Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Faradaic Efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Durability Optimization of CO 2 Electrolyzers for Syngas Evolution

Recently, there has been an increased interest in mitigating anthropogenic CO 2 emissions through the electrochemical conversion of CO 2 into fuels and fuel feedstocks, including hydrogen gas (H 2 ), carbon monoxide (CO), and mixtures of the two to yield syngas. Commercial applications of these systems require high catalytic selectivity for the desired products, while exhibiting operational lifetimes exceeding thousands of hours. Advancements in this field have produced systems that display high selectivity of the desired products at faradaic efficiencies exceeding 95%. Despite the advancements made in CO 2 electrolysis, system durability remains a standing challenge in the field. CO 2 electrolyzer lifetimes are often limited by carbonate fouling, catalyst degradation, detrimental flooding of electrode microporous layers and anion exchange membrane (AEM) failures. In this report, a 5 cm 2 membrane electrode assembly (MEA) device is used to investigate potential failure modes and to optimize AEM CO 2 electrolyzer operation. Key findings of this study include the importance of CO 2 flow rate, use of a thin PiperION PTFE-reinforced membrane, optimizing compression to enhance contact under 40 in-lb compression, and the effect of more compressible, commercial iridium oxide anodes on system durability.

Abouremeleh, Mohammed H. [Lawrence Berkeley Nation↗
DOE OSTI2021

Photoelectrochemically Self Improving Si/GaN Photocathode: Figure 1a Raw Data

10 hours chronoamperometry (CA) testing under 1 sun illumination and constant bias at -0.6 V vs RHE, the corresponding Faradaic efficiency reveals a self-improving nature of GaN, inset: CA testing on bare Si for 5 hours under 1 sun illumination and -0.6 V vs RHE, this bare Si photocathode rapidly drops down to < 0.05 mA/cm2 within an hour. Both CA testing performed in 0.5 M H2SO4 (pH=0.4).

photocathode↗
DOE OSTI2020

Low temperature, ambient pressure electrochemical ammonia synthesis in alkaline media — Mechanistic studies and catalyst design. Final Report

Ammonia synthesis via the Haber-Bosch process is a pillar of modern agriculture, which converts the abundant but inert dinitrogen in the atmosphere to nitrogen-based fertilizers. Despite more than a century of optimization, the Haber-Bosch process remains energy intensive and reliant on fossil fuels and produces large amounts of CO 2 . Distributed and modular ammonia synthesis via the electrochemical nitrogen reduction reaction (ENRR) at or close to ambient conditions, powered by renewable electricity is an attractive alternative because it allows as needed production of ammonia, and in turn fertilizers. However, selective ENRR catalysts remain lacking. In this project, we systematically investigated two categories of catalytic materials, i.e., precious metals and transition metal nitrides, in the ENRR. Precious metals exhibit low activity and selectivity in the ENRR, which is in agreement with recent computational studies. Transition metal nitrides, especially VN, has been demonstrated as active and selective ENRR catalysts. We developed the first quantitative method to determine the amount of ammonia produced in the ENRR on N-containing containing catalysts in the membrane electrode assembly configuration. An initial ammonia production rate of 6.6 × 10 -10 mol s -1 mg -1 and a Faradaic efficiency of 6.0% at -0.1 V were reached on VN. After the initial deactivation, VN was shown to be stable in the ENRR for 116 hours with a steady state ammonia production rate of 1.1 × 10 -10 mol s -1 cm -2 . A vanadium oxynitride species was identified as the active phase in the ENRR via a combination of operando and ex situ characterization techniques. In addition, we established that the ENRR proceeded on transition metal nitrides via the Mars van Krevelen mechanism and determined the initial and steady state active site densities by developing a quantitative isotopic exchange method.

