Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTIC ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

The Beneficial Effect of Iron in Aluminum-Cerium-Based Cast Alloys

Iron (Fe) has been considered a major impurity since it is detrimental to the mechanical properties of many cast aluminum alloys due to the formation of Fe-containing brittle intermetallic phases. Fe is found naturally as an impurity in bauxite ore, resulting in Fe contamination of aluminum alloys with increasing contamination from current recycling practices. The Al–Ce–Fe system was investigated using CALPHAD (CALculation of PHAse Diagrams) modeling and experimental casting techniques. It was found that additions of Fe to the Al–Ce system are beneficial to the strength (slightly) and ductility (significantly) of the ternary alloys, which is attributed to the formation of fine metastable Al 8 CeFe 2 phase with aggregate morphology and equilibrium Al 10 CeFe 2 phase, suppressing coarse proeutectic Al 11 Ce 3 phase in near-eutectic Al–Ce alloys. Heat treatment study showed that the metastable Al 8 CeFe 2 phase transforms to predicted equilibrium Al 10 CeFe 2 phase at 500 °C, with essentially no intermetallic or grain coarsening; thus, the alloy displayed excellent property retention. The Al–Ce–Fe alloy system offers opportunities for sustainable, recyclable alloy development using low-cost Fe and low-cost cerium (a byproduct of rare-earth extraction).

42 ENGINEERING↗

Thermal Analysis of Cerium-Treated Chill-Cast Al-23 Si Alloy

The influence of elemental cerium addition on the cooling curve parameters and microstructure of hypereutectic Al-23Si alloy was investigated in this work. The cooling rate of the treated and untreated alloy samples was varied by solidifying the melt against chills of different materials in a stainless-steel tube. The cooling curve was recorded and nucleation temperatures of various phases in the alloy were measured. The results show that the chilling improves the effectiveness of the modifier. The two main phases of the alloy, primary silicon and eutectic silicon, were nucleated at temperatures of about 661.2 and 571.6 °C, respectively. The addition of Ce to slowly cooled alloys resulted in an increase in undercooling temperature of both the phases, with a decrease in its nucleation temperature, whereas the same additions increased the nucleation temperatures in chilled alloys. Based on the thermal analysis results, a relation between thermal analysis parameter (ΔT{sub G}) and silicon particle size of the alloy was proposed.

36 MATERIALS SCIENCE↗

The influence of growth speed, orientation and environment on fracture of aligned Al-CuAl2

There has been considerable interest in the mechanical properties of aligned eutectics as functions of microstructure, orientation between reinforcement and stress axis, and temperature of testing. However, little is known about the behavior of these alloys in aggressive environments, such as liquid metals, with the exception of a recent paper on embrittlement of several eutectic alloys in gallium and gallium-indium alloys. This paper is concerned with the effects of a liquid Ga-16%In solution on tensile behavior of an aligned Al-CuAl2 eutectic.

Skiff, P. K.↗

The use of a directional solidification technique to investigate the interrelationship of thermal parameters, microstructure and microhardness of Bi–Ag solder alloys

Bi–Ag alloys have been stressed as possible alternatives to replace Pb-based solder alloys. Although acceptable melting temperatures and suitable mechanical properties may characterize such alloys, as referenced in literature, there is a lack of comprehension regarding their microstructures (morphologies and sizes of the phases) considering a composition range from 1.5 to 4.0 wt.%Ag. In order to better comprehend such aspects and their correlations with solidification thermal parameters (growth rate, v and cooling rate, T-dot), directional solidification experiments were carried out under transient heat flow conditions. The effects of Ag content on both cooling rate and growth rate during solidification are examined. Microstructure parameters such as eutectic/dendritic spacing, interphase spacing and diameter of the Ag-rich phase were determined by optical microscopy and scanning electron microscopy. The competition between eutectic cells and dendrites in the range from 1.5 to 4.0 wt.%Ag is explained by the coupled zone concept. Microhardness was determined for different microstructures and alloy Ag contents with a view to permitting correlations with microstructure parameters to be established. Hardness is shown to be directly affected by both solute macrosegregation and morphologies of the phases forming the Bi–Ag alloys, with higher hardness being associated with the cellular morphology of the Bi-2.5 and 4.0 wt.%Ag alloys. - Highlights: • Asymmetric zone of coupled growth for Bi–Ag is demonstrated. • Faceted Bi-rich dendrites have been characterized for Bi–1.5 wt.%Ag alloy. • Eutectic cells were shown for the Bi-2.5 and 4.0 wt.%Ag solder alloys. • Interphase spacing relations with G × v are able to represent the experimental scatters. • Hall-Petch type equations are proposed relating microstructural spacings to hardness.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of hypoeutectic Al–6Ce–3Ni-0.7Fe (wt.%) alloy

