Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Determination of Elastic Properties and Characterization of Thermal Barrier Coatings using Resonant Ultrasound Spectroscopy

Mechanical properties of plasma sprayed ceramic coatings are extremely important to engine design. However, the determination of these properties is often difficult because of the unique and complicated microstructure of the coatings. In this presentation the determination of the elastic constants of plasma sprayed Yttria stabilized Zirconia thermal barrier coatings using resonant ultrasound spectroscopy will be described along with an analysis that enables the determination of the elastic constants as a function of temperature and coating direction. In this work, results on the following issues will be discussed: 1) the elastic anisotropy of thermal barrier coatings, which is associated with coating failure modes; 2) sintering effects on coating compliance comparing with thermal behavior, which is important to coating performance on engineering structures, such as turbine engines; 3) coating elastic modulus at high temperatures close to the service condition, which provides insights of coating mechanical behavior in both fundamental and practical studies.

36 MATERIALS SCIENCE↗

Mechanical Deformation of a Lithium-Metal Anode Due to a Very Stiff Separator

This work builds on the two-dimensional model presented by Ferrese et al. [J. Electrochem. Soc., 159, A1615 (2012)1, which captures the movement of lithium metal at the negative electrode during cycling in a Li-metal/LiCoO2 cell. In this paper, the separator is modeled as a dendrite-inhibiting polymer separator with an elastic modulus of 16 GPa. The separator resists the movement of lithium through the generation of stresses in the cell. These stresses affect the negative electrode through two mechanisms altering the thermodynamics of the negative electrode and deforming the negative electrode mechanically. From this analysis, we find that the dendrite-inhibiting separator causes plastic and elastic deformation of the lithium at the negative electrode which flattens the electrode considerably when compared to the liquid-electrolyte case. This flattening of the negative electrode causes only very slight differences in the local state of charge in the positive electrode. When comparing the magnitude of the effects flattening the negative electrode, we find that the plastic deformation plays a much larger role than either the pressure-modified reaction kinetics or elastic deformation. This is due to the low yield strength of the lithium metal, which limits the stresses such that they have only a small effect on the reaction kinetics. (C) 2014 The Electrochemical Society. All rights reserved.

Ferrese, A↗

Mechanical properties of a porous mullite material

Modulus of rupture specimens were used to determine crack growth parameters of a porous mullite material. Strength testing was performed in ambient and moist environments. The power law crack growth rate parameters n and 1n B in 50 percent relative humidity were found to be 44.98 and 0.94, respectively. The inert strength, fracture toughness, and elastic modulus were also determined and found to be 19 MPa, 055 MPa(m) exp 1/2, and 11.6 GPa, respectively.

Viens, Michael J.↗

Graphite Nanoreinforcements for Aerospace Nanocomposites

New advances in the reinforcement of polymer matrix composite materials are critical for advancement of the aerospace industry. Reinforcements are required to have good mechanical and thermal properties, large aspect ratio, excellent adhesion to the matrix, and cost effectiveness. To fulfill the requirements, nanocomposites in which the matrix is filled with nanoscopic reinforcing phases having dimensions typically in the range of 1nm to 100 nm show considerably higher strength and modulus with far lower reinforcement content than their conventional counterparts. Graphite is a layered material whose layers have dimensions in the nanometer range and are held together by weak Van der Waals forces. Once these layers are exfoliated and dispersed in a polymer matrix as nano platelets, they have large aspect ratios. Graphite has an elastic modulus that is equal to the stiffest carbon fiber and 10-15 times that of other inorganic reinforcements, and it is also electrically and thermally conductive. If the appropriate surface treatment can be found for graphite, its exfoliation and dispersion in a polymer matrix will result in a composite with excellent mechanical properties, superior thermal stability, and very good electrical and thermal properties at very low reinforcement loadings.

