Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic stiffness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Control of a flexible planar truss using proof mass actuators

A flexible structure was modeled and actively controlled by using a single space realizable linear proof mass actuator. The NASA/UVA/UB actuator was attached to a flexible planar truss structure at an optimal location and it was considered as both passive and active device. The placement of the actuator was specified by examining the eigenvalues of the modified model that included the actuator dynamics, and the frequency response functions of the modified system. The electronic stiffness of the actuator was specified, such that the proof mass actuator system was tuned to the fourth structural mode of the truss by using traditional vibration absorber design. The active control law was limited to velocity feedback by integrating of the signals of two accelerometers attached to the structure. The two lower modes of the closed-loop structure were placed further in the LHS of the complex plane. The theoretically predicted passive and active control law was experimentally verified.

Minas, Constantinos↗
NASA NTRS1994

Analysis of the Effects of Surface Pitting and Wear on the Vibrations of a Gear Transmission System

A comprehensive procedure to simulate and analyze the vibrations in a gear transmission system with surface pitting, 'wear' and partial tooth fracture of the gear teeth is presented. An analytical model was developed where the effects of surface pitting and wear of the gear tooth were simulated by phase and magnitude changes in the gear mesh stiffness. Changes in the gear mesh stiffness were incorporated into each gear-shaft model during the global dynamic simulation of the system. The overall dynamics of the system were evaluated by solving for the transient dynamics of each shaft system simultaneously with the vibration of the gearbox structure. In order to reduce the number of degrees-of-freedom in the system, a modal synthesis procedure was used in the global transient dynamic analysis of the overall transmission system. An FFT procedure was used to transform the averaged time signal into the frequency domain for signature analysis. In addition, the Wigner-Ville distribution was also introduced to examine the gear vibration in the joint time frequency domain for vibration pattern recognition. Experimental results obtained from a gear fatigue test rig at NASA Lewis Research Center were used to evaluate the analytical model.

Choy, F. K.↗
NASA NTRS2015

Subharmonic Oscillations and Chaos in Dynamic Atomic Force Microscopy

The increasing use of dynamic atomic force microscopy (d-AFM) for nanoscale materials characterization calls for a deeper understanding of the cantilever dynamics influencing scan stability, predictability, and image quality. Model development is critical to such understanding. Renormalization of the equations governing d- AFM provides a simple interpretation of cantilever dynamics as a single spring and mass system with frequency dependent cantilever stiffness and damping parameters. The renormalized model is sufficiently robust to predict the experimentally observed splitting of the free-space cantilever resonance into multiple resonances upon cantilever-sample contact. Central to the model is the representation of the cantilever sample interaction force as a polynomial expansion with coefficients F(sub ij) (i,j = 0, 1, 2) that account for the effective interaction stiffness parameter, the cantilever-to-sample energy transfer, and the amplitude of cantilever oscillation. Application of the Melnikov method to the model equation is shown to predict a homoclinic bifurcation of the Smale horseshoe type leading to a cascade of period doublings with increasing drive displacement amplitude culminating in chaos and loss of image quality. The threshold value of the drive displacement amplitude necessary to initiate subharmonic generation depends on the acoustic drive frequency, the effective damping coefficient, and the nonlinearity of the cantilever-sample interaction force. For parameter values leading to displacement amplitudes below threshold for homoclinic bifurcation other bifurcation scenarios can occur, some of which lead to chaos.

Cantrell, John H.↗
NASA NTRSDate not supplied

Error Localization Examples: Looking for a Needle in a Hay-stack

Finite element models (FEM) are routinely developed and used during fabrication of high dollar-value hardware. NASA as part of the pre-flight certification of launch vehicles routinely conducts vibration and static tests to calibrate models used for flight-risk assessments. As part of the calibration process, certain areas in the model are modified, using engineering judgment and sensitivity analysis, to match the test results. Unfortunately, tools to identify problem areas in the FEM using test data directly are scarce. Over the years, Error Localization Algorithms (ELA) have been proposed with very limited success. Recently, the Analytical Dynamics Model Improvement (ADMI) algorithm, which computes closed-form mass and stiffness corrections to match the test data exactly, have been shown to be effective for error localization. The paper will present several FEM example problems where ELA is used with simulated test data to determine FEM problem areas. For each example, the correct answer is shown along with ELA results. It is shown that the ELA process is able to identify general problem areas in the FEM, which are consistent with known model perturbations. However, in most cases the ELA identified area of improvement is larger than the true answer. Nonetheless, with proper optimization tools, calibration results using the ELA identified areas provide excellent results.

