Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nuclear Fuel Performance Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Development of a Representative Molten Chloride Fast Reactor Model to Assess the Impact of Nuclear Data

The SCALE code system was employed to conduct a preliminary investigation of nuclear data impacts for a fast spectrum molten chloride salt reactor. A computationally effective depletion model that is representative of the reactor system was successfully developed and used to conduct fuel depletion simulations. Development of this model draws from the SLICE method that was developed at Oak Ridge National Laboratory to enable generation of fuel compositions for an advanced reactor core at equilibrium operation. Eigenvalue uncertainty calculations using the ENDF/B-VII.1 nuclear data library were performed for the reactor in the fresh fuel state and an irradiated fuel state. It was determined that the primary driver of eigenvalue uncertainty was the uncertainty in the 235U (n, 𝛾) cross section. Uncertainty calculation results from this study were compared to results available for a different fast system, a sodium-cooled fast reactor, to confirm similarities and identify differences with respect to nuclear data impacts between the two fast advanced reactor systems.

Hirji, Rakim [Georgia Institute of Technology]↗
DOE OSTI2026

X501 Experiment Simulation and PIE Data Comparison

Fuel performance simulations have been developed for X501 MA bearing fuel in BISON. The results of these simulations are compared with PIE results to assess the applicability of metallic fuel models in BISON to MA bearing metallic fuel.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

An IIPG-based finite element framework in MOOSE for modeling fiber reinforced composite failure governed by extrinsic cohesive laws

Fiber reinforced composites (FRC) are widely applied to many important engineering structures such as silicon carbide ceramic matrix composite (SiC CMC) of nuclear fuel claddings. Many material and structure failures are initiated at the interface between two distinctive materials, such as the debonding of interfaces of matrix/fiber of composites or bulk matrix/inclusion in metals at micro-scales. Accurate and robust modeling of these interface failures is critical to the development of novel material and structure with improved functionality. This paper presents a discontinuous Galerkin (DG) finite element method based on the Incomplete Interior Penalty scheme and its implementation in MOOSE for modeling material interface behaviors. The proposed method naturally accommodates important extrinsic cohesive zone material models and is capable of modeling the failures of material interfaces across which material properties are highly distinctive. We demonstrate a good performance of the proposed method using single fiber and multiple fiber debonding problems.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

General overview of multiphysics modeling and simulation at CEA/DES/IRESNE supporting safety, operating and development of nuclear reactors and facilities

This paper presents a general overview of the innovative multiphysics research/development activities carried on by the CEA/DES/IRESNE institute. Eight main different multiphysics fields addressed by IRESNE have been listed (among others: fuel fabrication, behavior of fuels, of reactors, of corium, radionuclide transfer to environment,...) in relation with the involved coupled physics: neutron transport, fluid mechanics, electro-magnetism, heat transfer, solid mechanics and (physico-)chemistry. The major mission of IRESNE institute is to study current and future nuclear systems integrated into a low carbon energy system. To fulfill this mission, IRESNE's activities rely on the development and the implementation of multiphysics modeling, advanced coupling scheme, data transfer techniques and dedicated multiphysics experimentations. Indeed, such multiphysics simulation approach of nuclear systems is today required to deal with the complex intrinsic features of studied phenomena. This approach aims at taking into account physical phenomena interactions, at each interest modeling scale, in order to reach an accurate and predictive behavior representation of a system component or of the whole system. The final objective is to contribute to the development of digital reactor, core and fuel at CEA, by progressing on applied mathematics, high-performance computing and physical mechanism understanding.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Modeling Non-UO2 Fuel With UNF-ST&DARDS

The U.S. Department of Energy’s Used Nuclear Fuel-Storage, Transportation & Disposal Analysis Resource and Data System (UNF-ST&DARDS) provides an easy-to-use interface to analyze irradiated UO2 fuel by allowing all analysis to be performed within the software and being able to store and use dozens of fuel assembly, canister, and cask designs [1]. However, performing these same analyses with non-UO2 fuel, such as UN or U3Si2, requires more user intervention in the process. This work uses UN, UN-ZrO2, and U3Si2 fuel to demonstrate how to perform criticality analyses in the current versions of UNF-ST&DARDS and how a non-UO2 fuel will compare to UO2. This work is part of a larger effort that also includes shielding and thermal analyses, but they will not be discussed.

