Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Landing Gear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Volumetric pattern analysis of airborne antennas

By blending together the roll and elevation plane high-frequency solutions, a very efficient technique has been developed for the volumetric pattern analysis of antennas mounted on the fuselage of a generalized aircraft. The fuselage is simulated by an infinitely long, perfectly conducting, elliptic cylinder in cross section and a composite elliptic cylinder in profile. The wings, nose section, stabilizers, and landing-gear doors may be modeled by finite flat or bent plates. Good agreement with accurate scale model measurements has been obtained for a variety of airborne antenna problems.

Yu, C. L.↗
NASA NTRS1979

Airframe noise component interaction studies

Acoustic wind tunnel tests were conducted of a two-dimensional wing section with removable high-lift leading and trailing edge devices and a removeable two-wheel landing gear with open cavity. An array of far field conventional microphones and an acoustic mirror directional microphone were utilized to determine far field spectrum levels and noise source distribution. Data were obtained for the wing with components deployed separately and in various combinations. The basic wing model had 0.305 m (1.00 ft) chord, which is roughly 1/10 scale for a one-hundred passenger transport airplane. Most of the data were obtained at 70.7 and 100 m/sec (232 and 328 ft/sec) airspeeds, which bracket the range of practical approach speeds for such aircraft. Data were obtained at frequence to 40 kHz so that, when scaled to s typical full-airframe, the frequency region which strongly influences preceived noise level would be included.

Fink, M. R.↗
NASA NTRS1979

A turbojet-boosted two-stage-to-orbit space transportation system design study

The concept to use twin turbo-powered boosters for acceleration to supersonic staging speed followed by an all rocket powered orbiter stage was proposed. A follow-on design study was then made of the concept with the performance objective of placing a 29,483 Kg payload into a .2.6 X 195.3 km orbit. The study was performed in terms of analysis and trade studies, conceptual design, utility and economic analysis, and technology assessment. Design features of the final configuration included: strakes and area rule for improved take off and low transonic drag, variable area inlets, exits and turbine, and low profile fixed landing gear for turbojet booster stage. The payload required an estimated GLOW of 1,270,000 kg for injection in orbit. Each twin booster required afterburning turbojet engines each with a static sea level thrust rating of 444,800 N. Life cycle costs for this concept were comparable to a SSTO/SLED concept except for increased development cost due to the turbojet engine propulsion system.

Hepler, A. K.↗
NASA NTRS1979

Airframe noise component interaction studies

Acoustic wind tunnel tests were conducted to examine the noise-generating processes of an airframe during approach flight. The airframe model was a two-dimensional wing section, to which highlift leading and trailing edge devices and landing gear could be added. Far field conventional microphones were utilized to determine component spectrum levels. An acoustic mirror directional microphone was utilized to examine noise source distributions on airframe components extended separately and in combination. Measured quantities are compared with predictions inferred from aircraft flyover data. Aeroacoustic mechanisms for each airframe component are identified. Component interaction effects on total radiated noise generally were small (within about 2 dB). However, some interactions significantly redistributed the local noise source strengths by changing local flow velocities and turbulence levels. Possibilities for noise reduction exist if trailing edge flaps could be modified to decrease their noise radiation caused by incident turbulent flow.

Fink, M. R.↗
NASA NTRS1979

Multirole cargo aircraft options and configurations

A future requirements and advanced market evaluation study indicates derivatives of current wide-body aircraft, using 1980 advanced technology, would be economically attractive through 2008, but new dedicated airfreighters incorporating 1990 technology, would offer little or no economic incentive. They would be economically attractive for all payload sizes, however, if RD and T costs could be shared in a joint civil/military arrangement. For the 1994-2008 cargo market, option studies indicate Mach 0.7 propfans would be economically attractive in trip cost, aircraft price and airline ROI. Spanloaders would have an even lower price and higher ROI but would have a relatively high trip cost because of aerodynamic inefficiencies. Dedicated airfreighters using propfans at Mach 0.8 cruise, laminar flow control, or cryofuels, would not provide any great economic benefits. Air cushion landing gear configurations are identified as an option for avoiding runway constraints on airport requirements and/or operational constraints are noted.

