Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Iterative limiters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Deployment mechanisms for high packing efficiency One-MEter Reflectarray Antenna (OMERA)

While the capabilities of CubeSats have greatly increased in the past years, large, deployable high frequency apertures remain a limitation. The goal of this work is to develop a large 1 meter antenna operating at 35.75 GHz for RADAR applications. A reflectarray design was selected, as the flat panels are compatible with the CubeSat form factor. A center-fed, Cassegrain configuration was selected for the feed, to minimize deployed height. The flat panel configuration and Cassegrain feed allowed the entire 1 meter antenna to be compatible with a 6U bus, leaving a little under 4U of volume for remaining instrument and spacecraft components. Several iterations of the design have been built and tested, with an RF test of a fully deployed assembly being completed most recently. Prior to constructing the flight model, another iteration will need to be built and tested. The goal is to have the antenna flight ready before 2020.

Cwik, Tom↗

Deployment Mechanisms for High Packing Efficiency OneMeter Reflectarray Antenna (OMERA)

While the capabilities of CubeSats have greatly increased in the past years, large, deployable high frequency apertures remain a limitation. The goal of this work was to develop a large 1 meter antenna operating at 35.75 Ghz for RADAR applications. A reflectarray design was selected, as the flat panels were compatible with the CubeSat form factor. A center-fed, Cassegrain configuration was selected for the feed, to minimize deployed height. The flat panel configuration and Cassegrain feed allowed the entire 1 meter antenna to be compatible with a 6U bus, leaving a little under 4U of volume for remaining instrument and spacecraft components. Several iterations of the design have been built and tested, with an RF test of a fully deployed assembly being completed most recently. The goal is to have the antenna flight ready before 2020.

Cwik, Tom↗

Evaluation of a Seat Attenuation System for the Orion Crew Module

The function of the crew seat attenuation system for the Orion Crew Module (CM) is to provide the crew with a low injury-risk landing environment under a range of crew configurations and landing conditions. The current design for the seat attenuation system provides the crew with a low risk of injury environment based on the Brinkley criteria for most of the landing conditions considered. Furthermore, the stroking of the seat attenuation system is within limits, and the clearance between the seat support platform and vehicle is not exceeded. For the limited number of landing conditions where a low injury risk is exceeded, the risk is never beyond a moderate level. The results presented in this study are based on a CM structural model that is rigid except for the pallet struts, which attenuate landing loads and reduce the accelerations transferred to the astronauts. The CM simulations include a soft soil landing. Several different crew configurations are evaluated in this study. It is expected that situations where the risk is above low can be eliminated in future design iterations.

Lawrence, Charles↗

Linear and nonlinear dynamic analysis of redundant load path bearingless rotor systems

The goal of this research is to develop the transfer matrix method to treat nonlinear autonomous boundary value problems with multiple branches. The application is the complete nonlinear aeroelastic analysis of multiple-branched rotor blades. Once the development is complete, it can be incorporated into the existing transfer matrix analyses. There are several difficulties to be overcome in reaching this objective. The conventional transfer matrix method is limited in that it is applicable only to linear branch chain-like structures, but consideration of multiple branch modeling is important for bearingless rotors. Also, hingeless and bearingless rotor blade dynamic characteristics (particularly their aeroelasticity problems) are inherently nonlinear. The nonlinear equations of motion and the multiple-branched boundary value problem are treated together using a direct transfer matrix method. First, the formulation is applied to a nonlinear single-branch blade to validate the nonlinear portion of the formulation. The nonlinear system of equations is iteratively solved using a form of Newton-Raphson iteration scheme developed for differential equations of continuous systems. The formulation is then applied to determine the nonlinear steady state trim and aeroelastic stability of a rotor blade in hover with two branches at the root. A comprehensive computer program is developed and is used to obtain numerical results for the (1) free vibration, (2) nonlinearly deformed steady state, (3) free vibration about the nonlinearly deformed steady state, and (4) aeroelastic stability tasks. The numerical results obtained by the present method agree with results from other methods.

Murthy, V. R.↗

DESAP 2: A structural design program with stress and buckling constraints. Volume 1: Theoretical and user's manual

DESAP 2 is described as a finite element program for computer-automated, minimum weight design of elastic structures with constraints on stresses (including local instability criteria) and buckling loads. No limits are placed on the number of load conditions for stress-constrained design, but only one of these load conditions can be chosen as the potential buckling load. A substantial portion of DESAP 2, particularly the analysis of the prebuckling state, is derived from the SOLID SAP finite element program. The stress-constrained design is based on the classical stress ratio method, which drives the design towards a fully stressed state. The constraints on the buckling load are handled by solving the appropriate optimality criterion by successive iterations. During each iteration, the element sizes determined by the stress ratio method are used as the minimum size constraints. The element subroutines are organized in a manner that permits the user to make additions and changes with a minimal programming effort. Consequently, DESAP 2 can readily be changed into a special-purpose program to handle the user's specific design requirements and failure criteria.

