Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HOLE MOBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Molecular-level architectural design using benzothiadiazole-based polymers for photovoltaic applications

A series of low band gap, planar conjugated polymers, P1 (PFDTBT), P2 (PFDTDFBT) and P3 (PFDTTBT), based on fluorene and benzothiadiazole, was synthesized. The effect of fluorine substitution and fused aromatic spacers on the optoelectronic and photovoltaic performance was studied. The polymer, derived from dithienylated benzothiodiazole and fluorene, P1 , exhibited a highest occupied molecular orbital (HOMO) energy level at -5.48 eV. Density functional theory (DFT) studies as well as experimental measurements suggested that upon substitution of the acceptor with fluorine, both the HOMO and lowest unoccupied molecular orbital (LUMO) energy levels of the resulting polymer, P2 , were lowered, leading to a higher open circuit voltage and short circuit current with an overall improvement of more than 110% for the photovoltaic devices. Moreover, a decrease in the torsion angle between the units was also observed for the fluorinated polymer P2 due to the enhanced electrostatic interaction between the fluorine substituents and sulfur atoms, leading to a high hole mobility. The use of a fused π-bridge in polymer P3 for the enhancement of the planarity as compared to the P1 backbone was also studied. This enhanced planarity led to the highest observed mobility among the reported three polymers as well as to an improvement in the device efficiency by more than 40% for P3 .

Chemistry↗

Growth of silicon ribbon by edge-defined, film-fed growth

Recent advances in the application of the edge-defined, film-fed growth (EFG) method to silicon ribbon are described. Ribbons up to 2 x 40 cm and 1 x 70 cm in width and length, respectively, have been grown at rates of 1 to 2.5 cm/min. The electrical properties of typical undoped ribbons are resistivity of 0.5 to 5 ohm-cm p-type, and hole mobility of 200 to 350 sq cm/V-sec. Ribbon growth speeds are consistent with the use of EFG silicon for terrestrial power.

Bates, H. E.↗

Thickness dependences of solar cell performance

The significance of including factors such as the base resistivity loss for solar cells thicker than 100 microns and emitter and BSF layer recombination for thin cells in predicting the fill factor and efficiency of solar cells is demonstrated analytically. A model for a solar cell is devised with the inclusion of the dopant impurity concentration profile, variation of the electron and hole mobility with dopant concentration, the concentration and thermal capture and emission rates of the recombination center, device temperature, the AM1 spectra and the Si absorption coefficient. Device equations were solved by means of the transmission line technique. The analytical results were compared with those of low-level theory for cell performance. Significant differences in predictions of the fill factor resulted, and inaccuracies in the low-level approximations are discussed.

Sah, C. T.↗

Analysis of defect structure in silicon. Characterization of SEMIX material. Silicon sheet growth development for the large area silicon sheet task of the low-cost solar array project

Statistically significant quantitative structural imperfection measurements were made on samples from ubiquitous crystalline process (UCP) Ingot 5848 - 13C. Important correlation was obtained between defect densities, cell efficiency, and diffusion length. Grain boundary substructure displayed a strong influence on the conversion efficiency of solar cells from Semix material. Quantitative microscopy measurements gave statistically significant information compared to other microanalytical techniques. A surface preparation technique to obtain proper contrast of structural defects suitable for quantimet quantitative image analyzer (QTM) analysis was perfected and is used routinely. The relationships between hole mobility and grain boundary density was determined. Mobility was measured using the van der Pauw technique, and grain boundary density was measured using quantitative microscopy technique. Mobility was found to decrease with increasing grain boundary density.

Natesh, R.↗

Advanced methods for preparation and characterization of infrared detector materials

Crystals were prepared by the Bridgman-Stockbarger method with a wide range of crystal growth rates and temperature gradients adequate to prevent constitutional supercooling under diffusion-limited, steady-state, growth conditions. The longitudinal compositional gradients for different growth conditions and alloy compositions were calculated and compared with experimental data to develop a quantitative model of solute redistribution during the crystal growth of the alloys. Measurements were performed to ascertain the effect of growth conditions on radial compositional gradients. The pseudobinary HgTe-CdTe constitutional phase diagram was determined by precision differential-thermal-analysis measurements and used to calculate the segregation coefficient of Cd as a function of x and interface temperature. Experiments were conducted to determine the ternary phase equilibria in selected regions of the Hg-Cd-Te constitutional phase diagram. Electron and hole mobilities as functions of temperature were analyzed to establish charge-carrier scattering probabilities. Computer algorithms specific to Hg(1-x)CdxTe were developed for calculations of the charge-carrier concentration, charge-carrier mobilities, Hall coefficient, and Dermi Fermi energy as functions of x, temperature, ionized donor and acceptor concentrations, and neutral defect concentrations.

