Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “F STACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Oxygen separation from air using zirconia solid electrolyte membranes

Air separation using a zirconia solid electrolyte membrane is a possible alternative source of oxygen. The process of zirconia oxygen separation is reviewed, and an oxygen plant concept using such separation is described. Potential cell designs, stack designs, and testing procedures are examined. Fabrication of the materials used in a zirconia module as well as distribution plate design and fabrication are examined.

Suitor, J. W.↗

Lanthanum Strontium Cobaltite-Alumina Fiber Composite Contact Material for Solid Oxide Fuel Cells

Short alumina fibers were added to LSCo contact material to enhance the contact strength and improve thermal cycle stability. Alumina fiber from 2.5 v% to 20 v% were mixed with LSCo and sintered at elevated temperatures. Sintering study showed retardation in densification of LSCo matrix with increasing alumina content. Sintered bulk strength exhibited similar behavior where strength greatly reduced at high alumina v%. Coefficient of thermal expansion showed consistent results with prediction from rule of mixture. Contact strength using anode supported YSZ bilayer coupons improved greatly with the presence of small amount (2.5-5 v%) alumina fibers and no substantial reduction after 10 deep thermal cycles. Candidate LSCo-Al2O3 contact materials was validated in a generic stack test fixture for 1000h at 800oC followed by 10 thermal cycles. Results of impedance analysis showed substantial improvement in thermal cycle stability as compared to LSCo parent materials.

SOFC cathode, strength, LSCo, alumina↗

The cluster compound In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} containing Mo{sub 14} clusters and the new mono- and bi-capped trioctahedral Mo{sub 15} and Mo{sub 16} clusters: Synthesis, crystal structure, and electrical and magnetic properties

Single crystals of the new quaternary compound In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} were obtained by solid state reaction. The crystal structure was determined by single-crystal X-ray diffraction. In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} crystallizes in the orthorhombic space group Pbca with unit-cell parameters a=9.4432(14) Å, b=11.4828(12) Å, c=20.299(4) Å and Z=4. Full-matrix least-squares refinement on F{sup 2} using 3807 independent reflections for 219 refinable parameters resulted in R{sub 1}=0.0259 and wR{sub 2}=0.0591. The crystal structure contains in addition to Mo{sub 14} clusters the first examples of mono- and bi-capped trioctahedral Mo{sub 14} i.e. Mo{sub 15} and Mo{sub 16} clusters. The oxygen framework derives from a stacking along the a direction of close-packed layers with sequence (…ABAC…). The Mo–Mo distances range between 2.6938(5) and 2.8420(6) Å and the Mo–O distances between 1.879(5) and 2.250(3) Å, as usually observed in molybdenum oxide clusters. The indium atoms form In{sub 4}{sup 6+} bent chains with In–In distances of 2.6682(5) and 2.6622(8) Å and the Ti atoms are in highly distorted octahedral sites of oxygen atoms with Ti–O distances ranging between 1.865(4) and 2.161(4) Å. Magnetic susceptibility measurements confirm the presence of Ti{sup 4+} cations and the absence of localized moments on the Mo network. Electrical resistivity measurements on a single crystal of In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} show a semimetallic behavior. - Graphical abstract: We present here the synthesis, the crystal structure, and the electrical and magnetic properties of the new compound In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} in which Mo{sub 14} clusters coexist statistically with mono- and bi-capped trioctahedral Mo{sub 14} that is Mo{sub 15} and Mo{sub 16} clusters. - Highlights: • Single crystals of In{sub 4}Ti{sub 1.5}Mo{sub 0.5}Mo{sub 14}O{sub 26} were obtained by solid state reaction. • The crystal structure contains Mo{sub 14}, Mo{sub 15} and Mo{sub 16} clusters. • The indium atoms form In{sub 4}{sup 6+} bent chains. • Poorly metallic behavior. • Absence of localized moments on the Mo network as well as on the Ti atoms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Insights into the Oxidant/Polymer Interfacial Growth of Vapor Phase Polymerized PEDOT Thin Films

