Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INDIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Effect of thermal processing on silver thin films of varying thickness deposited on zinc oxide and indium tin oxide

Silver films of varying thicknesses (25, 45, and 60 nm) were deposited on indium tin oxide (ITO) on silicon and zinc oxide (ZnO) on silicon. The films were annealed in vacuum for 1 h at different temperatures (300-650 deg. C). Four-point-probe measurements were used to determine the resistivity of the films. All films showed an abrupt change in resistivity beyond an onset temperature that varied with thickness. Rutherford backscattering spectrometry measurements revealed agglomeration of the Ag films upon annealing as being responsible for the resistivity change. X-ray pole figure analysis determined that the annealed films took on a preferential <111> texturing; however, the degree of texturing was significantly higher in Ag/ZnO/Si than in Ag/ITO/Si samples. This observation was accounted for by interface energy minimization. Atomic force microscopy (AFM) measurements revealed an increasing surface roughness of the annealed films with temperature. The resistivity behavior was explained by the counterbalancing effects of increasing crystallinity and surface roughness. Average surface roughness obtained from the AFM measurements were also used to model the agglomeration of Ag based on Ostwald ripening theory.

36 MATERIALS SCIENCE↗

Electrical stress-induced instability of amorphous indium-gallium-zinc oxide thin-film transistors under bipolar ac stress

Bipolar ac stress-induced instability of amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors is comparatively investigated with that under a positive dc gate bias stress. While the positive dc gate bias stress-induced threshold voltage shift ({delta}V{sub T}) is caused by the charge trapping into the interface/gate dielectric as reported in previous works, the dominant mechanism of the ac stress-induced {delta}V{sub T} is observed to be due to the increase in the acceptorlike deep states of the density of states (DOS) in the a-IGZO active layer. Furthermore, it is found that the variation of deep states in the DOS makes a parallel shift in the I{sub DS}-V{sub GS} curve with an insignificant change in the subthreshold slope, as well as the deformation of the C{sub G}-V{sub G} curves.

36 MATERIALS SCIENCE↗

Microporous SiO{sub 2} with huge electric-double-layer capacitance for low-voltage indium tin oxide thin-film transistors

Electric-double-layer (EDL) effect is observed in microporous SiO{sub 2} dielectric films deposited at room temperature by plasma-enhanced chemical vapor deposition method. Indium tin oxide thin-film transistors gated by such microporous SiO{sub 2} gate dielectric are fabricated at room temperature, and a low operating voltage of 1.5 V is obtained due to the huge EDL specific capacitance (2.14 {mu}F/cm{sup 2}). The field-effect electron mobility is estimated to be 118 cm{sup 2} V{sup -1} s{sup -1}. Current on/off ratio and subthreshold gate voltage swing are estimated to be 5x10{sup 6} and 92 mV/decade, respectively. Room-temperature deposited microporous SiO{sub 2} dielectric is promising for low-power field-effect transistors on temperature sensitive substrates.

36 MATERIALS SCIENCE↗

Formation and evolution of self-organized Au nanorings on indium-tin-oxide surface

This work reports on the formation of Au nanoclusters and on their evolution in nanoring structures on indium-tin-oxide surface by sputtering deposition and annealing processes. The quantification of the characteristics of the nanorings (surface density, depth, height, and width) is performed by atomic force microscopy. The possibility to control these characteristics by tuning annealing temperature and time is demonstrated establishing relations which allow to set the process parameters to obtain nanostructures of desired morphological properties for various technological applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Manganese-doped indium oxide and its application in organic light-emitting diodes

Thin films of manganese-doped indium oxide (IMO) deposited by electron beam evaporation have been investigated as anodes in organic light-emitting diodes (OLEDs). The IMO films have a high work function of 5.35 eV, a desirable surface morphology with an average roughness of 1.1 nm, a high average optical transmittance of 87.2% in the visible region, and a maximum optical transmittance of 92% at 460 nm. It is demonstrated that an IMO anode can effectively improve hole injection at the anode/organic interface, resulting in OLEDs with an increased electroluminescent efficiency.

