Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLANGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Sound radiation from hyperboloidal inlet ducts

This paper presents rigorous solutions for the problem of sound radiation from various inlet ducts including hyperboloidal (or hyperbolic) inlet ducts and circular ducts with wide flange. The numerical results include the complex conversion (or reflection) coefficients and the radiation directivity for the various incident wave modes - spinning modes as well as axisymmetric modes. The analysis utilizes hyperboloidal wave functions which are defined here as a class of eigensolutions of the wave equation for oblate spheroidal coordinates, and is valid for the whole frequency range including frequencies above and below the cutoff frequencies of duct modes involved.

Cho, Y. C.↗
NASA NTRS1979

Mass Driver Two - Cryogenic module

The cryogenic module of Mass Driver Two comprises a 3.25 inch (82.55 mm) OD bucket with two 44 kilo-ampere-turn coils made with .028 inch (.71 mm) diam niobium-titanium multi-filamentary cable in a copper matrix, impregnated with lead alloy for thermal inertia, as well as the service station to refrigerate, energize and eject the bucket. The station is housed in a six inch flanged pyrex cross which connects to the four inch pyrex tube of the mass driver itself. The bucket is refrigerated by being forced against a copper braid cradle attached to the bottom of a liquid helium reservoir which protrudes into the cross from above. The bucket is energized inductively by turning off two superconducting coils which are also attached to the helium reservoir, and which have maintained the correct flux linkage through the bucket coils during their cool-down through the critical temperature. Once charging is completed, the clamping pressure is released and the bucket is injected into the mass driver by means of two normal-conductor pulse coils surrounding the horizontal branches of the cross.

Fine, K.↗
NASA NTRS1980

Shaping graphite/epoxy stiffeners

Layers of graphite/epoxy, tape stacked on ridges and in grooves of channel like ribs stiffen curved laminates. Twenty-five to 38 layers of tape on each cap and flange are vacuum-bagged into shape and then interleaved with plies of fabric to form light-weight structural members free of wrinkles and voids. Structure could be parts for cars, trucks, and other vehicles.

Cupp, J. L.↗
NASA NTRS1981

Spiral-wound gasket forms low-temperature seal

Spiral-wound cryogenic gasket with one component requires no encapsulant and is easily produced with self-locking features. Seal either opens and closes or is fixed. It is made by skiving strip from circumference of disk of glass-filled material. Successive turns of strip are spirally wrapped in groove machined into one flange surface. Closing joint compresses gasket.

Irick, S. C.↗
NASA NTRS1979

High speed cylindrical rolling element bearing analysis 'CYBEAN' - Analytic formulation

This paper documents the analytic foundation and software architecture for the computerized mathematical simulation of high speed cylindrical rolling element bearing behavior. The software, CYBEAN (CYlindrical BEaring ANalysis), considers a flexible, variable geometry outer ring, EHD films, roller centrifugal and quasidynamic loads, roller tilt and skew, mounting fits, cage and flange interactions. The representation includes both steady state and time transient simulation of thermal interactions internal to and coupled with the surroundings of the bearing. A sample problem illustrating program use is presented.

Kleckner, R. J.↗
NASA NTRS1982

Electrically-conductive Low-Permeability Pressure Seal

Metal-plated butyl rubber seal has been devised for enclosures of electronic equipment that must be maintained under dry, inert atmosphere. Seal prevents gas leakage over prolonged periods, while conductivity suppresses electromagnetic emissions from sealed equipment. Seal is formed by depositing aluminum or gold onto molded-in-place butyl rubber gasket and surrounding areas of flange.

Krieg, H. C.↗
NASA NTRS1978

Space fabrication demonstration system

The lower right aluminum beam cap roll forming mill was delivered and installed in the beam builder. The beam was brought to full operational status and beams of one to six bay lengths were produced to demonstrate full system capability. Although the cap flange waviness problem persists, work is progressing within cost and schedule.

Source record↗
NASA NTRS1981

High temperature solar receiver

The development of a high temperature solar thermal receiver is described. A prototype receiver and associated test support (auxiliary) hardware was fabricated. Shakedown and initial performance tests of the prototype receiver were performed. Maximum outlet temperatures of 1600 F were achieved at 100% solar (70-75 kW) input power with 900 F inlet temperatures and a subsequent testing was concluded by a 2550 F outlet run. The window retaining assembly was modified to improve its tolerance for thermal distortion of the flanges. It is shown that cost effective receiver designs can be implemented within the framework of present materials technology.

Source record↗
NASA NTRS1981

Improved cooling design for high power waveguide system

Testing of X band high power components in a traveling wave resonator indicates that this improved cooling design reduces temperature in the waveguide and flange. The waveguide power handling capability and power transmission reliability is increased substantially.

