Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Furnace”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

A Study of the Growth of Single Crystals

Research on the growth of single crystals of the III-V compound indium antimonide was pursued in order to gain a firsthand knowledge of some factors which govern the growth of single crystals of this compound. These studies were conducted using a standard Czochralski crystal pulling furnace. This type of furnace allows crystals to be formed without being constrained to a crucible. Several factors were found to have a large detrimental effect on the growth of single crystals of indium antimonide, the most important of which seems to be the degree to which the environment surrounding the crystal during growth can be controlled. Ways to overcome these effects were determined and are outlined.

Desmet, D. J.↗
NASA NTRS1972

Eutectic Experiment Development for Space Processing

A ground base test plan and a specimen evaluation scheme have been developed for the aluminum-copper eutectic solidification experiment to be run in the M518 multipurpose electric furnace during the Skylab mission. Besides thermal and solidification studies a detailed description is given of the quantitative metallographic technique which is appropriate for characterizing eutectic structures. This method should prove a key tool for evaluating specimen microstructure which is the most sensitive indicator of changes produced during solidification. It has been recommended that single grain pre-frozen eutectic specimens be used to simplify microstructural evaluation and to eliminate any porosity in the as-cast eutectic specimens. High purity (99.999%) materials from one supplier should be employed for all experiments. Laboratory studies indicate that porosity occurs in the MRC as-cast eutectic ingots but that this porosity can be eliminated by directional freezing. Chemical analysis shows that the MRC ingots are slightly Al rich and contain about .03% impurity. Because of the impurity content the lower cooldown rate (1.2 C/min) should be used for eutectic freezing if MRC material is used in the M518 furnace.

Hopkins, R. H.↗
NASA NTRS1973

Cyclic oxidation evaluation: Approaching application conditions

A survey is presented of the cyclic furnace and burner rig oxidation facilities at NASA-Lewis Research Center together with a review of selected test results and an initial interpretation of the data obtained. Cyclic furnace tests are used to conveniently screen alloy oxidation resistance and spall tendency; high velocity tests further indicate dynamic environmental resistance. Alloys which form scales predominantly of Cr2O3/chromite spinel spall much more than those forming alpha Al2O3/aluminate spinel scales. Weight changes due to scale spalling were used to estimate alloy depletion/thickness losses.

Barrett, C. A.↗
NASA NTRS1973

The thermal and mechanical properties of a low density elastomeric ablation material

Thermal and mechanical properties data were obtained for a low density elastomeric resin based ablation material with phenolic-glass honeycomb reinforcement. Data were obtained for the material in the charred and uncharred state. Ablation material specimens were charred in a laboratory furnace at temperatures in the range from 600 K to 1700 K to obtain char specimens representative of the ablation char layer formed during reentry. These specimens were then used to obtain effective thermal conductivity, heat capacity, porosity, and permeability data at the char formation temperature. This provided a boxing of the data which enables the prediction of the transient response of the material during ablation. Limited comparisons were made between the furnace charred specimens and specimens which had been exposed to simulated reentry conditions.

Engelke, W. T.↗
NASA NTRS1972

Studies of the performance of W-Re type thermocouples.

The effect of exposure of bare-wire and BeO-insulated commercial W-Re thermocouple materials to high temperatures in gaseous environments was investigated. The temperature range of interest was primarily 2000 to 2400 K, and the investigations were confined to thermocouple wires of 0.25 mm diameter. Thermoelements were examined for metallurgical structural changes and chemical changes by conventional methods. In the temperature range of interest, grain growth was inhibited in the chemically doped W-3% Re alloy, and excellent room-temperature ductility was retained subsequent to the exposure. The compatibility of high purity (in excess of 99.8%), sintered BeO insulators with the thermoelements differed, depending upon whether the BeO-insulated thermoelement assemblies were self-heated electrically or heated in a furnace; in tests in argon environments, highly reliable performance occurred when the assemblies were heated in a furnace. BeO-insulated W-3% Re vs W-25% Re thermocouples, constructed with degassed and aged materials, exhibited drifts equivalent to about 3 mK/hr during 1000 hours of exposure at 2073 K in argon while in the presence of tantalum.

Burns, G. W.↗
NASA NTRS1974

Fused silicon-rich coatings for superalloys

Various compositions of nickel-silicon and aluminum-silicon slurries were sprayed on IN 100 specimens and fusion-sintered to form fully dense coatings. Cyclic furnace oxidation tests in 1 atm air at 1100 C showed all the coatings to be protective for at least 600 hours, and one slurry, Al-60Si, was protective for 1000 hours. This coating also protected NASA TAZ 8A and NASA-TRW VIA for 1000 hours in the same furnace test. Alloys B 1900, TD-NiCr, and Mar-M200 were protected for lesser times, while NX 188 and NASA WAZ 20 were scarcely protected at all. Limited stress-rupture testing on 0.64-cm-diam IN 100 specimens detected no degradation of mechanical properties due to silicon diffusion.

