Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gasoline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Investigation of fuel film formation and soot emissions in a GDI engine during cold-start with Split-injection strategies

This study investigates the impact of fuel-film formation on engine-out soot emissions in a gasoline direct injection (GDI) engine under cold-start conditions. Split-injection strategies were applied by varying the number of injections, injection duration, and total fuel quantity to affect wall wetting and control the average in-cylinder equivalence ratio. A combined experimental and numerical approach was employed to analyze fuel-film deposition, combustion efficiency, and engine-out soot and unburnt hydrocarbons (UHC) emissions. In particular, fuel film distribution estimated by means of non-reacting, 3-D, computational fluid dynamics (CFD) simulations, together with experimentally measured soot data, were used to investigate fuel film formation and its role in soot generation. In the experiments, a skip-fired engine control strategy was applied to mimic the transient nature of engine cold-start operation. The results indicate that, under the same total number of injections, increasing the average in-cylinder equivalence ratio through longer injection durations improves combustion stability, as indicated by the decrease of the coefficient of variation of IMEP n (Net Indicated Mean Effective Pressure) from 6.0 % to 0.6 %. However, this strategy leads to higher soot emissions, which increased by nearly an order of magnitude, primarily due to enhanced wall-film formation. In contrast, increasing the number of injections while maintaining a constant equivalence ratio significantly impacts fuel-film deposition and, consequently, soot emissions, with a fivefold reduction of the measured engine-out soot, decreasing from 3.5 mg to 0.7 mg. A soot-film correlation was developed and achieved a high coefficient of determination (r 2 = 0.95) and was further extended to account for spark timing effects. These findings confirm the effectiveness of split-injection for avoiding wall film formation and soot emissions, and the critical role of fuel film in soot generation, supporting the hypothesis that pool fires play a crucial role in contributing to soot formation under these cold-start conditions. In conclusion, the study also indicates the value of a predictive soot-film correlation for developing cold-start emission control strategies.

Engine Cold-start↗
DOE OSTI2020

An experimental and kinetic modeling study of cyclopentane and dimethyl ether blends

Cyclopentane is a suitable naphthene, or cycloalkane, in a palette for multi-component gasoline surrogate fuels due to its presence in market fuels and its relevance to alkyl substituted cyclopentanes also present. However, the previous oxidation studies of cyclopentane have primarily focused on neat mixtures. Blending cyclopentane with dimethyl ether in this work therefore serves to inform our understanding of, and improve predictive models for, multi-component mixtures. Here, the auto-ignition of cyclopentane/dimethyl ether blends was studied in a high-pressure shock tube and in a rapid compression machine. A wide range of temperatures (650 – 1350 K) and elevated pressures of 20 and 40 bar were studied at equivalence ratios of 0.5, 1.0 and 2.0 in air for two blending ratios (30/70 and 70/30 mole% cyclopentane/di-methyl ether mixtures). A detailed kinetic model for cyclopentane was revised to capture the measured ignition delay times and apparent heat release rates in this study. Literature ignition delay time, jet-stirred reactor, and laminar burning velocity measurements of neat cyclopentane were used as additional validation. Improvements to the kinetic model were based on recent literature studies related to sub-models including cyclopentene and cyclopentadiene which allowed the removal of previous local rate-constant optimizations. Low temperature reactivity of cyclopentane was found to be controlled by the branching ratio between concerted elimination of HO͘ 2 and the strained formation of Q&#775OOH radicals in agreement with previous studies. In this study, the low branching ratio of Q&#775OOH formation increases the influence of a competing consumption pathway for cyclopentyl-peroxy (CPTO͘ 2 J) radicals. The sensitivity of the simulated ignition delay times to the formation of cyclopentyl hydroperoxide (CPTO 2 H), from CPTO͘ 2 J and HO͘ 2 , is discussed. The current model is used to analyze the influence of dimethyl ether on the reactivity of cyclopentane in the context of previous literature studies of dimethyl ether binary blends with ethanol and toluene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Correlating armature and needle dynamics with voltage waveforms of solenoid-actuated GDI injector