Drzal, Lawrence T.↗

Effect of Methyl Groups on Formation of Ordered or Layered Graphitic Materials from Aromatic Molecules

Abstract Developing functionally complex carbon materials from small aromatic molecules requires an understanding of how the chemistry and structure of its constituent molecules evolve and crosslink, to achieve a tailorable set of functional properties. Here, molecular dynamics (MD) simulations are used to isolate the effect of methyl groups on condensation reactions during the oxidative process and evaluate the impact on elastic modulus by considering three monodisperse pyrene‐based systems with increasing methyl group fraction. A parameter to quantify the reaction progression is designed by computing the number of new covalent bonds formed. Utilizing the previously developed MD framework, it is found that increasing methylation leads to an almost doubling of bond formation, a larger fraction of the new bonds oriented in the direction of tensile stress, and a higher basal plane alignment of the precursor molecules along the direction of tensile stress, resulting in enhanced tensile modulus. Additionally, via experiments, it is demonstrated that precursors with a higher fraction of methyl groups result in a higher alignment of molecules. Moreover, increased methylation results in the lower spread of single molecule alignment which may lead to smaller variations in tensile modulus and more consistent properties in carbon materials derived from methyl‐rich precursors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Repeatability and Reproducibility of Compression Strength Measurements Conducted According to ASTM E9

Ten commercial laboratories participated in an interlaboratory study to establish the repeatability and reproducibility of compression strength tests conducted according to ASTM International Standard Test Method E9. The test employed a cylindrical aluminum AA2024-T351 test specimen. Participants measured elastic modulus and 0.2 % offset yield strength, YS(0.2 % offset), using an extensometer attached to the specimen. The repeatability and reproducibility of the yield strength measurement, expressed as coefficient of variations were cv(sub r)= 0.011 and cv(sub R)= 0.020 The reproducibility of the test across the laboratories was among the best that has been reported for uniaxial tests. The reported data indicated that using diametrically opposed extensometers, instead of a single extensometer doubled the precision of the test method. Laboratories that did not lubricate the ends of the specimen measured yield stresses and elastic moduli that were smaller than those measured in laboratories that lubricated the specimen ends. A finite element analysis of the test specimen deformation for frictionless and perfect friction could not explain the discrepancy, however. The modulus measured from stress-strain data were reanalyzed using a technique that finds the optimal fit range, and applies several quality checks to the data. The error in modulus measurements from stress-strain curves generally increased as the fit range decreased to less than 40 % of the stress range.

Luecke, William E.↗

A fluid pressure and deformation analysis for geological sequestration of carbon dioxide

We present a hydro-mechanical model and deformation analysis for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the two-way coupling between the geomechanical response and the fluid flow process in greater detail. In order for analytical solutions, the simplified hydro-mechanical model includes the geomechanical part that relies on the theory of linear elasticity, while the fluid flow is based on the Darcy’s law. The model was derived through coupling the two parts using the standard linear poroelasticity theory. Analytical solutions for fluid pressure field were obtained for a typical geological sequestration scenario and the solutions for ground deformation were obtained using the method of Green’s function. Solutions predict the temporal and spatial variation of fluid pressure, the effect of permeability and elastic modulus on the fluid pressure, the ground surface uplift, and the radial deformation during the entire injection period.

54 ENVIRONMENTAL SCIENCES↗

Size-dependent elastic properties of single-walled ZnO nanotubes: A first-principles study

By means of first-principles calculations, we have investigated a size dependence of elastic modulus in single-walled ZnO nanotubes with armchair and zigzag forms. It is found that for these tubes the Young's modulus is increased dramatically with the increased diameters and inversely proportional to the Zn-O bond length. Further, the amount of charge transfer, calculated by the Bader analysis, is introduced to elucidate the strength of bonding between Zn and O atoms in these tubes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Topographies of plasma-hardened surfaces of poly(dimethylsiloxane)

We studied the formation of surface layers hardened by plasma-enhanced oxidation of the silicone elastomer poly(dimethylsiloxane). We explored the largest parameter space surveyed to date. The surface layers may wrinkle, crack, or both, under conditions that at times are controlled by design, but more often have been discovered by trial-and-error. We find four distinct topographies: flat/wrinkled/cracked/cracked and wrinkled. Each topography is clearly separated in the space of plasma dose versus plasma pressure. We analyzed wrinkle amplitude and wavelength by atomic force microscopy in the tapping mode. From these dimensions we calculated the elastic modulus and thickness of the hard surface layer, and inferred a graded hardness, by employing a modified theoretical model. Our main result is the identification of the parameters under which the technologically important pure wrinkled, crack-free topography is obtained.