Ivanusa, Pavlo↗
DOE OSTI2023

Transport Modeling of As-Run ATR Cycles to Support U-10Mo Research Reactor Fuel Qualification Experiment

The Department of Energy’s (DOE) Office of Materials Management and Minimization has been tasked with converting the five remaining United States High Performance Research Reactors (U.S. HPRR) from highly enriched uranium to low-enriched uranium. The Nuclear Regulatory Commission (NRC) regulates Massachusetts Institute of Technology Reactor (MITR), Missouri University Research Reactor (MURR), and National Bureau of Standards Reactor (NBSR); and DOE regulates the High Flux Isotope Reactor and Advanced Test Reactor (ATR). To meet the high demands of these reactors, the U.S. HPRR program has chosen to use 90% uranium - 10% molybdenum (U-10Mo) monolithic fuel. This plate-type fuel will undergo multiple irradiation experiment campaigns in ATR, from mini-plates to full element tests, over a large range of operating conditions. This will provide data in support of the fuel qualification of each reactor. This summary focuses on the as-run neutronic analysis of the first series of mini-plate (MP-1) experiments, which have been irradiated in the ATR. MP-1 experiment’s main goal is to demonstrate the fabrication process and meet the fuel irradiation performance requirements with primary focus on the fuel plates associated with the three NRC reactors, with a small focus on the low power requirements of the ATR fuel. The MP-1 experiments are planned to be the basis of the monolithic U-10Mo fuel for qualification through the NRC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessment of CTF for Steady-state and Transient Post-CHF Conditions in Support of Time-at-Temperature Modeling Applications

The US nuclear industry is exploring options to improve operational economics and uprate the current fleet of light-water reactors by investigating transitioning to cladding performance–based safety criteria as opposed to the current limit, which requires complete avoidance of critical heat flux (CHF)/dryout. Past experience has shown that not all events leading to a dryout are severe enough to cause fuel performance degradation. Allowing temporary dryout of the fuel—that is, using a time-at-temperature (TaT) strategy—could allow for economic improvements via large power uprates and enhanced operational flexibility for current plants without compromising fuel integrity. To support this effort, the US Department of Energy is executing a comprehensive program that includes generating cladding material data under TaT conditions, developing new mechanistic models, and demonstrating modeling and simulation capabilities for transients of interest. This paper presents work performed to assess the CTF thermal-hydraulics subchannel code. CTF is a package used in the VERA core simulator, which will ultimately be used for TaT analysis. CTF will provide the thermal-hydraulic boundary conditions that will be needed for fuel performance analysis in the BISON code. Quantifying both the accuracy and uncertainty of post-CHF models will therefore be necessary. This paper outlines the strategy for the assessment of TaT and presents the results of using the steady-state and transient dryout experiments of the Boiling Fine-mesh Bundle Tests for CTF validation. The results show that the current model tends to overpredict steady-state critical power. This behavior translates to the transient tests, in which CTF is unable to capture transient dryout behavior. Some discussion of sensitivity analysis work being performed is provided to indicate which models must be further analyzed to properly model transient dryout and its uncertainty.

Salko Jr, Robert [ORNL] (ORCID:0000000253566679)↗
DOE OSTI2023

Gas-Cooled High-Temperature Pebble-Bed Reactor Reference Plant Model

This report details a fully coupled neutronics thermal hydraulics reference plant model for a gas-cooled high-temperature pebble-bed reactor. The multiphysics model is developed on the Nuclear Regulatory Commission's Comprehensive Reactor Analysis Bundle (BlueCRAB) available on the Idaho National Laboratory high performance computer, which natively and seamlessly couples Griffin, Pronghorn, and the BISON MOOSE-based applications. Griffin provides the reactor physics capabilities including depletion to the equilibrium core, k-eigenvalue, adjoint, and transient solutions. Pronghorn solves the porous medium equations for the fluid regions and conduction in the solid regions. BISON solves thermal conduction problems for the average pebble and TRISO in the pebble-bed core thus providing the fuel and moderator spatial fields for each pebble burnup group. The neutronics feedback relies primarily on fuel and moderator temperatures. We present results for the coupled steady state equilibrium core and a protected loss of flow event. Although this model is to be considered prototypical with regard to the capabilities in BlueCRAB, its results are consistent with published work by the Institute of Nuclear and New Energy Technology (INET) in China and other research entities.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Accuracy Enhancement of Nuclear Power Plant Simulators Utilizing High Accuracy Simulation Predictions