Here, a hypoeutectic, Fe-modified Al–Ce–Ni alloy (Al–6Ce–3Ni-0.7Fe, wt.%) is studied in terms of microstructure, thermal stability, ambient temperature strengthening, and creep resistance. The as-cast microstructure consists of primary Al dendrites and interdendritic binary eutectic regions (Al–Al11Ce3 and/or Al–Al9(Fe,Ni)2), with micron/submicron lamellar spacing, depending on the location along the height of the ingot. The cast alloy exhibits excellent coarsening resistance at 400 °C, with mostly unchanged microstructure and microhardness after 6 weeks of aging, indicating good thermal stability of Al11Ce3 and Al9(Fe,Ni)2. Orowan strengthening and load transfer are identified as strengthening mechanisms at ambient and elevated temperature. A high volume fraction of the intermetallic phases (providing load transfer) and relatively coarse eutectic spacing (for modest Orowan strengthening) result in a moderate as-cast microhardness of 566 ± 32 MPa. Creep resistance at 300 and 350 °C is similar to a binary Al-12.5Ce eutectic alloy (with twice the Ce content) because of two countering effects: Al–6Ce–3Ni-0.7Fe shows a higher volume fraction of strengthening intermetallic phases, but it also exhibits a large fraction of primary Al dendrites which weaken the alloy. By contrast, the alloy, when laser-remelted at the surface, has a fully eutectic microstructure without primary aluminum dendrites achieved by high undercooling on solidification, with a refined network of eutectic phases that doubles the microhardness as compared to the cast alloy. Whereas coarsening is faster due to the shorter diffusion distances between the eutectic phases, hardness remains ~30% higher than the as-cast alloy after ~6 weeks aging at 400 °C.

36 MATERIALS SCIENCE↗

Fundamental Studies of Solidification in Microgravity Using Real-Time X-Ray Microscopy

This research applies a state of the art X-ray Transmission Microscope, XTM, to image (with resolutions up to 3 micrometers) the solidification of metallic or semiconductor alloys in real-time. We have successfully imaged in real-time: interfacial morphologies, phase growth, coalescence, incorporation of phases into the growing interface, and the solute boundary layer in the liquid at the solid-liquid interface. We have also measured true local growth rates and can evaluate segregation structures in the solid; a form of in-situ metallography. During this study, the growth of secondary phase fibers and lamellae from eutectic and monotectic alloys have been imaged during solidification, in real-time, for the first time in bulk metal alloys. Current high resolution X-ray sources and high contrast X-ray detectors have advanced to allow systematic study of solidification dynamics and the resulting microstructure. We have employed a state-of-the-art sub-micron source with acceleration voltages of 10-100 kV to image solidification of metals. One useful strength of the XTM stems from the manner an image is formed. The radiographic image is a shadow formed by x-ray photons that are not absorbed as they pass through the specimen. Composition gradients within the specimen cause variations in absorption of the flux such that the final image represents a spatial integral of composition (or thickness). The ability to image these features in real-time enables more fundamental and detailed understanding of solidification dynamics than has previously been possible. Hence, application of this technique towards microgravity experiments will allow rigorous testing of critical solidification models.

