Results for “Logic Design” — Page 20

NASA NTRS1975

Development of components for an S-band phased array antenna subsystem

The system requirements, module test data, and S-band phased array subsystem test data are discussed. Of the two approaches to achieving antenna gain (mechanically steered reflector or electronically steered phased array), the phased array approach offers the greatest simplicity and lowest cost (size, weight, power, and dollars) for this medium gain. A competitive system design is described as well as hardware evaluation which will lead to timely availability of this technology for implementing such a system. The objectives of the study were: to fabricate and test six engineering model transmit/receive microelectronics modules; to design, fabricate, and test one dc and logic multilayer manifold; and to integrate and test an S-band phased array antenna subsystem composed of antenna elements, seven T/R modules, RF manifolds and dc manifold.

Source record↗

NASA NTRS1979

Space Shuttle communications RF switch matrix

The Shuttle Orbiter communications equipment includes phase modulation (PM) and frequency modulation (FM) channels. The PM section has the capability of routing high levels of energy (175 W) from any one of four transmitters to any one of four antennas, mutually exclusive. The FM channel uses a maximum of 15-W power routed from either of two transmitters to one of two antennas, mutually exclusive. The paper describes the design and the theory of a logic-controlled RF switch matrix devised for the purposes cited. Both PM and FM channels are computer-controlled with manual overrides. The logic interface is realized with CMOS logic for low power consumption and high noise immunity. The interior of the switch matrix is maintained at a pressure of 15 psi (90% nitrogen, 10% helium) by an electron beam-welded encapsulation. The computational results confirm the viability of the RF switch matrix concept.

Winch, R.↗

NASA NTRS1985

Approach for service life extension of explosive devices for aircraft escape systems

Service life extension of explosive devices used in aircraft escape systems can achieve considerable savings. An overall approach is needed to challenge the logic of explosive component service extension from design to removal from service for evaluation. The purpose of the effort described in this paper was to develop a service-extension approach on explosive devices used in aircraft systems, supported by actual testing of representative candidate devices, to evaluate quantitatively the effects of service, age, and degradation, and allow responsible, conservative service life determinations. Evaluated were five explosive components: rigid and flexible explosive transfer lines, one-way transfers, flexible linear shaped charges, and initiation handles. The service extension approach generated in this effort is summarized by eight recommendations.

Bement, L. J.↗

NASA NTRS1988

Avionic expert systems

At the heart of any intelligent flight control system, there is a knowledge based expert system. The efficiency of these knowledge bases is one of the major factors in the success of aviation and space control systems. In the future, the speed and the capabilities of the expert system and their underlying data base(s) will be the limiting factors in the ability to build more accurate real time space controllers. A methodology is proposed for design and construction of such expert systems. It is noted that existing expert systems are inefficient (slow) in dealing with nontrivial real world situations that involve a vast collection of data. However, current data bases, which are fast in handling large amounts of data, cannot carry out intelligent tasks normally expected from an expert system. The system presented provides the power of deduction (reasoning) along with the efficient mechanisms for management of large data bases. In the system, both straight forward evaluation procedures and sophisticated inference mechanisms coexist. The design methodology is based on mathematics and logic, which ensures the correctness of the final product.

Golshani, Forouzan↗

NASA NTRS1989

A programmable CCD driver circuit for multiphase CCD operation

A programmable CCD (charge-coupled device) driver circuit was designed to drive CCDs in multiphased modes. The purpose of the drive electronics is to operate developmental CCD imaging arrays for NASA's tiltable moderate resolution imaging spectrometer (MODIS-T). Five objectives for the driver were considered during its design: (1) the circuit drives CCD electrode voltages between 0 V and +30 V to produce reasonable potential wells, (2) the driving sequence is started with one input signal, (3) the driving sequence is started with one input signal, (4) the circuit allows programming of frame sequences required by arrays of any size, (5) it produces interfacing signals for the CCD and the DTF (detector test facility). Simulation of the driver verified its function with the master clock running up to 10 MHz. This suggests a maximum rate of 400,000 pixels/s. Timing and packaging parameters were verified. The design uses 54 TTL (transistor-transistor logic) chips. Two versions of hardware were fabricated: wirewrap and printed circuit board. Both were verified functionally with a logic analyzer.