Smialek, J. L.↗
NASA NTRS1974

The thermal and mechanical properties of a low-density glass-fiber-reinforced elastomeric ablation material

An evaluation of the thermal and mechanical properties was performed on a molded low-density elastomeric ablation material designated as Material B. Both the virgin and charred states were examined to provide meaningful inputs to the design of a thermal protection system. Chars representative of the flight chars formed during ablation were prepared in a laboratory furnace from 600 K to 1700 K and properties of effective thermal conductivity, heat capacity, porosity and permeability were determined on the furnace chars formed at various temperature levels within the range. This provided a boxing of the data which will enable the prediction of the transient response of the material during flight ablation.

Engelke, W. T.↗
NASA NTRS1973

Arc melting and homogenization of ZrC and ZrC + B alloys

A description is given of the methods used to arc-melt and to homogenize near-stoichiometric ZrC and ZrC-boron alloys, giving attention to the oxygen contamination problem. The starting material for the carbide preparation was ZrC powder with an average particle size of 4.6 micron. Pellets weighing approximately 3 g each were prepared at room temperature from the powder by the use of an isostatic press operated at 50,000 psi. These pellets were individually melted in an arc furnace containing a static atmosphere of purified argon. A graphite resistance furnace was used for the homogenization process.

Darolia, R.↗
NASA NTRS1975

Sinter of uniform, predictable, blemish-free nickel plaque for large aerospace nickel cadmium cells

A series of nickel slurry compositions were tested. Important slurry parameters were found to be the nature of the binder, a pore former and the method of mixing. A slow roll mixing which is non-turbulent successfully eliminated entrapped air so that bubbles and pockets were avoided in the sinter. A slurry applicator was developed which enabled an equal quantity of slurry to be applied to both sides of the grid. Sintering in a furnace having a graded atmosphere characteristic, ranging from oxidizing to strongly reducing, improved adhesion of porous sinter to grid and resulted in a uniform welding of nickel particles to each other throughout the plaque. Sintering was carried out in a horizontal furnace having three heating zones and 16 heating control circuits. Tests used for plaque evaluation include (1) appearance, (2) grid location and adhesion, (3) mechanical strength, (4) thickness, (5) weight per unit area, (6) void volume per unit area, (7) surface area and (8) electrical resistance. Plaque material was impregnated using Heliotek proprietary processes and 100 AH cells were fabricated.

Seiger, H. N.↗
NASA NTRS1975

Low cost processes for solar-grade silicon

Upgrading metallurgical grade silicon is being pursued in four associated areas in order to improve the purity of the normally 98% material. The first two work areas involve purification of raw materials entering the process in addition to upgrading the arc furnace itself. The second two areas of process upgrading comprise improving the purity of the silicon after it leaves the arc furnace by reactive gas blowing and unidirectional freezing. The best cell produced to date was fabricated from MG-Si that had been blown with an O2-Cl2 mixture, unidirectionally solidified, and 6-float-zone passed (to determine a base boron level of 0.04 ohm/cm). The cell showed a 10.7% AMO efficiency. In the other processes category, the use of silicates as a silicon source and of electrolysis as a process were studied. The best electrolytic process uses a 1000 C fused salt of silica in cryolite.

Hunt, L. P.↗
NASA NTRS1976

A system using solid ceramic oxygen electrolyte cells to measure oxygen fugacities in gas-mixing systems

Details are given for the construction and operation of a 101.3 kN/sq m (1 atmosphere) redox control system. A solid ceramic oxygen electrolyte cell is used to monitor the oxygen fugacity in the furnace. The system consists of a vertical quench, gas mixing furnace with heads designed for mounting the electrolyte cell and with facilities for inserting and removing the samples. The system also contains the high input impedance electronics necessary for measurements, a simplified version of a gas mixing apparatus, and devices for experiments under controlled rates of change relative to temperature and redox state. The calibration and maintenance of the system are discussed.

Williams, R. J.↗
NASA NTRS1976

High Temperature Strain Gage Calibration Fixture

An apparatus and method are described for calibrating high temperature strain gases which serve for both dead weight and constant deflection measurements. A cantilever support arm allows the test unit to slide into a furnace while one end is subjected to bending strain either by hanging weights upon it or by deflecting it with a push rod. The dual nature of the fixture permits both tests to be run without change of the test specimen or removal from the furnace.

