Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HARDENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Prediction of water vapour sorption isotherms and microstructure of hardened Portland cement pastes

Water vapour sorption isotherms of cementitious materials reflect the multi-scale physical microstructure through its interaction with moisture. Our ability to understand and predict adsorption and desorption behaviour is essential in the application of modern performance-based approaches to durability analysis, along with many other areas of hygro-mechanical and hygro-chemo-mechanical behaviour. In this paper, a new physically based model for predicting water vapour sorption isotherms of arbitrary hardened Portland cement pastes is presented. Established thermodynamic principles, applied to a microstructure model that develops with hydration, provide a rational basis for predictions. Closed-form differentiable equations, along with a rational consideration of hysteresis and scanning phenomena, makes the model suitable for use in numerical moisture simulations. The microstructure model is reconciled with recently published {sup 1}H NMR and mercury intrusion porosimetry results.

36 MATERIALS SCIENCE↗

Time-dependent water vapor desorption isotherm model of hardened cement paste

Highlights: • Short-term and long-term desorption isotherms of hardened cement paste are reviewed. • Water content at RH depends on both thermodynamic and microstructural equilibria. • An extended GAB equation is proposed to fit the cavitation drop during desorption. • A dynamic time-dependent sorption isotherm model is shown and used for simulations. • Numerical results capture anomalous drying in the same RH as seen experimentally. This study aims to enhance moisture transport modeling by elucidating the so-called anomalous water diffusion in cementitious materials. Water desorption isotherms are measured from samples at various drying stages using techniques with different durations to quantify the impact of the drying duration on the water sorption ability. A single water sorption isotherm does not solely give a relationship between the water content and relative humidity but also represents the state of microstructure. The continuous evolution of a desorption isotherm due to drying-induced microstructural rearrangement is demonstrated. For numerical modeling, the microstructural alteration can be explicitly considered through a dynamic desorption isotherm model, which governs the local thermodynamic equilibrium at the capillary meniscus. This approach is implemented into a multiphase transport code, whose ability to predict drying is validated using literature data. Finally, the effect of prolonged drying on the colloidal nature of the calcium-silicate-hydrate gel is discussed.

36 MATERIALS SCIENCE↗

An analytical elastic plastic contact model with strain hardening and frictional effects for normal and oblique impacts

Impact between metallic surfaces is a phenomenon that is ubiquitous in the design and analysis of mechanical systems. We found that to model this phenomenon, a new formulation for frictional elastic–plastic contact between two surfaces is developed. The formulation is developed to consider both frictional, oblique contact (of which normal, frictionless contact is a limiting case) and strain hardening effects. The constitutive model for normal contact is developed as two contiguous loading domains: the elastic regime and a transitionary region in which the plastic response of the materials develops and the elastic response abates. For unloading, the constitutive model is based on an elastic process. Moreover, the normal contact model is assumed to only couple one-way with the frictional/tangential contact model, which results in the normal contact model being independent of the frictional effects. Frictional, tangential contact is modeled using a microslip model that is developed to consider the pressure distribution that develops from the elastic–plastic normal contact. This model is validated through comparisons with experimental results reported in the literature, and is demonstrated to be significantly more accurate than 10 other normal contact models and three other tangential contact models found in the literature.

36 MATERIALS SCIENCE↗

Magnetic hardening of CeFe12-xMox and the effect of nitrogenation

We report the magnetic hardening of CeFe12-xMox by melt spinning at surface wheel speeds between 10 m/s and 30 m/s. The synthesis range of CeFe12-xMox has been extended to CeFe11Mo, which uses the least amount of Mo substitution to stabilize the ThMn12-type structure. X-ray diffraction indicates that as-spun samples are multi-phased, typically consisting of a primary ThMn12-type phase with impurity phases of Fe-Mo alloy, Ce2Fe17 and CeFe2. However, nearly pure ThMn12-type phase can be obtained either by directly melt spinning at specific wheel speeds or by annealing the over-quenched ribbons at an optimum temperature. The magnetic moment of CeFe12-xMox is found to be affected not only by the number of Fe atoms but also by weakening of the Fe moment from Mo substitution. Nitriding is effective in enhancing the Curie temperature T-c and saturation magnetization 4 pi M-s. Tc was enhanced by at least 151 degrees C after nitrogenation for all compositions. The newly identified CeFe11Mo compound exhibits the best magnetic properties in the alloy series, having T-c = 370 degrees C and 4 pi M-s > 13.0 kG after nitriding and (BH)(max) = 0.3 MGOe after annealing. (C) 2013 Published by Elsevier B.V.

