SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Mixtures of alkali metal dawsonite and metal halide show superior performance. In tests of new dry powder fire extinguishants, mixtures of potassium dawsonite with either stannous iodide or potassium iodide found effective for extinguishing jet-fuel fires on hot metal surfaces (up to 900 degrees C). Mixtures performed more effectively than either compound alone.
In the process of reducing extremely fine metal particles (av. particle size or = 1000 angstroms) covered with an oxide layer, the metal particles are fluidized by a gas flow contg. H, heated, and reduced. The method uniformly and easily reduces surface oxide layers of the extremely fine metal particles without causing sintering. The metal particles are useful for magnetic recording materials, conductive paste, powder metallurgy materials, chem. reagents, and catalysts.
Spur gear surface fatigue endurance tests were conducted to investigate hot forged powder metal AISI 4620 and 4640 steel for use as a gear material, to determine endurance characteristics and to compare the results with machined AISI 4340 and 9310 steel gear materials. The as-forged and unground SISI 4620 gear exhibited a 10 percent fatigue life that was approximately one-fourth of that for AISI 9310 and less than one-half that for the AISI 4340 gears. The forged and finish ground AISI 4620 gears exhibited a 10 percent life, approximately 70 percent that of AISI 9310 and slightly better than that of AISI 4340. The AISI 4640 hot forged gears had less fracture toughness and slightly less fatigue life than the AISI 4620 test gears.
Report describes experimental study of thermal responses and aging behaviors of three new aluminum alloys. Alloys produced from rapidly solidified powders and contain 3.20 to 5.15 percent copper, 0.24 to 1.73 percent magnesium, 0.08 to 0.92 percent iron, and smaller amounts of manganese, nickel, titanium, silicon, and zinc. Peak hardness achieved at lower aging temperatures than with standard ingot-metallurgy alloys. Alloys of interest for automobile, aircraft, and aerospace applications.
Process developed to apply necessary insulation to valves, fittings, lines, etc. on such space vehicles as Centaur rocket stage. In new process, electrostatic equipment used to apply powdered polyimide resin directly to part to be insulated.
The reflectance spectra of powdered samples of selected minerals, meteorites, lunar materials and frosts are presented as an aid in the interpretation of present and future remote sensing data of solar system objects. Spectra obtained in separate wavelength regions have been combined and normalized, yielding coverage from 92 to 1800 nm. Spectral features include reflectance maxima in the far UV region produced by valence-conduction interband transitions, and reflectance minima in the near UV, visible and near IR regions, produced by charge transfer and crystal field transitions. Specific maxima and minima are diagnostic of mineral type and composition; additionally, the minerals present in mixtures such as meteorites and lunar samples can be determined.
The equipment used in the experimental measurements of very small black powder propulsion systems is described, giving particular attention to the approach used for the determination of thrust as a function of time. A diagram is shown of the circuit used for the recording of the force. The thrust characteristics of a number of very small propulsion units are considered.
A silicon carbide powder of a 5-micron grain size is mixed with 0.15 to 0.60 wt% mixture of a boron compound, i.e., boric acid, boron carbide (B4C), silicon boride (SiB4 or SiB6), aluminum boride, etc., and an aluminum compound, i.e., aluminum, aluminum oxide, aluminum hydroxide, aluminum carbide, etc., or aluminum boride (AlB2) alone, in such a proportion that the boron/aluminum atomic ratio in the sintered body becomes 0.05 to 0.25 wt% and 0.05 to 0.40 wt%, respectively, together with a carbonaceous additive to supply enough carbon to convert oxygen accompanying raw materials and additives into carbon monoxide.
LARC-TPI, a linear aromatic polyimide, developed by NASA Langley Research Center in the late 1970's had thermoplastic character, but its melt-flow properties were much lower than those of conventional thermoplastics. An imidized version of the LARC-TPI molding powder was submitted to NASA-Langley for evaluation. The initial broad melt of this material occurs in the 270 C range and reorders to higher melting forms, depending on the physical and thermal treatments. Rheological characterization of this polymer shows it to have a very low melt viscosity, which increases as the melted specie transforms to other crystalline forms with higher melting temperatures.