Abstract The vapor phase polymerization (VPP) technique is used to produce thin films of poly(3,4‐ethylenedioxythiopene) (PEDOT) in which the Fe(III)Tosylate oxidant is altered. The oxidant is changed with the addition of an amphiphilic co‐polymer having different molecular weights, namely 2800 Da. and 5800 Da. Resulting PEDOT films produce conductivities of ≈1500 and ≈3000 S cm −1 respectively. Small angle X‐ray diffraction (SA‐XRD) indicates that the oxidant incorporating the larger molecular weight co‐polymer possesses ordered structure and that this in turn helps “template” the PEDOT during film formation. The structure and composition of the bottom (i.e. initial film formation) and top (i.e. final film formation) PEDOT surfaces are studied using surface sensitive analytical techniques; small angle X‐ray diffraction (SA‐XRD), ultraviolet photoelectron spectroscopy (UPS), 2D grazing incidence X‐ray diffraction (2D‐GIXD), metastable induced electron spectroscopy (MIES) and neutral impact collision ion scattering spectroscopy (NICISS). The results indicate that the increase in conductivity using the larger molecular weight co‐polymer additive is due to the film having larger lamella‐ and π‐stacking regions in addition to doping levels which remain unchanged throughout film formation. These conclusions are further supported by results obtained on a model PEDOT:Tosylate system using density functional theory (DFT) calculations.

Sharma, Anirudh↗

Emergent layer stacking arrangements in c-axis confined MoTe 2

The layer stacking order in 2D materials strongly affects functional properties and holds promise for next-generation electronic devices. In bulk, octahedral MoTe 2 possesses two stacking arrangements, the ferroelectric Weyl semimetal T d phase and the higher-order topological insulator 1T' phase. However, in thin flakes of MoTe 2 , it is unclear if the layer stacking follows the T d , 1T', or an alternative stacking sequence. Here, we use atomic-resolution scanning transmission electron microscopy to directly visualize the MoTe 2 layer stacking. In thin flakes, we observe highly disordered stacking, with nanoscale 1T' and T d domains, as well as alternative stacking arrangements not found in the bulk. We attribute these findings to intrinsic confinement effects on the MoTe 2 stacking-dependent free energy. Our results are important for the understanding of exotic physics displayed in MoTe 2 flakes. More broadly, this work suggests c-axis confinement as a method to influence layer stacking in other 2D materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of the nonlinear saturation of the gain on the peak modulation frequency in lasers based on self-assembled quantum dots

Peak modulation frequency of lasers based on self-organized quantum dots is calculated taking into account the effect of nonlinear gain saturation. Because of a large nonlinear gain coefficient and a reduction in the differential gain with increasing optical losses, the peak modulation frequency is attained for an optimum loss level that is significantly lower than the saturated optical gain in the active region. For lasers based on multiply stacked arrays of quantum dots, the peak modulation frequency first increases with increasing number of quantum-dot layers before leveling off, with the limiting value being inversely proportional to the nonlinear gain coefficient.

36 MATERIALS SCIENCE↗

Development of advanced fuel cell system, phase 2

A multiple task research and development program was performed to improve the weight, life, and performance characteristics of hydrogen-oxygen alkaline fuel cells for advanced power systems. Development and characterization of a very stable gold alloy catalyst was continued from Phase I of the program. A polymer material for fabrication of cell structural components was identified and its long term compatibility with the fuel cell environment was demonstrated in cell tests. Full scale partial cell stacks, with advanced design closed cycle evaporative coolers, were tested. The characteristics demonstrated in these tests verified the feasibility of developing the engineering model system concept into an advanced lightweight long life powerplant.

Handley, L. M.↗

Ultra high speed image processing techniques

Packaging techniques for ultra high speed image processing were developed. These techniques involve the development of a signal feedthrough technique through LSI/VLSI sapphire substrates. This allows the stacking of LSI/VLSI circuit substrates in a 3 dimensional package with greatly reduced length of interconnecting lines between the LSI/VLSI circuits. The reduced parasitic capacitances results in higher LSI/VLSI computational speeds at significantly reduced power consumption levels.

Anthony, T.↗

Thermal Analysis of Cryogenic Hydrogen Liquid Separator

During launch for the new Space Launch System (SLS) liquid hydrogen is bleed through the engines during replenish, pre-press, and extended pre-press to condition the engines prior to launch. The predicted bleed flow rates are larger than for the shuttle program. A consequence of the increased flow rates is having liquif hydrogen in the vent system, which the facilities was never designed to handle. To remedy the problem a liquid separator is being designed in the system to accumulated the liquid propellant and protect the facility flare stack (which can only handle gas). The attached document is a presentation of the current thermalfluid analysis performed for the separator and will be presented at the Thermal and Fluid Analysis Workshop (NASA workshop) next week in Cleveland, Ohio.

liquid separator↗

Weak Hard X-Ray Emission from Two Broad Absorption Line Quasars Observed with NuStar: Compton-Thick Absorption or Intrinsic X-Ray Weakness?

