Results for “Linear Solvers” — Page 20

NASA NTRSDate not supplied

Predicting Orion Launch Abort Acoustics

Computational fluid dynamics (CFD) scale-resolving simulations were performed to help assess the Orion launch abort system’s vibro-acoustic environment in collaboration with the Orion Loads and Dynamics team at the Johnson Space Center (JSC). The primary objectives are to establish best practices and to validate CFD predictions for surface fluctuating pressure spectra with ground, wind tunnel, and flight test data. Excellent agreement is obtained between CFD predictions by the Cartesian adaptive mesh refinement (AMR) module of the Launch, Ascent, and Vehicle Aerodynamics (LAVA) solver and measurements from a ground test representative of the start of a pad abort scenario, and with measurements from a wind tunnel test case corresponding to a transonic, high total angle of attack ascent abort scenario. A simplified (static and at rest) simulation of a pad abort flight test shows good agreement with the flight data, whereas a more costly simulation where the vehicle is accelerating relative to the ground from rest to Mach 0.4 shows consistent over-prediction of the spectra. Simulation results for a supersonic ascent abort flight test are in reasonable agreement with the measurements, but show larger excursions in regions where non-linear interactions between the plume turbulence, shocks, and turbulent boundary layer are strongest – likely due to CFD modeling assumptions, the effect of which are discussed. Overall, the CFD results demonstrate that scale-resolving simulation methodologies like the one presented can help characterize full-scale launch abort vehicle near-field noise and can complement wind tunnel, ground and flight tests by providing trends and reducing uncertainty for scenarios that cannot or are not planned to be tested.

Orion↗

NASA NTRS1993

Development of an explicit multiblock/multigrid flow solver for viscous flows in complex geometries

A new computer program is being developed for doing accurate simulations of compressible viscous flows in complex geometries. The code employs the full compressible Navier-Stokes equations. The eddy viscosity model of Baldwin and Lomax is used to model the effects of turbulence on the flow. A cell centered finite volume discretization is used for all terms in the governing equations. The Advection Upwind Splitting Method (AUSM) is used to compute the inviscid fluxes, while central differencing is used for the diffusive fluxes. A four-stage Runge-Kutta time integration scheme is used to march solutions to steady state, while convergence is enhanced by a multigrid scheme, local time-stepping and implicit residual smoothing. To enable simulations of flows in complex geometries, the code uses composite structured grid systems where all grid lines are continuous at block boundaries (multiblock grids). Example results are shown a flow in a linear cascade, a flow around a circular pin extending between the main walls in a high aspect-ratio channel, and a flow of air in a radial turbine coolant passage.

Steinthorsson, E.↗

NASA NTRS1993

Development of an explicit multiblock/multigrid flow solver for viscous flows in complex geometries

A new computer program is being developed for doing accurate simulations of compressible viscous flows in complex geometries. The code employs the full compressible Navier-Stokes equations. The eddy viscosity model of Baldwin and Lomax is used to model the effects of turbulence on the flow. A cell centered finite volume discretization is used for all terms in the governing equations. The Advection Upwind Splitting Method (AUSM) is used to compute the inviscid fluxes, while central differencing is used for the diffusive fluxes. A four-stage Runge-Kutta time integration scheme is used to march solutions to steady state, while convergence is enhanced by a multigrid scheme, local time-stepping, and implicit residual smoothing. To enable simulations of flows in complex geometries, the code uses composite structured grid systems where all grid lines are continuous at block boundaries (multiblock grids). Example results shown are a flow in a linear cascade, a flow around a circular pin extending between the main walls in a high aspect-ratio channel, and a flow of air in a radial turbine coolant passage.