Kiusalaas, J.↗

Precision Formation Delta-V Requirements for Distributed Platforms in Earth Orbit

Distributed spacecraft flying in formation can overcome the resolution limitations of monolithic, Earth-sensing systems. However, formation spacecraft must now expend fuel to counteract disturbances and the gravity gradients between spacecraft. We consider three different formation architectures and determine the (Delta)(nu) required to maintain relative positions at accuracies from 0.1 to 10 m (1(sigma)). The three architectures considered are: (i) Leader/Follower, in which individual spacecraft controllers track with respect to a passive, leader spacecraft, (ii) Center of Formation, in which individual spacecraft controllers track with respect to the geometric center of the formation, and (iii) Iterated Virtual Structure, in which a formation template is fit each timestep and individual spacecraft controllers track with respect to the fitted template.

formation flying↗

Mechanical Behavior and Analytical Modeling of Melt-Infiltrated SiC/SiC Woven Composite

The desirable properties in ceramic matrix composites (CMCs), such as high temperature strength, corrosion resistance, high toughness, low density, or good creep resistance have led to increased use of CMCs in high-speed engine structural components and structures that operate in extreme temperature and hostile aero-thermo-chemical environments. Ceramic matrix composites have been chosen for turbine material in the design of 21st century civil propulsion systems to achieve high fuel economy, improved reliability, extended life, and reduced cost. Most commercial CMCs are manufactured using a chemical vapor infiltration (CVI) process. However, a lower cost fabrication known as melt-infiltration process is also providing CMCs marked for use in hot sections of high-speed civil transports. Limited samples of a SiC/SiC melt-infiltrated woven composites are being investigated at room and elevated temperature below and above matrix cracking. These samples show graceful failure and toughness at room temperature with a reduction in strength and modulus at elevated temperatures. A generic finite element model is also being developed to predict monotonic and cyclic loading behavior of the woven composite. Use of the initial test data from the woven composite is being used for the development of the analytical model. This model is the first of a iterative process leading towards the development the model's capability to predict behavior at room and elevated temperature for monotonic and cyclic loading. The purpose of this paper is to report on the material and mechanical findings of the SiC/SiC melt-infiltrated woven composite and progress on the development of the finite element model.

Lang, J.↗

Microprocessor utilization in search and rescue missions

The position of an emergency transmitter may be determined by measuring the Doppler shift of the distress signal as received by an orbiting satellite. This requires the computation of an initial estimate and refinement of this estimate through an iterative, nonlinear, least squares estimation. A version of the algorithm was implemented and tested by locating a transmitter on the premises and obtaining observations from a satellite. The computer used was an IBM 360/95. The position was determined within the desired 10 km radius accuracy. The feasibility of performing the same task in real time using microprocessor technology, was determined. The least squares algorithm was implemented on an Intel 8080 microprocessor. The results indicate that a microprocessor can easily match the IBM implementation in accuracy and be performed inside the time limitations set.

Schwartz, M.↗

JWST Wavefront Control Toolbox

A Matlab-based toolbox has been developed for the wavefront control and optimization of segmented optical surfaces to correct for possible misalignments of James Webb Space Telescope (JWST) using influence functions. The toolbox employs both iterative and non-iterative methods to converge to an optimal solution by minimizing the cost function. The toolbox could be used in either of constrained and unconstrained optimizations. The control process involves 1 to 7 degrees-of-freedom perturbations per segment of primary mirror in addition to the 5 degrees of freedom of secondary mirror. The toolbox consists of a series of Matlab/Simulink functions and modules, developed based on a "wrapper" approach, that handles the interface and data flow between existing commercial optical modeling software packages such as Zemax and Code V. The limitations of the algorithm are dictated by the constraints of the moving parts in the mirrors.

