The change of thermal properties and microstructure on an AM fabricated AlSi10Mg alloy during thermal annealing.
Abstract not provided.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided.
Microstructure and mechanical properties at 25–1200 °C of new refractory alloys, Nb-18Ti-12W (NTW), Nb-18Ti-12W-5Re (NTW-R) and Nb-18Ti-12W-5Re-1Al (NTW-RA), all compositions are in atomic percent, are reported. The alloys are developed as an alternative to a denser, more expensive and difficult-to-process refractory alloy WC-3009. After production by arc melting and hot isostatic pressing at 1400 °C, 207 MPa for 3 h, the alloys have a BCC crystal structure with the average grain size of ~150–200 μm and contain low volume fraction of (Ti,N)-rich precipitates near grain boundaries. NTW shows excellent malleability at all studied temperatures. Its yield stress at 25 °C, 1000 °C and 1200 °C is 874 MPa, 353 MPa and 202 MPa, respectively. The NTW-R and NTW-RA alloys are stronger at all the studied temperatures; however, they lack in compression ductility at 25 °C. As a result, extensive deformation twinning and formation of intergranular voids precede the fracture of these two alloys at 25 °C.
Explore the source record for details and available documents.
Here, the goal of this work was to understand the effects of aging at 800 °C on the microstructures and mechanical properties of two recently-developed AFA stainless steels based on Fe-14Cr-32Ni-3Nb-3Al-2Ti (wt.%), one of which contained small additions of boron and carbon. To that end both the size distributions and growth kinetics of the B2, Laves phase, L1 2 precipitates present were quantified. While the lattice parameter, morphology, size and coarsening behavior of the L1 2 precipitates was the same in both AFA alloys, the B and C enhanced the grain boundary coverage by both Laves phase and B2-NiAl precipitates, but suppressed their coarsening. These interstitial additions also suppressed the formation of twins and discontinuous precipitation, which were observed in the B and C-free material. It is shown that the yield strength at 700 °C is largely controlled by the size of the L1 2 precipitates, with the largest strengthening effect obtained after aging for 2.4 h for both AFA alloys. Longer aging time led to a loss of strength mainly due to the coarsening of the L1 2 precipitates.
This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.
The optical and morphological properties of reactively sputtered AlN films on Si substrates have been studied in this work from a self-consistent three-layer optical model developed from spectroscopic-ellipsometry analysis and validated by observations from transmission-electron microscopy, Auger electron spectroscopy, and in situ reflectance interferometry. These properties correlate to the film microstructural properties. Accordingly, the almost thickness-independent refractive index of 2.01 of the bulk AlN layer indicates its polycrystalline microstructure. This layer also appears ungraded, homogeneous, isotropic, and free of excess Al, as if grown through a steady process. The small film absorption points to the Urbach tail states produced by the structural disorder typical of such sputtered films. The films' interface layer consists of a graded Bruggeman intermix of outdiffused Si and AlN materials spreading over 10-12 nm thickness. The surface morphology includes an Al{sub 2}O{sub 3}-oxidized outer rough surface gradually becoming AlN bulk with diminishing amounts of Al{sub 2}O{sub 3} and inner pores. The increase in the surface-layer thickness, as the film grows, indicates further surface roughening due to enlarging crystals in a disoriented growth. This spectroscopic-ellipsometry analysis of AlN films has allowed us to study the effect of substrate biasing on the AlN microstructure and to place forward a new processing method for the surface smoothening of rough AlN and diamond films.
The morphology and microstructure of columnar niobium oxide nanostructures are studied and the dependences of their morphological sizes on anodizing voltages (100–450 V) and anodic alumina pore diameters (40–150 nm) are established. The features of ion transport during local anodization of niobium are studied and the transport numbers of electrolyte anions and niobium cations are calculated; a mechanism of formation and growth is proposed and the phase composition and electrophysical properties of columnar nanostructures are studied.