42 ENGINEERING↗
DOE OSTI2020

Peptide Control of Electrocatalyst Surface Environment and Catalyst Structure: A Design Platform to Enable Mechanistic Understanding and Synthesis of Active and Selective N2 Reduction Catalysts

Low-temperature electrochemical ammonia synthesis with heterogeneous catalysts suffers from extremely low Faradaic efficiencies (< 1%). The hydrogen evolution reaction (HER) is predicted and experimentally demonstrated to outcompete the nitrogen reduction reaction (N2RR). Meanwhile, the nitrogenase enzymes found in nature enable selective N2RR at Fe/Mo metal centers. Montoya and co-authors suggest that a successful transition metal N2RR catalyst will deviate from or completely circumvent current linear scaling relationships. We propose an approach where short-chain peptides (3-20 amino acids) will be used to control the local surface environment of catalysts. This peptide-based design strategy will be used to overcome HER selectivity and the limitations of *NxHy adsorbate scaling.

08 HYDROGEN↗
DOE OSTI2023

Intensified Catalytic Conversion of CO2 into High Value Chemicals

The utilization of CO2 produced from power generation plants as a feedstock for creating new valuable products offers a strategy to reduce GHG emissions, offset carbon capture costs, and facilitate the rebalancing of the carbon cycle. After considering the thermodynamic requirement of potential products from CO2 utilization and their market size, formic acid is a desirable target that offers widespread utility in industrial chemical production and chemical energy storage as a liquid fuel. To effectively utilize CO2 from power generation plants, UK proposes an enhanced bimetallic oxide carbon utilization process (EBOCU) that enables electrochemical CO2 conversion to formic acid. The UK intensified electrocatalytic process combines three main components: 1) a novel bimetallic oxide electrocatalyst; 2) a stable electrochemical reactor using robust electrodes; and 3) a pressurized electrochemical reactor. The output from this project showed the economic viability of producing high-value formic acid from CO2 to both offset the cost associated with post-combustion CCS and reduce GHG emissions. This project developed and screened a series engineered catalysts to selectively reduce CO2 directly to formic acid. The best performing catalyst based on formic acid production, stability, and Faradaic efficiency, was immobilized on carbon electrodes, and tested inside a flow through reactor. After lab-scale testing was completed, the experimental data was used to perform a Life-Cycle Analysis (LCA) and conduct an Initial Technical and Economic Feasibility Study. The LCA showed a pathway to a net negative CO2 utilization process with the incorporation of renewable energy, while the TEA showed the potential to produce formic acid below the current commercial price. The UK EBOCU process was successfully demonstrated at the TRL3 level and has a clear pathway to further development and contribution to the nation’s ambitious decarbonization goals.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Growth of Well-Defined Model Catalysts for Electrochemistry: From Surface Science Studies to Electrocatalytic CO2 Conversion

We combined ultrahigh vacuum (UHV) surface science techniques, electrochemical measurements, and computational modeling to investigate electrocatalytic systems that are crucial components of the carbon management effort, including oxygen evolution reactions (OER) and CO2 reduction reactions (CO2RR). Well-defined Model catalysts were grown on substrates in the UHV chamber and characterized with X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM). Selected model electrocatalysts were then tested in electrochemical cells to establish the structure-property relationships in OER and CO2RR. Our results showed that the edge sites of Fe2O3 grown on Au(111) were the most active toward OER and incorporation of Ni at the edge sites (NiFeOx) further boosted their OER activity. We also resolved the size-dependent electrocatalytic CO2-to-CO conversion of the Ag nanoparticle electrocatalysts with average particle diameter between 2 to 6 nm: smaller diameter (< 3 nm) particles favored H2 evolution reaction (HER) due to a high population of Ag edge sites, whereas larger diameter particles favored CO2RR as the population of Ag(100) surface sites grew. We further discovered that electronic interactions between small diameter Ag particles and highly defective carbon supports could break the size-dependent CO2RR selectivity, resulting in highly selective (CO Faradaic Efficiency > 90%) and active Ag nanoparticle electrocatalysts with sizes < 2 nm diameter.