Chen, W. C. J.↗
NASA NTRS1980

Thermal fatigue performance of integrally cast automotive turbine wheels

Fluidized bed thermal fatigue testing was conducted on 16 integrally cast automotive turbine wheels for 1000-10,000 (600 sec total) thermal cycles at 935/50 C. The 16 wheels consisted of 14 IN-792 + 1% Hf and 2 gatorized AF2-1DA wheels; 6 of the IN-792 + Hf wheels contained crack arrest pockets inside the blade root flange. Temperature transients during the thermal cycling were measured in three calibration tests using either 18 or 30 thermocouples per wheel. Thermal cracking based on crack length versus accumulated cycles was greatest for unpocketed wheels developing cracks in 8-13 cycles compared to 75-250 cycles for unpocketed wheels. However, pocketed wheels survived up to 10,000 cycles with crack lengths less than 20 mm, whereas two unpocketed wheels developed 45 mm long cracks in 1000-2000 cycles.

Humphreys, V. E.↗
NASA NTRS1982

Pipe-Thread Vacuum Seal

Lead/tin solder coating on pipe threads serves as seal in non-critical vacuum systems. Pipe-thread seal is less expensive than weld or knife-edge flanges. Can also be used in place of sealing tape.

Chandler, J. A.↗
NASA NTRS1983

Explosive Joining for Nuclear-Reactor Repair

In explosive joining technique, adapter flange from fuel channel machined to incorporate a V-notch interface. Ribbon explosive, 1/2 inch (1.3 cm) in width, drives V-notched wall of adapter into bellows assembly, producing atomic-level metallurgical bond. Ribbon charge yields joint with double parent metal strength.

Bement, L. J.↗
NASA NTRS1982

Some properties of NiH2 cells

Different tests on a flight type cell are discussed. The temperature was measured at the cell flange. The cell was charged to rollover at .75 C rate at 40 degrees C for the first temperature. At that point a voltage reading was taken. Charging was done for an arbitrary ten seconds at .75 C, 30 C, 20 C, 10 C and zero C to obtain momentarily stable voltages.

Rogers, H. H.↗
NASA NTRS1980

Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 1: Analysis

The models and associated mathematics used within the SPHERBEAN computer program for prediction of the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings are presented. The analysis allows six degrees of freedom for each roller and three for each half of an optionally split cage. Roller skew, free lubricant, inertial loads, appropriate elastic and friction forces, and flexible outer ring are considered. Roller quasidynamic equilibrium is calculated for a bearing with up to 30 rollers per row, and distinct roller and flange geometries are specifiable. The user is referred to the material contained here for formulation assumptions and algorithm detail.

Kleckner, R. J.↗
NASA NTRS1982

Evaluation of waveguide coating materials

Waveguide coating materials were tested at 8470 MHz for insertion loss. Samples of these coatings on waveguide pieces without flanges were tested in an environmental chamber to simulate the effects of high power microwave heating. Test results indicated that three types of coating materials are acceptable with regard to insertion loss. However, simulated microwave heating caused debonding of Metcot 7 and BD-991 coatings, resulting in peelings in the waveguide. The higher cost Chemglaze R104 does not exhibit this problem.

Chen, W. C. J.↗
NASA NTRS1982

Spiral slotted phased antenna array

A flush mounting, cavity-backed, dual orthogonal slot antenna for aircraft and space vehicles is described. Improved radiation pattern characteristics are obtained by making the spiral slot pattern elliptical in the aperture plane. A cavity and a flanged aperture plate are configured such that one slot pair is orthogonal with respect to another slot pair within the aperture plate. Coaxial split-tube baluns are used to drive the junctions between corresponding slot pairs. An optional cavity dielectric is provided and a drive coupling arrangement includes a four port comparator hybrid having sum and difference ports respectively, for alternate excitation to produce a single lobe or a double lobe pattern with null. Switching apparatus is provided to connect a common terminal to either of the ports.

Ellis, H., Jr.↗
NASA NTRS1982

Automated optimum design of wing structures. Deterministic and probabilistic approaches

The automated optimum design of airplane wing structures subjected to multiple behavior constraints is described. The structural mass of the wing is considered the objective function. The maximum stress, wing tip deflection, root angle of attack, and flutter velocity during the pull up maneuver (static load), the natural frequencies of the wing structure, and the stresses induced in the wing structure due to landing and gust loads are suitably constrained. Both deterministic and probabilistic approaches are used for finding the stresses induced in the airplane wing structure due to landing and gust loads. A wing design is represented by a uniform beam with a cross section in the form of a hollow symmetric double wedge. The airfoil thickness and chord length are the design variables, and a graphical procedure is used to find the optimum solutions. A supersonic wing design is represented by finite elements. The thicknesses of the skin and the web and the cross sectional areas of the flanges are the design variables, and nonlinear programming techniques are used to find the optimum solution.

Rao, S. S.↗
NASA NTRS1982

Space storable propulsion components development

The current development status of components to control the flow of propellants (liquid fluorine and hydrazine) in a demonstration space storable propulsion system is discussed. The criteria which determined the designs for the pressure regulator, explosive-actuated valves, propellant shutoff valve, latching solenoid-actuated valve and propellant filter are presented. The test philosophy that was followed during component development is outlined. The results from compatibility demonstrations for reusable connectors, flange seals, and CRES/Ti-6Al4V transition tubes and the evaluations of processes for welding (hand-held TIG, automated TIG, and EB), cleaning for fluorine service, and decontamination after fluorine exposure are described.

Hagler, R., Jr.↗