Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRINDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Anomalous effects of Sc substitution and processing on magnetism and structure of (Gd 1-x Sc x ) 5 Ge 4

The kinetic arrest observed in the parent Gd 5 Ge 4 gradually vanishes when a small fraction (x = 0.025, 0.05 and 0.10) of Gd is replaced by Sc in (Gd 1-x Sc x ) 5 Ge 4 , and the magnetic ground state changes from antiferromagnetic (AFM) to ferromagnetic (FM). A first order phase transition coupled with the FM-AFM transition occurs at T C = 41 K for x = 0.05 and at T C = 53 K for x = 0.10 during heating in applied magnetic field of 1 kOe, and the thermal hysteresis is near 10 K. The first-order magnetic transition is coupled with the structural Sm 5 Ge 4 -type to Gd 5 Si 4 -type transformation. The magnetization measured as a function of applied magnetic field shows sharp metamagnetic-like behavior. At the same time, the AFM to paramagnetic transition in (Gd 1 x Sc x ) 5 Ge 4 with x = 0.10, is uncharacteristically broad indicating development of strong short-range AFM correlations above the Néel temperature. Comparison of the magnetization data of bulk, powdered, and metal-varnish composite samples of (Gd 0.95 Sc 0.05 ) 5 Ge 4 shows that mechanical grinding and fabrication of a composite have little effect on the temperature of the first-order transformation, but short-range ordering and AFM/FM ratio below T C are surprisingly strongly affected.

36 MATERIALS SCIENCE↗

A novel in-situ, lift-out, three-point bend technique to quantify the mechanical properties of an ex-service neutron irradiated inconel X-750 component

A first of its kind small scale mechanical testing technique involving micro-three-point bending was invented, developed, and implemented on reactor irradiated, active Inconel X-750 components removed from service after approximately 53 and 67 dpa. These tests were performed at ambient room temperature in-situ using a scanning electron microscope in order to obtain live recordings of sample deformation and loading curves. Sample and testing apparatus preparation required novel lift-out and fabrication processes. Materials from two irradiation temperature regimes, low temperature (120-280 °C) and high temperature (300 ± 15 °C) were examined. Manufacturing and finishing (grinding) of this component create differences between its edge and center, so micro-specimens from both areas were extracted in order to study these differences. According to three-point beam bending theory, a 0.2% offset yield stress parameter is introduced and calculated for all specimens. Differences in mechanical properties due to irradiation temperature and dose effects were observed. Material irradiated at the higher temperature exhibited yield strength increases of ~540 MPa after 53 dpa and ~1000 MPa after 67 dpa. There was little difference (≤310 MPa) in yield strength between materials irradiated at the lower temperature at 53 dpa and 67 dpa compared with non-irradiated material. Differences in yield strengths between the edge and center of the component are retained after irradiation. The difference in yield strengths for the edge and center regions was ~740 MPa for non-irradiated material. After irradiation to a dose of 67 dpa these differences were ~570 MPa for the lower irradiation temperature and ~710 MPa for higher irradiation temperature. There were no indications of grain boundary failures via cracking except for material irradiated to 67 dpa at low temperature.

36 MATERIALS SCIENCE↗

Eco-friendly and effective strategy to synthesize ZnO/Ag{sub 2}O heterostructures and its excellent photocatalytic property under visible light

