Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrochemical analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Triacetic Acid Lactone and 4-Hydroxycoumarin as Bioprivileged Molecules for the Development of Performance-Advantaged Organic Corrosion Inhibitors

Biomass conversion, especially the development of bioprivileged molecules utilizing integration of biological and chemical processes, has shown potential to produce novel chemicals with enhanced properties. Here, organic corrosion inhibitors based on triacetic acid lactone and 4-hydroxycoumarin have been synthesized in good yield and tested for corrosion inhibition on mild steel in both sulfuric acid and hydrochloric acid. Sixteen novel corrosion inhibitors derived from triacetic acid lactone and 4-hydroxycoumarin were efficiently synthesized and twelve of them showed high corrosion inhibition efficiency as confirmed by electrochemical impedance spectroscopy (giving values greater than 78%) and polarization analysis. While triacetic acid lactone-based compounds showed good corrosion inhibition performance, the 4-hydroxycoumarin-based compounds showed further improvement in corrosion inhibition performance. Scanning electron microscopy (SEM) analysis of the mild steel coupon in the presence of selected inhibitors showed that corrosion was significantly diminished, with complementary X-ray photoelectron spectroscopy (XPS) analysis suggesting the inhibitor molecules strongly adsorbed on the steel surface. Quantum chemical calculations showed poor correlation between calculated parameters and the performance of these molecules. This large set of corrosion inhibitors containing a dozen promising corrosion inhibitors is useful for future rational design of corrosion inhibitors. In conclusion, the results demonstrate a new direction for the development of bioprivileged molecules.

09 BIOMASS FUELS↗
DOE OSTI2024

Nondestructive flash cathode recycling

Effective recycling of end-of-life Li-ion batteries (LIBs) is essential due to continuous accumulation of battery waste and gradual depletion of battery metal resources. The present closed-loop solutions include destructive conversion to metal compounds, by destroying the entire three-dimensional morphology of the cathode through continuous thermal treatment or harsh wet extraction methods, and direct regeneration by lithium replenishment. Here, we report a solvent- and water-free flash Joule heating (FJH) method combined with magnetic separation to restore fresh cathodes from waste cathodes, followed by solid-state relithiation. The entire process is called flash recycling. This FJH method exhibits the merits of milliseconds of duration and high battery metal recovery yields of ~98%. After FJH, the cathodes reveal intact core structures with hierarchical features, implying the feasibility of their reconstituting into new cathodes. Relithiated cathodes are further used in LIBs, and show good electrochemical performance, comparable to new commercial counterparts. Life-cycle-analysis highlights that flash recycling has higher environmental and economic benefits over traditional destructive recycling processes.

25 ENERGY STORAGE↗
DOE OSTI2022

Dynamics of particle network in composite battery cathodes

We report that improving composite battery electrodes requires a delicate control of active materials and electrode formulation. The electrochemically active particles fulfill their role as energy exchange reservoirs through interacting with the surrounding conductive network. We formulate a network evolution model to interpret the regulation and equilibration between electrochemical activity and mechanical damage of these particles. Through statistical analysis of thousands of particles using x-ray phase contrast holotomography in a LiNi 0.8 Mn 0.1 Co 0.1 O 2 -based cathode, we found that the local network heterogeneity results in asynchronous activities in the early cycles, and subsequently the particle assemblies move toward a synchronous behavior. Our study pinpoints the chemomechanical behavior of individual particles and enables better designs of the conductive network to optimize the utility of all the particles during operation.