error localization↗
NASA NTRSDate not supplied

Error Localization Examples: Looking for a Needle in a Haystack

Finite element models (FEM) are routinely developed and used during fabrication of high dollar-value hardware. NASA, as part of the pre-flight certification of launch vehicles, routinely conducts vibration and static tests to calibrate models used for flight-risk assessments. During model calibration, certain areas of the model are modified, using engineering judgment and sensitivity analysis, to match the test results. Unfortunately, tools to identify problem areas in the FEM using test data directly are scarce and infrequently applied. Over the years, error localization algorithms have been proposed with very limited success. Recently, the Analytical Dynamics Model Improvement (ADMI) algorithm, which computes closed-form mass and stiffness corrections to match the test data exactly, have been shown to be an effective Error Localization Algorithm (ELA). The paper discusses three examples where ELA is used with simulated test data to locate problem areas. To gain confidence in the approach, the exact answer is shown along with ELA results. Results show that ELA is able to identify general problem areas consistent with known problem areas. In all examples, the ELA identified area is larger than the exact problem area. Nonetheless, with proper optimization tools, calibration results using the ELA identified areas provide excellent results.

model calibration↗
NASA NTRS1996

Steady-State Dynamic Behavior of a Flexible Rotor With Auxiliary Support From a Clearance Bearing

This paper investigates the steady-state responses of a rotor system supported by auxiliary bearings in which there is a clearance between the rotor and the inner race of the bearing. A simulation model based upon the rotor of a production jet engine is developed and its steady-state behavior is explored over a wide range of operating conditions for various parametric configurations. Specifically, the influence of rotor imbalance, clearance, support stiffness and damping is studied. Bifurcation diagrams are used as a tool to examine the dynamic behavior of this system as a function of the afore mentioned parameters. The harmonic balance method is also employed for synchronous response cases. The observed dynamical responses is discussed and some insights into the behavior of such systems are presented.

Xie, Huajun↗
DOE OSTI2023

Vibro-impact analysis and characterization of pipeline conveying fluids with multi-segmented motion-limiting constraints

Previous studies of the cantilevered pipeline conveying fluid system have included motion-limiting constraints in the form of trilinear springs. While this is desirable in experimental scenarios, it may not be representative of real-world applications. Therefore, here, this study focuses on multi-segmented motion-limiting constraints. As this type of motion-limiting constraint has not been investigated with a cantilevered pipeline system, a wide variety of outer and inner constraint stiffness and constraint gap sizes are investigated in this study to gain a comprehensive understanding of how the multi-segmented constraints affect the dynamics of the cantilevered pipeline. In this effort, bifurcation diagrams, phase portraits, Poincare maps, time histories, and power spectra are used to investigate the dynamics of the system, and the fluid flow speeds where dynamic characteristics are considered. In general, it is found that critical flow speeds like when the pipe sticks in the constraints are reduced as the constraint stiffnesses are increased. Additionally, the sticking flow speed occurred at lower flow speeds as the gap sizes of the inner and outer constraints decrease, and a larger constraint offset results in a smaller inner gap size leading to critical behaviors occurring at earlier flow speeds.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1995

NASA-GRA--Geared-Rotor Analyzer

NASA-GRA computer program designed to solve for steady-state dynamic responses of multigeared rotor systems. Based on transfer-matrix method combined with harmonic-balance method. Includes accurate gear-mesh model for spur and helical gears, containing time-varying mesh stiffnesses, gear-mounting errors, and gear-profile errors. Also includes accurate disk model containing inertia-based dynamic coupling terms due to mass and skew unbalances and massless-elastic-shaft model and linearly coupled fluid-film bearing model. Written in FORTRAN 77.

Park, N.↗
DOE OSTI2022

An energy-based study of the embedded element method for explicit dynamics

Abstract The embedded finite element technique provides a unique approach for modeling of fiber-reinforced composites. Meshing fibers as distinct bundles represented by truss elements embedded in a matrix material mesh allows for the assignment of more specific material properties for each component rather than homogenization of all of the properties. However, the implementations of the embedded element technique available in commercial software do not replace the material of the matrix elements with the material of the embedded elements. This causes a redundancy in the volume calculation of the overlapping meshes leading to artificially increased stiffness and mass. This paper investigates the consequences in the energy calculations of an explicit dynamic model due to this redundancy. A method for the correction of the edundancy within a finite element code is suggested which removes extra energy and is shown to be effective at correcting the energy calculations for large amounts of redundant volume.