Highlights: • ZnO/Ag{sub 2}O photocatalysts with heterostructures were synthesized via a facile mechanochemical method. • The synthetic process does not involve any organic solvents and the reaction matrix can be recycled easily. • The synthetic method is gram-scale, and we can easily and routinely scale up this process to produce grams of the heterostructure nanomaterials. • The as-prepared samples without post-calcination show a high degree of crystallinity. - Abstract: ZnO/Ag{sub 2}O photocatalysts with heterostructure were synthesized by a green and effective mechanochemical method. The preparation process was taken in solid state at room temperature with a short grinding time. The as-made products showed a high degree of crystallinity without post-calcination treatment. Such synthetic method does not involve any organic solvents and the reaction matrix can be recycled. The as-prepared ZnO/Ag{sub 2}O samples show excellent photocatalytic activity and photostability for degradation of different organic dyes under visible light. The content of Ag{sub 2}O plays an important role in the photocatalytic activity, which can be tuned by the precursor AgNO{sub 3}. The photodegradation rate constant (k) of the optimal ZnO/Ag{sub 2}O sample under visible light is nearly 0.1004 min{sup −1} for methylene blue (MB), 0.063 min{sup −1} for rhodamine B (RHB) and 0.07 min{sup −1} for methyl orange (MO), which are much better than the pure ZnO (0.0075 min{sup −1}). The enhancement of the visible light photocatalytic activity could be attributed to the heterojunction interfaces induced by the match of crystal lattice and energy band between the Ag{sub 2}O and ZnO. The Ag{sub 2}O generates the excited-state electrons under visible light irradiation. The excited electrons on Ag{sub 2}O could directly transfer to the conduction band (CB) of ZnO, making ZnO/Ag{sub 2}O present remarkable visible light photocatalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A microstructural analysis of aluminum buildup during thermomechanical processing

Highlights: • Microstructure of roll coating developed on a ground steel work roll was examined. • Roll coating was formed during the 20 pass hot rolling schedule of an Al-Mg alloy. • The roll coating had a complex layered nanocrystalline and amorphous structure. • The roll coating layers were composed of metallic Al, porous MgO and C. • Work roll debris, Fe and Cr, were observed embedded within the roll coating. - Abstract: The microstructure and composition of a roll coating built-up on an AISI M2 steel work roll during a 20 pass hot rolling schedule using a laboratory rolling tribo-simulator with a roll-on-block configuration was examined. The AISI M2 steel work roll was characterized by grinding grooves and possessed a surface roughness (R{sub a}) of 0.17 μm. The roll coating developed under these lubricated conditions was discontinuous, patchy and streaked out in the rolling direction. The microstructure and chemical composition of the material transfer that made up the roll coating was analysed and revealed to possess a complex composite microstructure consisting of nanocrystalline aluminum, nanocrystalline/amorphous MgO and amorphous carbon layers. The nanocrystalline MgO layers were porous structures lying between the solid metallic aluminum layers. Debris particles from the wear of the work roll were detected embedded within the carbon layer and at the base of the roll coating. The microstructure of the roll coating appear to be determined by the deformation conditions experienced during the rolling process, while its composition is dependent on the composition of the rolled alloy, the work roll and the lubrication conditions employed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The role of tungsten phases formation during tungsten metal powder consolidation by FAST: Implications for high-temperature applications

Highlights: • Lowering the sintering temperature of W to 2173 K by using FAST. • Application of electron microscopy for microstructure characterisation. • W{sub 2}C shell formation due to C difussion from graphite tooling. • Identification of co-formed secondary phase, WO{sub 2}. • Influence of WO{sub 2} on high-thermal applications. - Abstract: Tungsten is a candidate material for the demonstration fusion power plant DEMO. To ensure high density and structural stability, Field-Assisted Sintering Technique (FAST) is proposed as a consolidation method. This study discusses the formation of phases during sintering of tungsten by the FAST. Scanning electron microscopy, X-ray diffraction and transmission electron microscopy were used to evaluate the microstructure in tungsten-based materials. The results of microscopic examinations revealed the in-situ formation of tungsten oxide and a formation of tungsten carbide shell around tungsten core. Tungsten carbide-rich shell is formed due to the carbon diffusion from the graphite die used in the FAST into tungsten at high temperatures. In contrast to easy removal of tungsten carbide shell by mechanical grinding, the formation of tungsten oxide in the W-matrix can influence the performance of such material when used as plasma-facing material in the fusion reactor. High-temperature experiments at 1873 K showed that tungsten-oxide phase starts to decompose, which results in material degradation and formation of voids and surface blisters.

