Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPLOSIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Light Initiated High Explosive Driven Flyer Plate Impulse Generation Technique For Material and Structural Response

The objective for this research has been to develop a method to induce a high frequency, large amplitude shock pulse into materials and structures as an above-ground laboratory simulation of an exo-atmospheric cold x-ray induced blow-off event. This work builds on the successes of direct-spray Light Initiated High Explosive impulse delivery technique, in order to drive a flyer to a desired impact velocity to induce the proper combined material and structural response of the target. The reported development focuses on flyer velocity from explosive initiation to target impact to flyer rebound. A comprehensive derivation of an analytical model to predict flyer velocity as a function of explosive deposition and flyer properties is presented. One-and two-dimensional test series were conducted to evaluate impulse delivery and impact pressure, as well as target material and structural response. Experimental results show good agreement in flyer velocity between that predicted by the developed theory and that inferred by impulse delivery. A definitive material response was measured in each of the one-dimensional targets. The structural strain response measured in the ring experiments showed excellent agreement with both the predicted flyer performance and the analytical strain solution for a cosine distributed impulsive loading. This work has focused on the utilization of analytical, hydrocode, and test analysis to confirm that a LIHE driven flyer impulse technique can be an effective simulation of a cold x-ray blow-off event. It is shown that a thin metallic flyer plate can be explosively accelerated to impact a target with sufficient energy to generate an impulsive load which induces both structural and material response in a test item.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Low-frequency Electromagnetic Detection Limits of Underground Nuclear Explosions

Underground nuclear explosions produce a broadband electromagnetic signal that can propagate to the surface at some distance. We perform a logistic regression on historical electromagnetic detections to calculate a probabilistic detection curve for prediction of the propagation distance for any given underground nuclear explosion. The curve predicts positive detections at scaled ranges of 2414.6, 2025.7, 1908.3, and 1672.4 m/ktonne 1/3 at probabilities of 50, 90, 95 and 99%, respectively. For a theoretical 100 ktonne underground nuclear explosion these scaled ranges translate to absolute ranges of 11.2, 9.4, 8.9, and 7.8 km at probabilities of 50, 90, 95 and 99%, respectively. We also motivate a need for improved electromagnetic sensor design and deployment by extending the detection analysis using the quoted signal-to-noise ratio of two and noise amplitude of 10 pT along with attenuation relationships that go as 1/r to 1/r 3 . We find that reducing the noise floor by a factor often could extend the detection limit to approximately 5 to 25 km/ktonne 1/3 , which translates to 24 to 112 km for a theoretical 100 ktonne underground nuclear explosion.

58 GEOSCIENCES↗
DOE OSTI2017

EDS V26 Vessel Clamp Explosive Test Report

This report documents the results of explosive re-qualification tests of the EDS V26 Vessel that were conducted at Sandia National Laboratories in Albuquerque, New Mexico in May 2015 following the retrofitting of the vessel with a three piece clamp for use on the P2A system. The V26 containment vessel is the second EDS vessel to be fabricated under Code Case 2564 of the ASME Boiler and Pressure Vessel Code, which provides rules for the design of impulsively loaded vessels. The explosive rating for the vessel, based on the code case, is nine (9) pounds TNT-equivalent for up to 637 detonations. The goals of the tests were to qualify the vessel, particularly the clamping system, for explosive use. The explosive tests consisted of a 9 pound bare charge of Composition C-4 (equivalent to 11.25 pounds TNT), followed by a 7.2 pound bare charge of Composition C-4 (equivalent to 9 pounds of TNT). Helium permeation measurements of the seal and strain measurements using a pi tape and strain gauges were made. All vessel acceptance criteria were met.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Standardizing an Intermediate-Scale High Explosive Safety Test Suite

Small-scale safety testing, while successful in screening out extremely dangerous explosive compositions, does not fully characterize the explosive hazards associated with handling larger, consolidated or bare charges. It is proposed that intermediate-scale tests using consolidated charges in the range 25 mg – 1 kg are warranted to satisfactorily address the hazards. A standard for this intermediate-scale testing should be developed, proofed, peer-reviewed and adopted to assist in the development of safe new high explosive compositions across the complex. This whitepaper explains why current small-scale safety testing is insufficient to characterize the handling hazard, identifies the guiding aspects of explosive response that drive the handling hazards associated with larger consolidated charges, and proposes a suite of tests/experiments that can serve as a starting point for an intermediate-scale safety standard.