Steinthorsson, E.↗

NASA NTRSDate not supplied

Analysis of Ice Mass Growth Over Time on the CRM65 Midspan Hybrid Model

The Aeronautics Research Mission Directorate at NASA is developing and applying tools to enable future technologies towards sustainable flight. Aircraft icing has been identified as a potential barrier to entry into service for innovative designs necessitating improvements to computational ice accretion tools. NASA is developing the Glenn Icing Computational Environment (GlennICE) to address deficiencies in the computational modeling capabilities of previously developed ice accretion solvers. To benchmark and improve the ability to model highly three-dimensional ice accretion, high quality validation data against experimental data is required. The CRM65 Midspan Hybrid geometry was previously tested at the NASA Icing Research Tunnel to generate experimental data for swept wing geometries typical for commercial transport aircraft. As a part of a 2018 icing test campaign, experimental data characterizing the relationship between ice accretion time and ice mass growth was obtained and can be leveraged for use in validation of computational tools. The desire for computational ice accretion solvers to predict ice shapes profiles accreted experimentally has often overshadowed the comparison to the mass and bulk volume of ice accreted. To address this deficiency, an analysis is presented in which GlennICE is applied to simulations of the CRM65 Midspan Hybrid model tested in the NASA Icing Research Tunnel. Results from the computational fluid dynamics simulations compared favorably to the experimental pressure coefficient data, thus validating the modeling setup. The experimental data showed excellent repeatability for the 15.0 minute accretion time. The comparisons between the experimental and computational ice mass over time showed good agreement up to 10.0 minutes after which the ice mass was underpredicted. The experimental ice mass was largely linear with some nonlinear data. The bulk volume of ice accreted experimentally compared well to GlennICE for the scanned ice shapes and mean combined cross section ice shapes, but was underpredicted for the maximum combined cross section ice shapes at longer accretion times. The experimental minimum combined cross section, mean combined cross section, and maximum combined cross section profiles when compared to GlennICE show good agreement for the mean combined cross section up to 15.0 minutes. The analyses show that with a single-shot method, GlennICE currently underpredicts the ice mass for longer accretion times, is not able to match the bulk volume of the maximum combined cross section due to dominating scallop features, and future work is required to generate a more generalized ice bulk density model.

Icing↗

NASA NTRSDate not supplied

Analysis of Ice Mass Growth Over Time on the CRM65 Midspan Hybrid Model

The Aeronautics Research Mission Directorate at NASA is developing and applying tools to enable future technologies towards sustainable flight. Aircraft icing has been identified as a potential barrier to entry into service for innovative designs necessitating improvements to computational ice accretion tools. NASA is developing the Glenn Icing Computational Environment (GlennICE) to address deficiencies in the computational modeling capabilities of previously developed ice accretion solvers. To benchmark and improve the ability to model highly three-dimensional ice accretion, high quality validation data against experimental data is required. The CRM65 Midspan Hybrid geometry was previously tested at the NASA Icing Research Tunnel to generate experimental data for swept wing geometries typical for commercial transport aircraft. As a part of a 2018 icing test campaign, experimental data characterizing the relationship between ice accretion time and ice mass growth was obtained and can be leveraged for use in validation of computational tools. The desire for computational ice accretion solvers to predict ice shapes profiles accreted experimentally has often overshadowed the comparison to the mass and bulk volume of ice accreted. To address this deficiency, an analysis is presented in which GlennICE is applied to simulations of the CRM65 Midspan Hybrid model tested in the NASA Icing Research Tunnel. Results from the computational fluid dynamics simulations compared favorably to the experimental pressure coefficient data, thus validating the modeling setup. The experimental data showed excellent repeatability for the 15.0 minute accretion time. The comparisons between the experimental and computational ice mass over time showed good agreement up to 10.0 minutes after which the ice mass was underpredicted. The experimental ice mass was largely linear with some nonlinear data. The bulk volume of ice accreted experimentally compared well to GlennICE for the scanned ice shapes and mean combined cross section ice shapes, but was underpredicted for the maximum combined cross section ice shapes at longer accretion times. The experimental minimum combined cross section, mean combined cross section, and maximum combined cross section profiles when compared to GlennICE show good agreement for the mean combined cross section up to 15.0 minutes. The analyses show that with a single-shot method, GlennICE currently underpredicts the ice mass for longer accretion times, is not able to match the bulk volume of the maximum combined cross section due to dominating scallop features, and future work is required to generate a more generalized ice bulk density model.