Zhou, C↗

Dislocation cross-slip in precipitation hardened Mg–Nd alloys

An integrated experimental characterization and molecular dynamics (MD) simulation approach was used to explore the dislocation-precipitate interactions in a dilute Magnesium–Neodymium (Mg–Nd) precipitation hardened alloy. In situ indentation in a transmission electron microscope (TEM) and postmortem TEM characterization of deformed samples and MD simulations revealed that basal < a > type dislocations interacted differently with β 1 (Mg 3 Nd) and β"(Mg 3-7 Nd) precipitates. For β" precipitates, the basal dislocations directly shear the precipitates. For β 1 precipitates, such shearing becomes much more difficult because it requires the creation of antiphase boundaries in the ordered lattice of β 1 precipitates. Screw dislocations were observed to cross-slip from basal to the prismatic plane, which could be parallel to the broad facet of β 1 precipitates. It is postulated that double cross-slip (basal to prismatic to basal) via the Hirsch mechanism may enable screw dislocations to overcome the β 1 precipitates. MD simulations also revealed that an edge dislocation is unable to bypass the precipitate via the generation of screw dislocation segments plus the double cross-slip mechanism. The edge dislocation can bow around the precipitate, and the segment that adopts a screw character can cross-slip to the prismatic plane but with increasing applied stress, cross-slips back to the original basal plane to continue glide via precipitate shearing. Finally, the implication of glide dislocation - β 1 -precipitate interaction mechanisms on the strength and ductility of β 1 precipitate dominant microstructures is discussed.

36 MATERIALS SCIENCE↗

Hardenability and microstructural evolution of a precipitation strengthened Ni 50 Ti 21 Hf 25 Al 4 alloy

NiTi-based quaternary alloys are used in a variety of mechanical components, such as bearings, actuators, and dampers, owing to their good hardenability, wear resistance, and corrosion resistance. Additionally, one of the most notable characteristics of NiTi-based alloys is their shape memory effect and pseudoelastic properties. Connecting the macroscopic processing parameters employed in the design of new intermetallic alloys to the nanoscale structural characteristics dictating their behavior is crucial for improving their mechanical properties and expanding the spectrum of potential applications. Here, in this work, an arc melted Ni 50 Ti 21 Hf 25 Al 4 (at%) alloy was solution treated at 1050 °C followed by quenching and aging at 600 °C to investigate the effect of aging time on the microstructure and mechanical properties. Two types of nano-sized precipitates were observed and determined as face-centered orthorhombic H-phase (TiHf)Ni and L2 1 Heusler precipitates Ni 2 TiAl. The morphology and orientation of the H-phase were investigated using scanning and transmission electron microscopy (SEM and TEM), elucidating the coarsening kinetics and strengthening contribution of that phase to the intermetallic mechanical behavior. Following coarsening, the presence of Heusler nanoprecipitates was detected under overaged conditions through TEM imaging and nanobeam electron diffraction patterns. A peak hardness condition of 756 HV was achieved after 70 h of aging, indicating that the co-precipitation of H-phase and Heusler precipitates through a well-designed aging treatment can lead to optimal mechanical performance, thus elevating the alloy’s potential as a viable material for industrial applications.

36 MATERIALS SCIENCE↗

Quantification of grain boundary effects on the geometrically necessary dislocation density evolution and strain hardening of polycrystalline Mg 4Al using in situ tensile testing in scanning electron microscope and HR-EBSD

In situ tensile testing in a scanning electron microscope (SEM) in conjunction with high-resolution electron backscatter diffraction (HR-EBSD) under load was used to characterize the evolution of geometrically necessary dislocation (GND) densities at individual grain boundaries as a function of applied strain in a polycrystalline Mg—4Al alloy. The increase in GND density was investigated at plastic strains of 0 %, 0.6 %, 2.2 %, 3.3 % from the area including 76 grains and correlated with (i) geometric compatibility between slip systems across grain boundaries, and (ii) plastic incompatibility. We develop expressions for the grain boundary GND density evolution as a function of plastic strain and plastic incompatibility, from which uniaxial tensile stress-strain response of polycrystalline Mg—4Al are computed and compared with experimental measurement. The findings in this study contribute to understanding the mechanisms governing the strain hardening response of single-phase polycrystalline alloys and more reliable prediction of mechanical behaviors in diverse microstructures.