Ewin, Audrey J.↗

NASA NTRS1991

Digital Signal Conditioning for Flight Test Instrumentation

This volume in the AGARD Flight Instrumentation Series provides flight test instrumentation engineers with an introduction to digital measurement processes on aircraft. Flight test instrumentation systems are rapidly evolving from analog-intensive to digital-intensive systems, including the use of onboard digital computers. Topics include measurements that are digital in origin, as well as sampling, encoding, transmitting, and storing of data. Particular emphasis is placed on modern avionic data bus architectures and what to be aware of when extracting data from them. Examples of data extraction techniques are given. Tradeoffs between digital logic families, trends in digital development, and design testing techniques are discussed. An introduction to digital filtering is also covered.

Data acquisition↗

NASA NTRS1991

Digital Signal Conditioning for Flight Test, Volume 19 [Le Traitement du Signal Numérique pour les Essais en Vol]

This volume in the AGARD Flight Instrumentation Series provides flight test instrumentation engineers with an introduction to digital processes on aircraft. Flight test instrumentation systems are rapidly evolving from analog intensive to digital intensive systems, including the use of onboard digital computers. Topics include: measurements that are digital in origin, sampling, encoding, transmitting, and storing of data. Particular emphasis is placed on modem avionic data bus architectures and what to be aware of when extracting data from them. Some example data extraction techniques are given. Tradeoffs between digital logic families, trends in digital development, and design testing techniques are discussed. An introduction to digital filtering is also covered.

Flight instruments↗

NASA NTRS1992

Schematic driven layout of Reed Solomon encoders

Two Reed Solomon error correcting encoders are presented. Schematic driven layout tools were used to create the encoder layouts. Special consideration had to be given to the architecture and logic to provide scalability of the encoder designs. Knowledge gained from these projects was used to create a more flexible schematic driven layout system.

Arave, Kari↗

NASA NTRS2001

Electronic Model of a Ferroelectric Field Effect Transistor

A pair of electronic models has been developed of a Ferroelectric Field Effect transistor. These models can be used in standard electrical circuit simulation programs to simulate the main characteristics of the FFET. The models use the Schmitt trigger circuit as a basis for their design. One model uses bipolar junction transistors and one uses MOSFET's. Each model has the main characteristics of the FFET, which are the current hysterisis with different gate voltages and decay of the drain current when the gate voltage is off. The drain current from each model has similar values to an actual FFET that was measured experimentally. T'he input and o Output resistance in the models are also similar to that of the FFET. The models are valid for all frequencies below RF levels. No attempt was made to model the high frequency characteristics of the FFET. Each model can be used to design circuits using FFET's with standard electrical simulation packages. These circuits can be used in designing non-volatile memory circuits and logic circuits and is compatible with all SPICE based circuit analysis programs. The models consist of only standard electrical components, such as BJT's, MOSFET's, diodes, resistors, and capacitors. Each model is compared to the experimental data measured from an actual FFET.

MacLeod, Todd C.↗

NASA NTRS2000

Free Flight Simulation: An Initial Examination of Air-Ground Integration Issues

The concept of "free flight" is intended to emphasize more flexibility for operators in the National Airspace System (RTCA, 1995). This may include the potential for aircraft self-separation. The purpose of this simulation was to begin examining some of the communication and procedural issues associated with self-separation in an integrated air-ground environment. Participants were 10 commercial U.S. flight crews who flew the B747-400 simulator and 10 Denver ARTCC controllers who monitored traffic in an ATC simulation. A prototypic airborne alerting logic and flight deck display features were designed to allow for increased traffic and maneuvering information. Eight different scenarios representing different conflict types were developed. The effects of traffic density (high and low) and different traffic convergence angles (obtuse, acute, and right) were assessed. Conflict detection times were found to be lower for the flight crews in low density compared to high density scenarios. For the controllers, an interaction between density and convergence angle was revealed. Analyses on the controller detection times found longer detection times in the obtuse high density compared to obtuse low density, as well as the shortest detection times in the high density acute angle condition. Maneuvering and communication events are summarized, and a discussion of future research issues is provided.

Lozito, Sandra↗

NASA NTRS2002

Simulation Model of A Ferroelectric Field Effect Transistor

An electronic simulation model has been developed of a ferroelectric field effect transistor (FFET). This model can be used in standard electrical circuit simulation programs to simulate the main characteristics of the FFET. The model uses a previously developed algorithm that incorporates partial polarization as a basis for the design. The model has the main characteristics of the FFET, which are the current hysterisis with different gate voltages and decay of the drain current when the gate voltage is off. The drain current has values matching actual FFET's, which were measured experimentally. The input and output resistance in the model is similar to that of the FFET. The model is valid for all frequencies below RF levels. A variety of different ferroelectric material characteristics can be modeled. The model can be used to design circuits using FFET'S with standard electrical simulation packages. The circuit can be used in designing non-volatile memory circuits and logic circuits and is compatible with all SPICE based circuit analysis programs. The model is a drop in library that integrates seamlessly into a SPICE simulation. A comparison is made between the model and experimental data measured from an actual FFET.