36 MATERIALS SCIENCE↗

Highest transmittance and high-mobility amorphous indium gallium zinc oxide films on flexible substrate by room-temperature deposition and post-deposition anneals

Amorphous indium gallium zinc oxide (a-IGZO) thin films of the highest transmittance reported in literature were initially deposited onto flexible polymer substrates at room temperature. The films were annealed in vacuum, air, and oxygen to enhance their electrical and optical performances. Electrical and optical characterizations were done before and after anneals. A partial reversal of the degradation in electrical properties upon annealing in oxygen was achieved by subjecting the films to subsequent vacuum anneals. A model was developed based on film texture and structural defects which showed close agreement between the measured and calculated carrier mobility values at low carrier concentrations (2-6 x 10{sup 19} cm{sup -3}).

36 MATERIALS SCIENCE↗

Indium-tin-oxide-free tris(8-hydroxyquinoline) Al organic light-emitting diodes with 80% enhanced power efficiency

Efficient indium tin oxide (ITO)-free small molecule organic light-emitting diodes (SMOLEDs) with multilayered highly conductive poly(3,4-ethylenedioxy thiophene):poly(styrenesulfonate) (PEDOT:PSS) as the anode are demonstrated. PEDOT:PSS/MoO{sub 3}/N,N'-diphenyl- N,N'-bis(1-naphthylphenyl)-1,1'-biphenyl-4,4'-diamine (NPD)/tris(8-hydroxyquinoline) Al (Alq{sub 3})/4,7-diphenyl-1,10-phenanthroline (BPhen)/LiF/Al SMOLEDs exhibited a peak power efficiency of 3.82 lm/W, 81% higher than that of similar ITO-based SMOLEDs (2.11 lm/W). The improved performance is believed to be due to the higher work function, lower refractive index, and decreased surface roughness of PEDOT:PSS vs ITO, and to Ohmic hole injection from PEDOT:PSS to the NPD layer via the MoO{sub 3} interlayer. The results demonstrate that PEDOT:PSS can substitute ITO in SMOLEDs with strongly improved device performance.

14 SOLAR ENERGY↗

Electronic states at the interface between indium tin oxide and silicon

Electronic properties and thermal stability of interfacial states between indium tin oxide (ITO) and monocrystalline silicon (Si) have been investigated. ITO films with thicknesses of about 300 nm were deposited by dc magnetron sputtering on n- and p-type (100) Si at room temperature. The samples were then annealed for 30 min at different temperatures in the range 100-600 deg. C, and the ITO-Si junction was found to exhibit rectifying behavior. Current-voltage (IV), capacitance-voltage (CV), and deep-level transient spectroscopy (DLTS) measurements have been used to electrically characterize the ITO-Si interface. DLTS measurements on p-type Si samples reveal a dominant hole trap at around 0.37 eV above the valence band edge. In the n-type samples, a broad band of electron traps occur in the range 0.1-0.2 eV below the conduction band edge. These electron traps display wide DLTS peaks, indicating a band of electronic energy levels rather than well-defined states originating from isolated point defects. All the traps in both the p- and n-type samples are found to be located near the ITO-Si interface. Investigations of the thermal stability of the observed electronic states show that the dominant hole trap anneal out after 30 min at 250 deg. C, while the dominant electron traps can be stable up to 500 deg. C. IV and DLTS measurements demonstrate a clear correlation between the annealing of the dominant electronic states and increase in the junction rectification.