We present Nuclear Spectroscopic Telescope Array (NuSTAR) hard X-ray observations of two X-ray weak broad absorption line (BAL) quasars, PG 1004+130 (radio loud) and PG 1700+518 (radio quiet). Many BAL quasars appear X-ray weak, probably due to absorption by the shielding gas between the nucleus and the accretion-disk wind. The two targets are among the optically brightest BAL quasars, yet they are known to be significantly X-ray weak at rest-frame 2-10 keV (16-120 times fainter than typical quasars). We would expect to obtain approx. or equal to 400-600 hard X-ray (is greater than or equal to 10 keV) photons with NuSTAR, provided that these photons are not significantly absorbed N(sub H) is less than or equal to 10(exp24) cm(exp-2). However, both BAL quasars are only detected in the softer NuSTAR bands (e.g., 4-20 keV) but not in its harder bands (e.g., 20-30 keV), suggesting that either the shielding gas is highly Compton-thick or the two targets are intrinsically X-ray weak. We constrain the column densities for both to be N(sub H) 7 × 10(exp 24) cm(exp-2) if the weak hard X-ray emission is caused by obscuration from the shielding gas. We discuss a few possibilities for how PG 1004+130 could have Compton-thick shielding gas without strong Fe Kα line emission; dilution from jet-linked X-ray emission is one likely explanation. We also discuss the intrinsic X-ray weakness scenario based on a coronal-quenching model relevant to the shielding gas and disk wind of BAL quasars. Motivated by our NuSTAR results, we perform a Chandra stacking analysis with the Large Bright Quasar Survey BAL quasar sample and place statistical constraints upon the fraction of intrinsically X-ray weak BAL quasars; this fraction is likely 17%-40%.

nuclei↗

Circular polarisation characteristics of stacked microstrip antennas

Experimental results on the circular polarization (CP) characteristics of a two-layer electromagnetically coupled (EMCP) antenna are presented. Compared to the single CP patch antenna, the two-layer EMCP antenna with proper spacings can provide better axial ratio and directivity.

Lee, R. Q.↗

Deformation behavior and phase transformation of nanotwinned Al/Ti multilayers

We report nanotwinned Al/Ti multilayers have exhibited size-dependent microstructure evolution and high strength. However, their deformation mechanisms are less well understood. In this work, we investigated the deformation mechanisms of nanotwinned Al/Ti multilayers with FCC/HCP layer interfaces by using in situ micropillar compression tests. Nanotwinned Al/Ti multilayers exhibit compressive strength up to 2.4 GPa and good work hardening capability. Post-compression TEM analyses reveal high-density stacking faults and the HCP-to-FCC phase transformations in Ti. Molecular dynamics simulations elucidate the mechanisms of deformation induced phase transformation in Ti and the influence of collective movement of partial dislocations on the deformability of Al/Ti multilayers.

36 MATERIALS SCIENCE↗

Optimization of radiochromic film stacks to diagnose high-flux laser-accelerated proton beams

Here, we extend flatbed scanner calibrations of GafChromic EBT3, MD-V3, and HD-V2 radiochromic films using high-precision x-ray irradiation and monoenergetic proton bombardment. By computing a visibility parameter based on fractional errors, optimal dose ranges and transitions between film types are identified. The visibility analysis is used to design an ideal radiochromic film stack for the proton energy spectrum expected from the interaction of a petawatt laser with a cryogenic hydrogen jet target.

Curry, C. B. (ORCID:000000018756181X)↗

Biasing from galaxy trough and peak profiles with the DES Y3 redMaGiC galaxies and the weak lensing mass map

We measure the correspondence between the distribution of galaxies and matter around troughs and peaks in the projected galaxy density, by comparing redMaGiC galaxies (0.15 < z < 0.65) to weak lensing mass maps from the Dark Energy Survey (DES) Y3 data release. We obtain stacked profiles, as a function of angle θ, of the galaxy density contrast δ g and the weak lensing convergence κ, in the vicinity of these identified troughs and peaks, referred to as ‘void’ and ‘cluster’ superstructures. The ratio of the profiles depend mildly on θ, indicating good consistency between the profile shapes. We model the amplitude of this ratio using a function $F(\boldsymbol{\eta }, \theta )$ that depends on cosmological parameters $\boldsymbol{\eta }$, scaled by the galaxy bias. We construct templates of $F(\boldsymbol{\eta }, \theta )$ using a suite of N-body (‘Gower Street’) simulations forward-modelled with DES Y3-like noise and systematics. We discuss and quantify the caveats of using a linear bias model to create galaxy maps from the simulation dark matter shells. We measure the galaxy bias in three lens tomographic bins (near to far): $2.32^{+0.86}_{-0.27}, 2.18^{+0.86}_{-0.23}, 1.86^{+0.82}_{-0.23}$ for voids, and $2.46^{+0.73}_{-0.27}, 3.55^{+0.96}_{-0.55}, 4.27^{+0.36}_{-1.14}$ for clusters, assuming the best-fit Planck cosmology. Similar values with ∼0.1σ shifts are obtained assuming the mean DES Y3 cosmology. The biases from troughs and peaks are broadly consistent, although a larger bias is derived for peaks, which is also larger than those measured from the DES Y3 3 × 2-point analysis. This method shows an interesting avenue for measuring field-level bias that can be applied to future lensing surveys.