Broerman, J. G.↗

Surface and allied studies in silicon solar cells

Two main results are presented. The first deals with a simple method that determines the minority-carrier lifetime and the effective surface recombination velocity of the quasi-neutral base of silicon solar cells. The method requires the observation of only a single transient, and is amenable to automation for in-process monitoring in manufacturing. This method, which is called short-circuit current decay, avoids distortion in the observed transient and consequent inacccuracies that arise from the presence of mobile holes and electrons stored in the p/n junction spacecharge region at the initial instant of the transient. The second main result consists in a formulation of the relevant boundary-value problems that resembles that used in linear two-port network theory. This formulation enables comparisons to be made among various contending methods for measuring material parameters of p/n junction devices, and enables the option of putting the description in the time domain of the transient studies in the form of an infinite series, although closed-form solutions are also possible.

Lindholm, F. A.↗

Growth of high-quality thin-film Ge single crystals by plasma-enhanced chemical vapor deposition

Thin-film Ge single crystals (approx. 10 microns) have been epitaxially grown on polished NaCl(100) substrates at 450C by using plasma-enhanced chemical vapor deposition. Films on approximately 1 sq cm and larger were separated from the NaCl by either melting the salt or by differential shear stress upon cooling to room temperature. The ordered growth of the Ge was found to be most sensitive to the initial plasma power and to the continuum flow dynamics within the carbon susceptor. The films were visually specular and exhibited a high degree of crysalline order when examined by X-ray diffraction. The films were found to be p-type with a carrier concentration of approximately 3 x 10 to the 16th power/cu cm, a resistivity of 0.11 ohm-cm, and a Hall hole mobility of 1820 sq cm/v/s at room temperature. Vacuum firing minimized the primary contaminant, Na, and corresponding lowered the carrier concentration to 4 x 10 to the 14th power/cu cm.

Outlaw, R. A.↗

Electronic and transport properties of HgCdTe and HgZnTe

Band structures are calculated for HgTe, CdTe, and ZnTe. A near band-edge approximation to the coherent potential approximation is used to compute the alloy band-gap variation and electron and hole effective masses in HgZnTe and HgCdTe. Both diagonal and off-diagonal disorder are included. The consequences for hole mobility are found to be significant if anion disorder is present because of a valence-band offset.

Berding, M. A.↗

MBE HgCdTe heterostructure detectors

HgCdTe has been the mainstay for medium (3 to 5 micron) and long (10 to 14 micron) wavelength infrared detectors in recent years. Conventional growth and processing techniques are continuing to improve the material. However, the additional ability to tailor composition and placement of doped layers on the tens of angstroms scale using molecular beam epitaxy (MBE) provides the opportunity for new device physics and concepts to be utilized. MBE-based device structures to be discussed here can be grouped into two categories: tailored conventional structures and quantum structures. The tailored conventional structures are improvements on familiar devices, but make use of the ability to create layers of varying composition, and thus band gap, at will. The heterostructure junction can be positioned independently of doping p-n junctions. This allows the small band gap region in which the absorption occurs to be separated from a larger band gap region in which the electric field is large and where unwanted tunneling can occur. Data from hybrid MBE/liquid phase epitaxy (LPE)/bulk structures are given. Quantum structures include the HgTe-CdTe superlattice, in which the band gap and transport can be controlled by alternating thin layers (tens of angstroms thick) of HgTe and CdTe. The superlattice has been shown to exhibit behavior which is non-alloy like, including very high hole mobilities, two-dimensional structure in the absorption coefficient, resonant tunneling, and anisotropic transport.

