Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Experimental evaluation of trailing edge and incidence fluctuation noise theories

Tests were conducted to evaluate conflicting theories for trailing edge noise and for incidence fluctuation noise. A flat-plate airfoil with flush-mounted surface pressure transducers was tested in an anechoic wind tunnel at velocities from 31.5 to 177 m/sec and nominal 4 and 6% grid-generated turbulence levels. In one series of runs, the airfoil was faired into the tunnel nozzle and extended beyond the nozzle lip for studies of trailing edge noise without a leading edge and with flow on only one side. Such noise was found to vary with velocity to the fifth power and turbulence level squared as predicted by Ffowcs Williams and Hall (1970) and by Chase (1972). Power spectral density at high frequencies decayed approximately inversely with frequency to the 10/3 power as predicted by Chase. The data were poorly predicted by Hayden's correlation (1969, 1972).

Fink, M. R.↗
NASA NTRS1975

Simulation by vortex rings of the unsteady pressure field near a jet

A coordinated theoretical and experimental program has been undertaken to construct a model for the shedding of vortex rings in order to simulate the real-time pressure variation in the acoustic region near the jet. The basic parameters in the analytic solutions are the eddy viscosity coefficient and the time intervals between successive shedding of vortex rings from the nozzle lip. The experimental and theoretical results show good qualitative agreement.

Liu, C. H.↗
NASA NTRS1976

Cost saving synergistic shaft seal

Segmented carbon rings, used to replace elastomeric seal lip, provide resistance to high temperatures generated in lubricating film. Machining and close manufacturing tolerances of conventional segmented seal are avoided by mounting segmented rings in elastomeric flex section.

Ludwig, L. P.↗
NASA NTRS1975

A new wind energy conversion system

It is presupposed that vertical axis wind energy machines will be superior to horizontal axis machines on a power output/cost basis and the design of a new wind energy machine is presented. The design employs conical cones with sharp lips and smooth surfaces to promote maximum drag and minimize skin friction. The cones are mounted on a vertical axis in such a way as to assist torque development. Storing wind energy as compressed air is thought to be optimal and reasons are: (1) the efficiency of compression is fairly high compared to the conversion of mechanical energy to electrical energy in storage batteries; (2) the release of stored energy through an air motor has high efficiency; and (3) design, construction, and maintenance of an all-mechanical system is usually simpler than for a mechanical to electrical conversion system.

Smetana, F. O.↗
NASA NTRS1976

Laser induced photoluminescence spectroscopy of cometary radicals

Flash photolysis together with laser excitation of the product fragments was used in laboratory studies of cometary radicals. The LIPS method has been applied to the CN radical to determine: (1) Radiative lifetimes of individual rotational levels in the zeroth vibrational level of the B state; (2) energy partitioning during photodissociation of C2N2; and (3) vibrational and rotational excitation during formation of CN radicals in the photodissociation of dicyanoacetylene.

Jackson, W. M.↗
NASA NTRS1976

Noise suppression with high Mach number inlets

Experimental results were obtained for two types of high Mach number inlets, one with a translating centerbody and a fixed geometry inlet (collapsing cowl) with no centerbody. The aerodynamic and acoustic performance of these inlets was examined. The effects of area ratio, length/diameter ratio, and lip geometry were among several parameters investigated. The translating centerbody type inlet was found to be superior to the collapsing cowl both acoustically and aerodynamically, particularly for area ratios greater than 1.5. Comparison of length/diameter ratio and area ratio effects on performance near choked flow showed the latter to be more significant. Also, greater high frequency noise attenuation was achieved by increasing Mach number from low to high subsonic values.

Lumsdaine, E.↗
NASA NTRS1975

Effect of crack initiation, stable crack growth and unstable crack propagation on the crack-tip plastic zone

A technique for measuring the plastic zones associated with initial crack-tip yielding, subcritical crack growth, and unstable fracture is discussed. The results of the measurement of the locus of these yield regions, on center-cracked sheet and compact tension specimens of 7075-T6, 7075-T651, and 2024-T3 aluminum, are reported in this paper. It was found that a very accurate representation of the strains was obtained by this method and that the results added significant insight into the fracture process. The plastic zones were found to be approximately eight times wider in 2024-T3 than in the 7075-T6 sheets. The yield zones approached a maximum value after unstable fracture was attained and maintained that size through the fast fracture region. As expected, the plastic zones in the compact tension specimen were associated only with the formation of the shear lips and no plastic zones were observed in the fatigue precracked regions of either the center-cracked or compact-tension specimens.