Martin, Valerie A.↗
DOE OSTI2021

Nonlinear Interface Reduction for Time-Domain Analysis of Hurty/Craig-Bampton Superelements with Frictional Contact

Virtual prototyping in engineering design relies today on modern numerical models of contacting structures with accurate resolution of interface mechanics, which strongly affect the system-level stiffness and energy dissipation due to frictional losses. High-fidelity modeling within the localized interfaces is required to resolve local quantities of interest that may drive design decisions. The high-resolution finite element meshes necessary to resolve inter-component stresses tend to be computationally expensive, particularly when the analyst is interested in response time histories. The Hurty/Craig-Bampton (HCB) transformation is a widely used method in structural dynamics for reducing the interior portion of a finite element model while having the ability to retain all nonlinear contact degrees of freedom (DOF) in physical coordinates. These models may still require many DOF to adequately resolve the kinematics of the interface, leading to inadequate reduction and computational savings. This study proposes a novel interface reduction method to overcome these challenges by means of system-level characteristic constraint (SCC) modes and properly orthogonal interface modal derivatives (POIMDs) for transient dynamic analyses. Both SCC modes and POIMDs are computed using the reduced HCB mass and stiffness matrices, which can be directly computed from many commercial finite element analysis software. Comparison of time history responses to an impulse-type load in a mechanical beam assembly indicate that the interface-reduced model correlates well with the HCB truth model. Localized features like slip and contact area are well-represented in the time domain when the beam assembly is loaded with a broadband excitation. The proposed method also yields reduced-order models with greater critical timestep lengths for explicit integration schemes.

42 ENGINEERING↗
NASA NTRS1989

Results of a parametric aeroelastic stability analysis of a generic X-wing aircraft

This paper discusses the trends in longitudinal dynamic aeroelastic stability of a generic x-wing aircraft model with design parameter variations. X-wing rotor blade sweep angle, ratio of blade mass to total vehicle mass, blade structural stiffness cross-coupling and vehicle center-of-gravity location were parameters considered. The typical instability encountered is body-freedom flutter involving a low frequency interaction of the first elastic mode and the aircraft short period mode. Parametric cases with the lowest static margin consistently demonstrated the highest flutter dynamic pressures. As mass ratio was increased, the flutter boundary decreased. The decrease was emphasized as center-of-gravity location was moved forward. As sweep angle varied, it was observed that the resulting increase in forward-swept blade bending amplitude relative to aft blade bending amplitude in the first elastic mode had a stabilizing effect on the flutter boundary. Finally, small amounts of stiffness cross-coupling in the aft blades increased flutter dynamic pressure.

Woods, Jessica A.↗
NASA NTRS1989

Results of a parametric aeroelastic stability analysis of a generic X-wing aircraft

This paper discusses the trend in longitudinal dynamic aeroelastic stability of a generic X-Wing aircraft model with design parameter variations. X-Wing rotor blade sweep angle, ratio of blade mass to total vehicle mass, blade structural stiffness cross-coupling and vehicle center-of-gravity location were parameters considered. The typical instability encountered is body-freedom flutter involving a low frequency interaction of the first elastic mode and the aircraft short period mode. Parametric cases with the lowest static margin consistently demonstrated the highest flutter dynamic pressures. As mass ratio was increased, the flutter boundary decreased. The decrease was emphasized as center-of-gravity location was moved forward. As sweep angle varied, it was observed that the resulting increase in forward-swept blade bending amplitude relative to aft blade bending amplitude in the first elastic mode had a stabilizing effect on the flutter boundary. Finally, small amounts of stiffness cross-coupling in the aft blades increased flutter dynamic pressure.

Woods, Jessica A.↗
DOE OSTI2025

A physics-constrained neural ordinary differential equations approach for robust learning of stiff chemical kinetics

The high computational cost associated with solving for detailed chemistry poses a significant challenge for predictive computational fluid dynamics (CFD) simulations of turbulent reacting flows. While deep learning techniques have been explored to develop faster surrogate models, they often fail to integrate reliably with CFD solvers. This instability arises because traditional deep learning approaches optimize for training error without ensuring compatibility with ordinary differential equation (ODE) solvers, resulting in accumulation of errors over time. Recently, neuralODE (NODE) based approaches have been shown to be a promising technique to emulate and accelerate detailed chemistry computations. Here, in the present work, we extend this NODE framework for stiff chemical kinetics by incorporating mass conservation constraints directly into the loss function during training. This ensures that the total mass as well as the individual elemental species masses are conserved in an a-posteriori manner. Proof-of-concept studies are performed with the novel physics-constrained NODE (PC-NODE) approach for homogeneous autoignition of hydrogen-air mixture over a range of composition and thermodynamic conditions. It is demonstrated that the PC-NODE framework not only improves the physical consistency of the resulting data-driven model with respect to mass conservation criteria, but also improves training efficiency. PC-NODE is shown to achieve 2–100× speedup relative to the hydrogen-air detailed chemical mechanism depending on the type of the ODE solver (implicit or explicit) used during autoregressive inference tests. Lastly, a-posteriori studies are performed wherein the trained PC-NODE model is coupled with a CFD solver. It is shown that higher accuracy is achieved with PC-NODE relative to the purely data-driven NODE approach. Moreover, PC-NODE also exhibits robustness and generalizability to unseen initial conditions from within (interpolative capability) as well as outside (extrapolative capability) the training regime.