More recently, reactor core simulators for core designs associated with commercial nuclear power plants that utilize what is believed to be higher fidelity models have been developed. Features such as neutronics models that utilize transport equation solvers with fine spatial meshes and many energy-groups, thermal-hydraulic models that utilize sub-channel solvers with fine spatial mesh and capable of treating a wide range of fluid conditions, and fuel-coolant chemistry interaction models capable of treating CRUD deposition are to be found in these higher fidelity core simulators. These reactor core simulators require access to higher performance computers, characterized by many processors, cores and large memory. So associated with utilization of these simulators is access to high performance computers and ability to accommodate in one’s workflow longer execution times. By contrast, currently used core simulators by the nuclear industry can execute on engineering workstations and have execution times of seconds to minutes. The desirability for having short execution times is not only desired for support of time critical tasks but supports the mental process of decision making by engineers. The goal of the work reported upon here has the objective of retaining the fidelity of higher fidelity models while retaining the ability to utilize engineering workstations. Beyond the core simulator goal, additional goals of this work include incorporating the just described core simulator capability into a Nuclear Steam Supply System (NSSS) simulator, and to incorporate the resulting capability into an environment supportive of design and operational decision making associated with nuclear power stations. The model selected for the core neutronics model is the NESTLE code, for the core thermal-hydraulic model is the CTF code utilizing coarse mesh, and for the NSSS model is the RELAP5-3D code. WSC’s proprietary 3KEYMASTERTM platform is being used to provide software coupling, user interface, visualization, and reporting. The NESTLE core neutronics simulator was first integrated with the CTF core thermal-hydraulic simulator using CTF developed communication commands which are also used for CTF to communicate with RELAP5-3D under WSC’s proprietary 3KEYMASTERTM platform. To assure NESTLE prediction consistency with higher fidelity core neutronic simulators, buffer codes have been created to automatically generate from output files written by the VERA core simulator the NESTLE nodal neutronic parameter’ library, geometry, and pin-power reconstruction input files, thereby avoiding a number of challenges associated with utilizing lattice physics codes and providing consistency with VERA predictions. To treat absorber rod effects a multi-set library is utilized, where a set refers to a specific absorber rod fully inserted pattern. A coarse spatial mesh CTF model was developed with features added that support using CTF as envisioned in the engineering quality simulator. A hybrid meshing approach was implemented to allow for automated construction of models with mixed levels of refinement. Specifically, a core model could resolve some assemblies at a nodal level (4 subchannels per assembly) and others at a pin-resolution (one subchannel per coolant subchannel in the assembly). The intention is that this will allow for better resolution of limiting conditions such as DNBR and PCT, which are based on local rod and subchannel conditions. Further development was done of features that enhance the capabilities for the envisioned engineering quality simulator that has been developed, but now for RELAP-3D. The RELAP5-3D code development includes ability to model more than 999 components and the addition of the cross-channels turbulence mixing model and the void drift model that are implemented in CTF, aiming to achieve closer prediction agreement of the two codes for transient simulations, specifically, more accurate matches of the overall mass, momentum, and energy exchanges of both the liquid and gas phases between the neighboring core assemblies. Graphics were also developed for the Instructor Station for this project under WSC’s proprietary 3KEYMASTERTM platform to facilitate design and operational decision making.