36 MATERIALS SCIENCE↗

Influence of temperature on the lattice misfit and elastic moduli of a Ni based single crystal superalloy with high volume fraction of γ′ phase

Highlights: • The variation of the lattice misfit with temperature in a Ni based single-crystal superalloy with high volume fraction of γ' phase was determined by high-temperature X-ray diffraction (HT-XRD) technique at temperatures between 25 °C and 1200 °C. • When the temperature was higher than 1100 °C, the γ' phase obviously dissolved, leading to a lower content of Mo and Re in the γ phase, and then resulted in a smaller absolute value of the lattice misfit. • The contribution of dissolution of γ′ phase to the reduction of the misfit increased with rising temperature and reached 29.5% at 1200 °C. • When the temperature exceeded 1100 °C, the difference of elastic moduli of γ and γ′ phases increased with rising temperature was attributed to the elastic modulus of γ phase decreased significantly. - Abstract: The variation of the lattice parameter with temperature in a Ni based single-crystal superalloy with high volume fraction of γ′ phase IC32 was determined by high-temperature X-ray diffraction (HT-XRD) technique at temperatures between 25 °C and 1200 °C. The effects of the temperature, especially the ultra-high temperature (beyond 1100 °C), on lattice misfit, elastic moduli, γ′ volume fraction and composition of γ, γ′ phases were investigated in this study. The results show that the absolute value of lattice misfit first increased and then decreased with increasing temperature and reached the maximum of 0.53% at 1100 °C. When the temperature was higher than 1100 °C, the γ′ precipitate obviously dissolved, leading to a lower content of Mo and Re in the γ phase, and then resulted in a smaller absolute value of lattice misfit. The contribution of dissolution of γ′ phase to the reduction of the misfit increased with rising temperature and reached 29.5% at 1200 °C. Moreover, when the temperature was above 1100 °C, the elastic moduli of the γ phase and alloy decreased significantly, while this phenomenon was not observed in the γ′ phase.

36 MATERIALS SCIENCE↗

Non-linear elastic-plastic behavior of the invert glass lithium phosphorous oxynitride (LiPON)

Micro and nano-scale mechanical behavior of network/ionic glasses is dictated by their composition and the number of constraints per structural unit. From this perspective, the glass LiPON presents the opportunity for enhancement of the microscale ductility due to its rather unconstrained orthophosphate structure. Here, we use instrumented nanoindentation with different tip geometries to investigate the mechanical response of LiPON glass. The results reveal that the elastic modulus of LiPON is not constant and depends on pressure. With the method utilizing spherical nanoindentation and continuous stiffness measurement (CSM) we determine the yield point of LiPON. We propose the Drucker-Prager type of yield criterion for LiPON and estimate its yield stress in compression as 2.4 GPa. There exists another stress threshold, however, around 490 MPa, at which the elastic deformation becomes non-linear, and this can be mistaken for the yield stress.

Constitutive model↗

Mechanical behavior and failure mechanisms of Li-ion battery separators

We determine and compare anisotropic mechanical properties for three types of commercially available Li-ion battery separators: Celgard 2325, Celgard PP2075 dry-processed polymer separators, and DreamWeaver Gold 40 non-woven separator. Significant amount of anisotropy of properties was determined, with the Young's modulus being different by up to a factor of 5 and ultimate strength being different by a factor of 10 between orthogonal directions within a polymer separator layer. Strain rate sensitivity was investigated by applying strain rates ranging from 1•10 -4 s -1 to 0.1 s -1 . Significant strengthening was observed and the strain rate strengthening coefficients were determined for both elastic modulus and yield stress in case of polymer separators. Digital image correlation technique was used to measure and map the strains over the specimen's gage section. A significant strain concentration in bands running perpendicular to the tensile axis was observed in polymer separator samples oriented in transverse direction. Such localized necking allows for extremely high strains close to 300% to develop in the material. Furthermore, the failure mode was remarkably different for all three types of separators which adds additional variable in safe design of Li-ion batteries for prevention of internal short circuits.

25 ENERGY STORAGE↗

An FEM-Based Peridynamic Model for Failure Analysis of Unidirectional Fiber-Reinforced Laminates

To predict the mixed damage modes of unidirectional fiber-reinforced polymer (FRP) laminates under dynamic loading, an FEM-based peridynamic model is introduced in this paper. Based on its geometric structure and material composition, a long fiber lamina is considered a transversely isotropic medium as a result of homogenization at the meso-scale. The laminated structure is modeled by stacking surface mesh layers with arbitrary fiber angles along the thickness direction. The peridynamic bonds between Gauss points connect the separated elements. These bonds are classified as inner-layer bonds and inter-layer bonds. To represent the anisotropy of a laminate, the micro-elastic modulus of the inner-layer and inter-layer bonds is calculated from the anisotropic engineering material constants separately. To capture complex failure behaviors of laminate structures, an empirical damage model is proposed for the tension/ compression breakage of peridynamic bonds. This damage model can control the in-plane and delamination failure process. Finally, benchmark tests are conducted to validate the elastic response of laminates under dynamic loading. In terms of damage analysis, the proposed model can capture the complex damage modes and resistive force of laminate structures.