36 MATERIALS SCIENCE↗

A study of microstructure of Fe-Cu-Ni-Sn and Fe-Cu-Ni-Sn-VN metal matrix for diamond containing composites

Highlights: • A nanocrystalline sample of coarse-grained powders of iron, copper, nickel, tin was obtained. • The structure of the sample consists of a supersaturated solid solution of nitrogen and vanadium in α-Fe. • Grain refinement occurs as a result of the decomposition of supersaturated solid solution of nitrogen and vanadium in α-Fe. To obtain bulk of 51Fe–32Cu–9Ni–8Sn and 49.47Fe–31.04Cu–8.73Ni–7.76Sn–3VN nanocomposites, a pressing method at room temperature and subsequent hot pressing in a vacuum was used. The microstructure of the sintered composites by X-ray diffraction and transmission electron microscopy was investigated. It is shown that in the 49.47Fe–31.04Cu–8.73Ni–7.76Sn–3VN composite there was a dissolution of vanadium nitride in γ‑iron and formation of a supersaturated solid solution of nitrogen and vanadium in the α‑iron. As a result, there was a substantial grinding of ferrite grains (from 5 to 50 μm to 20–400 nm) as compared to a sample without vanadium nitride (from 5 to 50 μm to 400–800 nm). Nanocomposites are considered as promising materials to create a new generation of diamond containing composites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Solid-state synthesis and electrical properties of polyaniline/Cu-montmorillonite nanocomposite

In this paper, the solid-state synthesis of polyaniline/Cu-montmorillonite nanocomposite is reported. Mixture of anilinium chlorure and Cu exchanged montmorillonite was grinded at room temperature while we vary the molar rate of aniline to interlayer Cu{sup 2+} cations (R) from 0.5 to 6. The properties of the hybrid compounds are characterized by X-ray diffraction, thermogravimetric analysis, SEM, FTIR and impedance spectroscopy. The results showed that the structure and the conductivity of PANI in hybrid materials depend on R. The ac conduction showed a regime of constant dc conductivity at low frequencies and a crossover to a frequency-dependent regime of the type A {omega}{sup s} at high frequencies.

36 MATERIALS SCIENCE↗

Characterization of exfoliated/delamination kaolinite

A novel and facile approach for the preparation of exfoliated/delamination kaolinite was reported in this study. Kaolinite was mechanochemically activated by grinding with dimethylsulfoxide in a globe mill for different periods of time, and then the activated samples were treated for several hours at 120 {sup o}C to obtain the precursors of kaolinite. The resulting materials were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. The experimental data indicated that the clay layers were well exfoliated/delamination under mechanochemical effect in a significantly short intercalation time. The expansion of the basal spacing (d{sub 001}) of raw kaolinite by 0.40 nm pointed out that the hydrogen bonds between adjacent kaolinite layers were partially broken as a result of the intercalation with dimethylsulfoxide.

36 MATERIALS SCIENCE↗

Low-temperature synthesis of Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} with cubic garnet-type structure

Highlights: Black-Right-Pointing-Pointer One-step synthesis and its optimization of cubic garnet Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} at 750 Degree-Sign C. Black-Right-Pointing-Pointer Instability above 800 Degree-Sign C of the Al-free cubic Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12}. Black-Right-Pointing-Pointer Li{sup +}-ion conductivity without adventitious Al{sup 3+}. -- Abstract: In this paper, we report the direct synthesis of Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} with the cubic garnet-type structure at low temperature with a lattice constant of 13.0035 Angstrom-Sign . The synthesis condition is optimized to be at 750 Degree-Sign C for 8 h with 30 wt% excess lithium salt. No intermediate grinding was involved in this straightforward route. Without the adventitious of Al{sup 3+}, the cubic Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} is unstable above 800 Degree-Sign C and has an ionic conductivity of the order of 10{sup -6} S cm{sup -1}.