42 ENGINEERING↗
DOE OSTI2021

Modeling 233 Pa Generation in Thorium-fueled Reactors for Safeguards

Thorium has been considered as a possible alternative to uranium for nuclear fuel for many decades. It is three to four times more abundant in the earth than uranium and produces significantly less long-lived transuranic nuclear waste. Some claim thorium poses fewer proliferation concerns than other fuel types largely due to 232 U buildup (and associated high energy gamma-emitting decay products) in the irradiated thorium fuel. However, to fully explore potential proliferation concerns, generation and subsequent decay of 233 Pa produced in the reactor core still must be studied. With its half-life of 27 days, 233 Pa decays to 233 U, which is an International Atomic Energy Agency (IAEA) defined special fissionable material that can be used for nuclear weapons production. With more research being dedicated to thorium-fueled reactors, and several of these reactor designs possessing online fuel processing (allowing for on-site protactinium separation), it is important to understand this potential proliferation pathway. In particular, it is theoretically possible to extract protactinium from the irradiated fuel salt before it decays into 233 U. This hypothetical potential diversion can become an even greater proliferation concern if the extracted protactinium is purified through a second separation of protactinium approximately ten days later to remove the short half-life decay products of 232 Pa and 234 Pa, thus resulting in a higher concentration of the 233 Pa isotope, which decays into weapons usable 233 U with hardly any 232 U or 234 U in it. To estimate the concern of this potential proliferation challenge of thorium, different nuclear material accountancy techniques were reviewed for their viability to quantify 233 Pa if extracted from used thorium fuel. Characteristics of interest included technology maturity, cost, precision, and time taken to acquire results. Some technologies, like hybrid K-edge densitometry and passive gamma spectroscopy, appear to be viable techniques based on current literature. Due to the limited scope of this project, only passive gamma spectroscopy was further investigated. Three different reactor types (PWR, CANDU, MSR) were modeled with mixed thorium-uranium oxide fuels that were burned until the fuel was spent. The protactinium in the used fuel was extracted at the time of shutdown and the change in isotopic content of the protactinium quantified. Gamma spectroscopy simulations were performed for the protactinium isotopes and their decay products at various decay times. Given the simplicity of the models and large assumptions made (e.g. no background, no shielding, no self-attenuation), the initial results indicate that though 233 Pa is detectible for all the reactor types modeled at all decay times (0 to 300 days), more work should be done with higher fidelity models.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2022

Atomistic and cluster dynamics modeling of fission gas (Xe) diffusivity in TRISO fuel kernels

TRISO fuel particles are candidates for use in next generation reactors including gas reactors, fluoride salt-cooled high temperature reactors, and micro-reactors. The UCO fuel kernel consists of a uranium dioxide (UO) and uranium carbide mixture. The addition of UC helps suppress the formation of carbon monoxide gas, which led to failures during initial TRISO development. The addition of uranium carbide alters the chemistry of the UO kernel, which is known to influence performance parameters such as fission gas diffusivity, although the impact has not been quantified and no models exist that take the change in chemistry into account. Therefore, better understanding and more accurate models of the impact of chemistry on fuel performance are of high priority. In this paper, a first-principles density functional theory (DFT) and empirical potential based multi-scale study has been carried out to model the diffusivity of fission gas xenon (Xe) in UCO TRISO fuel kernels. The focus is on the UO component in the UCO fuel kernels, as that represents the largest volume fraction of the fuel kernels. The study relies on DFT and empirical potential calculations to determine Xe and point defect properties, which are then used in thermodynamic and kinetic models to predict diffusion for intrinsic conditions. In addition, the information is utilized in cluster dynamics simulations using the Centipede code to estimate the impact of irradiation on defect transport. Additionally, the presence of UC or UC in the UCO fuel kernels is shown to have a substantial impact on the UO non-stoichiometry by inducing oxygen vacancies and driving UO sub-stoichiometric, which causes much slower Xe diffusion in UCO compared to light water reactor UO fuel. The application of this model in fuel performance simulations using the Bison code is also demonstrated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Development and application of sorption mass transfer models for fission product transport in TRISO fuel systems using BISON