The spectra of samples of several powder and frost materials are presented to serve in a reference database for future far-UV scans of solar system bodies. The spectra cover in the 92-1800 nm wavelengths, i.e., wavenumbers 110,000-5600/cm and photon energies from 13.5-1.5 eV. Preparation procedures for the particulates are delineated. The survey includes feldspars, orthopyroxenes, clinopyroxenes, olivines, assorted minerals, achondrites, carbonaceous chondrites and ordinary chondrites, lunar soils and rocks. Frosts of H2O, CO2, NH3 and SO2 gases were also examined. The data are expected to aid in obtaining spectral matches for asteroids and meteoroids when far-UV telescopy of solar system bodies is performed.
The novel, 'edge-restraint rolling' method has been developed in order to facilitate the thickness reduction of brittle, high strength alloys to the degree of thin plates or sheets, by first hot-compacting the prealloyed powders into billets and conducting the thickness reduction in a series of reheats and roll passes. Attention is presently given to the cases of equiatomic aluminide FeAl, (Ni,Fe)3Al, and an Al-Fe alloy. The flat-rolled products thus obtained may lead to the development of components not otherwise formable for powerplant and other aerospace applications.
Shelf lives of PMR-15 polymides lengthened. Procedure involves quenching of monomer reactions by vacuum drying of PRM-15 resin solutions at 70 to 90 degree F immediately after preparation of solutions. Absence of solvent eliminates formation of higher esters and reduces formation of imides to negligible level. Provides fully-formulated dry PMR-15 resin powder readily dissolvable in solvent at room temperature immediately before use. Resins used in variety of aerospace, aeronautical, and commercial applications.
Rapid-solidification processing yields alloys with improved properties. Study undertaken to extend favorable property combinations of I/M 2XXX alloys through recently developed technique of rapid-solidification processing using powder metallurgy(P/M). Rapid-solidification processing involves impingement of molten metal stream onto rapidly-spinning chill block or through gas medium using gas atomization technique.
Spur gear surface fatigue endurance tests were conducted to investigate hot forged powder metal AISI 4620 and 4640 steel for use as a gear material, to determine endurance characteristics and to compare the results with machined AISI 4340 and 9310 steel gear materials. The as-forged and unground AISI 4620 gear exhibited a 10 percent fatigue life that was approximately one-fourth of that for AISI 9310 and less than one-half that for the AISI 4340 gears. The forged and finish ground AISI 4620 gears exhibited a 10 percent life, approximately 70 percent that of AISI 9310 and slightly better than that of AISI 4340. The AISI 4640 hot forged gears had less fracture toughness and slightly less fatigue life than the AISI 4620 test gears.
Traditionally, vacuum melted 440C stainless steel is used for high performance bearings for aerospace cryogenic systems where corrosion due to condensation is a major concern. For the Space Shuttle Main Engine (SSME), however, 440C performance in the high-pressure turbopumps has been marginal. A basic assumption of this study was that powder metallurgy, rather than cast/wrought, processing would provide the finest, most homogeneous bearing alloy structure. Preliminary testing of P/M alloys (hardness, corrosion resistance, wear resistance, fatigue resistance, and fracture toughness) was used to 'de-select' alloys which did perform as well as baseline 440C. Five out of eleven candidate materials (14-4/6V, X-405, MRC-2001, T-440V, and D-5) based on preliminary screening were selected for the actual rolling-sliding five-ball testing. The results of this test were compared with high-performance vacuum-melted M50 bearing steel. The results of the testing indicated outstanding performance of two P/M alloys, X-405 and MRC-2001, which eventually will be further evaluated by full-scale bearing testing.
Quality of specimen enhanced by improved canning process. Method developed for canning specimens for hot isostatic pressing. Specimen placed inside refractory-metal ring, then sandwiched between two refractory-metal face sheets. Assembly placed inside die, then positioned in vacuum hot press. Heated to set temperature at prescribed vacuum to burn off all of binder in specimen. Advantages: powder-metallurgy composite totally purged of binder sealed in can in single operation, maintains size, shape, and uniformity of specimen. Weld region does not recrystallize, and little possibility of cracking.
The combustion of compact samples was studied; the mechanism of autoignition is defined. Several studies are made of the combustibility of titanium using 50 samples. The data provide a clear idea of the combustibility of titanium powders.
Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.