Deng, Xingyi↗
DOE OSTI2024

Sulfur-Doped Carbon Support Boosts CO2RR Activity of Ag Electrocatalysts

For presentation at the 70th AVS International Symposium and Exhibition. In this work, we show that the activity of Ag electrocatalysts for electrochemical CO2 to CO conversion is improved when supported on sulfur-doped (S-doped) carbon materials. S-doped carbon support was created by treating the heavily sputtered, highly oriented pyrolytic graphite (HOPG) in H2S at elevated temperatures, as confirmed by the S 2p X-ray photoelectron spectroscopy (XPS) peak. Scanning tunneling microscopy (STM) images indicated that Ag nanoparticles supported on S-doped HOPG had similar size distributions as those supported on sulfur-free (S-free) HOPG. While both catalysts reached > 90% CO Faradaic efficiency (FECO) at E = -1.3 V vs. the reversible hydrogen electrode (RHE) in the CO2 reduction reaction (CO2RR), Ag catalysts supported on S-doped HOPG demonstrated 70% higher CO turnover frequency (TOFCO = 3.4 CO/atomAg/s) than those supported on S-free HOPG (TOFCO = 2.0 CO/atomAg/s). Preliminary calculations based on density functional theory (DFT) indicated a more favorable energetic pathway of CO2-to-CO at the C-S-Ag interface, tentatively consistent with experiments. These results hint at a new approach to design active and selective electrocatalysts for CO2 conversion.

Deng, Xingyi↗
DOE OSTI2025

Understanding of Ag Nanocatalysts for Electrocatalytic CO2 Conversion: Effects of Particle Size and Carbon Support

In this talk, we combined ultrahigh vacuum (UHV) surface science techniques, electrochemical measurements, and computational modeling to investigate Ag based electrocatalysts for CO2 reduction reaction (CO2RR). Our goal is to understand the critical characteristics governing the activity and selectivity of Ag electrocatalysts. Ag electrocatalysts were grown on highly oriented pyrolytic graphite (HOPG) in the UHV chamber, characterized with X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM), and then tested in a custom-built gastight H-cell. Supported by computational modeling based on density functional theory (DFT) calculations and microkinetic modeling (MKM), our studies revealed a strong size-dependent electrocatalytic CO2-to-CO conversion of the Ag nanoparticle electrocatalysts with average particle diameter between 2 to 6 nm. Smaller diameter (< 3 nm) particles favored H2 evolution reaction (HER) due to a high population of Ag edge sites, whereas larger diameter particles favored CO2RR as the population of Ag(100) surface sites grew. We further discovered that electronic interactions between small diameter Ag particles and highly defective carbon supports could break the size-dependent CO2RR reactivity, resulting in highly selective (CO Faradaic Efficiency > 90%) and active Ag nanoparticle electrocatalysts with sizes < 2 nm diameter. This knowledge is key to understand electrocatalysts performance and to ultimately guide electrocatalyst design

Ag nanoparticles↗
DOE OSTI2025

Optimization of Ag Electrocatalyst Performance for CO2 to CO Conversion: Pairing Atomic Simulations with Experiments

Density-functional theory- based calculations that complement our series of experimental efforts on optimizing Ag electrocatalyst performance for CO2 to CO conversion were presented. Three key findings are drawn out from the combined UHV surface science, STM and electrochemical measurements: (1) Using a series of Ag nanoparticles with 2-6 nm average diameters, CO2 reduction reaction (CO2RR) activity increases, with particle between 2 nm and ∼4 nm demonstrating the highest combination of activity and selectivity; (2) Electronic metal−support interactions (EMSIs) between Ag and C dramatically improve CO2RR performance as evidenced by a scaling relationship between particle size and the relative Ag−C EMSIs strength, which improves the CO2-to-CO Faradaic efficiency of sub-2 nm Ag particles from 2 to ∼100% and increases the CO turnover frequency ∼15-fold compared with similarly sized bare Ag particles; (3) The performance Ag electrocatalysts is improved when supported on S-doped C materials. Computational modeling of 1−10 nm Ag particles predicts a nearly identical size-dependent trend with maximum CO2RR activity predicted for 3.7nm particles. The calculations support the promotional effect of C materials, showing a large charge transfer of 1.02 e from Ag clusters to defective C and a 0.41 eV less endergonic step of forming COOH intermediate on Ag/defective-C compared to the Ag/C system. Calculations indicate a more favorable energetic pathway of CO2-to-CO at the C-S-Ag interface, consistent with experiments.