In order to achieve energy conversion efficiencies of > 50 pct for steam turbines/boilers in power generation systems, materials are required that are both strong and corrosion-resistant at > 973 K (700 A degrees C), and economically viable. Austenitic steels strengthened with Laves phase, NiAl and Ni3Al precipitates, and alloyed with aluminum to improve oxidation resistance, are potential candidate materials for these applications. The microstructure and microchemistry of recently developed alumina-forming austenitic stainless steels have been characterized by scanning electron microscopy, transmission electron microscopy, and synchrotron X-ray diffraction. Different thermo-mechanical treatments were performed on these steels to improve their mechanical performance. These reduced the grain size significantly to the nanoscale (similar to 100 nm) and the room temperature yield strength to above 1000 MPa. A solutionizing anneal at 1473 K (1200 A degrees C) was found to be effective for uniformly redistributing the Laves phase precipitates that form upon casting. (C) The Minerals, Metals & Materials Society and ASM International 2015
The microstructure and thermoelectric properties of the PbTe-Si eutectic system are presented in detail. When rapidly quenched from the melt this system yields materials with thermoelectric properties similar to PbTe itself but with improved mechanical properties. Doping optimization was performed using PbI{sub 2} as an n-type dopant giving precise control of the thermoelectric properties. Electron microscopy indicates that the PbTe-Si system is both a nanocomposite and microcomposite. Despite the added Si, the thermal conductivity of this composite follows closely that of PbTe. The temperature dependence of the Lorenz number was estimated, and it shows a significant departure from the value of metals (L{sub 0}) reaching only 45% of L{sub 0} at 650 K. The optimized ZT for the PbTe-Si(8%) eutectic was 0.9 at 675 K. The improved mechanical robustness of these composites makes them attractive for use in large scale thermoelectric device fabrication.
The microstructure and nanomechanical properties of three samples of the modified stainless steel (referred as the alloy D9) were systematically characterized after neutron irradiation in the Advanced Test Reactor. The samples were irradiated to 5.0, 8.2, and 9.2 displacements per atom at 448, 430, and 683°C, respectively. The evolutions of dislocation loops, cavities, and radiation-induced precipitates were quantitatively studied to reveal their dose and temperature dependencies. Nanohardness and nanoindentation creep tests were conducted at room temperature on the irradiated samples. Unexpected radiation hardening was observed in the highest-temperature-irradiated sample due to the formation of an unknown type of Ni- and Si-rich precipitates whose contributions to the radiation and mechanical performances of the alloy were discussed. We provide the radiation-microstructure-property correlations of alloy D9 with new insights, which can benefit the development and optimization of advanced austenitic alloys for future nuclear applications.
Conductive LaNiO{sub 3} (LNO) thin films were deposited on Si substrates by RF sputtering at room temperature to 600 Degree-Sign C. X-ray diffraction of the LNO films showed that preferred orientation varied from (100) below 500 Degree-Sign C to (110) at 600 Degree-Sign C at deposition temperature of 200-600 Degree-Sign C. The room temperature resistivity was 2250-3400 {mu}{Omega}-cm at the range of 200 Degree-Sign C {approx}500 Degree-Sign C. The LNO films, deposited at room temperature, were postannealed in air from 500 to 800 Degree-Sign C, and the resistivity value was 280 {mu}{Omega}-cm at a postannealing temperature of 600 Degree-Sign C. Subsequently, sol-gel derived (Pb,La)(Zr,Ti)O{sub 3} thin films were deposited on LNO-buffered nickel substrates and characterized, the results were compared to those of the same films on silicon substrates. The comparison demonstrated that the performance characteristics of the LNO-buffered nickel foils are similar to those of LNO-buffered silicon substrates. Thus, LNO films prepared by the sputtering method can act as an effective barrier layer on nickel substrates for embedded microelectronic devices.
Highlights: • The microstructure of limestone (25 °C–800 °C) was analyzed by XRD, SEM and TG-DSC. • The microstructural properties of the crystal are anisotropic in different crystal plane directions. • Microstructure controls the macroscopic properties of limestone. - Abstract: Limestone is a common rock used in many buildings and found in underground engineering projects. After exposure to heat, for example, the occurrence of fires, the stability of limestone structures is mostly affected, which may have safety repercussions. Therefore, the impact of thermal effects on the microstructure of limestone is investigated in this study, in which 8 groups of limestone samples are exposed to different temperatures (25 °C, 100 °C, 200 °C, 300 °C, 500 °C, 600 °C, 700 °C and 800 °C), after which X-ray diffraction, differential scanning calorimetry and scanning electron microscopy are carried out. The mineral composition and the microstructure of the samples are numerically modeled, in which the diffraction peaks, full width at half maximum, integral breadth, microstrain, average domain size and dislocation density are analyzed. The macroscopic properties obtained from the results in other works in the literature including porosity, compressive strength, damage coefficients and modulus of elasticity are also compared with the parameters above. The changes in the crystal structure of two minerals, calcite and dolomite, are found to be anisotropic in the different crystal plane directions. It is also found that the limestone microstructure affects the macroscopic properties. A temperature between 200 °C to 300 °C is the critical temperature at which both the macroscopic properties and macrostructure demonstrate significant changes.