MacLeod, Todd C.↗

NASA NTRSDate not supplied

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRS2024

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRS2006

Systems Integration Processes for NASA Ares I Crew Launch Vehicle

NASA's Exploration Initiative will require development of many new elements to constitute a robust system of systems. New launch vehicles are needed to place cargo and crew in stable Low Earth Orbit (LEO). This paper examines the systems integration processes NASA is utilizing to ensure integration and control of propulsion and nonpropulsion elements within NASA's Crew Launch Vehicle (CLV), now known as the Ares I. The objective of the Ares I is to provide the transportation capabilities to meet the Constellation Program requirements for delivering a Crew Exploration Vehicle (CEV) or other payload to LEO in support of the lunar and Mars missions. The Ares I must successfully provide this capability within cost and schedule, and with an acceptable risk approach. This paper will describe the systems engineering management processes that will be applied to assure Ares I Project success through complete and efficient technical integration. Discussion of technical review and management processes for requirements development and verification, integrated design and analysis, integrated simulation and testing, and the integration of reliability, maintainability and supportability (RMS) into the design will also be included. The Ares I Project is logically divided into elements by the major hardware groupings, and associated management, system engineering, and integration functions. The processes to be described herein are designed to integrate within these Ares I elements and among the other Constellation projects. Also discussed is launch vehicle stack integration (Ares I to CEV, and Ground and Flight Operations integration) throughout the life cycle, including integrated vehicle performance through orbital insertion, recovery of the first stage, and reentry of the upper stage. The processes for decomposing requirements to the elements and ensuring that requirements have been correctly validated, decomposed, and allocated, and that the verification requirements are properly defined to ensure that the system design meets requirements, will be discussed.

Taylor, James L.↗

NASA NTRS1974

A self-reorganizing digital flight control system for aircraft

This paper presents a design method for digital self-reorganizing control systems which is optimally tolerant of failures in aircraft sensors. The functions of this system are accomplished with software instead of the popular and costly technique of hardware duplication. The theoretical development, based on M-ary hypothesis testing, results in a bank of M Kalman filters operating in parallel in the failure detection logic. A moving window of the innovations of each Kalman filter drives the detection logic to decide the failure state of the system. The detection logic also selects the optimal state estimate (for control logic) from the bank of Kalman filters. The design process is applied to the design of a self-reorganizing control system for a current configuration of the space shuttle orbiter at Mach 5 and 120,000 feet. The failure detection capabilities of the system are demonstrated using a real-time simulation of the system with noisy sensors.

Montgomery, R. C.↗

NASA NTRS1993

Neural network applications

A design procedure is suggested for neural networks which accommodates the inclusion of such knowledge-based systems techniques as fuzzy logic and pairwise comparisons. The use of these procedures in the design of applications combines qualitative and quantitative factors with empirical data to yield a model with justifiable design and parameter selection procedures. The procedure is especially relevant to areas of back-propagation neural network design which are highly responsive to the use of precisely recorded expert knowledge.

Padgett, Mary L.↗

NASA NTRS1993

Design issues for a reinforcement-based self-learning fuzzy controller

Fuzzy logic controllers have some often cited advantages over conventional techniques such as PID control: easy implementation, its accommodation to natural language, the ability to cover wider range of operating conditions and others. One major obstacle that hinders its broader application is the lack of a systematic way to develop and modify its rules and as result the creation and modification of fuzzy rules often depends on try-error or pure experimentation. One of the proposed approaches to address this issue is self-learning fuzzy logic controllers (SFLC) that use reinforcement learning techniques to learn the desirability of states and to adjust the consequent part of fuzzy control rules accordingly. Due to the different dynamics of the controlled processes, the performance of self-learning fuzzy controller is highly contingent on the design. The design issue has not received sufficient attention. The issues related to the design of a SFLC for the application to chemical process are discussed and its performance is compared with that of PID and self-tuning fuzzy logic controller.

Yen, John↗