Curreri, Peter A.↗

Crystalline monolayer surface of liquid Au-Cu-Si-Ag-Pd: Metallic glass former

It is demonstrated by means of x-ray synchrotron reflectivity and diffraction that the surface of the liquid phase of the bulk metallic glass forming alloy Au 49 Cu 26.9 Si 16.3 Ag 5.5 Pd 2.3 consists of a two-dimensional crystalline monolayer phase for temperatures of up to about 50 K above the eutectic temperature. The present alloy as well as glass forming Au 82 Si 18 and Au-Si-Ge alloys containing small amounts of Ge are the only metallic liquids to exhibit surface freezing well above the melting temperature. This suggests that the phenomena of surface freezing in metallic liquids and glass forming ability are related and probably governed by similar physical properties.

36 MATERIALS SCIENCE↗

In-Situ X-Ray Microscopy of Phase and Composition Distributions in Metal Alloys During Solidification

This research applies a state of the art X-ray Transmission Microscope, to image the solidification of metallic or semiconductor alloys in real-time. By employing a hard x-ray source with sub-micron dimensions, resolutions of up to 3 gm can be obtained with magnifications of over 800 X. Specimen growth conditions were optimized and the best imaging technologies applied to maintain x-ray image resolution, contrast and sensitivity. In addition, a special furnace design is required to permit controlled growth conditions and still offer maximum resolution and image contrast. We have successfully imaged in real-time: interfacial morphologies, phase growth, coalescence, incorporation of phases into the growing interface, and the solute boundary layer in the liquid at the solid-liquid inter-face. We have also measured true local growth rates and can evaluate segregation structures in the solid; a form of in-situ metallography. Composition gradients within the specimen cause vafiations in absorption of the flux such that the final image represents a spatial integral of composition (or thickness). During this study, the growth of secondary phase fibers and lameilae from eutectic and monotectic alloys have been imaged during solidification, in real-time, for the first time in bulk metal alloys. Keywords: x-ray, microscope, solidification, microfocus, real-time, microstructure

Kaukler, William F.↗

Role of Titanium, Carbon, Boron, and Zirconium in Carbide and Porosity Formation during Equiaxed Solidification of Nickel-Based Superalloys

This work analyses the effect of Ti in the MC carbide formation and also in the γ/γ´ eutectic promotion in two nickel-based alloys melted under vacuum conditions and solidified into ceramic molds. The role of boron, carbon and zirconium on the porosity level after solidification of both alloys was also investigated; since the alloys were vacuum melted, it is assumed that the observed porosity is due to micro-shrinkage. The chemical compositions for two alloys were: 20.2Cr-13.7Co-4.78Mo-1.19Al-0.69Ti-0.08C-2.34Fe for Alloy 1, and 20.5Cr-15.6Co5.03Mo-1.57Al-3.42Ti-0.15C-1.64Fe-0.076Zr-0.01%B for Alloy 2. Results showed a higher volume fraction of MC carbides and the γ/γ´ eutectic for the Alloy 2 with higher titanium content since this element is a carbide and γ/γ´ eutectic promoter. The porosity level in the Alloy 2, with higher amounts of carbon, boron and zirconium was considerably lower than that for the Alloy 1. These results are discussed in terms of different phenomena caused by the segregating effects of boron, carbon and zirconium towards the interdendritic regions and the formation of zirconium carbides that produce an expansion in volume when they are formed at the end of the solidification process.

36 MATERIALS SCIENCE↗

Review of Emerging Potassium–Sulfur Batteries

Abstract This is the first review on potassium–sulfur (K–S) batteries (KSBs), which are emerging metal battery (MB) systems. Since KSBs are quite new, there are fundamental questions regarding the electrochemistry of S‐based cathode and of K metal anode, as well as the holistic aspects of full‐cell performance. The manuscript begins with a critical discussion regarding the potassium–sulfur electrochemistry and on how it differs from the much better‐known lithium–sulfur. Cathodes are discussed next, focusing on the role of sulfur structure, carbon host chemistry and porosity, and electrolytes in establishing the reversible potassium sulfide K 2 S n phase sequence, the parasitic polysulfide shuttle, pulverization‐driven capacity fade, etc. Following is a discussion of solid‐state electrolytes (SSEs), including of hybrid solid–liquid systems that show much promise. Potassium metal anodes are then critically reviewed, emphasizing electrolyte reactions to form stable versus unstable solid electrolyte interphase (SEI), covering the current understanding of potassium dendrites, and highlighting the deep‐eutectic K–Na alloying approaches for room temperature liquid anodes. The manuscript concludes with K–S batteries, focusing on cell architectures and providing quantitative performance comparisons as master plots. Unanswered scientific/technological questions are identified, emerging research opportunities are discussed, and potential experimental and simulation‐based studies that can unravel these unknowns are proposed.