25 ENERGY STORAGE↗
DOE OSTI2021

Manipulating meso-scale solvent structure from Pd nanoparticle deposits in deep eutectic solvents

Deep Eutectic Solvents (DESs) are complex solutions that present unique challenges compared to traditional electrolytes. Unlike most electrolytes and ionic liquids, DESs have delicate hydrogen bond networks that are responsible for their highly sensitive compositional dependence on the melting point. Prior work has demonstrated unique nanoscale structure both experimentally and theoretically that brings both challenges and opportunities to their adoption in traditional electrochemical processes. In this study, we use in-situ sample-rotated ultra-small angle X-ray scattering to resolve the near-interface solvent structure after electrodepositing Pd nanoparticles onto a glassy carbon electrode in choline chloride:urea and choline chloride:ethylene glycol DESs. Our results indicate that solvent structure can be observed on the meso-scale in the choline chloride:urea and choline chloride:ethylene glycol systems. Importantly, this extended solvent structure peaks at -0.5 V (vs. Ag/AgCl) and decreases slightly with higher overpotentials during Pd electrodeposition. Experimentally, the nature of this structure is more pronounced in the ethylene glycol system, as evidenced by both the X-ray scattering as well as the electrochemical impedance spectroscopy (EIS). Here, molecular dynamics simulations and dipolar orientation analysis reveal that chloride delocalization near the Pd interface and long-range interactions between the choline and each hydrogen bond donor are very different and qualitatively consistent with the experimental data. These results show how the long-range solvent-deposit interactions can be tuned by changing the hydrogen bond donor in the DES and the applied potential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A Cost-Performance Analysis of a Sodium Heat Engine for Distributed Concentrating Solar Power

We present that a sodium thermal electrochemical converter (Na-TEC) generates electricity directly from heat through isothermal expansion of sodium ions across a beta"-alumina solid-electrolyte. This heat engine has been considered for use with conventional concentrating solar power (CSP) systems before. However, unlike previous single-stage devices, the improved design uses two stages with an interstage reheat, allowing more economical and efficient conversion up to 29% at a hot side temperature of 850 °C. Herein, a cost-performance analysis for this improved design assesses opportunities for distributed-CSP in the context of micro-combined heat and power systems. A high-level techno-economic analysis (TEA) is presented that explores four scenarios where a Na-TEC is used as the heat engine for a distributed-CSP system. Overnight capital cost and levelized cost of electricity (LCOE) are estimated for a system lifetime of 30 years, revealing that overnight capital costs in a range from $3.57 to $17.71 per W e are feasible, which equate to LCOEs from 6.9 to 17.2 cents kWh e -1 . This analysis makes a significant contribution by concurrently quantifying the efficiency and unit costs for a range of multistage configurations, and demonstrating that a Na-TEC may be a promising alternative to Stirling engines for distributed-CSP systems at residential scale of 1–5 kW e .

14 SOLAR ENERGY↗
DOE OSTI2021

Redox Mediated Control of Electrochemical Potential in Liquid Cell Electron Microscopy

Liquid cell electron microscopy enables the study of nanoscale transformations in solvents with high spatial and temporal resolution, but for the technique to achieve its potential requires a new level of control over the reactivity caused by radical generation under electron beam irradiation. An understanding of how to control electron-solvent interactions is needed to further advance the study of structural dynamics for complex materials at the nanoscale. Additionally, we developed an approach that scavenges radicals with redox species that form well-defined redox couples and control the electrochemical potential in situ . This approach enables the observation of electrochemical structural dynamics at near-atomic resolution with precise control of the liquid environment. Analysis of nanocrystal etching trajectories indicates that this approach can be generalized to several chemical systems. The ability to simultaneously observe heterogeneous reactions at near-atomic resolution and precisely control the electrochemical potential enables the fundamental study of complex nanoscale dynamics with unprecedented detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Anodic Activity of Hydrated and Anhydrous Iron (II) Oxalate in Li-Ion Batteries

We discuss the applicability of the naturally occurring compound Ferrous Oxalate Dihydrate (FOD) (FeC2O4·2H2O) as an anode material in Li-ion batteries. Using first-principles modeling, we evaluate the electrochemical activity of FOD and demonstrate how its structural water content affects the intercalation reaction and contributes to its performance. We show that both Li0 and Li+ intercalation in FOD yields similar results. Our analysis indicates that fully dehydrated ferrous oxalate is a more promising anodic material with higher electrochemical stability: it carries 20% higher theoretical Li storage capacity and a lower voltage (0.68 V at the PBE/cc-pVDZ level), compared to its hydrated (2.29 V) or partially hydrated (1.43 V) counterparts.