Schulman, Joel N.↗

The Effect of Strain on the Base Resistance and Transit Time of Ungraded and Compositional-Graded SiGe HBTs

A theoretical study of the effects of the strain on the base properties of ungraded and compositional-graded n-p-n SiGe Heterojunction Bipolar Transistors (HBT) is presented. The dependencies of the transverse hole mobility and longitudinal electron mobility upon strain, composition and doping, are formulated using published Monte-Carlo data and, consequently, the base resistance and transit time are modeled and calculated. The results are compared to results obtained using common formulas that ignore these dependencies. The differences between the two sets of results are shown. The paper's conclusion is that for the design, analysis and optimization of high frequency SiGe HBTs the strain effects on the base properties cannot be ignored.

Rosenfeld, D.↗

Fabrication and Electronic Properties of CZTSe

To solve the open circuit voltage limitation in Cu2ZnSn(SSe)4 further understanding of defects and the fundamental properties of the bulk material are needed. Although there are a number of literature reports of single crystals, the vast majority are made with a flux agent such as iodine which could potentially act as a dopant or affect defect properties in the material. In this report 2-5 mm single crystals of CZTSe of different compositions were achieved by solid state reaction of elements in a sealed ampoule below the melt temperature without a flux agent. The bulk composition of single crystals are compared to electronic and opto-electronic properties from Hall and photoluminescence (PL) measurements. Intergrain measurements showed record hole mobilities for pure CZTSe in excess of 100 cm2/Vs. PL intensity and uniformity were improved by removing inhomogeneities and surface phases through crystal polishing, followed by Br-methanol etching to remove polishing damage. Despite processing conditions more favorable to equilibrium crystal conditions, a broad PL peak is observed with significant luminescence below the band-gap similar to literature reports of band-tailing. A more detailed publication of results and further experiments will be reported in an upcoming Journal of Photovoltaics.

Bishop, Douglas M.↗

Squeezing clathrate cages to host trivalent rare-earth guests

Strike difference of the trivalent rare-earth cations from their alkali and alkaline-earth peers is in the presence of localized 4f-electrons and strong spin-orbit coupling. Placing trivalent rare-earth cations inside the fullerene molecules or in between the blocks of itinerant magnetic intermetallics gave rise to plethora of fascinating properties and materials. A long-time missing but hardly desired piece is the semiconducting or metallic compound where rare-earth cations are situated inside the oversized polyhedral cages of three-dimensional framework. In this work we present a synthesis of such compounds, rare-earth containing clathrates Ba 8-x R x Cu 16 P 30 . The unambiguous proofs of their composition and crystal structure were achieved by a combination of synchrotron powder diffraction, time-of-flight neutron powder diffraction, scanning-transmission electron microscopy, and electron energy-loss spectroscopy. Our quantum-mechanical calculations and experimental characterizations show that the incorporation of the rare-earth cations significantly enhances the hole mobility and concentration which results in the drastic increase in the thermoelectric performance.

36 MATERIALS SCIENCE↗

Ionization equilibrium at the transition from valence-band to acceptor-band migration of holes in boron-doped diamond

A quasi-classical model of ionization equilibrium in the p-type diamond between hydrogen-like acceptors (boron atoms which substitute carbon atoms in the crystal lattice) and holes in the valence band (v-band) is proposed. The model is applicable on the insulator side of the insulator–metal concentration phase transition (Mott transition) in p-Dia:B crystals. The densities of the spatial distributions of impurity atoms (acceptors and donors) and of holes in the crystal are considered to be Poissonian, and the fluctuations of their electrostatic potential energy are considered to be Gaussian. The model accounts for the decrease in thermal ionization energy of boron atoms with increasing concentration, as well as for electrostatic fluctuations due to the Coulomb interaction limited to two nearest point charges (impurity ions and holes). The mobility edge of holes in the v-band is assumed to be equal to the sum of the threshold energy for diffusion percolation and the exchange energy of the holes. On the basis of the virial theorem, the temperature T{sub j} is determined, in the vicinity of which the dc band-like conductivity of holes in the v-band is approximately equal to the hopping conductivity of holes via the boron atoms. For compensation ratio (hydrogen-like donor to acceptor concentration ratio) K ≈ 0.15 and temperature T{sub j}, the concentration of “free” holes in the v-band and their jumping (turbulent) drift mobility are calculated. Dependence of the differential energy of thermal ionization of boron atoms (at the temperature 3T{sub j}/2) as a function of their concentration N is calculated. The estimates of the extrapolated into the temperature region close to T{sub j} hopping drift mobility of holes hopping from the boron atoms in the charge states (0) to the boron atoms in the charge states (−1) are given. Calculations based on the model show good agreement with electrical conductivity and Hall effect measurements for p-type diamond with boron atom concentrations in the range from 3 × 10{sup 17} to 3 × 10{sup 20 }cm{sup −3}, i.e., up to the Mott transition. The model uses no fitting parameters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Final report on LDRD: MBE growth and transport properties of carbon-doped high mobility two-dimensional hole systems