Ding, Jia↗

Galinstan liquid metal breakup and droplet formation in a shock-induced cross-flow

Liquid metal breakup processes are important for understanding a variety of physical phenomena including metal powder formation, thermal spray coatings, fragmentation in explosive detonations and metalized propellant combustion. Since the breakup behaviors of liquid metals are not well studied, we experimentally investigate the roles of higher density and fast elastic surface oxide formation on breakup morphology and droplet characteristics. This work compares the column breakup of water with Galinstan, a room-temperature eutectic liquid metal alloy of gallium, indium and tin. A shock tube is used to generate a step change in convective velocity and back-lit imaging is used to classify morphologies for Weber numbers up to 250. Digital in-line holography (DIH) is then used to quantitatively capture droplet size, velocity and three-dimensional position information. Differences in geometry between canonical spherical drops and the liquid columns utilized in this paper are likely responsible for observations of earlier transition Weber numbers and uni-modal droplet volume distributions. Scaling laws indicate that Galinstan and water share similar droplet size-velocity trends and root-normal volume probability distributions. Furthermore, measurements indicate that Galinstan breakup occurs earlier in non-dimensional time and produces more non-spherical droplets due to fast oxide formation.

36 MATERIALS SCIENCE↗

Amino Acid Sequence Controls Enhanced Electron Transport in Heme-Binding Peptide Monolayers

Metal-binding proteins have the exceptional ability to facilitate long-range electron transport in nature. Despite recent progress, the sequence-structure–function relationships governing electron transport in heme-binding peptides and protein assemblies are not yet fully understood. In this work, the electronic properties of a series of heme-binding peptides inspired by cytochrome bc1 are studied using a combination of molecular electronics experiments, molecular modeling, and simulation. Self-assembled monolayers (SAMs) are prepared using sequence-defined heme-binding peptides capable of forming helical secondary structures. Following monolayer formation, the structural properties and chemical composition of assembled peptides are determined using atomic force microscopy and X-ray photoelectron spectroscopy, and the electronic properties (current density–voltage response) are characterized using a soft contact liquid metal electrode method based on eutectic gallium–indium alloys (EGaIn). Our results show a substantial 1000-fold increase in current density across SAM junctions upon addition of heme compared to identical peptide sequences in the absence of heme, while maintaining a constant junction thickness. These findings show that amino acid composition and sequence directly control enhancements in electron transport in heme-binding peptides. Overall, this study demonstrates the potential of using sequence-defined synthetic peptides inspired by nature as functional bioelectronic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomic-scale combination of germanium-zinc nanofibers for structural and electrochemical evolution

Alloy materials have been emerged to achieve compatible properties in various applications. The structural manipulation, however, requires sensitive and complicated synthetic process. Herein, we report atomic-scale combination of germanium-zinc distorted alloy exhibiting uncertain eutectic point in a phase diagram can imply a great potential to form atomically collaborated array via a simple fabrication method. When interconnected together, it prevents a fatal sublimation of germanium/germanium oxide during gas-solid phase reduction reaction and allows outstanding electronic conductivity as well as high available capacity in lithium-ion batteries, leading to structural and electrochemical evolution of germanium/zinc distorted array. Further, the unique features are clearly confirmed through in situ analysis. Besides, as-prepared battery anodes remarkably highlights outstanding rate capabilities (capacity retention of ~50% at 20 C compared to 0.2 C-rate) and cycle retention (73% at 3.0 C-rate) with a capacity of 546 mAh g -1 even after 1000 cycles. Even when assembled in a full cell, it notably facilitates considerable energy density during 400 cycles with 99.4% of average coulombic efficiency, which is suitable for a large-scale energy storage system.