Keshavarz, Fatemeh↗
DOE OSTI2023

Electrochemical Doping of Halide Perovskites by Noble Metal Interstitial Cations

Abstract Metal halide perovskites are an attractive class of semiconductors, but it has proven difficult to control their electronic doping by conventional strategies due to screening and compensation by mobile ions or ionic defects. Noble‐metal interstitials represent an under‐studied class of extrinsic defects that plausibly influence many perovskite‐based devices. In this work, doping of metal halide perovskites is studied by electrochemically formed Au + interstitial ions, combining experimental data on devices with a computational analysis of Au + interstitial defects based on density functional theory (DFT). Analysis suggests that Au + cations can be easily formed and migrate through the perovskite bulk via the same sites as iodine interstitials (I i + ). However, whereas I i + compensates n‐type doping by electron capture, the noble‐metal interstitials act as quasi‐stable n‐dopants. Experimentally, voltage‐dependent, dynamic doping by current density–time ( J–t ), electrochemical impedance, and photoluminescence measurements are characterized. These results provide deeper insight into the potential beneficial and detrimental impacts of metal electrode reactions on long‐term performance of perovskite photovoltaic and light‐emitting diodes, as well as offer an alternative doping explanation for the valence switching mechanism of halide‐perovskite‐based neuromorphic and memristive devices.

14 SOLAR ENERGY↗
DOE OSTI2024

Voltage and temperature effects on low cobalt lithium-ion battery cathode degradation

Degradation of low cobalt lithium-ion cathodes was tested using a full factorial combination of upper cut-off voltage (4.0 V and 4.3 V vs. Li/Li + ) and operating temperature (25 °C and 60 °C). Half-cell batteries were analyzed with electrochemical and microstructural characterization methods. Electrochemical performance was assessed with galvanostatic cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) supported by distribution of relaxation times (DRT) analysis. Electrode microstructure was characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray absorption near edge structure (XANES) imaging. Higher cut-off voltage cycling shows presence of NiO x formation, a low diffusivity rock-salt phase, in both CV and XRD data. XRD patterns confirmed that the rock-salt phase was beginning to form at the low cut-off voltage at high temperature, but in much lower intensity than at the high cut-off voltage. Higher temperature accelerates degradation processes at both voltages. Degradation factors at high temperature include NiO x formation, cathode material dissolution, and electrolyte decomposition. SEM analysis suggests that supporting phases may isolate and disconnect active material particles reducing capacity retention and battery life cycle. DRT analysis and XANES imaging show that both high temperature samples revealed a NiO x phase based on an increased diffusive impedance and a visible shift in the XANES spectra. The low cut-off voltage, high temperature sample showed a split peak and shift to lower energies indicating early formation of the NiO x phase. The diffusive impedance, which hinders intercalation and deintercalation, is driven by the formation of the NiO x phase. While primarily driven by cut-off voltage, elevated temperature also contributes to this degradation mechanism.

electrochemical impedance spectroscopy↗
DOE OSTI2022

Direct and Sensitive Electrochemical Evaluation of Pramipexole Using Graphitic Carbon Nitride (gCN) Sensor