The injector voltage hump that appears near the needle closing has been used for the real-time monitoring and feedback control of fuel injection duration in modern engines. This voltage hump has been thought to result from the abrupt change in electromagnetic induction by the stoppage of needle motion but detailed electromagnetic processes and associated armature and needle dynamics during the needle closing have not been thoroughly investigated in a wide range of injection conditions, which knowledge is crucial for the delicate control of fuel injection based on the voltage hump. Here, the current study analyzes the transient armature and needle dynamics of a solenoid-actuated gasoline direct injection injector using an X-ray phase-contrast imaging technique. Then, the results are correlated with voltage waveforms during the needle closing transient under various injection pressures, injection pulse durations, and dwell times of split injections. The time derivatives of voltage waveforms showed lower and upper peaks in order in the regime of the voltage hump. Inconsistent with conventional understandings, the lower peak timing of the voltage derivative did not match with the timing of needle closing (end of injection) but rather matched with the abrupt descent timing of the armature and needle. The inflection timing and upper peak timing of the voltage derivative matched with the timings of actual needle closing and armature closing respectively. The amplitude of the voltage hump was near linearly dependent on the needle closing speed. The needle closing speed decreased upon the decrease of injection pulse duration and injection pressure which made it difficult to detect the voltage humps in ballistic injection regimes and low injection pressures. In split injection conditions, the voltage hump of the first injection was not detectable if the dwell time was shorter than the needle closing delay, the time from the current cut-off to the actual needle closing.

42 ENGINEERING↗
DOE OSTI2020

Spray formation mechanism of diverging-tapered-hole GDI injector and its potentials for GDI engine applications

The gasoline-direct-injection market recently, which has shown the improved spray atomization and lower engine particulate emissions compared to conventional straight-hole nozzles. However, the near-nozzle spray formation mechanism associated with this atomization potential of the diverging-he potentials of the diverging-tapered-hole nozzle for GDI engine applications. The analyses focus on the in- and near-nozzle flow structure, and flow dynamics and stability outside the nozzle. We find that the results showed that the diverging-tapered-hole nozzle coupled with proper hole length generated the radially expanding crescent-moon-like flow structure in the hole that promoted the spray atomization and dispersion outside the nozzle. The expansion of the hole cross-sectional area in the diverging-tapered-hole nozzle was appeared to attenuate the mutual interactions of fuel flows in the hole from various origins that formed rather stable sprays. These flow characteristics are discussed to be promising for the compact and robust spray generation for GDI engine applications.

42 ENGINEERING↗
DOE OSTI2020

Simulating combustion of a seven-component surrogate for a gasoline/ethanol blend including soot formation and comparison with experiments

Combustion of a seven-component surrogate for a research grade 87 octane gasoline mixed with 10% ethanol is investigated experimentally and numerically from the perspective of an isolated droplet burning under conditions that promote one-dimensional gas transport. The numerical analysis included a kinetic mechanism comprised of 398 species and 24,814 reactions and a soot model that accounted for nucleation, surface growth, coalescence/aggregation of soot particles, and luminous flame radiation. Measurements of droplet and flame diameters were made for an initial droplet diameter (D o ) of approximately 0.63 mm. The simulations agreed well with the measurements including the location of the soot shell. Preferential vaporization was revealed by simulations of the liquid concentrations in the droplet. Predicted peak soot volume fractions coincided with temperatures between 1300 K and 1400 K as a soot inception temperature. Simulations were also carried out for D o between 0.25 mm and 5 mm to explore the effect of radiation and D o on burning. Below 0.25 mm radiation was negligible and burning rates and flame temperatures converged to a single value. Increasing D o up to 1.8 mm lowered the burning rate with luminous radiation having a strong effect. When radiation was entirely removed from the model the burning rate was nearly constant. Above D o = 2 mm droplets extinguished almost immediately after ignition. The flame temperature decreased with increasing D o while it increased when radiation was omitted. As a result, the simulations show that soot precursors including polyaromatic hydrocarbons were concentrated around the soot shell.