42 ENGINEERING↗
DOE OSTI2024

A multi-Physics Experiment for Low-Yield Nuclear Explosion Monitoring

A series of multi-physics experiments, referred to as Physics Experiment 1 (PE1) is underway at the United States’ Nevada National Security Site (NNSS). The PE1 series includes detonations of three underground chemical explosions in P-tunnel, with fully coupled (PE1 A), partially decoupled (PE1 D L ), and fully decoupled (PE1 B) emplacements. Canisters with gas tracers are imbedded in the explosives, and the tracers are released when the canister is destroyed by the detonation. A dedicated electromagnetic (EM) experiment (EMX) generates well-characterized EM signals at an underground location near the chemical explosive experiments. A series of atmospheric experiments (METEX, REACT, and METREX) release smoke and radioactive tracers around Aqueduct Mesa to test gas transport in complex topography. Each of the chemical explosive experiments includes a network of sensors to record seismic, acoustic, and electromagnetic waves, measurement of atmospheric conditions, and air sample collection for measurement of tracer concentration. EMX records EM signals underground and on the surface of Aqueduct Mesa. METEX, REACT, and METREX include measurement of atmospheric condition, as well as tracking smoke releases. REACT and METREX add low-level radioactive gas tracers to the atmospheric releases.

58 GEOSCIENCES↗
DOE OSTI2024

Temperature and Pressure Instrumentation for LYNM PE1 Chemical Explosive Testing

Underground chemical explosive testing has been conducted at the Nevada National Security Site under the Physics Experiment 1 (PE1) to validate explosive computer modeling and, ultimately, improve the accuracy of subsurface explosive detection. This SAND Report describes the dynamic temperature and pressure measurements within the chamber induced by the chemical explosive for the first of three experiments, PE1-A. The report details the instrumentation used for the experiment, the emplacement of the hardware, and the measured results. Dynamic temperature measurements were accomplished with the use of optical spectrometers and dynamic pressure was measured with a series of high-rated pressure transducers. This report includes details of the design and results of four cavity sensor systems used to measure early-time temperature, early-time pressure, late-time temperature, and late time pressure. The outcomes of PE1-A were used to inform the design of the remaining PE1 series experiments, PE1-B and PE1-DL.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2016

Type Ia Supernova Explosions From Hybrid Carbon–Oxygen–Neon White Dwarf Progenitors

Motivated by recent results in stellar evolution that predict the existence of hybrid white dwarf (WD) stars with a C–O core inside an O–Ne shell, we simulate thermonuclear (Type Ia) supernovae from these hybrid progenitors. We use the FLASH code to perform multidimensional simulations in the deflagration-to-detonation transition (DDT) explosion paradigm. Our hybrid progenitor models were produced with the MESA stellar evolution code and include the effects of the Urca process, and we map the progenitor model to the FLASH grid. We performed a suite of DDT simulations over a range of ignition conditions consistent with the progenitor's thermal and convective structure assuming multiple ignition points. To compare the results from these hybrid WD stars to previous results from C–O WDs, we construct a set of C–O WD models with similar properties and similarly simulate a suite of explosions. We find that despite significant variability within each suite, trends distinguishing the explosions are apparent in their ${}^{56}\mathrm{Ni}$ yields and the kinetic properties of the ejecta. We compare our results with other recent work that studies explosions from these hybrid progenitors.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Dependence of Dust Formation on the Supernova Explosion

We investigate the properties, composition, and dynamics of dust formation and growth for a diverse set of core-collapse supernovae (CCSNe), with 15, 20, and 25 M ⊙ progenitor masses, explosion energies ranging from 0.5 to 120 foe, and varied engine type. These explosions are evolved with a 1D Lagrangian hydrodynamics code out to a minimum of 1157 days to model the ejecta as it expands and cools. A multigrain dust nucleation and growth model is applied to these results. We find that higher explosion energies lead to an earlier onset of dust formation, smaller grain sizes, and larger silicate abundances. Further, we see that nuclear burning during the explosion leads to enhanced formation of silicate dust. Finally, we build composite models from our suite to predict the efficiency of CCSN dust production as a function of metallicity.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Black Hole Formation Accompanied by the Supernova Explosion of a 40 M ⊙ Progenitor Star