Geometrically necessary dislocations↗

Optimizing Bendability and Hardness of Age-Hardenable Aluminum Sheets through Local Thermo-Mechanical Processing

This paper introduces a novel thermo-mechanical process to modify the local mechanical properties of 6xxx aluminum (Al-Mg-Si-Cu) alloy sheets. In this process, two pairs of rollers travel along the length of a sheet while locally bending and unbending it so that the final shape and thickness of the sheet remains unchanged. Room temperature bending/unbending (B/U) produces a deformation gradient through thickness and local hardening in both T4 and T6 sheets (with 41% and 18% greater Vickers hardness, respectively). High temperature bending/unbending performed at ~ 500°C via induction heating, produces significant improvements in local formability as measured by bend testing. Formability levels equivalent to the as-received T4 temper are achieved within the processed zones of T6 sheets with bend angles of ~ 150°, without disturbing the T6 temper in the remainder of the sheet. Finite element simulations and characterization explained the mechanical property improvements and the heterogenous microstructure with weakened Cube texture. Due to its similarity with the roller hemming process, and its compact dimensions, the apparatus developed for B/U has the potential for seamless integration with roller hemming robots to selectively process high strength aluminum sheet materials within mass-production settings.

Efe, Mert [BATTELLE (PACIFIC NW LAB)]↗

Spherical nanoindentation of proton irradiated 304 stainless steel: A comparison of small scale mechanical test techniques for measuring irradiation hardening

Experimentally quantifying the mechanical effects of radiation damage in reactor materials is necessary for the development and qualification of new materials for improved performance and safety. This can be achieved in a high-throughput fashion through a combination of ion beam irradiation and small scale mechanical testing in contrast to the high cost and laborious nature of bulk testing of reactor irradiated samples. The current paper focuses on using spherical nanoindentation stress-strain curves on unirradiated and proton irradiated (10 dpa at 360 °C) 304 stainless steel to quantify the mechanical effects of radiation damage. Spherical nanoindentation stress-strain measurements show a radiation-induced increase in indentation yield strength from 1.36 GPa to 2.72 GPa and a radiation-induced increase in indentation work hardening rate of 10 GPa–30 GPa. These measurements are critically compared against Berkovich nanohardness, micropillar compression, and micro-tension measurements on the same material and similar grain orientations. The ratio of irradiated to unirradiated yield strength increases by a similar factor of 2 when measured via spherical nanoindentation or Berkovich nanohardness testing. A comparison of spherical indentation stress-strain curves to uniaxial (micropillar and micro-tension) stress-strain curves was achieved using a simple scaling relationship which shows good agreement for the unirradiated condition and poor agreement in post-yield behavior for the irradiated condition. Finally, the disagreement between spherical nanoindentation and uniaxial stress-strain curves is likely due to the plastic instability that occurs during uniaxial tests but is absent during spherical nanoindentation tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural characterisation of nanocomposite nc-MeC/a-C coatings on oxygen hardened Ti-6Al-4V alloy

Nanocomposite coatings are novel, important systems composed of two or more nanocrystalline, or nanocrystalline and amorphous, phases. Such coatings offer a possibility of tailoring the coating microstructure and achieving new improved properties of coated materials. In this work a duplex surface treatment, consisting of an oxygen diffusion treatment and deposition of low friction nanocomposite nc-MeC/a-C (Me = transition metal, Ti, W or Cr) coatings, was applied for improvement of the Ti-6Al-4V alloy properties. The coatings composed of nanocrystallites of transition metal carbides (TiC or Cr{sub x}C{sub y} or WC) embedded in hydrogen-free amorphous carbon (a-C) matrix were deposited onto the surface of an oxygen hardened Ti-6Al-4 V alloy substrate by means of a simple DC magnetron sputtering. A nano/microstructure of the substrate material and coatings has been examined by scanning- and transmission electron microscopy complemented with the results of X-ray diffraction analyses. It was found that the nanocomposite coatings are composed of different carbide nanocrystals (with sizes of a few nanometres) embedded in an amorphous carbon matrix. The results of qualitative and quantitative analyses of the nanocrystalline phase in the coatings with use of high-resolution transmission electron microscopy combined with image analysis are given in the paper. An effect of the nano/microstructure parameters of the coated alloy onto its micro-mechanical (nanohardness and Young's modulus) and tribological properties (wear resistance and friction coefficient) is discussed in the paper.