36 MATERIALS SCIENCE↗

The electronic structure of co-sputtered zinc indium tin oxide thin films

Zinc indium tin oxide (ZITO) transparent conductive oxide layers were deposited via radio frequency (RF) magnetron co-sputtering at room temperature. A series of samples with gradually varying zinc content was investigated. The samples were characterized with x-ray and ultraviolet photoemission spectroscopy (XPS, UPS) to determine the electronic structure of the surface. Valence and conduction bands maxima (VBM, CBM), and work function were determined. The experiments indicate that increasing Zn content results in films with a higher defect rate at the surface leading to the formation of a degenerately doped surface layer if the Zn content surpasses {approx}50%. Furthermore, the experiments demonstrate that ZITO is susceptible to ultraviolet light induced work function reduction, similar to what was earlier observed on ITO and TiO{sub 2} films.

36 MATERIALS SCIENCE↗

Thickness effect on laser-induced-damage threshold of indium-tin oxide films at 1064 nm

Laser-induced-damage characteristics of commercial indium-tin oxide (ITO) films deposited by DC magnetron sputtering deposition on K9 glass substrates as a function of the film thickness have been studied at 1064 nm with a 10 ns laser pulse in the 1-on-1 mode, and the various mechanisms for thickness effect on laser-induced-damage threshold (LIDT) of the film have been discussed in detail. It is observed that laser-damage-resistance of ITO film shows dramatic thickness effect with the LIDT of the 50-nm ITO film 7.6 times as large as the value of 300 nm film, and the effect of depressed carrier density by decreasing the film thickness is demonstrated to be the primary reason. Our experiment findings indicate that searching transparent conductive oxide (TCO) film with low carrier density and high carrier mobility is an efficient technique to improve the laser-damage-resistance of TCO films based on maintaining their well electric conductivity.

36 MATERIALS SCIENCE↗

Transmission electron microscopy of the amorphization of copper indium diselenide by in situ ion irradiation

Copper indium diselenide (CIS), along with its derivatives Cu(In,Ga)(Se,S){sub 2}, is a prime candidate for use in the absorber layers of photovoltaic devices. Due to its ability to resist radiation damage, it is particularly well suited for use in extraterrestrial and other irradiating environments. However, the nature of its radiation hardness is not well understood. In this study, transmission electron microscopy (TEM) with in situ ion irradiation was used to monitor the dynamic microstructural effects of radiation damage on CIS. Samples were bombarded with 400 keV xenon ions to create large numbers of atomic displacements within the thickness of the TEM samples and thus explore the conditions under which, if any, CIS could be amorphized. By observing the impact of heavily damaging radiation in situ--rather than merely the end-state possible in ex situ experiments--at the magnifications allowed by TEM, it was possible to gain an understanding of the atomistic processes at work and the underlying mechanism that give rise to the radiation hardness of CIS. At 200 K and below, it was found that copper-poor samples could be amorphized and copper-rich samples could not. This difference in behavior is linked to the crystallographic phases that are present at different compositions. Amorphization was found to progress via a combination of one- and two-hit processes. The radiation hardness of CIS is discussed in terms of crystallographic structures/defects and the consequences these have for the ability of the material to recover from the effects of displacing radiation.

36 MATERIALS SCIENCE↗

Reversible wettability of electron-beam deposited indium-tin-oxide driven by ns-UV irradiation

Indium tin oxide (ITO) is one of the most widely used semiconductor oxides in the field of organic optoelectronics, especially for the realization of anode contacts. Here the authors report on the control of the wettability properties of ITO films deposited by reactive electron beam deposition and irradiated by means of nanosecond-pulsed UV irradiation. The enhancement of the surface water wettability, with a reduction of the water contact angle larger than 50 deg., is achieved by few tens of seconds of irradiation. The analyzed photo-induced wettability change is fully reversible in agreement with a surface-defect model, and it can be exploited to realize optically transparent, conductive surfaces with controllable wetting properties for sensors and microfluidic circuits.