36 MATERIALS SCIENCE↗

Preparation of MgH{sub 2} composite with a composition of 40%MgH{sub 2} + 30%LiBH{sub 4} + 30%(2LiBH{sub 4} + MgF{sub 2})

Graphical abstract: Hydrogen content vs. desorption time curves for consecutive 1st desorptions of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) at 533–873 K. Highlights: ► Addition of MgF{sub 2} and LiBH{sub 4} with a higher hydrogen storage capacity to MgH{sub 2}. ► Preparation of 40%MgH{sub 2} + 30%LiBH{sub 4} + 30% (2LiBH{sub 4} + MgF{sub 2}) composite. ► Examination of desorption properties of the composite. ► Total desorbed hydrogen quantity for consecutive 1st desorptions of 7.07 wt%. ► Reactions of LiBH{sub 4} → LiH + B + (3/2)H{sub 2}, and 2LiBH{sub 4} + MgF{sub 2} → 2LiF + MgB{sub 2} + 4H{sub 2}. -- Abstract: A mixture of containing two chemical equivalents of lithium borohyride and one equivalent of magnesium fluoride is known to yield hydrogen in an amount of about 7.6 wt% of the mixture when heated to about 150 °C at atmospheric pressure by the following reaction; 2LiBH{sub 4} + MgF{sub 2} = 2LiF + MgB{sub 2} + 4H{sub 2}. In order to increase hydrogen storage capacity of Mg-based materials, a mixture with a composition of 2LiBH{sub 4} + MgF{sub 2} and LiBH{sub 4}with a higher hydrogen storage capacity of 18.4 wt% were added to MgH{sub 2}. MgH{sub 2} composite with a composition of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) was prepared by reactive mechanical grinding. The hydrogen storage properties of the sample were then examined. Hydrogen content vs. desorption time curves for consecutive 1st desorptions of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) at 533–873 K showed that the total desorbed hydrogen quantity for consecutive 1st desorptions is 7.07 wt%.

36 MATERIALS SCIENCE↗

Mechanochemical synthesis of layered hydroxy salts

Highlights: ► Ultrafast synthesis method was developed for the synthesis of layered hydroxy salts. ► Preparation of hydroxy single salt by this method requires only one minute. ► Hydroxy salts with variable Ni/Zn ratio could be synthesized by varying the metal contents of the starting mixture. ► This synthesis method is solvent free and environment friendly. -- Abstract: A simple one minute synthesis method was adapted for the preparation of layered hydroxy salts of copper, zinc, nickel and cadmium by grinding the metal salts with sodium hydroxide in a mortar. This solvent free method is environment friendly and fast. This method could be extended to the preparation of Ni/Zn hydroxy double salts. The Ni/Zn ratio could be varied from 1.2 to 1.9 by varying the metal contents of the precursor salts without the formation of any impurities in the sample. The prepared compounds had similar characteristics as that of the samples prepared by precipitation route. No sign of carbonate contamination was observed in any of the prepared samples.

36 MATERIALS SCIENCE↗

Microstructure and martensitic transformation in Si-coated TiNi powders prepared by ball milling

Graphical abstract: - Highlights: • Amorphous Si-coated TiNi powders were prepared successfully by ball milling. • Ti{sub 4}Ni{sub 4}Si{sub 7} was formed at the interface between Si and TiNi after annealing. • Si-coated Ti–Ni powders displayed the R phase after annealing. - Abstract: Si was coated on the surface of Ti–49Ni (at%) alloy powders by ball milling in order to improve the electrochemical properties of the Si electrodes of secondary Li ion batteries and then the microstructure and martensitic transformation behavior were investigated by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Ti–Ni powders coated with Si were fabricated successfully by ball milling. As-milled powders consisted of highly deformed Ti–Ni powders with the B2 phase and amorphous Si layers. The thickness of the Si layer coated on the surface of the Ti–Ni powders increased from 3–5 μm to 10–15 μm by extending the milling time from 3 h to 48 h. However, severe contamination from the grinding media, ZrO{sub 2} occurred when the ball milling time was as long as 48 h. By heating as-milled powders to various temperatures in the range of 673–873 K, the highly deformed Ti–Ni powders were recovered and Ti{sub 4}Ni{sub 4}Si{sub 7} was formed. Two-stage B2–R–B19′ transformation occurred when as-milled Si-coated Ti–49Ni alloy powders were heated to temperatures below 873 K, above this temperature one-stage B2–B19′ transformation occurred.