Abstract We have simulated the collapse and evolution of the core of a solar-metallicity 40 M ⊙ star and find that it explodes vigorously by the neutrino mechanism, despite its very high “compactness.” Within ∼1.5 s of explosion, a black hole forms. The explosion is very asymmetrical and has a total explosion energy of ∼1.6 × 10 51 erg. At black hole formation, its baryon mass is ∼2.434 M ⊙ and gravitational mass is 2.286 M ⊙ . Seven seconds after black hole formation, an additional ∼0.2 M ⊙ is accreted, leaving a black hole baryon mass of ∼2.63 M ⊙ . A disk forms around the proto−neutron star, from which a pair of neutrino-driven jets emanates. These jets accelerate some of the matter up to speeds of ∼45,000 km s −1 and contain matter with entropies of ∼50. The large spatial asymmetry in the explosion results in a residual black hole recoil speed of ∼1000 km s −1 . This novel black hole formation channel now joins the other black hole formation channel between ∼12 and ∼15 M ⊙ discovered previously and implies that the black hole/neutron star birth ratio for solar-metallicity stars could be ∼20%. However, one channel leaves black holes in perhaps the ∼5–15 M ⊙ range with low kick speeds, while the other leaves black holes in perhaps the ∼2.5–3.0 M ⊙ mass range with high kick speeds. However, even ∼8.8 s after core bounce the newly formed black hole is still accreting at a rate of ∼2 × 10 −2 M ⊙ s −1 , and whether the black hole eventually achieves a significantly larger mass over time is yet to be determined.

Astronomy & Astrophysics↗
DOE OSTI2025

Physics-driven Explosions of Stripped High-mass Stars: Synthetic Light Curves and Spectra of Stripped-envelope Supernovae with Broad Light Curves

Stripped-envelope supernovae (SESNe) represent a significant fraction of core-collapse supernovae, arising from massive stars that have shed their hydrogen and, in some cases, helium envelopes. The origins and explosion mechanisms of SESNe remain a topic of active investigation. In this work, we employ radiative-transfer simulations to model the light curves and spectra of a set of explosions of single, solar-metallicity, massive Wolf–Rayet stars with ejecta masses ranging from 4 to 11 M ⊙ , which were computed from a turbulence-aided and neutrino-driven explosion mechanism. We analyze these synthetic observables to explore the impact of varying ejecta mass and helium content on observable features. We find that the light curve shape of these progenitors with high ejecta masses is consistent with observed SESNe with broad light curves but not the peak luminosities. The commonly used analytic formula based on rising bolometric light curves overestimates the ejecta mass of these high-initial-mass progenitor explosions by a factor of up to 2.6. In contrast, the calibrated method by Haynie et al., which relies on late-time decay tails, reduces uncertainties to an average of 20% within the calibrated ejecta mass range. Spectroscopically, the He I 1.083 μm line remains prominent even in models with as little as 0.02 M ⊙ of helium. However, the strength of the optical He I lines is not directly proportional to the helium mass but instead depends on a complex interplay of factors such as the 56 Ni distribution, composition, and radiation field. Thus, producing realistic helium features requires detailed radiative transfer simulations for each new hydrodynamic model.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Presupernova O–C Shell Mergers Could Produce More 44 Ti than the Explosion

The formation of 44 Ti in massive stars is thought to occur during explosive nucleosynthesis; however, recent studies have shown it can be produced during O–C shell mergers prior to core collapse. We investigate how mixing according to 3D macrophysics derived from hydrodynamic simulations impacts presupernova O–C shell merger nucleosynthesis and if it can dominate explosive supernova production of 44 Ti and other radioactive isotopes. We compare a range of observations and models of explosive 44 Ti yields to preexplosive multizone mixing–burning nucleosynthesis simulations of an O–C shell merger in a 15 M ⊙ Z = 0.02 stellar model with mixing conditions corresponding to different 3D hydrodynamic mixing scenarios. Radioactive species produced in the O shell have a multidex spread in preexplosive yield predictions across different 3D mixing scenarios of 1.54 and 2.14 dex on average, depending on mass cut. 44 Ti has the largest spread of 4.78 and 4.81 dex depending on mass cut. Further, we show that the preexplosive production of 44 Ti can be larger than the explosive production of models and can match observations. Our results also show that 3D mixing physics enhances 44 Ti in 1D models without modifying 56 Ni yields. We conclude that quantitative predictions of 44 Ti and other radioactive species more broadly require an understanding of the 3D hydrodynamic mixing conditions present during the O–C shell merger.

Issa, Joshua [University of Victoria, BC (Canada);↗
NASA NTRS1973

Explosives for Lunar Seismic Profiling Experiment (LSPE)

Explosive charges of various sizes were investigated for use in lunar seismic studies. Program logistics, and the specifications for procurement of bulk explosives are described. The differential analysis, thermal properties, and detonation velocity measurements on HNS/Teflon 7C 90/10 are reported along with the field tests of the hardware. It is concluded that nearly all large explosive charges crack after fabrication, from aging or thermal shock. The cracks do not affect the safety, or reliability of the explosives.