Poulose, P. K.↗
NASA NTRS1976

Effect of geometry modifications on effectiveness of slot injection in hypersonic flow

The study presents wind-tunnel measurements of surface static pressures, equilibrium temperatures, and skin friction downstream of tangential slot injection into a thick turbulent hypersonic boundary layer from two modified slot configurations. The data are compared with results obtained for baseline configurations reported by Cary and Hefner (1970, 1972) to determine whether simple modifications to the slot configuration can produce improved cooling effectiveness and skin friction reduction. The baseline slot configurations are simply modified by thickening the slot lip and by elevating the location of the slot exit above the flat plate. Although the results indicate that simple modifications of the baseline slot configurations can enhance the skin friction reductions obtained with tangential slot injection, slot base drag estimates show that neither of the modifications will lessen the impact of the systems penalties for collecting, ducting, and injecting the slot air.

Hefner, J. N.↗
NASA NTRS1976

Hollow lunar spherules and microcratering

Craters were generated by micrometer-size, thin-walled hollow glass spheres impacting glass and stainless steel targets to determine morphological features distinguishing craters formed by hollow spheres from those formed by solid projectiles. The craters formed in both targets differed from those formed by solid spherical projectiles in that the central pit is an annular rather than a cup-shaped depression. The existence of an annular crater morphology on a surface exposed to cosmic dust would indicate the presence of thin-walled hollow spherules. Penetrations of thin-walled hollow glass beads by high velocity, solid, micrometer-size spheres are characterized by inward and outward flowing lips showing asymmetries dependent on the angle of impact.

Vedder, J. F.↗
NASA NTRS1976

Vortex shedding from a blunt trailing edge with equal and unequal external mean velocities

A flow-visualization study has shown that strong Karman vortices develop behind the blunt trailing edge of a plate when the free-stream velocities over both surfaces are equal and that the vortices tend to disappear when the surface velocities are unequal. This observation provides an explanation for the occurence and disappearance of certain discrete tones often found to be present in the noise spectra of coaxial jets. Both the vortex formation and the tones occur at a Strouhal number based on the lip thickness and the average of the external steady-state velocities of about 0.2. Results from theoretical calculations of the vortex formation, based on an inviscid incompressible analysis of the motion of point vortices, were in good agreement with the experimental observations.

Boldman, D. R.↗
NASA NTRS1976

Systematic study of error sources in supersonic skin-friction balance measurements

An experimental study was performed to investigate potential error sources in data obtained with a self-nulling, moment-measuring, skin-friction balance. The balance was installed in the sidewall of a supersonic wind tunnel, and independent measurements of the three forces contributing to the balance output (skin friction, lip force, and off-center normal force) were made for a range of gap size and element protrusion. The relatively good agreement between the balance data and the sum of these three independently measured forces validated the three-term model used. No advantage to a small gap size was found; in fact, the larger gaps were preferable. Perfect element alignment with the surrounding test surface resulted in very small balance errors. However, if small protrusion errors are unavoidable, no advantage was found in having the element slightly below the surrounding test surface rather than above it.

Allen, J. M.↗
NASA NTRS1977

Investigation of normal shock inlets for highly maneuverable aircraft

Concepts are investigated for obtaining both low cowl drag and good inlet performance at high angles of attack. The effect of a canard on inlet performance for a kidney shaped inlet in each of two vertical locations is discussed along with a sharp lip two dimensional inlet on a canardless forebody.

Martin, A. W.↗
NASA NTRS1977

Aerodynamic performance of 0.4066-scale model of JT8D refan stage with S-duct inlet

A scale model of the JT8D refan stage was tested with a scale model of the S-duct inlet design for the refanned Boeing 727 center engine. Detailed survey data of pressures, temperatures, and flow angles were obtained over a range of flows at speeds from 70 to 97 percent of design speed. Two S-duct configurations were tested; one with a bellmouth inlet and the other with a flight lip inlet. The results indicated that the overall performance was essentially unaffected by the distortion generated by the S-duct inlet. The stall weight flow increased by less than 0.5 kg/sec (approximately 1.5% of design flow) with the S-duct inlet compared with that obtained with uniform flow. The detailed measurements indicated that the inlet guide vane (IGV) significantly reduced circumferential variations. For example, the flow angles ahead of the IGV were positive in the right half of the inlet and negative in the left half. Behind the IGV, the flow angles tended to be more uniform circumferentially.