Fission product mass transfer within and between TRISO particle and compact layers is an important phenomenon. It directly impacts fission product release predictions, which are used as source terms for safety and licensing calculations. Modeling fission product transport within layers and across bonded interfaces is relatively straightforward under the assumptions of isotropic Fickian diffusion, concentration continuity, and flux continuity. Modeling fission product transport across gaps and debonded layers is more difficult. Gaps are known to form between the buffer and inner PyC (IPyC), and debonding may occur between the IPyC and silicon carbide (SiC). A new mass transfer model was developed to provide a more accurate and robust fission product release calculation by accounting for interlayer sorptivity. One importance of the new model is to account for temperature and material changes across the gap based on sorption isotherm. This work presents the development of the sorption behavioral model and a fission product trapping model, and analyses the subsequent fission product diffusion behavior, specifically cesium, through TRISO particles and compact materials using the BISON fuel performance code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Machine learning models for volumetric swelling in uranium nitride

Machine learning methods are applied to predict the volumetric swelling rate of the nuclear fuel uranium nitride (UN) over various temperatures, irradiation conditions, and power densities. Both kernel-based methods and symbolic regression models for UN swelling are developed and compared with multiple experimental datasets. We find that the UN pellet geometry and dimensions must be taken into account to accurately model swelling behavior. Strong agreement is observed between the developed machine learning models and the data. The predictive error generated by the machine learning models improves on empirical models taken from the literature. Sensitivity analysis is performed to determine which properties such as temperature, burnup, and power density, are most important in the swelling process. We find that machine learning can be used to quickly develop accurate swelling models for nuclear materials. In conclusion, the presented results illustrate the potential of machine learning to determine volumetric swelling in UN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Design Report on the MiniFuel Instrumented Test Apparatus for Understanding Radiation Effects

Most nuclear fuels irradiations at Oak Ridge National Laboratory (ORNL) over the past decade have been conducted using MiniFuel—a static capsule design employing subscale fuel specimens to collect separate-effects irradiated fuel performance data. Irradiation conditions for MiniFuel experiments are predicted pre-test using reactor physics, and thermal models are verified post-irradiation via SiC dilatometry and various spectrometry methods. Relevant fuel performance parameters are also observed post-irradiation in a hot cell, thereby providing a single data point for each parameter representing the cumulative effects of the irradiation conditions. Substantially more data can be harvested from a single test and within a shorter duration by instrumenting irradiation vehicles and measuring desired quantities in situ. This report presents the design and analysis of the MiniFuel INstrumented Irradiation Test Apparatus for Understanding Radiation Effects (MINITAURE)—an instrumented test rig based on the separate-effects MiniFuel concept that aims to capture fission gas release (FGR) and thermal conductivity degradation of fuel specimens during irradiation in the High Flux Isotope Reactor (HFIR). MINITAURE will be integrated with the Materials Irradiation Facility (MIF) located in the HFIR building outside the reactor containment. The MIF will act as the instrumentation and control center for the experiment, enabling real-time feedback from in situ sensors and control of irradiation temperatures via a gas delivery system. Two unique capsule designs were developed to capture each phenomenon: the thermal conductivity capsule, which uses a thermopile method to estimate fuel specimen thermal conductivity, and the fission gas release capsule, which will have continuous flowing gas communication to high-purity germanium detectors that are housed in the MIF for monitoring FGR. This report details the reactor physics and heat transfer modeling activities that were used to inform the experiment design and predict capsule performance. It also describes out-of-pile activities conducted to stand up this new capability and verify the measurement techniques. Modeling efforts to date have demonstrated the feasibility of the in situ measurement techniques and supported the development of the MINITAURE assembly configuration. Out-of-pile testing of the thermal conductivity measurement shows promise in capturing relative changes in thermal conductivity. However, significant errors exist in the measured absolute value, posing a need for further refinement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Conjugate Heat Transfer Modeling of Salt-Filled Fuel Pins for Stable Salt Reactor Safety Analysis