Icing↗

NASA NTRS1999

Computational Assessment of Aft-Body Closure for the HSR Reference H Configuration

A study has been conducted to determine how well the USM3D unstructured Euler solver can be utilized to predict the flow over the High Speed Research (HSR) Reference H configuration with an ultimate goal of prediction of Sting interference so after body closure effects may be evaluated. This study has shown that the code can be used to predict the interference effects of a lower mounted blade sting with a high degree of confidence. It has been shown that wing and fuselage pressures, both levels and trends, can be predicted well. Force and moment levels are not predicted well but experimental trends are predicted. Based upon this, predicted force and moment increments are assumed to be predicted accurately. Deflection of the horizontal tail was found to cause a non-linear increment from the non-deflected sting interference effects.

Londenberg, W. Kelly↗

NASA NTRSDate not supplied

Hardware-Efficient Quantum Optimization Layered Algorithms and Experiments

Quantum optimization algorithms, such as QAOA, that implement parametrized stochastic optimization solvers attempt to identify low-energy solutions of Ising systems by exploiting available quantum effects in noisy-intermediate scale machines. Engineering a well-performing parametrized quantum optimization circuit is indeed an exercise in balancing the trade-off between expressivity and implementation complexity. We show that, for MaxCut QAOA circuits defined on native hardware topology (Rigetti’s Aspen Quantum Processors), error-mitigation techniques recover simulated features of the noiseless theory. Moreover, we explore a design space for QAOA-like ansatze that perform well in theory as well as in hardware for fully-connected problems. We also discuss how efficient coherence and entanglement detection methods that could be coupled with quantum optimization experiments require only linear overhead in benchmarking time.

quantum computing↗

NASA NTRS1987

A generalized procedure for constructing an upwind based TVD scheme

A generalized formulation for constructing second- and higher-order accurate TVD (total variation diminishing) schemes is presented. A given scheme is made TVD by limiting antidiffusive flux differences with some linear functions, so-called limiters. The general idea of the formulation and its mathematical proof of Harten's TVD conditions is shown by applying the Lax-Wendroff method to scalar nonlinear equations and a constant-coefficient system of conservation laws. For the system of equations, several definitions are derived for the argument used in the limiter function and present their performance in numerical experiments. The formulation is extended to the nonlinear system. It is demonstrated that the present procedure can easily convert existing central or upwind, and second- or higher-order differencing schemes to preserve monotonicity and yield physically admissible solutions. The formulation is simple mathematically as well as numerically; both matrix-vector multiplication and Riemann solver are avoided. Although the notion of TVD is based on the initial value problem, application to the steady Euler equations of the formulation is also made.

Liou, Meng-Sing↗

NASA NTRS1990

Domain decomposition methods in aerodynamics

Compressible Euler equations are solved for two-dimensional problems by a preconditioned conjugate gradient-like technique. An approximate Riemann solver is used to compute the numerical fluxes to second order accuracy in space. Two ways to achieve parallelism are tested, one which makes use of parallelism inherent in triangular solves and the other which employs domain decomposition techniques. The vectorization/parallelism in triangular solves is realized by the use of a recording technique called wavefront ordering. This process involves the interpretation of the triangular matrix as a directed graph and the analysis of the data dependencies. It is noted that the factorization can also be done in parallel with the wave front ordering. The performances of two ways of partitioning the domain, strips and slabs, are compared. Results on Cray YMP are reported for an inviscid transonic test case. The performances of linear algebra kernels are also reported.

Venkatakrishnan, V.↗

NASA NTRS1999

An Elasticity-Based Mesh Scheme Applied to the Computation of Unsteady Three-Dimensional Spoiler and Aeroelastic Problems

This paper presents a modification of the spring analogy scheme which uses axial linear spring stiffness with selective spring stiffening/relaxation. An alternate approach to solving the geometric conservation law is taken which eliminates the need for storage of metric Jacobians at previous time steps. Efficiency and verification are illustrated with several unsteady 2-D airfoil Euler computations. The method is next applied to the computation of the turbulent flow about a 2-D airfoil and wing with two and three- dimensional moving spoiler surfaces, and the results compared with Benchmark Active Controls Technology (BACT) experimental data. The aeroelastic response at low dynamic pressure of an airfoil to a single large scale oscillation of a spoiler surface is computed. This study confirms that it is possible to achieve accurate solutions with a very large time step for aeroelastic problems using the fluid solver and aeroelastic integrator as discussed in this paper.