36 MATERIALS SCIENCE↗

Synthesis of Fe/SiO{sub 2} and iron oxides/SiO{sub 2} nanocomposites by long-term ball milling

Graphical abstract: - Highlights: • Iron–iron oxides/silica composites are synthesized by long term dry ball-milling. • Bcc iron and α-quartz powders are used as precursors. • Surface effects enhance coercivity in iron/silica nanocomposites. • In spite of their small size, about 10 nm, iron particles are ferromagnetic. • Ferro and superparamagnetic particles are found in maghemite/silica composites. - Abstract: Iron oxide/SiO{sub 2} nanocomposites are synthesized by dry ball-milling a mixture of bcc Fe and α-quartz powders for prolonged times. A sequence of nanocomposites is obtained, with small magnetic particles dispersed in a non magnetic, amorphous matrix. The powders are characterized by X-ray diffraction and transmission electron microscopy. The magnetic hysteresis properties are investigated in the range 50–300 K. After 120 h milling, deformed, non-spherical, α-Fe nanocrystallites of about 10 nm in size and very few small (<10 nm) maghemite particles are found. At room temperature, iron particles are ferromagnetic and a large effective magnetic anisotropy is estimated, which is mainly attributed to surface effects. Between 160 and 200 h milling, maghemite nanoparticles are observed while after 220 h grinding, hematite phase appears; after 340 h milling, the sample consists of ferromagnetic hematite particles with a broad size distribution (5–50 nm) embedded in an amorphous matrix.

36 MATERIALS SCIENCE↗

From natural attapulgite to phosphor materials: Characterization, photoluminescence and structure

Highlights: • Sr{sub 2.965}Al{sub 0.08}Si{sub 0.92}O{sub 5}:0.025Ce{sup 3+}, 0.01Eu{sup 2+} phosphor was synthesized from natural attapulgite. • Pure Sr{sub 3}SiO{sub 5} phase can be easily obtained. • It provides a new application field as phosphor for natural attapulgite. - Abstract: Sr{sub 2.965}Al{sub 0.08}Si{sub 0.92}O{sub 5}:0.025Ce{sup 3+}, 0.01Eu{sup 2+} (SrAlSiO:Ce{sup 3+}, Eu{sup 2+}) phosphor from natural attapulgite (ATP) was synthesized by solid-state reaction method. For the use of ATP as a source of Si and Al, pretreatment process including mechanical grinding and acid leaching were involved. X-ray diffraction patterns confirmed the formation of silicates in a wide temperature field, whereas Sr{sub 3}SiO{sub 5} within a single step. The ATP fibers were tuning into phosphor particles (about 1.5–3.0 μm) after calcination. Furthermore, photoluminescence spectra of the SrAlSiO:Ce{sup 3+}, Eu{sup 2+} phosphor was also in good agreement with the literature results, indicating a promising potential application as an effective candidate for warm-white LEDs materials.

36 MATERIALS SCIENCE↗

The experimental study of the effect of microwave on the physical properties of multi-walled carbon nanotubes

Highlights: • We study the microwave effect on the multi-walled carbon nanotubes (MWCNTs). • We examine the non uniform heating effect on the physical structure of MWCNTs. • We examine the purification of MWCNTs by microwave. • We analyze the thermal characteristics of microwave treated MWCNTs. - Abstract: This paper reports the effect of microwave on the physical properties of multi-walled carbon nanotubes (MWCNTs) where different power levels of microwave were applied on MWCNTs in order to apprehend the effect of microwave on MWCNTs distinctly. A low energy ball milling in aqueous circumstance was also applied on both MWCNTs and microwave treated MWCNTs. Temperature profile, morphological analysis by field emission scanning electron microscopy (FESEM), defect analysis by Raman spectroscopy, thermal conductivity, thermal diffusivity as well as heat transfer coefficient enhancement ratio were studied which expose some strong witnesses of the effect of microwave on the both purification and dispersion properties of MWCNTs in base fluid distilled water. The highest thermal conductivity enhancement (6.06% at 40 °C) of MWCNTs based nanofluid is achieved by five minutes microwave treatment as well as wet grinding at 500 rpm for two hours.

