA) and Nylon blended with PLA. In addition, a conductive carbon nanotube (CNT)-PLA composite was blended as a function of mixer geometry and input feed ratios with non-conductive PLA and resistance values were measured across the resulting printed specimens.

36 MATERIALS SCIENCE↗

Results of an interlaboratory study on the working curve in vat photopolymerization II: Towards a standardized method

The working curve measurement in photopolymer additive manufacturing is a ubiquitous measure of the cure depth of a printing resin as a function of radiant exposure of light. The fit parameters from this measurement (the depth of light penetration D p and the critical exposure E c ) are used to evaluate and report a resin’s printability, optimize processing parameters, and inform print and resin quality control. Despite its widespread use, the working curve lacks a standard measurement method. Here, following up on our paper “Results of an Interlaboratory Study on the Working Curve in Vat Photopolymerization” from last year, an interlaboratory study on the working curve was performed using calibrated, reproducible, bandpass filtered light sources. With these light sources, the variability between labs in measured working curves was dramatically reduced from the initial interlaboratory study. Aggregate data from this experiment produced reliable D p and E c measurements at 385 nm of 39.2 ± 3.7 µm and 12.3 ± 3.0 mJ cm −2 , respectively. At 405 nm the values of D p and E c are 69.3 ± 3.8 µm and 17.9 ± 2.3 mJ cm −2 , respectively. The results are agnostic to the thickness measurement tool utilized by participants, ensuring broad applicability across laboratories. We also tested the generalizability of the proposed method of using a filtered light source by filtering a commercial 405 nm light source and obtaining a working curve in agreement with the aggregate data from the interlaboratory study. This interlaboratory study provides a basis for a documentary standard for the working curve, so that the entire photopolymer additive manufacturing industry can share reproducible and interoperable working curve data.

36 MATERIALS SCIENCE↗

Hydrocyclone pre-processing of wastewater algae: A strategy for inorganic ash separation

Microalgae cultivation on wastewater can provide remediation and generate valuable feedstocks for biofuel production. Wastewater algae typically have a high percentage of inorganic ash, which can reduce yield and quality of biocrude produced during hydrothermal liquefaction (HTL). Here, in this work, we evaluated the ability of hydrocyclone pre-processing to remove inorganic ash from wastewater algae. The pH of the algae slurry was adjusted to 9.5 to encourage the formation of precipitates and create a density differential between ash particles and algal cells. Hydrocyclone processing successfully concentrated ash particles in the underflow fraction and reduced the total ash percentage in the overflow fraction. Overall, hydrocyclone processing reduced the total ash by 21%, while only 8% of organics were lost. Elemental and mineral analysis showed that Mg and P were concentrated in the underflow in the form of baricite (an isomorph of vivianite). Future research should focus on improving vivianite and/or baricite formation, and therefore ash removal, by providing a reducing environment. The addition of multiple hydrocyclones in series could also improve the removal of ash. We concluded that hydrocyclone treatment of wastewater algae is a feasible method to remove inorganic ash, but further process optimization is required.

09 - BIOMASS FUELS↗

Origins of wear-induced tungsten corrosion defects in semiconductor manufacturing during tungsten chemical mechanical polishing

During chemical mechanical polishing (CMP) process optimization, a unique corrosion defect was identified in the tungsten (W) contact plugs, which were investigated to develop practical solutions to improve CMP mass productivity. The corrosion defect occurred in the absence of external incident energy and was observed to occur only at the W plugs connected to the P + /n-well close to the wafer edge. To examine the root cause of the corrosion, a series of experiments was carried out at each W CMP step, using in-line defect inspection. Additional experiments were conducted using on-line inductively coupled plasma mass spectrometry (ICP-MS) to understand pH- and potential-dependent electrochemical dissolution behaviors of W. Experimentally, W corrosion was confirmed to be exacerbated if the surface oxide of the W plugs is removed by the deionized water (DIW) rinsing step under wafer pressurization, then exposed to DIW and alkaline cleaning solution. Although the DIW rinsing step is commonly performed to clean polishing pads right after the main polishing, a small amount of applied pressure (0.5 psi) without slurry supply can lead to corrosion defects. Finally, this wear-induced corrosion of the W plugs can be prevented by removing the applied pressure during the post DIW rinsing step of W CMP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Defect and satellite characteristics of additive manufacturing metal powders

Metal additive manufacturing (AM) requires high-quality metal powders to three-dimensionally (3D) print metallic components with complex and customizable geometries. The lack of quantification of AM metal powders creates quality control challenges for 3D printed components, increases the uncertainty of printing reliability and net cost of inspected and certified printed components, and reduces the recyclability of used powders. However, critical characteristics of AM metal powders that are decisive factors for the 3D printing process, such as internal porosity, contamination, and satellite feature, remain ambiguous. In this work, we developed a novel approach to 3D quantify key characteristics of AM metal powders down to individual particles by using high-resolution synchrotron x-ray computed tomography. Empowered by the penetrative capability of high-energy x-ray, internal porosity and contamination within as-atomized metal powders from high-entropy alloys to nickel-based superalloys were evaluated. Additionally, the newly-developed dispersion method enables the homogeneous separation of individual particles, and consequently, results in the implementation of 3D particle shape analysis. To resolve a major challenge of identification and quantification of satellite-feature particles in as-atomized AM metal powders, the satellite features were quantitated by modeling and analyzing the shape parameter of local thickness variance. Furthermore, the 3D analytical methods of particle assessment in this study can be applied to other materials systems like rock, food, and pharmaceutical particles, and provide insights for process optimization across powder metallurgy, concrete, food and pharmaceutical manufacturing, and AM industries.