Bartels, Robert E.↗

NASA NTRS2018

Computational Investigation of Nominally-Orthogonal Pneumatic Active Flow Control for High-Lift Systems

We explore the feasibility of using nominally-orthogonal jets as active aerodynamic load control for multi-element high-lift systems, and whether the nominally-orthogonal jets can offer a variety of performance improvements. These nominally-orthogonal jets inject momentum normal to the airfoil surface near the flap trailing edge, where they create a vortex that entrains flow from the opposing side and change the airfoil circulation. Lift-enhancement opportunities of trailing edge nominally-orthogonal jets have previously been studied by Malavard et al. and Blaylock et al. on single-element airfoils; however, their effect on drag was not thoroughly investigated. In this study, we investigate two- dimensional nominally-orthogonal jet effects on both lift and drag on a two-element airfoil, NLR7301. We utilize Chimera Grid Tools to generate structured curvilinear overset grids, and the Reynolds-averaged Navier-Stokes solver OVERFLOW-2 to solve for the flow field around the airfoil. We perform various computational sensitivity studies on the baseline airfoil without a jet to validate computational results against benchmark experimental data. Using a Chimera overset grid topology, we demonstrate a similar lift-enhancement effect between a nominally-orthogonal jet and a nominally-orthogonal physical tab employed at the same location on the studied airfoil. After we introduce the nominally-orthogonal jet concept, we investigate nominally-orthogonal jets with various momentum coefficient settings, C(sub µ) = 0.00 − 0.04 and present a lift-enhancement relationship ∆C(sub l) ≃ 3.59 (C(sub µ)) for this airfoil. We discuss that utilizing a nominally-orthogonal jet with C(sub µ) = 0.01 can shift the linear region of the lift curve by a ∆C(sub l) = 0.36 for the pressure side jet and by a ∆C(sub l) = −0.27 for the suction side jet. Employing a nominally-orthogonal jet is also shown effective in altering the drag. To study the impact, we carry out a drag decomposition study in the form of drag polars. We show for a given C(sub l) = 2.50, a nominally-orthogonal jet with C(sub µ) = 0.01 on the pressure and suction side of the airfoil results in 113 drag count decrements and 41 drag count increments, respectively, compared to the baseline airfoil with no jet. These results show that large and controllable changes in aerodynamic performance can be achieved by relatively small active flow control inputs using the nominally-orthogonal jets presented in this study.

Nominally-Orthogonal↗

NASA NTRS1989

A genuinely multi-dimensional upwind cell-vertex scheme for the Euler equations

The solution of the two-dimensional Euler equations is based on the two-dimensional linear convection equation and the Euler-equation decomposition developed by Hirsch et al. The scheme is genuinely two-dimensional. At each iteration, the data are locally decomposed into four variables, allowing convection in appropriate directions. This is done via a cell-vertex scheme with a downwind-weighted distribution step. The scheme is conservative, and third-order accurate in space. The derivation and stability analysis of the scheme for the convection equation, and the derivation of the extension to the Euler equations are given. Preconditioning techniques based on local values of the convection speeds are discussed. The scheme for the Euler equations is applied to two channel-flow problems. It is shown to converge rapidly to a solution that agrees well with that of a third-order upwind solver.

Powell, Kenneth G.↗

NASA NTRS2002

Multi-dimensional Upwind Fluctuation Splitting Scheme with Mesh Adaption for Hypersonic Viscous Flow

A multi-dimensional upwind fluctuation splitting scheme is developed and implemented for two-dimensional and axisymmetric formulations of the Navier-Stokes equations on unstructured meshes. Key features of the scheme are the compact stencil, full upwinding, and non-linear discretization which allow for second-order accuracy with enforced positivity. Throughout, the fluctuation splitting scheme is compared to a current state-of-the-art finite volume approach, a second-order, dual mesh upwind flux difference splitting scheme (DMFDSFV), and is shown to produce more accurate results using fewer computer resources for a wide range of test cases. A Blasius flat plate viscous validation case reveals a more accurate upsilon-velocity profile for fluctuation splitting, and the reduced artificial dissipation production is shown relative to DMFDSFV. Remarkably, the fluctuation splitting scheme shows grid converged skin friction coefficients with only five points in the boundary layer for this case. The second half of the report develops a local, compact, anisotropic unstructured mesh adaptation scheme in conjunction with the multi-dimensional upwind solver, exhibiting a characteristic alignment behavior for scalar problems. The adaptation strategy is extended to the two-dimensional and axisymmetric Navier-Stokes equations of motion through the concept of fluctuation minimization.