The Stable Salt Reactor (SSR) combines the proven structural design of light water reactor fuel assemblies with the inherent safety and fuel-cycle advantages of molten salt technology. In its fast reactor configuration, the SSR utilizes recycled nuclear waste as fuel, sealed within narrow salt-filled fuel pins and cooled by a surrounding liquid salt coolant. Reliable transfer of heat from the molten fuel salt through the cladding to the external coolant is essential for both reactor safety and performance. This work investigates conjugate heat transfer (CHT) in the SSR’s salt-filled fuel pins using NekRS, a high-fidelity spectral element computational fluid dynamics (CFD) solver. The analyses capture internal natural convection within the molten fuel salt and external forced convection in the coolant, under steady-state and transient operating conditions. Parametric studies evaluate how variations in reactor power and coolant flow rate influence heat transfer distributions and system response. The high-fidelity CFD results are time-averaged and post-processed for direct comparison with moderate-fidelity Reynolds-averaged Navier–Stokes (RANS) models, and for the development of reduced-order models within the SAM system code. These validated models support fast-running safety analyses of normal and off-normal transients, improving predictive capability for key safety margins. By integrating advanced CFD with system-level safety tools, this study strengthens the modeling framework for SSR design, reduces uncertainty in molten salt CHT simulations, and accelerates the engineering and licensing of next-generation nuclear reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Empirical and mechanistic transient fission gas release model for high-burnup LOCA conditions

In response to the nuclear industry desire to extend burnup beyond current licensing practices, the US Nuclear Regulatory Commission (NRC) released a research information letter (RIL) that provides a basis for analyzing fuel fragmentation, relocation, and dispersal (FFRD) in light-water reactors. Of the five elements discussed, the most ambiguous is the significance of transient fission gas (FG) release (FGR) (tFGR) and its effects on fuel performance under loss-of-coolant accident conditions. In fresh fuel, FG migration and eventual release is primarily governed by diffusion-based mechanisms at higher temperatures (>1,000 °C). However, the mechanisms governing FGR changes as burnup increases. More recent research indicates that FGR increases as burnup increases, specifically under temperature transient conditions, and this release occurs at lower temperatures with a new release mechanism. This behavior has been attributed to microcracking in the fuel and is likely related to microstructure embrittlement with the presence of over pressurized FG bubbles. The NRC RIL outlines the complexity of the phenomenon and a need for a deeper understanding to adequately address FFRD for regulatory application. Here, therefore, this manuscript intends to summarize the publicly available tFGR data and discuss the observed dependencies (e.g., burnup, heating rate, sample geometry, terminal temperature). An empirical model has been developed and benchmarked against recently published experimental data. However, this empirical model is limited to conditions for which fitting data exist and, therefore, a high-level discussion is included to provide a roadmap for atomistically-informed multiscale modeling in conjunction with experimental data collection to develop a mechanistic tFGR model widely applicable to a broad range of nuclear fuel conditions at high burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

MORPHOLOGICAL AND RADIATION DAMAGE INFORMED THERMAL PROPERTY PREDICTION IN SCALED GEOMETRIC DOMAINS

This proposed work has the potential to rewrite the way the nuclear industry investigates new fuel and nuclear material designs. The current rubric of nuclear material design has myriad steps in the process, and while certain physics are modeled accurately, each step must be connected in order to obtain an entire description of the process. At present, neutronic, thermal, microstructural, fission product chemistry and migration, and radiation defect analysis (hereafter referred to together as “combined analysis”) are performed, albeit separately. There is no existing method which combines these physics in an attempt to understand the natural interactions between these phenomena. Consequently, the timeline for design, fabrication, experiment, validation, and licensing can take years. A disruptive approach is required to accelerate the development of new technology. This proposed undertaking creates a validated computational framework, generating a new microscopic-to-macroscopic methodology yielding thermal property predictions for nuclear fuels and materials at an engineering spatial scale.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

BISON Simulation Development for ALD Coated Particles (Progress Report, FY21)

Argonne has on ongoing effort to perform atomic layer deposition coatings on micron-scale fuel particles. Initial results showed cracking of the coating layer above a specific coating thickness, which motived the development of a BISON model for the coated particle system to help explain the behavior. This report describes the initial development of the BISON model, the materials models used, and the conditions used in the simulation. A 2D model has been developed, with sensitivity studies performed on several key parameters. Based on the 2D model results, and 3D model was also developed, with results from all calculations described. First principles calculations were also performed on the fuel/coating interface to help describe the observed behavior. Potential future activities are also described.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