36 MATERIALS SCIENCE↗

Facile synthesis of MoO{sub 2}@C nanoflowers as anode materials for sodium-ion batteries

Graphical abstract: The as-obtained MoO{sub 2}@C nanoflowers deliver a reversible capacity of 172 mAh g{sup −1} at 0.1 A g{sup −1} and a capacity of 166 mA h g{sup −1} after 1000 cycles at 1.0 A g{sup −1}. - Highlights: • MoO{sub 2}@C nanoflowers are synthesized. • Irregular MoO{sub 2}@C nanoparticles are synthesized. • MoO{sub 2}@C nanoflowers deliver a reversible capacity of 172 mAh g{sup −1} at 0.1 A g{sup −1}. - Abstract: Sodium-ion batteries (NIBs) have been considered to be the promising alternative to lithium-ion batteries (LIBs) due to the limited availability and uneven distribution of lithium resources. The exploration of anode materials for SIBs was still limited, and transition metal oxides (TMOs) have been widely studied for a long time. MoO{sub 2}@C nanoflowers were synthesized through a grinding method, followed by an annealing process. In addition, irregular MoO{sub 2}@C nanoparticles could be synthesized, when the amount of ammonium molybdate was increased by twice while other condition kept the same. With excellent dispersity and structural integrity, the as-obtained MoO{sub 2}@C nanoflowers deliver a reversible capacity of 172 mAh g{sup −1} at 0.1 A g{sup −1} and a capacity of 166 mA h g{sup −1} after 1000 cycles at 1.0 A g{sup −1}.

36 MATERIALS SCIENCE↗

Horizons of modern molecular dynamics simulation in digitalized solid freeform fabrication with advanced materials

Our ability to shape and finish a component by combined methods of fabrication including (but not limited to) subtractive, additive and/or no theoretical mass-loss/addition during the fabrication is now popularly known as solid free form fabrication. Fabrication of a telescope mirror is a typical example where grinding and polishing processes are first applied to shape the mirror and thereafter an optical coating is usually applied to enhance its optical performance. The area of nanomanufacturing cannot grow without a deep knowledge of the fundamentals of materials and consequently, the use of computer simulations is becoming ubiquitous. This article is intended to introduce the most recent advances in the computation benefit specific to the area of solid free form fabrication as these systems are traversing through the journey of digitalisation and Industry-4.0. Specifically, this article demonstrates that the application of the latest materials modelling approaches, based on techniques such as molecular dynamics, are enabling breakthroughs in applied precision manufacturing techniques.

36 MATERIALS SCIENCE↗

Initial examination of fuel compacts and TRISO particles from the US AGR-2 irradiation test

Post-irradiation examination was completed on two as-irradiated compacts from the US Advanced Gas Reactor Fuel Development and Qualification Program’s second irradiation test. These compacts were selected for examination because there were indications that they may have contained particles that released cesium through a failed or defective SiC layer. The coated particles were recovered from these compacts by electrolytic deconsolidation of the surrounding graphitic matrix in nitric acid. The leach-burn-leach (LBL) process was used to dissolve and analyze exposed metallic elements (actinides and fission products), and each particle was individually surveyed for relative cesium retention with the Irradiated Microsphere Gamma Analyzer (IMGA). Data from IMGA and LBL examinations provided information on fission product release during irradiation and whether any specific particles had below-average retention that could be related to coating layer defects or radiation-induced degradation. A few selected normal-retention particles and six with abnormally-low cesium inventory were analyzed using X-ray tomography to produce three-dimensional images of the internal coating structure. Four of the low-cesium particles had obviously damaged or degraded SiC, and X-ray imaging was able to guide subsequent grinding and polishing to expose the regions of interest for analysis by optical and electron microscopy. Additional particles from each compact were also sectioned and examined to study the overall radiation-induced microstructural changes in the kernel and coating layers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