36 MATERIALS SCIENCE↗

Advances and perspectives on mass transfer and enzymatic hydrolysis in the enzyme-mediated lignocellulosic biorefinery: A review

We report enzymatic hydrolysis is a critical process for the cellulase-mediated lignocellulosic biorefinery to produce sugar syrups that can be converted into a whole range of biofuels and biochemicals. Such a process operating at high-solid loadings (i.e., scarcely any free water or roughly ≥ 15% solids, w/w) is considered more economically feasible, as it can generate a high sugar concentration at low operation and capital costs. However, this approach remains restricted and incurs “high-solid effects”, ultimately causing the lower hydrolysis yields with increasing solid loadings. The lack of available water leads to a highly viscous system with impaired mixing that exhibits strong transfer resistance and reaction limitation imposed on enzyme action. Evidently, high-solid enzymatic hydrolysis involves multi-scale mass transfer and multi-phase enzyme reaction, and thus requires a synergistic perspective of transfer and biotransformation to assess the interactions among water, biomass components, and cellulase enzymes. Porous particle characteristics of biomass and its interface properties determine the water form and distribution state surrounding the particles, which are summarized in this review aiming to identify the water-driven multi-scale/multi-phase bioprocesses. Further aided by the cognition of rheological behavior of biomass slurry, solute transfer theories, and enzyme kinetics, the coupling effects of flow-transfer-reaction are revealed under high-solid conditions. Based on the above basic features, this review lucidly explains the causes of high-solid hydrolysis hindrances, highlights the mismatched issues between transfer and reaction, and more importantly, presents the advanced strategies for transfer and reaction enhancements from the viewpoint of process optimization, reactor design, as well as enzyme/auxiliary additive customization.

45 multi-scale, multi-phase, enzymatic reaction↗

Double in-situ lignin modification in surfactant-assisted glycerol organosolv pretreatment of sugarcane bagasse towards efficient enzymatic hydrolysis

Organosolv pretreatment effectively fractionates lignocellulosic biomass for efficient enzymatic hydrolysis, yielding fermentable sugars. However, substantial lignin redeposition on the substrate surface and residual lignin content exacerbate lignin’s inhibitory effects on subsequent enzymatic hydrolysis. Here, an in-situ lignin modification is proposed to address this challenge by incorporating polyethylene glycol (PEG) series into glycerol organosolv (GO) pretreatment. According to the results obtained, PEG-assisted GO pretreated substrate exhibited significantly increased sugar yield during enzymatic hydrolysis, particularly with PEG 4000, showing 35.4% higher glucose yield over 72 h. The improved glucose yield with PEG could be attributed to changes in the physicochemical structure and properties of residual lignin, mitigating its non-productive interaction with cellulase enzymes. PEG's presence in GO pretreatment also increased β-O-4 linkages preservation by 55% and reduced phenolic hydroxyl groups by 28% in lignin fragments versus no surfactants. This outcome resulted from introducing glycerol and PEG hydroxyl tails into the lignin structure, forming α-etherified lignin and rendering it more hydrophilic. Simulations confirmed strong Van Der Waals and hydrogen bonding interactions between lignin units and PEG, hindering lignin fragments repolymerization. Incorporating PEG in the organosolv pretreatment proves highly beneficial for cellulase-mediated lignocellulosic biorefinery, resembling a lignin-first strategy. The optimized process enables efficient biomass utilization for sustainable fuels and chemicals production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Kinetic model development for single step ethanol to butene rich olefin process over Cu-Y/Beta catalysts

Here, this study presents the first intrinsic kinetic model for the single-step conversion of ethanol to butene-rich olefins over bifunctional Cu-Y/Beta catalysts, addressing a critical gap in the design and scale-up of Sustainable Aviation Fuel (SAF) processes. The reaction network comprises ten global steps involving dehydrogenation, aldol condensation, hydrogenation, and dehydration reactions, distributed across Cu and rare-earth (Y) active sites. The model incorporates dual-site functionality (Cu and Y site) and explicitly accounts for key intermediates such as crotonaldehyde and butanal. Reaction rates are formulated using Langmuir–Hinshelwood–Hougen–Watson (LHHW) kinetics. Kinetic parameters are extracted by fitting the model to lab-scale packed-bed reactor data across a wide range of temperatures and space velocities, demonstrating strong agreement in ethanol conversion and product selectivity. The reaction kinetics developed in this work provide a foundational basis for constructing reactor models that enable process optimization and scale-up of ethanol-to-jet fuel technologies.

Cu-Y/Beta catalyst↗