36 MATERIALS SCIENCE↗

Low frequency pressure modulation of indium antimonide

A lumped parameter resonator capable of generating megapascal pressures at low frequency (kilohertz) is described. Accelerometers are used to determine the applied pressure, and are calibrated with a piezoelectric sample. A laser diagnostic was also developed to measure the pressure in semiconductor samples through the band gap pressure dependence. In addition, the laser diagnostic has been used to measure the attenuation coefficient {alpha} of commercially available indium antimonide (InSb) wafers. The resonator and laser diagnostic have been used with InSb samples to verify the pressure response.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Origin of ferromagnetism enhancement in bi-layer chromium-doped indium zinc oxides

This work demonstrates that by controlling the rapid thermal annealing temperature, amorphous chromium-doped indium zinc oxide films develop an amorphous-crystalline bi-layer structure and show magnetization up to {approx}30 emu/cm{sup 3}. The crystalline layer arises from significant out-diffusion of Zn from surfaces, leading to a large difference in the Zn:In ratio in amorphous and crystalline layers. Doped Cr ions in amorphous and crystalline layers form different valence configurations, creating a charge reservoir which transfers electrons through amorphous-crystalline interfaces and in turn enhances ferromagnetism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrical effect of titanium diffusion on amorphous indium gallium zinc oxide

In this work, thermal diffusion phenomenon of Ti into amorphous indium gallium zinc oxide ({alpha}-IGZO) was carefully investigated with secondary ion mass spectroscopy, I-V, and R{sub s} measurement systems and HSC chemistry simulation tool. According to the experimental and simulated results, the diffused Ti atoms were easily oxidized due to its lowest oxidation free energy. Since oxygen atoms were decomposed from the {alpha}-IGZO during the oxidation of Ti, the number of oxygen vacancies working as electron-donating sites in {alpha}-IGZO was dramatically increased, contributing to the decrease of resistivity ({rho}) from 1.96 {Omega} cm (as-deposited {alpha}-IGZO) to 1.33 Multiplication-Sign 10{sup -3}{Omega} cm (350 Degree-Sign C annealed {alpha}-IGZO).

36 MATERIALS SCIENCE↗

A comparison of ZnO films deposited on indium tin oxide and soda lime glass under identical conditions

ZnO films have been grown via a vapour phase transport (VPT) on soda lime glass (SLG) and indium-tin oxide (ITO) coated glass. ZnO film on ITO had traces of Zn and C which gives them a dark appearance while that appears yellowish-white on SLG. X-ray photoelectron spectroscopy studies confirm the traces of C in the form of C-O. The photoluminescence studies reveal a prominent green luminescence band for ZnO film on ITO.

36 MATERIALS SCIENCE↗

Highly flexible, hybrid-structured indium tin oxides for transparent electrodes on polymer substrates

We developed highly flexible, hybrid-structured crystalline indium tin oxide (ITO) for use as transparent electrodes on polymer substrates by embedding Ag nanoparticles (AgNPs) into the substrate. The hybrid ITO consists of domains in one orientation grown on the AgNPs and a matrix of the other orientation. The domains are stronger than the matrix and function as barriers to crack propagation. As a result, both the critical bending radius (r{sub c}) (under which the resistivity change ({Delta}{rho}) is less than a given value) and the change in {Delta}{rho} with decreasing r significantly decreased in the hybrid ITO compared with homogenous ITO.

36 MATERIALS SCIENCE↗

In situ analyses on negative ions in the indium-gallium-zinc oxide sputtering process

The origin of negative ions in the dc magnetron sputtering process using a ceramic indium-gallium-zinc oxide target has been investigated by in situ analyses. The observed negative ions are mainly O{sup -} with energies corresponding to the target voltage, which originates from the target and barely from the reactive gas (O{sub 2}). Dissociation of ZnO{sup -}, GaO{sup -}, ZnO{sub 2}{sup -}, and GaO{sub 2}{sup -} radicals also contributes to the total negative ion flux. Furthermore, we find that some sputtering parameters, such as the type of sputtering gas (Ar or Kr), sputtering power, total gas pressure, and magnetic field strength at the target surface, can be used to control the energy distribution of the O{sup -} ion flux.

36 MATERIALS SCIENCE↗