Utilizing a new high mobility Ga As growth facility at the Birck Nanotechno logy Center (BNC) at Purdue University, a systematic investigation of molecular beam epitaxy (MBE) growth of carbon-doped high mobility two-dimensional hole systems (2DHS) was performed. New physics and new device applications often follow from advances in material synthesis. The recent development of efficient resistive carbon doping filaments allow for the construction of extremely high quality two dimensional hole systems on the high symmetry (100) face of GaAs. The initial studies focused on determining the parameters that presently limit low temperature mobility in carbon-doped 2DHS. The work included MBE growth, structure modeling, and low temperature transport measurement of MBE grown samples.

Reno, John Louis↗

Defect chemistry and high-temperature transport in SrFe{sub 1−x}Sn{sub x}O{sub 3–δ}

The electrical conductivity of SrFe{sub 1–x}Sn{sub x}O{sub 3–δ} (x=0.05, 0.10, 017) was measured by a four-probe dc technique in the partial oxygen pressure range of 10{sup –18}–0.5 atm at temperatures between 800 °Ð ÐŽ and 950 °Ð ÐŽ. The oxygen content in these oxides was measured under the same ambient conditions by means of coulometric titration. The thermodynamic analysis of oxygen nonstoichiometry data was carried out to determine the equilibrium constants for defect-formation reactions and to calculate the concentrations of ion and electron charge carriers. The partial contributions of oxygen ions, electrons and holes to charge transport were assessed, and the mobility of respective carriers was evaluated by an integral examination of the electrical conductivity and oxygen nonstoichiometry data. It has been found that the mobility of holes in SrFe{sub 1−x}Sn{sub x}O{sub 3−δ} varies in the range of ~0.005–0.04 cm{sup 2} V{sup −1} s{sup −1}, linearly increasing with the oxygen content and decreasing with increased tin concentration. The mobility of electron carriers was shown to be independent of the oxygen content. The average migration energy of an electron was estimated to be ~0.45 eV, with that of a hole being ~0.3 eV. - Highlights: • The conductivity and oxygen nonstoichiometry in SrFe{sub 1−x}Sn{sub x}O{sub 3−δ} were measured. • Tin substitution was found to affect insignificantly defect formation reactions. • The hole mobility was found to increase linearly with the oxygen content. • The hole mobility was found to be much higher than the electron mobility.

36 MATERIALS SCIENCE↗

Hole Trapping at Surfaces of m-ZrO 2 and m-HfO 2 Nanocrystals

We investigate hole trapping at the most prevalent facets of monoclinic zirconia (m-ZrO 2 ) and hafnia (m-HfO 2 ) nanocrystals using first-principles methods. The localization of holes at surface oxygen ions is more favorable than in the bulk crystal by up to ~1 eV. This is caused mainly by the reduction of the absolute value of the electrostatic potential at the surface ions with respect to the bulk and by the significant surface distortion caused by the hole localization. The mobility of holes at surfaces is much lower than that found in the bulk and is fairly isotropic. Unlike in cubic oxides, such as MgO and CaO, we do not find a significant driving force for preferential trapping of holes at steps on the m-ZrO 2 surface. These fundamental results are relevant to mechanisms of water oxidation, photocatalysis, contact charging, and photodesorption.

Environmental Molecular Sciences Laboratory↗

Highly mobile oxygen hole-type charge carriers in fused silica

Some peculiar positive charge carriers are thermally generated in fused silica above 500 C. These charge carriers appear to be positive holes, chemically O-states, probably arising from dissociation of peroxy defects. The charge carriers give rise to a pronounced positive surface charge which disappears upon cooling but can be quenched by rapid quenching from about 800 C. Reheating to 200 C remobilizes these charge carriers and causes them to anneal below 400 C. The generation of positive holes charge carriers may be important to understand failure mechanisms of SiO2 insulators.

Freund, Friedemann↗