Moore, R. D.↗
NASA NTRS1975

Design and control of a manipulator for tetraplegics

A concept for the design of a manipulator for tetraplegics must be based on the mutual adaptation of system determining properties of the disabled operator, the manipulator, and the environment. Because the reduced capability of tetraplegics allows control of only three degrees of freedom at a time (instead of the normal fifteen), the structure of the environment must be adjusted. A manipulator is described which includes a three dimensional control stick operated by the lips and mouth.

Paeslack, V.↗
NASA NTRS1977

An experimental investigation of a three dimensional wall jet

One and two point statistical properties are measured in the flow fields of a coflowing turbulent jet. Two different confining surfaces (one flat, one with large curvature) are placed adjacent to the lip of the circular nozzle; and the resultant effects on the flow field are determined. The one point quantities measured include mean velocities, turbulent intensities, velocity and concentration autocorrelations and power spectral densities, and intermittencies. From the autocorrelation curves, the Taylor microscale and the integral length scale are calculated. Two point quantities measured include velocity and concentration space-time correlations and pressure velocity correlations. From the velocity space-time correlations, iso-correlation contours are constructed along with the lines of maximum maximorum. These lines allow a picture of the flow pattern to be determined. The pressures monitored in the pressure velocity correlations are measured both in the flow field and at the surface of the confining wall(s).

Catalano, G. D.↗
NASA NTRS1977

Study of noise and inflow distortion sources in the NASA QF-1B fan using measured blade and vane pressures

Pressure transducers were installed on the blades and vanes of QF-1B, a transonic-tip-speed fan from the NASA Quiet Fan Program which was tested on the outdoor quiet fan test facility at NASA-Lewis. Signals from the transducers and from far field microphones were analyzed to determine sources of nonuniform inflow and noise. The nonuniform inflow was mostly unsteady with roughly equal contributions from atmospheric turbulence and rig interference. The rig interference was largest at the bottom and appeared to be generated by the support structure which was located behind the inlet lip under the fan. Interaction of this inflow distortion was the dominant source of noise at 1, 2, and 3 times blade passing frequency (BPF) at 60, 70, and 80 percent of design speed. At 90 percent speed, noise at BPF was dominated by the steady rotor field. A broadband spectrum peak centered at about 2.2 times BPF was identified as rotor/stator interaction stemming from a high frequency rotor exit flow component. The remaining broadband energy from 0.3 to 3.5 times BPF was attributed to the better known type of rotor/stator interaction associated with rotor wake turbulence.

Hanson, D. B.↗
NASA NTRS1977

Over-the-wing model thrust reverser noise tests

Static acoustic tests were conducted on a 1/12 scale model over-the-wing target type thrust reverser. The model configuration simulates a design that is applicable to the over-the-wing short-haul advanced technology engine. Aerodynamic screening tests of a variety of reverser designs identified configurations that satisfied a reverse thrust requirement of 35 percent of forward thrust at a nozzle pressure ratio of 1.29. The variations in the reverser configuration included, blocker door angle, blocker door lip angle and shape, and side skirt shape. Acoustic data are presented and compared for the various configurations. The model data scaled to a single full size engine show that peak free field perceived noise (PN) levels at a 152.4 meter sideline distance range from 98 to 104 PNdb.

Goodykoontz, J.↗
NASA NTRS1977

Experimental study of error sources in skin-friction balance measurements

An experimental study has been performed to determine potential error sources in skin-friction balance measurements. A floating-element balance, large enough to contain the instrumentation needed to systematically investigate these error sources has been constructed and tested in the thick turbulent boundary layer on the sidewall of a large supersonic wind tunnel. Test variables include element-to-case misalignment, gap size, and Reynolds number. The effects of these variables on the friction, lip, and normal forces have been analyzed. It was found that larger gap sizes were preferable to smaller ones; that small element recession below the surrounding test surface produced errors comparable to the same amount of protrusion above the test surface; and that normal forces on the element were, in some cases, large compared to the friction force.

Allen, J. M.↗