Vranas, T.↗
NASA NTRS1977

Current status of droplet and liquid combustion

The present understanding of spray combustion in rocket engine, gas turbine, Diesel engine and industrial furnace applications is reviewed. In some cases, spray combustion can be modeled by ignoring the details of spray evaporation and treating the system in the same manner as a gaseous diffusion flame; however, in many circumstances, this type of simplification is not adequate and the turbulent two-phase flow must be considered. The behavior of individual droplets is a necessary component of two-phase models and recent work on transient droplet evaporation, ignition and combustion is considered, along with a discussion of important simplifying assumptions involved with modeling these processes. Methods of modeling spray evaporation and combustion processes are also discussed including: one-dimensional models for rocket engine and prevaporized combustion systems, lumped zone models (utilizing well-stirred reactor and plug flow regions) for gas turbine and furnace systems, locally homogeneous turbulent models, and two-phase models. The review highlights the need for improved injector characterization methods, more information of droplet transport characteristics in turbulent flow and continued development of more complete two-phase turbulent models.

Faeth, G. M.↗
NASA NTRS1977

Current status of droplet and liquid combustion

The present understanding of spray combustion in rocket engine, gas turbine, Diesel engine and industrial furnace applications is reviewed. In some cases, spray combustion can be modeled by ignoring the details of spray evaporation and treating the system as a gaseous diffusion flame; however, in many circumstances, this simplification is not adequate and turbulent two-phase flow must be considered. The behavior of individual droplets is a necessary component of two-phase models and recent work on transient droplet evaporation, ignition and combustion is considered, along with a discussion of important simplifying assumptions involved with modeling these processes. Methods of modeling spray evaporation and combustion processes are also discussed including: one-dimensional models for rocket engine and prevaporized combustion systems, lumped zone models (utilizing well-stirred reactor and plug flow regions) for gas turbine and furnace systems, locally homogeneous turbulent models, and two-phase models. The review highlights the need for improved injector characterization methods, more information of droplet transport characteristics in turbulent flow and continued development of more complete two-phase turbulent models

Faeth, G. M.↗
NASA NTRS1978

Investigation of the fracture mechanism of Ti-5Al-2.5Sn at cryogenic temperatures

Fractography and metallographic sectioning were used to investigate the influence of microstructure on the fracture mechanism and fracture toughness (KIC) of normal interstitial and extra low interstitial (ELI) Ti-5Al-25Sn at 20 K (-423 F) and 77 K (-320 F). Plates of each grade were mill annealed at 815 C followed by either air or furnace cooling. These variations in composition and cooling rate resulted in differences in the volume fraction and internal structure of the dispersed beta phase and in the ordering of the alpha matrix. The ELI alloys were tougher than the normal interstitial plates. KIC of the furnace-cooled ELI plate was 25% lower than that of the air-cooled ELI material. Variations in cooling rate had no influence of KIC of the normal interstitial alloys. Fractography showed that a large portion of the fracture surfaces were covered with elongated dimples. Metallographic sections of specimens deformed at 77 K showed that these features form at the intersections of slip bands or deformation twins with grain or twin boundaries. Ordering and higher interstitial levels increase the local strain in slip bands resulting in void nucleation at lower macroscopic strains and lower KIC values.

Van Stone, R. H.↗
NASA NTRS1978

Static and dynamic cyclic oxidation of 12 nickel-, cobalt-, and iron-base high-temperature alloys

Twelve typical high-temperature nickel-, cobalt-, and iron-base alloys were tested by 1 hr cyclic exposures at 1038, 1093, and 1149 C and 0.05 hr exposures at 1093 C. The alloys were tested in both a dynamic burner rig at Mach 0.3 gas flow and in static air furnace for times up to 100 hr. The alloys were evaluated in terms of specific weight loss as a function of time, and X-ray diffraction analysis and metallographic examination of the posttest specimens. A method previously developed was used to estimate specific metal weight loss from the specific weight change of the sample. The alloys were then ranked on this basis. The burner-rig test was more severe than a comparable furnace test and resulted in an increased tendency for oxide spalling due to volatility of Cr in the protective scale and the more drastic cooling due to the air-blast quench of the samples. Increased cycle frequency also increased the tendency to spall for a given test exposure. The behavior of the alloys in both types of tests was related to their composition and their tendency to form scales. The alloys with the best overall behavior formed alpha-Al2O3 aluminate spinels.

Barrett, C. A.↗
NASA NTRS1978

Applications of thermal energy storage to process heat and waste heat recovery in the iron and steel industry

The system identified operates from the primary arc furnace evacuation system as a heat source. Energy from the fume stream is stored as sensible energy in a solid medium (packed bed). A steam-driven turbine is arranged to generate power for peak shaving. A parametric design approach is presented since the overall system design, at optimum payback is strongly dependent upon the nature of the electric pricing structure. The scope of the project was limited to consideration of available technology so that industry-wide application could be achieved by 1985. A search of the literature, coupled with interviews with representatives of major steel producers, served as the means whereby the techniques and technologies indicated for the specific site are extrapolated to the industry as a whole and to the 1985 time frame. The conclusion of the study is that by 1985, a national yearly savings of 1.9 million barrels of oil could be realized through recovery of waste heat from primary arc furnace fume gases on an industry-wide basis. Economic studies indicate that the proposed system has a plant payback time of approximately 5 years.

Katter, L. B.↗