Pramipexole (PMXL) belongs to the benzothiazole class of aromatic compounds and is used in treating Parkinson’s disease; however, overdosage leads to some abnormal effects that could trigger severe side effects. Therefore, it demands a sensitive analytical tool for trace level detection. In this work, we successfully developed an electrochemical sensor for the trace level detection of PMXL, using the voltammetric method. For the analysis, graphitic carbon nitride (gCN) was opted and synthesized by using a high-temperature thermal condensation method. The synthesized nanoparticles were employed for surface characterization, using transmission electron microscopy (TEM), X-ray diffraction (XRD), and atomic force microscopy (AFM) techniques. The electrochemical characterization of the material was evaluated by using the electrochemical impedance spectroscopy (EIS) technique to evaluate the solution–electrode interface property. The cyclic voltammetry (CV) behavior of PMXL displayed an anodic peak in the forward scan, indicating that PMXL underwent electrooxidation, and an enhanced detection peak with lower detection potential was achieved for gCN-modified carbon paste electrode (gCN·CPE). The influence of different parameters on the electrochemical behavior was analyzed, revealing the diffusion governing the electrode process with an equal number of hydronium ions and electron involvement. For the fabricated gCN·CPE, good linearity range was noticed from 0.05 to 500 µM, and a lower detection limit (L D ) of 0.012 µM was achieved for the selected concentration range (0.5 to 30 µM). Selectivity of the electrode in PMXL detection was investigated by conducting an interference study, while the tablet sample analysis demonstrates the sensitive and real-time application of the electrode. The good recovery values for the analysis illustrate the efficiency of the electrode for PMXL analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Results from Electrochemical Leach Experiments under the DOE Technical Assistant Program

The activities described in this (report) are related to the analysis and testing of graphite and mine tailing samples provided by the Recipient for the extraction and recovery of embedded metals. This report focused on recovery of platinum group metals (PGMs), which appear in relatively high abundance, particularly technically important elements ruthenium and rhodium. Work performed involved assessment of materials followed by extraction tests using two methods. A novel electrochemically-driven route was compared to a chemical route for extraction of the metals. The electrochemically driven route showed similar results while producing the lixiviant in the electrochemical cell, hence reducing chemical requirements.

42 ENGINEERING↗
DOE OSTI2021

Rapid dissolution of PuO 2 analytical samples using mediated electrochemical oxidation

Current methods for quantitative dissolution of solid PuO 2 involve lengthy dissolution times. The adaptation of mediated electrochemical oxidation, which uses an electrochemically produced oxidizing agent to catalyze dissolution, has been explored for radiochemical analysis scale dissolutions of PuO 2 . The effects of temperature, electrode material, and electrocatalyst on the dissolution kinetics were explored. Under conditions examined in this study, complete dissolution of tens of milligrams of solid PuO 2 can be achieved in less than 1 h at ambient temperature. Overall, this methodology could be adapted to dissolve other metal oxides.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Theoretical Analysis of Critical Conditions for Crack Formation and Propagation, and Optimal Operation of SOECs

A theoretical analysis on crack formation and propagation was performed based on the coupling between the electrochemical process, classical elasticity, and fracture mechanics. The chemical potential of oxygen, thus oxygen partial pressure, at the oxygen electrode-electrolyte interface ( μ O 2 OE∣El ) was investigated as a function of transport properties, electrolyte thickness and operating conditions (e.g., steam concentration, constant current, and constant voltage). Our analysis shows that: a lower ionic area specific resistance (ASR), r i O E , and a higher electronic ASR ( r e O E ) of the oxygen electrode/electrolyte interface are in favor of suppressing crack formation. The μ O 2 O E ∣ E l , thus local pO 2 , are sensitive towards the operating parameters under galvanostatic or potentiostatic electrolysis. Constant current density electrolysis provides better robustness, especially at a high current density with a high steam content. While constant voltage electrolysis leads to greater variations of μ O 2 O E ∣ E l . Constant current electrolysis, however, is not suitable for an unstable oxygen electrode because μ O 2 O E ∣ E l can reach a very high value with a gradually increased r i O E . A crack may only occur under certain conditions when p O 2 T P B > p c r .