36 MATERIALS SCIENCE↗

Application of Liquid Metals in Nano Particles and Vitrimers (Summer Quarter Report)

The melting points of pure elemental metals can be decreased by forming liquid metal alloys at the eutectic point composition. Utilizing this unique characteristic, the desirable properties of electron rich metals can be incorporated into new materials and applications. Liquid metals can be made into nanoparticles (LMNP), allowing for increased surface areas of a highly tunable and functional metal oxide skins. Careful characterization is important for understanding LMNP with many methods available to not only investigate size and distribution, but also surface chemistries. This is a review article written to fulfill the UO KCGIP Masters Program requirements.

36 MATERIALS SCIENCE↗

New materials in the aerospace industries

Trends in the development of new aerospace metals and alloys are reviewed, and applications of these advanced materials in nonaerospace fields are indicated. Emphasis is placed on the light metals and the high-temperature alloys. Attention is given to the properties and uses of the high-strength aluminum alloy 7050, alpha and beta titanium alloys, dispersion strengthened superalloys, metal-metal composites, eutectic superalloys, and coated columbium alloys.

Gangler, J. J.↗

Effect of undercooling on the microstructure of Ni-35 at. pct Mo (eutectic) and Ni-38 at. pct Mo (hypereutectic) alloys

Ni-35 at. pct Mo and Ni-38 at. pct Mo alloy specimens have been solidified from various levels of undercooling in the differential thermal analysis and the electromagnetic levitation units in a pyrex/vycor bed. The evolution of the microstructure in the solified specimens has been examined in terms of the degree of undercooling, the nature of the first phase to nucleate from the melt, and the specimen cooling rate. The melt has been observed to undercool more in the presence of intermetallic NiMo (beta) phase as compared to that in the presence of nickel-rich solid solution (gamma). The 'anomalous eutectic' type of microstructure has been shown to result from the initial formation of the dendritic skeleton of either of the two phases, its segmentation due to convection and ripening, and the subsequent nucleation of the other phase in the interdendritic liquid regions. The recalescence behavior has been examined as a function of undercooling and the nature of the phase nucleating first in the melt.

Tewari, S. N.↗

Three-dimensional morphology of an ultrafine Al-Si eutectic produced via laser rapid solidification

Al-Si alloys processed by laser rapid solidification yield eutectic microstructures with ultrafine and interconnected fibers. Such fibrous structures have long been thought to bear resemblance to those formed in impurity-doped alloys upon conventional casting. Here, we show that any similarity is purely superficial. By harnessing high-throughput characterization and computer vision techniques, we perform a three-dimensional analysis of the branching behavior of the ultrafine eutectic and compare it against an impurity-modified eutectic as well as a random fractal (as a benchmark). Differences in the branching statistics point to different microstructural origins of the impurity- and quench-modified eutectic. Finally, our quantitative approach is not limited to the data presented here but can be used to extract abstract information from other volumetric datasets, without customization.

36 MATERIALS SCIENCE↗

Effects of high magnetic field on the evolutions of constituent phases in 7085 aluminum alloy during homogenization

The evolutions of coarse constituent phases in homogenized 7085 aluminum alloy at different conditions with or without the application of 12 T high magnetic field were examined by using differential scanning calorimetry, scanning electronic microscope, energy dispersive spectroscopy and X-ray diffraction. It is found that the main constituent phases including quaternary phase T(AlZnMgCu), Al{sub 7}Cu{sub 2}Fe, and AlTiCuFeSi are present in as-cast 7085 alloy. During homogenization, {alpha} + T eutectics become discontinuous and spheroidized, and Al{sub 2}CuMg phase nucleates and grows along {alpha} + T eutectics. High magnetic field significantly accelerates the melting of quaternary phase T and Al{sub 2}CuMg phase. When the alloy homogenized at 460 Degree-Sign C/10 h + 480 Degree-Sign C/8 h with 12 T magnetic field, the least amount of constituent phases is obtained. - Highlights: Black-Right-Pointing-Pointer Most of published reports of magnetic field are focused on ferrous alloys. Black-Right-Pointing-Pointer Effect of magnetic field on microstructure of 7085 during homogenization is studied. Black-Right-Pointing-Pointer Magnetic field accelerates the melting of AlZnMgCu and S phase.

36 MATERIALS SCIENCE↗