Conner, D. W.↗
NASA NTRS1980

Conceptual study of an advanced supersonic technology transport (AST-107) for transpacific range using low-bypass-ratio turbofan engines

An advanced supersonic technology configuration concept designated the AST-107, using a low bypass ratio turbofan engine, is described and analyzed. The aircraft had provisions for 273 passengers arranged five abreast. The cruise Mach number was 2.62. The mission range for the AST-107 was 8.48 Mm (4576 n.mi.) and an average lift drag ratio of 9.15 during cruise was achieved. The available lateral control was not sufficient for the required 15.4 m/s (30 kt) crosswind landing condition, and a crosswind landing gear or a significant reduction in dihedral effect would be necessary to meet this requirement. The lowest computed noise levels, including a mechanical suppressor noise reduction of 3 EPNdB at the flyover and sideline monitoring stations, were 110.3 EPNdB (sideline noise), 113.1 EPNdB (centerline noise) and 110.5 EPNdB (approach noise).

Morris, S. J., Jr.↗
NASA NTRS1980

Development and test results of a flight management algorithm for fuel conservative descents in a time-based metered traffic environment

A simple flight management descent algorithm designed to improve the accuracy of delivering an airplane in a fuel-conservative manner to a metering fix at a time designated by air traffic control was developed and flight tested. This algorithm provides a three dimensional path with terminal area time constraints (four dimensional) for an airplane to make an idle thrust, clean configured (landing gear up, flaps zero, and speed brakes retracted) descent to arrive at the metering fix at a predetermined time, altitude, and airspeed. The descent path was calculated for a constant Mach/airspeed schedule from linear approximations of airplane performance with considerations given for gross weight, wind, and nonstandard pressure and temperature effects. The flight management descent algorithm is described. The results of the flight tests flown with the Terminal Configured Vehicle airplane are presented.

Knox, C. E.↗
NASA NTRS1979

Multirole cargo aircraft options and configurations

The paper discusses multirole cargo aircraft options and configurations. It was shown that derivatives of current wide-body aircraft would be economically attractive through 2008, but new dedicated airfreighters incorporating 1990 technology would offer little or no economic incentive. Option studies indicate that Mach 0.7 propfans would be economically attractive in trip cost, aircraft price, and airline ROI; spanloaders would be lower priced with higher ROI, but would have a relatively higher trip cost because of aerodynamic inefficiencies. Finally, air cushion landing gear configurations are identified as an option for avoiding runway constraints on airport accommodation of very large airfreighters.

Conner, D. W.↗
NASA NTRS1980

Outlook for advanced concepts in transport aircraft

The present air transport system is expected to continue until the turn of the century, but significant technological advances will have been incorporated into the existing aircraft. With a few exceptions, such as the SST, the development of all-new transports will be inhibited by economic constraints. The outlook for advanced transport aircraft concepts in the 21st century indicates new vehicles may be developed, such as air cushion landing gears, away from the airport; flatbed transports, at the airport; and aerial relay transports, in the air. Some of the new technologies and vehicle configurations are discussed, and their impact on aircraft maintenance, airport runways, taxiways, and cargo loading facilities is examined.

Conner, D. W.↗
NASA NTRS1982

Flight-Management Algorithm for Fuel-Conservative Descents

Federal Aviation Administration has developed an automated time-based metering form of air traffic control for arrivals into terminal area called local flow management/profile descent (LFM/PD). LFM/PD saves fuel by matching airplane arrival flow to airport acceptance rate through time-control computations and by allowing pilot to descend at his discretion from cruise altitude to metering fix in an idle-thrust, clean configuration (landing gear up, flaps zero, speed brakes retracted).

Knox, C. E.↗
NASA NTRS1981

Test results of flight guidance for fuel conservative descents in a time-based metered air traffic environment

The NASA developed, implemented, and flight tested a flight management algorithm designed to improve the accuracy of delivering an airplane in a fuel-conservative manner to a metering fix at a time designated by air traffic control. This algorithm provides a 3D path with time control (4D) for the TCV B-737 airplane to make an idle-thrust, clean configured (landing gear up, flaps zero, and speed brakes retracted) descent to arrive at the metering fix at a predetermined time, altitude, and airspeed. The descent path is calculated for a constant Mach/airspeed schedule from linear approximations of airplane performance with considerations given for gross weight, wind, and nonstandard pressure and temperature effects. The flight management descent algorithms are described and flight test results are presented.