42 ENGINEERING↗
DOE OSTI2020

Sequential Electrochemical Flow Cell for Complex Multicomponent Electrocatalysis

A highly efficient flow cell for sequential electrolysis containing two complete electrochemical cells, capable of generating reactive species at the upstream working electrode and transporting them to the downstream working electrode, is demonstrated. Deconvolution of the intermixed electrode circuits is accomplished through analysis of the inherent resistance of the electrolyte, which allows for precise and independent control of the electrochemical potential at each electrode without altering concentrations of supporting or background electrolyte species. Sequential electrolysis involving oxidation of hydrogen and reduction of the generated protons downstream is demonstrated at nearly 100% efficiency on Pt-decorated dealloyed porous Nb catalysts. The conversion efficiency of the catalysts is discussed in terms of their geometries and active surface composition, elucidating strategies for use of sequential electrolysis cells for fundamental and applied studies.

25 ENERGY STORAGE↗
DOE OSTI2020

The origin of passivity in aluminum-manganese solid solutions

In this work, the effects of manganese on the aqueous corrosion of aluminum-manganese alloys were investigated by experiments and atomistic simulations. Electrochemical measurements, x-ray photoelectron spectroscopy, and atom probe tomography analysis indicate that manganese addition enhanced the corrosion resistance of aluminum without participating in the surface oxidation. Furthermore, the selective dissolution of manganese was believed to increase the free volume at the metal/oxide interface to facilitate the formation of a denser, thinner oxide layer with closer to stoichiometry composition. Atomistic simulations showed that the oxide layer compactness increased, and defect density decreased with increasing free volume content in Al, resulting in enhanced barrier characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of Surface Roughness on the Electrochemical Reduction of CO 2 over Cu

We have investigated the role of surface roughening on the CO 2 reduction reaction (CO 2 RR) over Cu. The activity and product selectivity of Cu surfaces roughened by plasma pretreatment in Ar, O 2 , or N 2 were compared with that of electrochemically polished Cu samples. Differences in total and product current densities, the ratio of current densities for HER (the hydrogen evolution reaction) to CO 2 RR, and the ratio of current densities for C 2+ to C 1 products depend on the electrochemically active surface and are nearly independent of plasma composition. Theoretical analysis of an electropolished and roughened Cu surface reveals a higher fraction of undercoordinated Cu sites on the roughened surface, sites that bind CO preferentially. Roughened surfaces also contain square sites similar to those on a Cu(100) surface but with neighboring step sites, which adsorb OC-COH, a precursor to C 2+ products. Here, these findings explain the increases in the formation of oxygenates and hydrocarbons relative to CO and the ratio of oxygenates to hydrocarbons observed with increasing surface roughness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Quantifying Uncertainty in Tortuosity Estimates for Porous Electrodes

Measuring tortuosity in porous electrodes is important for understanding rate capability and optimizing design. Here, we describe an approach to determine electrode tortuosities and quantify the associated uncertainties by fitting a P2D model to discharge profiles from a standard rate capability test. A dimensionless current is identified as a design-of-experiment parameter that can be used to identify experiments that return confident estimates of tortuosity, even when other model parameters are not known with certainty. This approach is applied to analysis of L i x V 3 O 8 (LVO) electrodes and L i x N i 0.33 M n 0.33 C o 0.33 O 2 (NMC) electrodes. The details of the assumptions made in these measurements and their impact on the reported uncertainties are discussed. We also perform an uncertainty analysis on the standard method for quantifying tortuosity in the literature: electrochemical impedance spectroscopy collected under blocking electrolyte conditions. We find that confident estimates can be obtained using this approach even when uncertainties in equivalent circuit model parameters are considered.

25 ENERGY STORAGE↗
DOE OSTI2021

Tutorial: Machine Learning and Artificial Intelligence in Batteries

Machine learning (ML) promises to compress the time needed to characterize battery performance, lifetime and safety. By coupling ML with physical models and metrics, that learning can bridge across materials, chemistries and cell designs. This tutorial will discuss the most popular ML techniques and resources and review recent work in the electrochemical literature. Applications include materials discovery, image recognition for quantitative microscopy analysis, fast charge algorithm development and life prediction.

47 OTHER INSTRUMENTATION↗