42 ENGINEERING↗
DOE OSTI2024

A comprehensive numerical investigation on spray models for Direct-Injection Spark-Ignition engines

Gasoline direct-injection spark-ignition (DISI) engines generate a large portion of their unburned hydrocarbon (UHC) and soot emissions during the cold-start phase. A predictive computational fluid dynamics (CFD) modeling framework can be used to understand the physical processes that characterize fuel spray evolution and fuel-film formation at cold start conditions, which can help to reduce engine-out particulate emissions. This study systematically evaluated spray submodels and developed a set of simulation best practices for physical-numerical submodels with the goal of enabling accurate simulations of liquid spray behavior in a DISI engine. Three comprehensive experimental datasets containing free-spray projected liquid volume (PLV), liquid volume fraction (LVF), and near-field X-ray radiography data were used to validate the simulation results and evaluate the spray submodels. Systematic analysis delved into injected parcel distribution, droplet collision, spray breakup, and evaporation via a detailed assessment of the relevant spray submodels. Moreover, the effects of turbulence models and the initial turbulent flow properties on the liquid spray evolution were examined. Based on extensive calibration efforts, a set of simulation best practices for the free spray was developed and validated against the PLV/LVF data. Simulation results indicated that the uniform distribution for parcel initialization, coupled with appropriate droplet collision submodels, provides an improved spray morphology compared to the cluster distribution. The findings also underscored the importance of calibrating the Kelvin-Helmholtz Rayleigh-Taylor (KH-RT) breakup model constants and droplet heat transfer coefficient scaling factor to achieve favorable agreement regarding measured liquid penetration and spray widths. In conclusion, this study marks a substantial stride towards accurately predicting fuel film evolution and soot formation within DISI engine performance.

ECN Spray G↗
DOE OSTI2024

A numerical study of ignition and flame development characteristics in GCI combustion using large eddy simulations and chemical explosive mode analysis

Here, this work investigates the ignition and flame development processes of low reactivity fuel combustion under compression ignition conditions based on the large eddy simulation approach. The chemical explosive mode analysis (CEMA) is employed to characterize the local combustion features, including gas-liquid fuel zone, auto-ignition, diffusion-assisted, extinction, cool flame and post-ignition zone, among which auto-ignition and post-ignition are found to play a key role in the overall heat release process. The local flame propagation modes in gasoline compression ignition (GCI) are determined by quantifying the relative magnitude of diffusion/chemistry at a representative progress variable in the pre-ignition zone. The results show that autoignition fronts and deflagration waves exist simultaneously in the ignition and intense high temperature heat release (HTHR) stages, but autoignition fronts dominate. In addition, the chemical kinetic processes of four heat release periods are analyzed. The heat release during the ignition period is found to be dominated by the reactions CH 3 + H (+M) <=> CH 4 (+M) and CH 3 CHO + H <=> CH 2 CHO + H 2 . The reaction CH 2 OH + OH <=> CH 2 O + H 2 O always plays an important role in the heat releases during the other three combustion stages including intense HTHR, moderate HTHR and post-combustion.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Affordability of Household Transportation Fuel Costs by Region and Socioeconomic Factors

Transportation energy is an important component of household budgets. Household vehicle fuel, one part of total transportation energy costs is over 3% of total household expenditures nationwide in the U.S. The average annual expenditure of over $2,000 for vehicle fuel (mostly gasoline) is comparable to the total average household expenditures for electricity and natural gas combined. However, these average values vary geographically, and lower income households can face higher energy cost burdens. The highly resolved data developed in this study reveals the variation of household energy burdens across the country and provides localized data to support local decision making.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Co-optimized Mixed-Mode Engine and Fuel Demonstrator for Improved Fuel Economy while Meeting Emissions Requirements

Progressively increasing regulatory demands on fuel economy and future global emission standards have led to a focus on advanced engine development to improve overall engine efficiency and fulfill emission requirements. Low temperature combustion (LTC) and gasoline compression ignition (GCI) are promising technologies to achieve these goals and have the advantage of using existing refinery infrastructure and subsequent economies of scale for a robust energy supply. By applying spark ignition (SI) for cold start, LTC for low load operations, and GCI for medium to high load operations, a multimode GCI engine concept was proposed and the fuel formation was co-optimized to maximize fuel economy improvement potential while maintaining ULEV 70 emissions standards. HATCI has successfully demonstrated the feasibility of this multimode GCI engine concept, and confirmed the fuel economy improvement over the baseline SI engine by simulating the FTP75 vehicle drive cycle. In this report, the technical approaches, multimode engine control, and engine test results of both steady state and transitions, CFD modeling, fuel testing, and FTP75 drive cycle simulation results are summarized, followed with technical challenges observed, and recommendations for possible follow-up studies.