CO2 utilization↗
DOE OSTI2022

Few-Atom Copper Catalyst for the Electrochemical Reduction of CO to Acetate: Synergetic Catalysis between Neighboring Cu Atoms

Single-atom catalysts (SACs) are gaining increasing recognition because of their superior catalytic properties for various reactions. However, the performance of SACs is often limited by the lack of neighboring metal centers to cooperate in catalysis. Herein, a synergetic interaction between neighboring Cu atoms of a few-atom catalyst (FAC) on graphdiyne is found to greatly enhance the production of acetate in CO electroreduction reaction relative to Cu SACs. In a 1.0 M KOH electrolyte, this Cu FAC exhibits an acetate Faradaic efficiency of 53.8±1.5 % and an ultrahigh relative purity of up to 97 wt% for liquid products, and excellent stability of over 23 h continuous electrolysis at -0.8 V versus reversible hydrogen electrode (RHE). Theoretical studies suggest that the intersite catalytic communication between two neighboring metal atoms confined in each pore of GDY facilitates the formation of acetic acid through either stepwise hydrogenation of CH 2 CO* or the direct reaction of H 2 O with CH 2 CO*. Our study demonstrates the unprecedented synergetic catalysis of Cu FAC in promoting the selective CO electroreduction toward acetate production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Measurement of ion transport properties in ion exchange membranes for photoelectrochemical water splitting

Photoelectrochemical (PEC) water-splitting systems have the unique ability to produce renewable hydrogen directly from sunlight, independent of the electrical grid. These systems are therefore appealing technological options for resilient long-term energy storage. Ion selective membranes, such as monopolar and bipolar membranes, are a vital component of PEC water-splitting systems. These membranes allow for ionic conduction between the cathode and anode chambers, separation of products, and improved catalyst environments for reactions. In order to measure key properties and to study the performance of these ion exchange membranes, it is imperative to develop a robust testing protocol that can be used across the field. This paper introduces two standard electrochemical cells designed to directly measure ion transport properties in monopolar and bipolar membranes. The first electrochemical cell uses commercially available Pt disk electrodes to preform electrochemical impedance spectroscopy (EIS) and reliably measure through-plane conductivity of monopolar membranes. The second electrochemical cell uses four-point measurements with Luggin capillaries and a series of membrane configurations to perform current density-voltage and Faradaic efficiency (FE) measurements for water dissociation (WD) reactions on bipolar membranes. The cell designs and techniques laid out below allow for accurate measurement of ion transport parameters in ion exchange membranes, direct comparison of membranes being developed across the field, and in turn, greater advancements in ion exchange membranes and PEC water-splitting systems.

cation exchange membrane↗
DOE OSTI2020

A Review of the Use of Immobilized Ionic Liquids in the Electrochemical Conversion of CO2

This paper is a review on the application of imidazolium-based ionic liquids tethered to polymer backbones in the electrochemical conversion of CO2 to carbon monoxide and formic acid. These tethered ionic liquids have been incorporated into novel anion ion exchange membranes for CO2 electrolysis, as well as for ionomers that have been incorporated into the cathode catalyst layer, providing a co-catalyst for the reduction reaction. In using these tethered ionic liquids in the cathode catalyst composition, the cell operating current increased by a factor of two or more. The Faradaic efficiencies also increased by 20–30%. This paper provides a review of the literature, in addition to providing some new experimental results from Dioxide Materials, in the electrochemical conversion of CO2 to CO and formic acid.

09 BIOMASS FUELS↗
DOE OSTI2023

New Platinum Complexes from Salen- and Hydroxy-Substituted Salpn-Naphthalene Ligands with CO 2 Reduction Activity

The electrocatalytic reduction of carbon dioxide (CO 2 ) into added-value products is a promising alternative to completing the cycle of atmospheric CO 2 . We report two new platinum complexes—a salen-like naphthalene (PtL1) and a hydroxy-substituted salpn naphthalene (PtL2)—that are capable of activating CO 2 to produce carbon monoxide (CO). The predominant keto tautomer of the non-innocent ligands was determined using DFT calculations and UV-Vis spectroscopy. The PtL2 complex has a CO Faradaic efficiency >40% in the presence of water as a sacrificial proton source at -2.5 V vs. Fc/Fc + . The addition of the hydroxy group in combination with water as a proton source decreased the reduction potential and increased the CO formation tenfold when compared to PtL1.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Ligand Tuning in Cu(pyalk)2 Water Oxidation Electrocatalysis