Shin, Shahram Ron↗

Radioisotope Stirling Engine Powered Airship for Low Altitude Operation on Venus

The feasibility of a Stirling engine powered airship for the near surface exploration of Venus was evaluated. The heat source for the Stirling engine was limited to 10 general purpose heat source (GPHS) blocks. The baseline airship utilized hydrogen as the lifting gas and the electronics and payload were enclosed in a cooled insulated pressure vessel to maintain the internal temperature at 320 K and 1 Bar pressure. The propulsion system consisted of an electric motor driving a propeller. An analysis was set up to size the airship that could operate near the Venus surface based on the available thermal power. The atmospheric conditions on Venus were modeled and used in the analysis. The analysis was an iterative process between sizing the airship to carry a specified payload and the power required to operate the electronics, payload and cooling system as well as provide power to the propulsion system to overcome the drag on the airship. A baseline configuration was determined that could meet the power requirements and operate near the Venus surface. From this baseline design additional trades were made to see how other factors affected the design such as the internal temperature of the payload chamber and the flight altitude. In addition other lifting methods were evaluated such as an evacuated chamber, heated atmospheric gas and augmented heated lifting gas. However none of these methods proved viable.

Colozza, Anthony J.↗

Plume Impingement Software Module for Real-Time Proximity Operations

Successfully executing proximity operations in space, such as docking or in-orbit servicing, requires sophisticated spacecraft design that accounts for induced environments. As a chaser vehicle’s attitude control thrusters fire, they create rarefied plumes that can impact the target vehicle, with the potential to overload components, exceed thermal limits, and spin the target vehicle out of control. High-fidelity simulations of the thruster plume impingement environment require the direct simulation Monte Carlo (DSMC) method, but DSMC is too computationally expensive to simulate proximity operations that involve thousands of thruster firings. For this analysis to be tractable, engineering models of the plume flowfield and impingement events are used to simulate these trajectories [1]. Currently, on-orbit plume impingement environments are modeled through an inefficient open-loop analysis cycle where the vehicle’s flight controller and plume impingement teams iterate on the trajectories until they pass the target vehicle’s plume requirements. As complex on-orbit missions evolve and become more frequent, lengthy design cycles will become operational bottlenecks. To address this gap, this work develops an advanced plume impingement module capable of operating at real-time scale that can be integrated with existing mission planning tools and onboard flight systems. The plume module leverages state-of-the-art plume simulation techniques [2] to deliver fast, physics-based impingement predictions in a software architecture that can be tailored to diverse proximity operations scenarios. A prototype of this plume impingement module is built to demonstrate the feasibility of real-time performance. This prototype completes plume impingement calculations in microseconds per target geometry mesh point. The software serves as a foundational capability for plume-aware trajectory design, operational risk assessment, and future autonomous decision-making systems.

Plume Impingement↗

Application of direct solvers to unstructured meshes for the Euler and Navier-Stokes equations using upwind schemes

The application of Newton iteration to inviscid and viscous airfoil calculations on unstructured meshes is examined. A cell-centered finite volume scheme is employed on an unstructured mesh consisting of triangles. Roe's flux difference splitting scheme is used to compute the inviscid fluxes. Higher order accuracy is achieved by an interpolation procedure that makes use of auxiliary gradients. The efficient solution of the sparse linear system of equations which arises upon linearization in time is addressed. Results are presented for inviscid and viscous test cases. The complications which arise due to the introduction of nonlinear limiters are addressed.

Venkatakrishnan, V.↗

Comparative Analysis of Static and Dynamic Probabilistic Risk Assessment

Implementation of risk-informed design allows the design team to thoroughly explore the risks of a system while iterating the operations concept, design, and requirements until the system meets mission objects and is achievable within constraints. To arrive at a space system design that is likely to meet all constraints placed upon mass, cost, performance and risk, the system requirements must be understood and traded against each other as early as the conceptual design phase. Depending on the project phase and the goals of the risk analysis, various PRA methodologies could be used to produce quantitative risk estimates to enable such a process. In order to better understand the applicability, advantages, and limitations of various PRA methodologies, a comparative analysis of three bottom-up, component-based PRA approaches was performed. The three methods examined are a traditional static fault tree, a fault tree hybrid, and a dynamic Monte Carlo simulation. Each approach was used to assess a generic reaction control system (RCS) thruster pod and mission. The methods are assessed in terms of the process of modeling a system, the actionable information produced for the design team, and the overall fidelity of the quantitative risk evaluation generated. The paper also discusses the applicability of each methodology to the different phases of system development.