cosmology: observations↗

Method of forming a package for MEMS-based fuel cell

A MEMS-based fuel cell package and method thereof is disclosed. The fuel cell package comprises seven layers: (1) a sub-package fuel reservoir interface layer, (2) an anode manifold support layer, (3) a fuel/anode manifold and resistive heater layer, (4) a Thick Film Microporous Flow Host Structure layer containing a fuel cell, (5) an air manifold layer, (6) a cathode manifold support structure layer, and (7) a cap. Fuel cell packages with more than one fuel cell are formed by positioning stacks of these layers in series and/or parallel. The fuel cell package materials such as a molded plastic or a ceramic green tape material can be patterned, aligned and stacked to form three dimensional microfluidic channels that provide electrical feedthroughs from various layers which are bonded together and mechanically support a MEMS-based miniature fuel cell. The package incorporates resistive heating elements to control the temperature of the fuel cell stack. The package is fired to form a bond between the layers and one or more microporous flow host structures containing fuel cells are inserted within the Thick Film Microporous Flow Host Structure layer of the package.

30 DIRECT ENERGY CONVERSION↗

Electrostatic generator/motor electrodes located on the inner surface of an electromechanical battery rotor

A geometric design of E-S generator/motor electrodes mounted on the inner surface of a fiber-composite rotor is provided. The electrode configuration is able to sustain very high g levels. The rotor may be formed of carbon-fiber wound on top of an inner E or S-glass fiber composite core. The electrode design provides the needed area to satisfy the power requirements of the storage system and utilizes a stacked wedge-like electrode array that both solves the high-g problem and results in a doubling or tripling of the electrode area, relative to that of electrodes that conform to the inner cylindrical surface of the rotor.

42 ENGINEERING↗

Electrostatic generator/motor electrodes located on the inner surface of an electromechanical battery rotor

A geometric design of E-S generator motor electrodes mounted on the inner surface of a fiber-composite rotor is provided. The electrode configuration is able to sustain very high g levels. The rotor may be funned of carbon-fiber wound on top of an inner E car S-glass fiber composite core. The electrode design provides the needed area to satisfy the power requirements of the storage system and utilizes a stacked wedge-like electrode array that both solves the high-g problem and results in a doubling or tripling of the electrode area, relative to that of electrodes that conform to the inner cylindrical surface of the rotor.

25 ENERGY STORAGE↗

HEAVILY OBSCURED AGN IN STAR-FORMING GALAXIES AT z approx = 2

We study the properties of a sample of 211 heavily obscured active galactic nucleus (AGN) candidates in the extended Chandra Deep Field-South selecting objects with f {sub 24m}u{sub m}/f{sub R} > 1000 and R - K>4.5. Of these, 18 were detected in X-rays and found to be obscured AGNs with neutral hydrogen column densities of approx10{sup 23} cm{sup -2}. In the X-ray-undetected sample, the following evidence suggests a large fraction of heavily obscured (Compton-thick) AGN: (1) The stacked X-ray signal of the sample is strong, with an observed ratio of soft to hard X-ray counts consistent with a population of approx90% heavily obscured AGNs combined with 10% star-forming galaxies. (2) The X-ray-to-mid-IR ratios for these sources are significantly larger than that of star-forming galaxies and approx2 orders of magnitude smaller than for the general AGN population, suggesting column densities of N {sub H} approx> 5 x 10{sup 24} cm{sup -2}. (3) The Spitzer near- and mid-IR colors of these sources are consistent with those of the X-ray-detected samples if the effects of dust self-absorption are considered. Spectral fitting to the rest-frame UV/optical light (dominated by the host galaxy) returns stellar masses of approx10{sup 11} M{sub sun} and (E(B - V)) = 0.5, and reveals evidence for a significant young stellar population, indicating that these sources are experiencing considerable star formation. This sample of heavily obscured AGN candidates implies a space density at z approx 2 of approx10{sup -5} Mpc{sup -3}, finding a strong evolution in the number of L{sub X} >10{sup 44} erg s{sup -1} sources from z = 1.5 to 2.5, possibly consistent with a short-lived heavily obscured phase before an unobscured quasar is visible.

79 ASTRONOMY AND ASTROPHYSICS↗