02 PETROLEUM↗
DOE OSTI2020

Elucidation of the Reaction Mechanisms of Autooxidative Processes in Complex Condensed-Phase Mixtures

In this report, we discuss the oxidative processes of gasoline surrogate fuels comprised of a neat olefin, such as 1-hexene. Oxidative reactions are thought to involve the peroxyl radical and peroxide chemistry with initial hydrogen abstraction by O 2 , followed by addition of O 2 or HOO· to the hydrocarbon to form unstable peroxy radicals and peroxides that result in a chain reaction. In the condensed phase environment (liquid), we also consider polymeric-forming chain reactions, such as hydrocarbon radical-radical carbon chain growth. We present our experimental results showing the reaction products resulting from 1-hexene oxidation, along with chemical kinetic modeling of the system showing product ratios as a function of time. Applicability of our observations to oxidation-promoted fouling in hydrocarbon fuels (i.e., formation of gum) and radical-promoted polymerizations will also be discussed.

10 SYNTHETIC FUELS↗
DOE OSTI2025

Using Separation-Enhanced Isotope Ratio Mass Spectrometry to Enable Increased Renewable Carbon Content in Transportation Fuels (CRADA 525)

Stable isotope ratio measurements of carbon atoms using isotope ratio mass spectrometry (IRMS) can be an effective tool for quantifying biogenic carbon in co-processed fuels, with results approaching the precision and accuracy of accelerator mass spectrometry (AMS). The lower cost of an IRMS may enable deployment to refineries, improving access and analysis turnaround times (≤2 hours), and, by extension, provide data that can allow process optimization to maximize renewable carbon in desired refinery products. This project explored the integration of chemical separation with IRMS analyses to enable highly detailed tracking of biogenic carbon into fuel product streams separated by boiling point range, chemical class, or specific compound. Forty-nine fuels and fuel components of fossil and biogenic origin, spanning gasoline and diesel boiling point ranges, were received from three refiners and were analyzed for their δ 13 C values via IRMS. Results spanned a 13 C range from ca. 10‰ to 44‰ and reflect materials derived from sustainable sources (e.g., C4 or C3 plants, animal-based pathways, syngas) or from fossil-derived fuels. Common ranges are approximately 18‰ to 9‰ and approximately 30‰ to 20‰ for C4 and C3 plants, respectively, and approximately 34‰ to 24‰ and approximately 70‰ to 33‰ for petroleum-derived fuels and methane, respectively. Fuel-like standards were developed and tested using direct-injection elemental analyzer (EA) IRMS for liquid fuels. This method was compared with the published methods, yielding statistically similar results. Four blend curve sets were produced ranging from 0% to 100% of a fuel containing biogenic carbon, focusing on 0% to 10% biogenic carbon. Linear fits were the most applicable for two of the four blend curve sets; however, two sets were found to exhibit slightly quadratic behavior, which was more pronounced in low biogenic blend samples, necessitating second-order fits. The origin of the slight quadratic behavior remains unclear; however, the discussion points to possible interpretations. CanmetENERGY thoroughly characterized a majority of the samples using one- and two-dimensional gas chromatography (GC and GC×GC, respectively) and other analyses. Selected samples were subjected to solid phase extraction (SPE) for saturate, olefin, aromatic, and polar (SOAP) analysis, and the resulting solvent-diluted fractions containing saturates and aromatics were returned to Pacific Northwest National Laboratory (PNNL), where the solvent was removed via evaporation or physical separation using GC techniques. Characterization and separations provided an understanding of saturate and aromatic content, as well as boiling point ranges for each sample and sample fraction. Samples resulting from SPE were examined using EA-IRMS and gas chromatography combustion IRMS (GC-C-IRMS) analyses. Both approaches suggest that the range in values between end-members can be increased by selecting the paraffinic or aromatic fraction of the end-member or by selecting among individual compounds resulting from GC separation of the paraffinic fractions. Considerable work remains to put these approaches into practice and statistically validate the benefit for using a fraction or individual compound over bulk analysis of a sample. However, initial results suggest that separations provide advantages for samples having blend ratios of less than 10% biogenic blendstocks. 13 C results showed statistically similar biofuel blend results to those obtained at PNNL, although additional work is needed to obtain better reproducibility. Select samples were sent to Los Alamos National Laboratory (LANL) for IRMS measurements and Beta Analytics for AMS measurements. This work suggests that IRMS and AMS yield closely comparable results and in some circumstances, IRMS could serve as a surrogate for AMS. While additional work is needed to better resolve statistical advantages for separations and better show the comparable nature of IRMS and AMS in both the biogenic carbon analysis of bulk chemical classes, initial results from this study suggest that these should be pursued in order to proliferate this approach for quantifying biogenic carbon in transportation fuels to the refinery level, thereby potentially enabling process optimization in co-processing scenarios.