36 MATERIALS SCIENCE↗

Characterisation of titanium-titanium boride composites processed by powder metallurgy techniques

In this work, a detailed characterisation of titanium-titanium boride composites processed by three powder metallurgy techniques, namely, hot isostatic pressing, spark plasma sintering and vacuum sintering, was conducted. Two composites with different volume percents of titanium boride reinforcement were used for the investigation. One was titanium with 20% titanium boride, and the other was titanium with 40% titanium boride (by volume). Characterisation was performed using X-ray diffraction, electron probe micro analysis - energy dispersive spectroscopy and wavelength dispersive spectroscopy, image analysis and scanning electron microscopy. The characterisation results confirm the completion of the titanium boride reaction. The results reveal the presence of titanium boride reinforcement in different morphologies such as needle-shaped whiskers, short agglomerated whiskers and fine plates. The paper also discusses how mechanical properties such as microhardness, elastic modulus and Poisson's ratio are influenced by the processing techniques as well as the volume fraction of the titanium boride reinforcement. - Highlights: Black-Right-Pointing-Pointer Ti-TiB composites were processed by HIP, SPS and vacuum sintering. Black-Right-Pointing-Pointer The completion of Ti-TiB{sub 2} reaction was confirmed by XRD, SEM and EPMA studies. Black-Right-Pointing-Pointer Hardness and elastic properties of Ti-TiB composites were discussed. Black-Right-Pointing-Pointer Processing techniques were compared with respect to their microstructure.

36 MATERIALS SCIENCE↗

Ultrasound nondestructive characterization of transparent spinel

Ceramic materials have attractive attributes for applications that experience high stresses or strain rates. Compared to metal-based systems, ceramics offer a lower areal density which reduces weight, but do not depreciate the integrity of other properties. The ability to tailor the microstructure of ceramics used in armor systems is a common way to increase specific mechanical properties or obtain certain material characteristics. Properties such as elastic modulus, hardness, and density are those that are typically desired to be enhanced. By modifying the microstructure one can obtain a ceramic with these enhanced properties as well as high optical transmission across a wide range of the electromagnetic spectrum. The testing of these properties and ballistic performance is usually destructive, expensive, and time consuming. Common assessments using ultrasonic NDE usually include spatially locating large flaws, sonic velocity measurements, and elastic property measurements. The use of acoustic spectroscopy to go beyond typical ultrasonic NDE in structural ceramics and allow for the use of a microstructural characterization tool is investigated in this paper. Ultrasound absorption by lithium fluoride precipitates in aluminate spinel (MgAl{sub 2}O{sub 4}) present as defined spectral peaks. Average heterogeneity size determination in magnesium aluminate spinel MgAl{sub 2}O{sub 4} by method of acoustic spectroscopy is shown.

36 MATERIALS SCIENCE↗

Emergent SO( 3 ) Symmetry of the Frictionless Shear Jamming Transition

Here, we study the shear jamming of athermal frictionless soft spheres, and find that in the thermodynamic limit, a shear-jammed state exists with different elastic properties from the isotropically-jammed state. For example, shear-jammed states can have a non-zero residual shear stress in the thermodynamic limit that arises from long-range stress-stress correlations. As a result, the ratio of the shear and bulk moduli, which in isotropically-jammed systems vanishes as the jamming transition is approached from above, instead approaches a constant. In contrast to these striking differences, we argue that in a deeper sense, the shear jamming and isotropic jamming transitions actually have the same symmetry, and that the differences can be fully understood by rotating the six-dimensional basis of the elastic modulus tensor.

36 MATERIALS SCIENCE↗

Probing the elastic response of microalga Scenedesmus dimorphus in dry and aqueous environments through atomic force microscopy

With the re-emergence of microalgae as a replacement feedstock for petroleum-derived oils, researchers are working to understand its chemical and mechanical behavior. In this work, the mechanical properties of microalgae, Scenedesmus dimorphus, were investigated at the subcellular level to determine the elastic response of cells that were in an aqueous and dried state using nano-scale indentation through atomic force microscopy. The elastic modulus of single-celled S. dimorphus cells increased over tenfold from an aqueous state to a dried state, which allows us to better understand the biophysical response of microalgae to stress.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