Molecular copper water oxidation electrocatalysts have been extensively studied in recent years for their potential use in artificial photosynthetic systems for solar energy conversion. Although ligand modification and its ability to influence catalytic properties is a key advantage of molecular systems, there are, as yet, few examples of systematic studies of these effects. Our oxidatively resistant pyalk (2-pyridyl-2-propanoate) ligand forms a complex with copper(II) that catalyzes water oxidation and provides an attractive scaffold for systematic ligand tuning. Here, we report a series of analogous copper complexes with electron-donating (methoxy-) and -withdrawing (methoxycarbonyl-) groups at the para-position of the pyalk ligand. Trends in the pKa and redox potential align with first-principles predictions for the electron-withdrawing and electron-donating groups. While the modified complexes show good activity for water oxidation, lowered faradaic efficiency in comparison to the parent complex highlights the importance of stability considerations for catalyst tuning.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1984

A mathematical model for the iron/chromium redox battery

A mathematical model has been developed to describe the isothermal operation of a single anode-separator-cathode unit cell in a redox-flow battery and has been applied to the NASA iron/chromium system. The model, based on porous electrode theory, incorporates redox kinetics, mass transfer, and ohmic effects as well as the parasitic hydrogen reaction which occurs in the chromium electrode. A numerical parameter study was carried out to predict cell performance to aid in the rational design, scale-up, and operation of the flow battery. The calculations demonstrate: (1) an optimum electrode thickness and electrolyte flow rate exist; (2) the amount of hydrogen evolved and, hence, cycle faradaic efficiency, can be affected by cell geometry, flow rate, and charging procedure; (3) countercurrent flow results in enhanced cell performance over cocurrent flow; and (4) elevated temperature operation enhances cell performance.

Fedkiw, P. S.↗
NASA NTRS1992

Polymeric Electrolyte Containing 12-Crown-4 Ether

Experiments show incorporation of 12-crown-4 ether into solid electrolytes based on polyethylene oxide enhances their electrochemical properties. More specifically, 12-crown-4 ether increases Faradaic efficiency for Li+ ions in low-power secondary Li cells and enables operation of these cells at lower temperatures with higher efficiencies.

Nagasubramanian, Ganesa↗
NASA NTRS1992

Post-treatment of reclaimed waste water based on an electrochemical advanced oxidation process

The purification of reclaimed water is essential to water reclamation technology life-support systems in lunar/Mars habitats. An electrochemical UV reactor is being developed which generates oxidants, operates at low temperatures, and requires no chemical expendables. The reactor is the basis for an advanced oxidation process in which electrochemically generated ozone and hydrogen peroxide are used in combination with ultraviolet light irradiation to produce hydroxyl radicals. Results from this process are presented which demonstrate concept feasibility for removal of organic impurities and disinfection of water for potable and hygiene reuse. Power, size requirements, Faradaic efficiency, and process reaction kinetics are discussed. At the completion of this development effort the reactor system will be installed in JSC's regenerative water recovery test facility for evaluation to compare this technique with other candidate processes.

Verostko, Charles E.↗
NASA NTRS2001

Electrodeposition of Low Stress Nickel Phosphorous Alloys for Precision Component Fabrication

Nickel alloys are favored for electroforming precision components. Nickel phosphorous and nickel cobalt phosphorous are studied in this work. A completely new and innovative electrolytic process eliminates the fumes present in electroless processes and is suitable for electroforming nickel phosphorous and nickel cobalt phosphorous alloys to any desirable thickness, using soluble anodes, without stripping of tanks. Solutions show excellent performance for extended throughput. Properties include, cleaner low temperature operation (40 - 45 C), high Faradaic efficiency, low stress, Rockwell C 52 - 54 hardness and as much as 2000 N per square millimeter tensile strength. Performance is compared to nickel and nickel cobalt electroforming.

Engelhaupt, Darell↗