Knox, C. E.↗
NASA NTRS1980

Aircraft wing weight build-up methodology with modification for materials and construction techniques

An aircraft wing weight estimating method based on a component buildup technique is described. A simplified analytically derived beam model, modified by a regression analysis, is used to estimate the wing box weight, utilizing a data base of 50 actual airplane wing weights. Factors representing materials and methods of construction were derived and incorporated into the basic wing box equations. Weight penalties to the wing box for fuel, engines, landing gear, stores and fold or pivot are also included. Methods for estimating the weight of additional items (secondary structure, control surfaces) have the option of using details available at the design stage (i.e., wing box area, flap area) or default values based on actual aircraft from the data base.

York, P.↗
NASA NTRS1981

Development of simplified airborne computations for fuel conservative descents in a time-based metered air traffic environment

The NASA has developed and flight-tested a simple flight management descent algorithm designed to improve the accuracy of delivering an airplane in a fuel-conservative manner to a metering fix at a time designated by air traffic control. This algorithm provides a three-dimensional path with terminal area time constraints (four-dimensional) for an airplane to make an idle-thrust, clean-configured (landing gear up, flaps zero, and speed brakes retracted) descent to arrive at the metering fix at a predetermined time, altitude, and airspeed. The descent path is calculated for a constant Mach/airspeed schedule from linear approximations of airplane performance with considerations given for gross weight, wind, and nonstandard pressure and temperature effects. Applications of the four-dimensional and descent planning capabilities of the algorithm to conventional airplanes is being investigated. This report describes the flight management descent algorithm and presents the results of the flight tests flown with the Terminal Configured Vehicle airplane.

Knox, C. E.↗
NASA NTRS1983

Aerospace safety advisory panel

Data acquired on the actual flight experience with the various subsystems are assessed. These subsystems include: flight control and performance, structural integrity, orbiter landing gear, lithium batteries, EVA and prebreathing, and main engines. Improvements for routine operations are recommended. Policy issues for operations and flight safety for aircraft operations are discussed.

Source record↗
NASA NTRS1983

Structural response of transport airplanes in crash situations

This report highlights the results of contractural studies of transport accident data undertaken in a joint research program sponsored by the FAA and NASA. From these accident data studies it was concluded that the greatest potential for improved transport crashworthiness is in the reduction of fire related fatalities. Accident data pertaining to fuselage integrity, main landing gear collapse, fuel tank rupture, wing breaks, tearing of tank lower surfaces, and engine pod scrubbing are discussed. In those accidents where the energy absorbing protective capability of the fuselage structure is expended and the airplane experiences major structural damage, trauma caused fatalities are also discussed. The dynamic performance of current seat/restraint systems are examined but it is concluded that the accident data does not adequately define the relationship between occupant response and the dynamic interaction with the seat, floor and fuselage structure.

Thomson, R. G.↗
NASA NTRS1983

Safe-life and damage-tolerant design approaches for helicopter structures

The safe-life and damage-tolerant design approaches discussed apply to both metallic and fibrous composite helicopter structures. The application of these design approaches to fibrous composite structures is emphasized. Safe-life and damage-tolerant criteria are applied to all helicopter flight critical components, which are generally categorized as: dynamic components with a main and tail rotor system, which includes blades, hub and rotating controls, and drive train which includes transmission, and main and interconnecting rotor shafts; and the airframe, composed of the fuselage, aerodynamic surfaces, and landing gear.

Reddick, H. K., Jr.↗
NASA NTRS1983

Hydrazine gas generator performance on Space Shuttle

The design, functions, performance, and applications of the hydrazine gas generators (GG) on the STS are detailed. The GGs provide gas horse power for the APUs that drive the hydraulic pumps on the SRBs, which have two cross-linked systems. The Orbiter has three-cross-linked APU systems, used for gimballing the main engine and booster nozzles, actuating the main engine fuel valves and the ET umbilical disconnect, actuation of the control surfaces, and powering the landing gear, brakes, and nose wheel steering. The major design components of the Orbiter GGs are an injector, a catalyst bed, a decomposition chamber, an exhaust nozzle, and an interface structure, with the main structural material being Hasteloy B. Hydrazine injected and dispersed into the catalyst bed decomposes into gas and exits for expansion in an APU turbine. Twenty-six GGs have flown on missions STS-1 through STS-6 with over three tons of hydrazine having been expended over 44 hr of operations, as no refurbishment to that point was necessary.

Patterson, I. J.↗