36 MATERIALS SCIENCE↗

Microstructure characterization based on the type of deformed grains in cold-rolled, Cu-added, bake-hardenable steel

The electron backscatter diffraction technique has been used to characterize the microstructure of deformed grains in cold-rolled, Cu-added, bake-hardenable steel. A new scheme based on the kind and number of average orientations, as determined from a unique grain map of the deformed grains, was developed in order to classify deformed grains by type. The α-fiber components, γ-fiber components and random orientations, those which could not be assigned to either γ-fiber or α-fiber components, were used to define the average orientation of unique grains within individual deformed grains. The microstructures of deformed grains in as-rolled specimens were analyzed based on the Taylor factor, stored energy, and misorientation. The relative levels and distributions of the Taylor factor, the stored energy and the misorientation were examined in terms of the types of deformed grains. - Highlights: • We characterized the microstructure of Cu-added BH steel using EBSD. • A new scheme was developed in order to classify deformed grains by type. • Stored energy and misorientation are strongly dependent on the type of deformed grains. • Microstructure was examined in terms of the types of deformed grains.

36 MATERIALS SCIENCE↗

Effects of Fe atoms on hardening of a nickel matrix: Nanoindentation experiments and atom-scale numerical modeling

Significant hardening effect due to Fe concentrations in Ni-based alloys with face-centered-cubic structure has been studied by using a combined experimental and atomistic-based computational approach via nanoindentation tests. The obtained experimental load–displacement data for the [0 0 1] crystal orientation reached a qualitative good agreement with molecular dynamics simulations results, leading to strong evidence that the main strengthening factors are associated to sluggish dislocation diffusion, reduced defect sizes and the nucleation of tetrahedral stacking faults. Here, interstitial type prismatic dislocation loops mainly formed by $\frac{1}{6}$$\langle$1 1 2$\rangle$ Shockley dislocations are nucleated during the loading process, where their interaction leads to the formation of pyramidal shaped stacking fault which are mainly created by $\frac{1}{3}$$\langle$1 0 0$\rangle$ Hirth dislocations lines. Observing both types of defects coexisting in the same plastic deformation zone by both approaches. Reported mechanical data, measured experimentally and interpreted numerically, are also in accordance with microstructural SEM and TEM investigations.

36 MATERIALS SCIENCE↗

Development of coherent-precipitate-hardened high-entropy alloys with hierarchical NiAl/Ni 2 TiAl precipitates in CrMnFeCoNiAl x Ti y alloys

Coherent precipitates hardening is currently emerging strengthening mechanism of the various high entropy alloys (HEAs). Recently, CrMnFeCoNiAl x HEAs have been studied to show a phase transition from face-centered-cubic (FCC) to body-centered-cubic (BCC) and formation of coherent precipitates (B2-NiAl) within the BCC matrix. The coherent precipitates in the CrMnFeCoNiAl x alloys could contribute to increase the strength but lead to considerable reduction of the ductility. The present work systematically investigated a series of CrMnFeCoNiAl 0.5 Ti x alloys to further improve the strength and plasticity, as compared to the previously reported CrMnFeCoNiAl x HEAs. As a result, an increase of Ti addition leads to the phase transition from FCC to BCC and formation of lamellar structure and hierarchical precipitates reinforced by B2-NiAl and L2 1 -Ni 2 TiAl phases. Excellent mechanical properties were achieved from CrMnFeCoNiAl 0.5 Ti 0.1 and CrMnFeCoNiAl 0.5 Ti 0.2 alloys. Herein, the mechanical properties of the CrMnFeCoNiAl 0.5 Ti x alloys were discussed via theoretical strengthening mechanisms.