Wood, William A., III↗

NASA NTRSDate not supplied

Surface-Normal Active Flow Control for Lift Enhancement and Separation Mitigation for High-Lift Common Research Model

This study explores the feasibility of using small surface-normal jets near the flap trailing edge as active aerodynamic load control on the high-lift Common Research Model wing/-body configuration. Chimera Grid Tools are utilized to generate structured curvilinear overset grids, and the Reynolds-averaged Navier-Stokes solver OVERFLOW is employed to solve for the flow-field around the geometry. The so-called microjet is initially employed across both the inboard and the outboard flaps on the pressure-side near the trailing edge. It is shown that implementing the microjet on the inboard flap is more effective compared to implementing it on the outboard flap. This is because, prior to microjet implementation, the flow on the outboard flap exhibits extensive separation, while the flow on the inboard flap exhibits moderate separation. For microjet implementation across the inboard flap only, the relationship between momentum coefficient of the microjet and lift-enhancement is found to be∆CL'1.66√Cμfor the rangeCμ= 0.00−0.012. We show that implementing a microjet with a jet velocity ratio of one, which corresponds toCμ= 0.003, can shift the linear region of the lift curve by ∆CL= 0.08. The linear shift in the lift curve is significant for enhancing airplane performance such as increasing its payload. Microjet implementation effects on the drag coefficient are also investigated through a drag decomposition analysis. Further, we employ an induced drag analysis based on the spanwise load distribution and show that the microjet-related increase in pressure drag coefficient is dominated by the increase in the induced drag while microjet implementation reduces the form drag. These preliminary results show that favorable changes in aerodynamic performance can be achieved by using the surface-normal jets presented in this study.

ARMD↗

NASA NTRS2023

CFD Integrated Transition Modeling for High-Speed Flows via Coupled OVERFLOW-LASTRAC Analysis

This work details ongoing efforts at the NASA Langley Research Center to develop and validate a general-use CFD tool that includes built-in predictions of boundary-layer transition in high-speed flows. Existing tools for the coupling of the NASA OVERFLOW structured overset RANS solver and LASTRAC stability analysis code have been extended to capture boundary-layer transition in high-speed flows driven by either Mack’s first-mode or secondmode instabilities and/or crossflow instabilities. The efficacy of this coupled approach has been demonstrated by examining a variety of supersonic and hypersonic test cases for which experimental validation data is available. The intermittency prescription parameters inherited from prior low-speed applications are found to be suitable for some, but not all high-speed flow scenarios. The method is found to be robust for straight cone configurations and improvements necessary to accurately capture transition on geometries with spatially complex amplification factor envelopes with intermediate regions of slow N-factor variation are examined. The automated, coupled analysis is demonstrated for a 3d supersonic test case and found to perform well within the limits of the linear stability analysis on which it relies. Finally, a preliminary investigation of the method’s robustness to non-ideal CFD meshes is conducted.

High-speed flow↗

NASA NTRS2014

Adjoint Methods for Adjusting Three-Dimensional Atmosphere and Surface Properties to Fit Multi-Angle/Multi-Pixel Polarimetric Measurements