Source record↗
NASA NTRS1973

Introduction to gasdynamics of explosions

Questions concerning the genesis and sustenance of an explosion are investigated, giving attention to the mechanics of explosions, the gasdynamics of explosions, aspects of technological significance, and future prospects. The dynamics of exothermic processes is discussed together with the most prominent effects of explosions. Blast waves are considered, taking into account conservation principles, blast wave transformation, conservative equations in nondimensional form, the equation of state, Eulerian space profiles, Eulerian time profiles, Lagrangian time profiles, boundary conditions and integral relations, and self-similar flow fields.

Oppenheim, A. K.↗
NASA NTRS1975

Application of blast wave theory to explosive propulsion

An analysis was carried out by using blast wave theory to delineate the important aspects of detonating explosives in nozzles, such as flow and wave phenomena, characteristic length and time scales, and the parameters on which the specific impulse is dependent. The propulsive system utilizes the momentum of the ambient gas set into motion in the nozzle by the explosion. A somewhat simplified model was considered for the situation where the mass of ambient gas in the nozzle is much greater than the mass of gas produced in the explosion, a condition of interest for dense atmospheres, e.g., near the surface of Venus. Instantaneous detonation and energy release was presumed to occur at the apex of a conical nozzle, and the shock wave generated by the explosion was taken to propagate as a spherical wave, thereby setting the ambient gas in the nozzle into one-dimensional radially outward motion.

Back, L. H.↗
NASA NTRS1977

Application of high explosion cratering data to planetary problems

The present paper deals with the conditions of explosion or nuclear cratering required to simulate impact crater formation. Some planetary problems associated with three different aspects of crater formation are discussed, and solutions based on high-explosion data are proposed. Structures of impact craters and some selected explosion craters formed in layered media are examined and are related to the structure of lunar basins. The mode of ejection of material from impact craters is identified using explosion analogs. The ejection mode is shown to have important implications for the origin of material in crater and basin deposits. Equally important are the populations of secondary craters on lunar and planetary surfaces.

Oberbeck, V. R.↗
NASA NTRS1982

Explosively Actuated Opening for Rapid Egress

Flexible linear-shaped charge provides explosive energy to create opening and to jettison panel. Container around explosive charge protects pilot from effects of explosion. Exterior steel strip receives most of force of explosion to jettison severed panel. System allows pilot to bail out from left side of airplane by creating opening where no door exists. Egress system is simple and highly responsive, requiring minimal modifications to airplane.

Bement, L. J.↗
NASA NTRS1982

Holographic studies of the vapor explosion of vaporizing water-in-fuel emulsion droplets

Holographic studies were performed which examined the fragmentation process during vapor explosion of a water-in-fuel (hexadecane/water) emulsion droplet. Holograms were taken at 700 to 1000 microseconds after the vapor explosion. Photographs of the reconstructed holograms reveal a wide range of fragment droplet sizes created during the explosion process. Fragment droplet diameters range from below 10 microns to over 100 microns. It is estimated that between ten thousand and a million fragment droplets can result from this extremely violent vapor explosion process. This enhanced atomization is thus expected to have a pronounced effect on vaporization processes which are present during combustion of emulsified fuels.

Sheffield, S. A.↗
NASA NTRS1984

Experiments on water/melt explosions, nature of products, and models of dispersal

Experiments were carried out in a steel pressure device using controlled amounts of water and thermite melt to examine the mechanical energy released on explosive mixing following the initial contact of the two materials. An experimental design was used to allow the direct calculation of the mechanical energy by the dynamic lift of the device as recorded both optically and physically. A large number of experiments were run to accurately determine the optimum mixture of water and melt for the conversion of thermal to mechanical energy. The maximum efficiency observed was about 12% at a water/thermite mass ratio of 0.50. These experiments are the basis for the development of models of hydroexplosions and melt fragmentation. Particles collected from the experimental products are similar in size and shape to pyroclasts produced by much larger hydrovolcanic explosions. Melt rupture at optimum ratios produces very fine particles whereas rupture at high or low water/melt ratios produces large melt fragments. Grain surface textures in the experimental products are also related to the water/melt ratio and the mechanism of explosive mixing. It is thus possible to have qualitative information about the nature of the explosion from the sizes and shapes of the fragments produced.

Sheridan, M. F.↗