36 MATERIALS SCIENCE↗

A high-strength precipitation hardened cobalt-free high-entropy alloy

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. A Co-free (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 88 Ti 4 Al 8 HEA was developed and studied in this work. In contrast to previous Co-free HEAs, this alloy is close to equiatomic in its composition and promises a more pronounced high-entropy effect. Scanning electron microscopy, transmission electron microscopy, atom probe tomography, and synchrotron-based, high-energy X-ray diffraction were used to characterize this alloy and revealed a complex four-phase structure, with an FCC matrix, γ’ precipitates, and a network of B2 and χ phase particles. This structure granted 2151 MPa compressive strength and good thermal stability, but with limited ductility and slow precipitation kinetics. A strengthening analysis of the alloy shows that the B2 and χ provided the most significant strengthening contribution, adding 312 MPa and 788 MPa respectively. Furthermore the strengthening effect from the nanoscale γ' is also considerable, adding 608 MPa in total. This study lays the foundation for the continued development of high-strength Co-free HEAs with improved and satisfactory ductility.

36 MATERIALS SCIENCE↗

A multi-length-scale investigation of the applicability of ductility laws for annealed and work-hardened copper

Small-scale mechanical testing provides unique advantages over conventional testing in investigating the mechanical response of nuclear materials. While small-scale testing enables accelerated materials research, it raises the question of comparability to large-scale properties for engineering design considerations. Among different mechanical properties for structural design considerations such as yield and ultimate tensile stress, ductility is of critical importance with respect to structural component health. The effectiveness of using small-scale mechanical testing for probing these mechanical properties is dictated by understanding how the mechanical responses translate from the microscale to the engineering scale. Therefore, a better understanding of size scaling effects via gathering and analysis of experimental data is required to bridge length-scales. Further, this work builds upon previous reports to provide statistical data on how mechanical response changes as the size of the specimens are reduced from conventional sizes. One hundred twenty mesoscale tensile coupons of oxygen-free high thermal conductivity (OFHC) copper in work-hardened and annealed state have been manufactured using micro-wire electrical discharge machining (EDM) and tested under uniaxial tension. The mesoscale specimens have dimensions dictated by pre-selected geometric ratios (i.e., gauge section length over the square root of the cross-section area) with gauge length dimensions of 3 mm (or less) and sub-millimeter gauge widths and thicknesses. The mesoscale responses were compared to bulkscale properties to reveal the effect of specimen size on the mechanical response as a function of grain size and material state for a single phase face-centered cubic metal.

36 MATERIALS SCIENCE↗

Effects of compositional complexity on the ion-irradiation induced swelling and hardening in Ni-containing equiatomic alloys

The impact of compositional complexity on the ion-irradiation induced swelling and hardening is studied in Ni and six Ni-containing equiatomic alloys with face-centered cubic structure. The irradiation resistance at the temperature of 500 °C is improved by controlling the number and, especially, the type of alloying elements. Alloying with Fe and Mn has a stronger influence on swelling reduction than does alloying with Co and Cr. Lastly, the quinary alloy NiCoFeCrMn, with known excellent mechanical properties, has shown 40 times higher swelling tolerance than nickel.

36 MATERIALS SCIENCE↗

Ionic liquids as oil additives for lubricating oxygen-diffusion case-hardened titanium

This study attempts to use ionic liquids (ILs) as oil additives to lubricate oxygen-diffusion (OD) case-hardened titanium for improved friction and wear behavior. Four oil-soluble ILs were used as additives in a base oil for boundary lubrication of an OD-treated Ti-6Al-4V surface sliding against a bearing steel ball. The ILs improved the friction behavior to various extents and the two phosphate ILs clearly outperformed the conventional ZDDP. Unlike ZDDP that adversely caused a higher material loss, ILs exhibited excellent wear protection suggesting good material-chemical compatibility. Particularly, the carboxylate IL protected the OD-Ti surface from any measurable wear. As a result, the morphology and chemical composition of the worn surfaces and tribofilms were examined to gain insights of the anti-wear mechanism.

36 MATERIALS SCIENCE↗

Nonmonotonic Strain Rate Dependence on the Strain Hardening of Polymer Nanocomposites

This Letter investigates the external deformation on modifying the polymer–nanoparticle (NP) and NP–NP interactions as well as their influences on the macroscopic properties of polymer nanocomposites (PNCs). Specifically, the applied uniaxial extension brings together the NPs along the transverse stretching direction and catalyzes the percolation transition from the initially well-dispersed NPs in the PNCs. The percolated NP network thus increases the strength of PNCs and leads to a strong surge in the elongation viscosity at very low strain rates, exhibiting the unexpected nonmonotonic strain rate dependence on the strain hardening. These results reveal explicitly the unconventional roles of the external deformation on modulating the relative strength of the polymer–NP and the NP–NP interactions, enabling advanced structures and properties control of PNCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