Probablistic↗

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗

Forty-Year Calibrated Record of Earth-Surface Reflected Radiance from Landsat: A Review

Sensors on Landsat satellites have been collecting images of the Earth's surface for nearly 40 years. These images have been invaluable for characterizing and detecting changes in the land cover and land use of the world. Although initially conceived as primarily picture generating sensors, even the early sensors were radiometrically calibrated and spectrally characterized prior to launch and incorporated some capabilities to monitor their radiometric calibration once on orbit. Recently, as the focus of studies has shifted to monitoring Earth surface parameters over significant periods of time, serious attention has been focused toward bringing the data from all these sensors onto a common radiometric scale over this 40-year period. This effort started with the most recent systems and then was extended back in time. Landsat-7 ETM+, the best-characterized sensor of the series prior to launch and once on orbit, and the most stable system to date, was chosen to serve as the reference. The Landsat-7 project was the first of the series to build an image assessment system into its ground system, allowing systematic characterization of its sensors and data. Second, the Landsat-5 TM (still operating at the time of the Landsat-7 launch and continues to operate) calibration history was reconstructed based on its internal calibrator, vicarious calibrations, pseudo-invariant sites and a tie to Landsat-7 ETM+ at the time of the commissioning of Landsat-7. This process was performed in two iterations: the earlier one relied primarily on the TM internal calibrator. When this was found to have some deficiencies, a revised calibration was based more on pseudo-invariant sites, though the internal calibrator was still used to establish the short-term variations in response due to icing build up on the cold focal plane. As time progressed, a capability to monitor the Landsat-5 TM was added to the image assessment system. The Landsat-4 TM, which operated from 1982-1992, was the third system to which the radiometric scale was extended. The limited and broken use of the Landsat-4 TM made this analysis more difficult. Eight-day separated image pairs from Landsat-5 combined with analysis of pseudo invariant sites established this history. The fourth and most challenging effort was making the Landsat-1 to -5 MSS sensors' data internally radiometrically consistent. This effort was particularly complicated by the age of the MSS data, varying formats and processing levels in the archive, limited datasets, and limited documentation available. Ultimately, pseudo-invariant sites were identified in North America and used for this effort. Note that most of the Landsat-MSS archived data had already been calibrated using the MSS internal calibrators, so this processing was imbedded in the result. The final effort was developing an absolute scale for Landsat MSS similar to what was already established for the "TM" sensors. This was accomplished by using simultaneous data from Landsat-5 MSS and Landsat-5 TM, accounting for spectral differences between the sensors using EO-1 Hyperion data. The recalibrated history of the Landsat data and implications to users are discussed. The key result from this work is a consistently calibrated Landsat data archive that spans nearly 40 years with total uncertainties on the order of 10% or less for most sensors and bands.

Markham, Brian↗

Synthetic Failure Mode Generation for Resilience Analysis and Failure Mechanism Discovery

Traditional risk-based design processes seek to mitigate operational hazards by manually identifying possible faults and corresponding mitigation strategies—a tedious process which critically relies on the designer’s limited knowledge. Resilience-based design, on the other hand, seeks to embody generic hazard-mitigating properties in the system to mitigate unknown hazards, often by modelling the system's response to potential hazardous events. This work adapts this approach to the traditional risk-based design process to synthetically generate hazardous modes, by representing them as a unique combination of internal component health-states which can then be injected and simulated in a model of the system failure dynamics. The design process may then reduce the risk of unknown internal hazards by iteratively mitigating the effects of these modes. The performance of this approach is evaluated in a model of an autonomous rover, where cluster analysis shows that elaborating the space of synthetic faults in the drive system using this approach uncovers a wider range of possible hazardous trajectories and failure consequences within each trajectory. However, this increase in hazard information comes at a high computational expense, highlighting the need for advanced, efficient methods to search and sample the hazard space.

Simulation↗

Synthetic Failure Mode Generation for Resilience Analysis and Failure Mechanism Discovery

Traditional risk-based design processes seek to mitigate operational hazards by manually identifying possible faults and corresponding mitigation strategies—a tedious process which critically relies on the designer’s limited knowledge. Resilience-based design, on the other hand, seeks to embody generic hazard-mitigating properties in the system to mitigate unknown hazards, often by modelling the system's response to potential hazardous events. This work adapts this approach to the traditional risk-based design process to synthetically generate hazardous modes, by representing them as a unique combination of internal component health-states which can then be injected and simulated in a model of the system failure dynamics. The design process may then reduce the risk of unknown internal hazards by iteratively mitigating the effects of these modes. The performance of this approach is evaluated in a model of an autonomous rover, where cluster analysis shows that elaborating the space of synthetic faults in the drive system using this approach uncovers a wider range of possible hazardous trajectories and failure consequences within each trajectory. However, this increase in hazard information comes at a high computational expense, highlighting the need for advanced, efficient methods to search and sample the hazard space.

Simulation↗