09 BIOMASS FUELS↗
DOE OSTI2022

Quantification of Sub-Pixel Dynamics in High-Speed Neutron Imaging

The high penetration depth of neutrons through many metals and other common materials makes neutron imaging an attractive method for non-destructively probing the internal structure and dynamics of objects or systems that may not be accessible by conventional means, such as X-ray or optical imaging. While neutron imaging has been demonstrated to achieve a spatial resolution below 10 μm and temporal resolution below 10 μs, the relatively low flux of neutron sources and the limitations of existing neutron detectors have, until now, dictated that these cannot be achieved simultaneously, which substantially restricts the applicability of neutron imaging to many fields of research that could otherwise benefit from its unique capabilities. In this work, we present an attenuation modeling approach to the quantification of sub-pixel dynamics in cyclic ensemble neutron image sequences of an automotive gasoline direct injector at a 5 μs time scale with a spatial noise floor in the order of 5 μm.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Potential Impacts of High-Octane Fuel Introduction in a Naturally Aspirated, Port Fuel-Injected Legacy Vehicle

In recent years there has been an increased interest in raising the octane level of gasoline to enable higher compression ratios (CR) in spark-ignition engines to improve vehicle fuel efficiency. A number of studies have examined opportunities to increase efficiency in future vehicles, but potential impacts on the legacy fleet have not received as much attention. In this study, our effort focused on experimental studies on an engine using high-octane fuels without changing the engine’s CR. Spark timing was advanced until maximum torque was reached or knock was encountered for each engine condition, using each individual fuel to maximize engine efficiency. Knock-limited conditions occurred as the output brake mean effective pressure (BMEP) neared the maximum attainable output at a given engine speed. Increasing research octane numbers generally enabled knock-free operation under a greater number of operating conditions. Vehicle modeling using Autonomie was used to project vehicle energy use, fuel economy, and tailpipe CO 2 emissions for the Urban Dynamometer Driving Schedule (UDDS), the Highway Fuel Economy Test (HWFET), and the US06 cycle. Results show that decreases in energy consumption of up to 2% for a small SUV are possible through the use of a 97 RON fuel compared to a baseline using 91 RON fuel, provided that the formulation of the fuel does not cause unanticipated operational issues such as lower maximum BMEP. Greater improvements using high-octane fuels are possible if the CR is increased, but there is no opportunity to increase the CR in legacy vehicles. Thus, these vehicles realize an improvement from increased octane rating in accordance with their ability to spark advance to take advantage of a fuel with a higher octane rating. For the modeled vehicle, improvements of up to 2% in volumetric fuel economy may be possible through the use of a 97 RON fuel with the largest gains expected on the US06 cycle. Fuel economy impacts are strongly coupled to the heating value of the fuels in addition to changes in engine efficiency. Similarly, decreases in tailpipe CO 2 emissions are also achievable. However, simultaneous improvements in energy consumption, fuel economy, and tailpipe CO 2 emissions are not guaranteed and are dependent upon fuel formulation.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Bulk Spray and Individual Plume Characterization of LPG and Iso-Octane Sprays at Engine-Like Conditions