computational combustion↗
NASA NTRS1973

Reduction of truncation errors in modal analysis

A condensation method and computer program are described for large discrete parameter vibration analysis of complex structures that greatly reduces truncation errors and provides accurate definition of modes in a selected frequency range. A dynamic transformation is obtained from the partitioned equations of motion that relates modes not explicitly in the condensed solution to the retained modes at a selected system frequency. The generalized mass and stiffness matrices, obtained with existing modal synthesis methods, are reduced using this transformation and solved. Revised solutions are then obtained using new transformations at the calculated eigenvalues and are also used to assess the accuracy of the results. Computations are made tractable by simplified forms of the transformation that result with various modal synthesis methods. Three examples using the dynamic transformation in conjunction with a General Electric stiffness coupling method and the method of Craig and Bampton indicate large reductions in truncation errors and demonstrate the method for sequential groups of modes.

Kuhar, E. J.↗
NASA NTRS1981

Automated dynamic analytical model improvement

A method is developed and illustrated which finds minimum changes in analytical mass and stiffness matrices to make them consistent with a set of measured normal modes and natural frequencies. The corrected model is an improved base for studies of physical changes, changes in boundary conditions, and for prediction of forced responses. Features of the method are: efficient procedures not requiring solutions of the eigenproblem; the model may have more degrees of freedom than the test data; modal displacements at all the analytical degrees of freedom are obtained; the frequency dependence of the coordinate transformations are properly treated.

Berman, A.↗
DOE OSTI2023

The Stability Transition From Stable to Unstable Frictional Slip With Finite Pore Pressure

Pore fluids are ubiquitous throughout the lithosphere and are commonly invoked as the cause of induced seismicity and slow earthquakes. We perform lab experiments to address these questions for drained fault conditions and low pore pressure. We shear simulated faults at effective normal stress (σ' n ) of 20 MPa and pore pressures Pp from 1 to 4 MPa. We document the full range of lab earthquake behaviors from slow slip to elasto-dynamic rupture and show that slow slip can be explained by the slip rate dependence of the critical rheologic stiffness without dilatancy hardening or other fluid effects. Our fault permeabilities ranges from 10 –18 to 10 –17 m 2 with an initial porosity of 0.1 and estimated fluid diffusion time ≈1 s. Slow slip and quasi-dynamic fault motion may arise from high P p at higher pressures but dilatancy strengthening is not a general requirement.

58 GEOSCIENCES↗
NASA NTRS1963

Investigation of Propeller-power-plant Autoprecession Boundaries for a Dynamic-aeroelastic Model of a Four-engine Turboprop Transport Airplane

A flexibly mounted aircraft engine may under certain conditions experience a self-excited whirling instability involving a coupling between the gyroscopic and aerodynamic forces acting on the propeller, and the inertial, elastic, and damping forces contributed by the power plant, nacelle, and wing. This phenomenon has been called autoprecession, or whirl instability. An experimental investigation was made in the Langley transonic dynamics tunnel at Mach numbers below 0.3 to study some of the pertinent parameters influencing the phenomenon. These parameters included propeller rotational speed, stiffness of the power-plant assembly in the pitch and yaw planes and the ratio of pitch stiffness to yaw stiffness, structural damping of the power-plant assembly in the pitch and yaw planes, simulated fuel load in the wings, and the location and number of autoprecessing powerplant assemblies. A large dynamic-aeroelastic model of a four-engine turboprop transport airplane mounted on a vertical rod in a manner which provided several limited body degrees of freedom was used in the investigation. It was found that the boundary for autoprecession decreased markedly with Increasing proreduction of power-plant stiffness and/or damping, and to a lesser degree decreased with reduction of simulated fuel load in the wings. peller rotational speed generally lowered the autoprecession boundary. This effect was more pronounced as the stiffness was increased. An inboard power plant was found to be more susceptible to autoprecession than an outboard one. Combinations in which two or more power plants had the same level of reduced stiffness resulted in autoprecession boundaries considerably lower than that of a single power plant with the same level of reduced stiffness.

POWER PLANT↗
NASA NTRS1974

User's Manual for Computer Program ROTOR

A detailed description of a computer program to calculate tilt-rotor aircraft dynamic characteristics is presented. This program consists of two parts: (1) the natural frequencies and corresponding mode shapes of the rotor blade and wing are developed from structural data (mass distribution and stiffness distribution); and (2) the frequency response (to gust and blade pitch control inputs) and eigenvalues of the tilt-rotor dynamic system, based on the natural frequencies and mode shapes, are derived. Sample problems are included to assist the user.

Yasue, M.↗