The effect of solution heating rate on quasi-static and dynamic mechanical properties of Al-Mg-Si-Cu alloy in bake hardening state was investigated through mechanical properties, microstructure and fracture morphology characterization in the present study. The results show that solution heating rate has a strong influence on microstructure, quasi-static and dynamic mechanical properties. As solution heating rate rises, the grain microstructure transforms from the elongated grains to equiaxed grains and the fraction of low-angle grain boundaries (LAGBs) also decreases. Moreover, the equivalent average grain size first decreases, and then increases. The relationship between solution heating rate and mechanical property is monotonic, not depending on strain rate. As solution heating rate rises, the yield strength, ultimate tensile strength and elongation decrease. In contrast to quasi-static loading, dynamic loading always tends to improve strengths and elongation. In addition, compared with the quasi-static tensile specimens, the dynamic tensile specimens possess a larger number of dislocations. Regardless of strain rate and solution heating rate, all the tensile specimens exhibit the ductile fracture mode. As solution rate rises, the dimples decrease and become shallow gradually. The dimples in dynamic fracture zone are larger and deeper than those in the quasi-static fracture zone.
In this communication, it is aimed to optimize the conditions for T6 heat treatment of permanent die cast Al–Si–Cu–Mg alloys. Various solutionizing temperatures, aging treatments and soaking times were used to improve / modify the mechanical properties of presently studied alloys. Formation mechanism of the particles was understood by carrying out optical microscopy and energy dispersive X–ray (EDX) spectroscopy measurements. Spherical particles of alloys were studied for their microstructural properties using scanning electron microscopy (SEM). Microhardness test was performed to investigate their mechanical properties. Dependence of cluster formation and microhardness of the alloys on the adequate solutionizing temperature, aging treatment and soaking time has been discussed in detail.
Not Available
This report summarizes research activities conducted at Argonne National Laboratory in support of the development, qualification and certification of additively manufactured (AM) metallic components to allow for innovative reactor design and licensing for the Transformational Challenge Reactor (TCR). Focus is on the evaluation of high temperature mechanical properties including creep and fatigue of 316L stainless steel manufactured by the laser powder bed fusion process. Creep behavior of AM 316L stainless steel was evaluated for rods printed by either or a combination of both lasers of the dual-laser system of a Concept Laser-M2 printer to examine the consistency across the build plate. Creep tests were conducted at temperatures of 550, 575, 600, and 650°C and stresses between 175 and 300 MPa using ASTM standard-sized specimens. The effect of heat treatments at different temperatures on creep properties of AM 316L SS was examined to understand the processing-microstructure-property relationship. Fatigue properties of AM 316L SS were investigated for two print geometries (rod and plate) and in two build orientations of printed plates. Locations of specimens in the build were carefully tracked such that the testing data can be directly related to location-specific in situ data to establish links between printing process, post-printing treatment, microstructure and mechanical properties. The work is to support the development of a digital platform informed approach to AM component qualification and certification for nuclear applications.
Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 10 3 to 10 8 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed ‘melt pools’, were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.
Serapis temple, which was constructed in the Roman period in the city of Pergamon (Bergama/Turkey), is one of the most important monuments of the world heritage. In this study, the characteristics of bricks and mortars used in the temple have been determined in order to define the necessary characteristics of the intervention materials, which will be used in the conservation works of the temple. Several analyses were carried out to determine their basic physical properties, raw material compositions, mineralogical and microstructural properties using X-ray diffraction, Scanning Electron Microscope and a Thermo Gravimetric Analyzer. Analysis results indicated that the mortars are stiff, compact and hydraulic due to the use of natural pozzolanic aggregates. The Roman bricks are of low density, high porosity and were produced from raw materials containing calcium poor clays fired at low temperatures.