This study presents experimental and numerical examination of directly injected (DI) propane and iso-octane, surrogates for liquified petroleum gas (LPG) and gasoline, respectively, at various engine like conditions with the overall objective to establish the baseline with regards to fuel delivery required for future high efficiency DI-LPG fueled heavy-duty engines. Sprays for both iso-octane and propane were characterized and the results from the optical diagnostic techniques including high-speed Schlieren and planar Mie scattering imaging were applied to differentiate the liquid-phase regions and the bulk spray phenomenon from single plume behaviors. The experimental results, coupled with high-fidelity internal nozzle-flow simulations were then used to define best practices in CFD Lagrangian spray models. Optical imaging revealed that unlike iso-octane, propane’s spray propagation was fed by its flash boiling, spray collapse, and high degree of vaporization, resulting in a direct proportionality of propane’s penetration length to temperature. These unique features of propane and its variation from iso-octane’s spray pattern, contributed to its classification as an unconventional spray. Appropriate corrections to the injection and breakup models were developed to reproduce the under-expanded jet dynamics and to mimic the flash boiling-driven spray development observed with propane sprays. The simulation results were found to be sensitive to cone and inclusion angles of the blob injector. The current work represents a first assessment of the capability of the commonly available models for engine-spray simulations and highlights the fact that, despite the reasonable agreement obtained in the fuel vapor morphology, the representation of the liquid phase lacks accuracy and requires further model development.

02 PETROLEUM↗
DOE OSTI2023

Soot Formation and Ignition Characteristics of Ethanol/Gasoline Blends in a Rapid Compression Machine

With the ever-increasing demand for sustainable energy, alcohol fuels have garnered interest for use in heavy duty engines. The significant infrastructure for ethanol production and blending of ethanol with gasoline make these fuels/fuel blends desirable candidates. However, development of heavy duty engine technology that is capable of burning alcohol fuels while retaining the advantages of traditional diesel combustion requires an improved understanding of the soot formation for these fuels under conditions relevant to mixing-controlled combustion. This work uses an extinction diagnostic to study the sooting tendency of ethanol and gasoline/ethanol blends ranging from E10 to E98 during ignition in a homogeneous environment. Experiments were conducted in a rapid compression machine (RCM) for compressed conditions of 20 ± 1 bar and an approximately constant temperature (± 10K) which was unique for each fuel. For a given soot volume fraction, a linear relationship was observed between ethanol content and the equivalence ratio in which that soot volume fraction was formed. Accounting for the oxygenated nature of ethanol, E85 and E98 fuels produced similar amounts of soot at a given Φ ox, , suggesting other factors outside of fuel oxygen content, such as fuel morphology, impact soot formation. Ignition delay data is reported for compressed pressures of 20 ± 1 bar and compressed temperatures ranging from 633 – 670 K for E10 and 771 – 789 K for E98. Varying pressures for E10 and E98 at conditions producing similar soot volume fractions demonstrated a linear dependence of soot formation on pressure, regardless of if the pressure considered was at top dead center or peak combustion pressure. Furthermore, the data gleaned from this work will be used to select soot models and chemical kinetic mechanisms for RCM simulations to ultimately model heavy duty engine technology with the studied fuels.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

BETO 2021 Peer Review - Thermochemical Platform Analysis WBS: 2.1.0.302

The objective of the NREL Thermochemical Platform Analysis (WBS 2.1.0.302) project is to inform and guide R&D priorities for thermal and catalytic conversion processes by providing process design and techno-economic analysis (TEA). This is achieved through close collaboration with researchers and external experts, along with the use of both commercially available modeling tools and the development or use of collaboration-derived domain-specific tools and resources, such as refinery integration, kinetic and reactor models, phase equilibrium models, and pertinent bio-products market studies. This project is directly aligned with DOE-BETO goals, with the enabling of technology advancements and cost reduction for biomass derived biofuels being one of its primary objectives. TEA-guided research facilitated by this project has helped achieve significant modeled cost reductions for the ex situ catalytic fast pyrolysis (CFP) pathway and the indirect liquefaction (IDL) pathway for the conversion of syngas to high-octane gasoline (HOG). Cost reduction through refinery integration, development of valuable co-products, and other options are being identified for future research to help reduce the modeled MFSP to $2.50/GGE by 2030. Additional priorities anticipated in the future, such as the use of renewable electricity for liquid fuels and products, and emphasis on waste utilization are also being explored in conjunction with research on catalytic utilization of syngas and other gases (including CO2). Industry-relevant parameters are given deliberate attention as part of the work done under this project to help answer questions important for future commercialization and address associated risks.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