This paper derives an efficient procedure for using the three-dimensional (3D) vector radiative transfer equation (VRTE) to adjust atmosphere and surface properties and improve their fit with multi-angle/multi-pixel radiometric and polarimetric measurements of scattered sunlight. The proposed adjoint method uses the 3D VRTE to compute the measurement misfit function and the adjoint 3D VRTE to compute its gradient with respect to all unknown parameters. In the remote sensing problems of interest, the scalar-valued misfit function quantifies agreement with data as a function of atmosphere and surface properties, and its gradient guides the search through this parameter space. Remote sensing of the atmosphere and surface in a three-dimensional region may require thousands of unknown parameters and millions of data points. Many approaches would require calls to the 3D VRTE solver in proportion to the number of unknown parameters or measurements. To avoid this issue of scale, we focus on computing the gradient of the misfit function as an alternative to the Jacobian of the measurement operator. The resulting adjoint method provides a way to adjust 3D atmosphere and surface properties with only two calls to the 3D VRTE solver for each spectral channel, regardless of the number of retrieval parameters, measurement view angles or pixels. This gives a procedure for adjusting atmosphere and surface parameters that will scale to the large problems of 3D remote sensing. For certain types of multi-angle/multi-pixel polarimetric measurements, this encourages the development of a new class of three-dimensional retrieval algorithms with more flexible parametrizations of spatial heterogeneity, less reliance on data screening procedures, and improved coverage in terms of the resolved physical processes in the Earth's atmosphere.

linearization↗

NASA NTRS2014

Adjoint Methods for Adjusting Three-Dimensional Atmosphere and Surface Properties to Fit Multi-Angle Multi-Pixel Polarimetric Measurements

This paper derives an efficient procedure for using the three-dimensional (3D) vector radiative transfer equation (VRTE) to adjust atmosphere and surface properties and improve their fit with multi-angle/multi-pixel radiometric and polarimetric measurements of scattered sunlight. The proposed adjoint method uses the 3D VRTE to compute the measurement misfit function and the adjoint 3D VRTE to compute its gradient with respect to all unknown parameters. In the remote sensing problems of interest, the scalar-valued misfit function quantifies agreement with data as a function of atmosphere and surface properties, and its gradient guides the search through this parameter space. Remote sensing of the atmosphere and surface in a three-dimensional region may require thousands of unknown parameters and millions of data points. Many approaches would require calls to the 3D VRTE solver in proportion to the number of unknown parameters or measurements. To avoid this issue of scale, we focus on computing the gradient of the misfit function as an alternative to the Jacobian of the measurement operator. The resulting adjoint method provides a way to adjust 3D atmosphere and surface properties with only two calls to the 3D VRTE solver for each spectral channel, regardless of the number of retrieval parameters, measurement view angles or pixels. This gives a procedure for adjusting atmosphere and surface parameters that will scale to the large problems of 3D remote sensing. For certain types of multi-angle/multi-pixel polarimetric measurements, this encourages the development of a new class of three-dimensional retrieval algorithms with more flexible parametrizations of spatial heterogeneity, less reliance on data screening procedures, and improved coverage in terms of the resolved physical processes in the Earth׳s atmosphere.

adjoint methods↗

NASA NTRS2023

Evaluation of Transport-Equation-Based Transition Models for High-Speed Boundary Layers Using OVERFLOW

Accurate modeling of laminar-turbulent transition is crucial for the design of hypersonic flight systems. However, the current transition models used in production CFD codes are insufficient for high-speed flows. Many extensions to low-speed models have been suggested; however, a thorough verification and validation effort is needed before these models can be used in design settings. Challenges include potentially missing details of the model implementation requirements and/or a complete specification of the input parameters needed to replicate the test findings. A meaningful assessment of the generalization capability of these models is also hindered by a lack of information regarding the specific flow configurations and associated grids employed for model calibration. As a key first step toward model verification, we present an independent assessment of two recently proposed models for high-speed transition, namely, a model within the SST-$\gamma$ framework and a model based on the SST-$\gamma-\nu_L$ equations. These models are implemented in the NASA OVERFLOW 2.3e solver and their performance in predicting first mode, second mode, and crossflow transition has been evaluated for several test cases in the supersonic and hypersonic regimes. Besides the test cases employed by the model developers, which could have also been used for model calibration, the present assessment includes supplementary configurations that contribute to an unbiased assessment of the models. The outcomes presented in this study indicate the potential for the models to be applied to high-speed flight configurations. Key steps toward future improvements to these models are also outlined.

High-speed flow↗