A Full Spectrum of Characterization for Insight into Carbon Speciation and Removal on a Cu/BEA Catalyst During Renewable High-Octane Hydrocarbon Synthesis

Conversion of methanol and dimethyl ether to high-octane gasoline catalyzed by beta zeolite (BEA) provides an opportunity for the production of high-quality fuels from renewable carbon sources (e.g., gasified biomass). Recent research demonstrated that a Cu-modified BEA zeolite catalyst (Cu/BEA) offered advantages over the unmodified BEA catalyst due to multifunctional Cu species that enabled incorporation of co-fed H2, reactivation of light alkanes, and reduction of products from the aromatic hydrocarbon pool. The shift in hydrocarbon pool chemistry has the potential to influence the identity and relative composition of surface carbon species that are often linked to deactivation. A detailed understanding of these carbon species is important to develop an effective and efficient regeneration procedure that can enable the transition from fundamental catalyst development to commercial application. Here, we applied complementary ex situ and in situ characterization techniques to compare the structures of surface carbon species on post-reaction Cu/BEA and unmodified BEA catalysts. Both catalysts contained acyclic and aromatic hydrocarbons along with graphitic carbon species. However, the post-reaction Cu/BEA catalyst had a lower polycyclic aromatic content, and further, the graphitic species were more hydrogenated and defective. It was also found that the presence of Cu promoted carbon removal at lower temperatures than for unmodified BEA through activation of O2 by Cu during thermal oxidation. The fundamental insight into the composition of surface carbon species enabled the design of an effective and efficient regeneration strategy for the DME homologation reaction over Cu/BEA, resulting in full recovery of the catalyst activity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Simulation and Optimization of Volatile Fatty Acid Upgrading Strategies for Sustainable Transportation Fuel Production

Underutilized wet waste is a promising feedstock for production of carbon-neutral or carbon-negative liquid transportation fuels. Arrested methanogenesis of wet wastes by microbes, which produces mixtures of C2-C8 carboxylic acids (volatile fatty acids, VFAs), is practiced industrially at a pilot scale and the VFA products can be catalytically upgraded to molecules suitable for use as transportation fuels (alcohols and alkanes) via sequential ketonization and hydrogenation, both steps of which have been demonstrated with high (>90%) yield at the lab scale. We present in this work a simulation-based decision-making framework which evaluates upgrading strategies of VFAs to alcohol- and hydrocarbon-based neat and blended diesel, jet, and gasoline fuels. The processes utilize sequential upgrading steps (ketonization and hydrogenation) accompanied by one distillation step (either separating VFAs before ketonization or alcohols after ketone hydrogenation) to form two liquid streams: a light alcohol stream best suited as a light-duty fuel and a heavy alcohol or hydrocarbon stream best suited as a diesel or jet fuel. Suitability of the liquid products as transportation fuels and maximum blending levels with petrofuels comes from simulation of critical fuel properties (boiling point, flash point, lower heating value, viscosity, melting point, water solubility, and cetane/octane number). Catalytic upgrading steps and fuel property mixing models used by the simulation are experimentally validated. We demonstrate the flexibility of the decision-making algorithm by evaluating processing scenarios for experimentally-observed VFA profiles with varied carbon chain length distributions. Processing scenarios are optimized for either maximum total renewable carbon utilization or production of heavy-duty (jet or diesel) fuels. We evaluate the economic viability and CO2 emissions of each proposed upgrading scenario using techno-economic and life cycle analyses. The decision-making framework developed in this work can also be used to down-select promising strategies for upgrading of other bio-based feedstocks to sustainable fuels and chemicals.

aviation fuel↗