Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Derived Matrices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

NASTRAN/FLEXSTAB procedure for static aeroelastic analysis

Presented is a procedure for using the FLEXSTAB External Structural Influence Coefficients (ESIC) computer program to produce the structural data necessary for the FLEXSTAB Stability Derivatives and Static Stability (SD&SS) program. The SD&SS program computes trim state, stability derivatives, and pressure and deflection data for a flexible airplane having a plane of symmetry. The procedure used a NASTRAN finite-element structural model as the source of structural data in the form of flexibility matrices. Selection of a set of degrees of freedom, definition of structural nodes and panels, reordering and reformatting of the flexibility matrix, and redistribution of existing point mass data are among the topics discussed. Also discussed are boundary conditions and the NASTRAN substructuring technique.

Schuster, L. S.↗
DOE OSTI2022

Dynamics of photosynthetic light harvesting systems interacting with N-photon Fock states

Here, we develop a method to simulate the excitonic dynamics of realistic photosynthetic light harvesting systems, including non-Markovian coupling to phonon degrees of freedom, under excitation by N-photon Fock state pulses. This method combines the input–output and the hierarchical equations of motion formalisms into a double hierarchy of density matrix equations. We show analytically that under weak field excitation relevant to natural photosynthesis conditions, an N-photon Fock state input and a corresponding coherent state input give rise to equal density matrices in the excited manifold. However, an N-photon Fock state input induces no off-diagonal coherence between the ground and excited subspaces, in contrast with the coherences created by a coherent state input. We derive expressions for the probability to absorb a single Fock state photon with or without the influence of phonons. For short pulses (or, equivalently, wide bandwidth pulses), we show that the absorption probability has a universal behavior that depends only upon a system-dependent effective energy spread parameter Δ and an exciton–light coupling constant Γ. This holds for a broad range of chromophore systems and for a variety of pulse shapes. We also analyze the absorption probability in the opposite long pulse (narrow bandwidth) regime. We then derive an expression for the long time emission rate in the presence of phonons and use it to study the difference between collective vs independent emission. Finally, we present a numerical simulation for the LHCII monomer (14-mer) system under single photon excitation that illustrates the use of the double hierarchy equations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

JIMWLK on a quantum computer

We propose a method for solving the Jalilian-Marian-Iancu-McLerran-Weigert-Leonidov-Kovner (JIMWLK) evolution equation on quantum computers. Our approach exploits the reformulation of the JIMWLK equation as a Lindblad master equation governing the rapidity evolution of the hadronic density matrix, as established in prior work. To render the problem tractable for quantum simulation, we introduce several approximations: the two-dimensional transverse plane is reduced to a one-dimensional radial lattice by assuming azimuthal symmetry of the jump operators; the gauge group is restricted to SU(2); and the infinite Wilson lines of the JIMWLK equation are replaced by finite Wilson links along the light-cone direction. The resulting bosonic Hilbert space is truncated using the electric field basis familiar from Hamiltonian lattice gauge theory, with states restricted to angular momenta 𝑗 ≤ 𝑗 max . We derive the matrix elements of the JIMWLK Lindblad jump operators in this basis. As a benchmark, we demonstrate rapid convergence of the fundamental dipole expectation value with 𝑗 max for both pure and mixed Gaussian initial density matrices. For the simplest truncation, 𝑗 max =1/2, we implement the Lindblad evolution using a quantum simulation algorithm verified with the Qiskit statevector simulator by decomposing the non-unitary evolution operator into a linear combination of unitaries. This work establishes a concrete pathway toward quantum simulation of high-energy quantum chromodynamics evolution equations, with direct relevance to the physics program of the Electron-Ion Collider.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1987

User's manual for LINEAR, a FORTRAN program to derive linear aircraft models

This report documents a FORTRAN program that provides a powerful and flexible tool for the linearization of aircraft models. The program LINEAR numerically determines a linear system model using nonlinear equations of motion and a user-supplied nonlinear aerodynamic model. The system model determined by LINEAR consists of matrices for both state and observation equations. The program has been designed to allow easy selection and definition of the state, control, and observation variables to be used in a particular model.

Duke, Eugene L.↗
NASA NTRS1979

A computer program to generate equations of motion matrices, L217 (EOM). Volume 1: Engineering and usage

The equations of motion program L217 formulates the matrix coefficients for a set of second order linear differential equations that describe the motion of an airplane relative to its level equilibrium flight condition. Aerodynamic data from FLEXSTAB or Doublet Lattice (L216) programs can be used to derive the equations for quasi-steady or full unsteady aerodynamics. The data manipulation and the matrix coefficient formulation are described.

Kroll, R. I.↗
NASA NTRS1973

Apollo 16 rocks - Classification and petrogenetic model

The Apollo 16 rocks include cataclastic anorthosites, two varieties of unequilibrated breccia, two varieties of partly to fully equilibrated breccia, and a sequence of partially melted breccias. The latter, which dominate the Apollo 16 collection, include glass, divitrified glass, mesostasis-olivine-plagioclase rock, mesostasis-rich basalt, basalt, and poikilitic rocks. All sequence members contain vesicles and relics of plagioclase, olivine, pink spinel, and lithic fragments. Their equilibrated matrices define a series from glass, to a plagioclase-olivine-mesostasis assemblage displaying spherulitic and skeletal shaped crystals, through a plagioclase-pyroxene-olivine assemblage displaying euhedral shaped crystals. Such data suggest that the sequence lithologies were derived from breccias or soils that were partially melted in an impact event.

Warner, J. L.↗
DOE OSTI2023

On the convexity of phase-field fracture formulations: Analytical study and comparison of various degradation functions

Efficient and accurate fracture modeling is of great importance in applications where catastrophic outcomes under extreme scenarios are possible. The phase-field (PF) approach to fracture received significant attention over the past decade, due to its capability to capture complicated fracture patterns (e.g., crack merging and branching). Specifically, crack initiation and propagation are modeled via minimization of the total energy functional, which is regularized with the aid of a phase field. Despite the promising results and modeling capabilities of the PF method in many applications, the solution of fracture problems remains computationally challenging mainly due to the non-convexity of the total energy functional with respect to the combined unknown (phase field and displacement) fields. Understanding the effects of their coupling on convexity is crucial in order to address frequently encountered hurdles in fracture modeling (e.g., inefficient solvers and non-physical crack nucleation). In this paper, we develop convexity criteria for a wide class of PF fracture formulations. For this class of formulations, the second variation of the total energy functional is expressed in terms of Hessian matrices (evaluated at individual material points). Depending on the choice of geometric crack functions and degradation functions, we classify the formulations into three categories and analytically study each one separately. To study the sign of the second variation, we derive inequalities which are satisfied at material points when the Hessian matrix is locally positive semi-definite. These inequalities provide objective criteria for comparing degradation functions. Finally, the applicability of the proposed convexity criteria is demonstrated in the context of a one-dimensional problem, solved using a conventional monolithic solver.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Dynamic Graph Sequence Data from Simulated Neutron Reflectometry Measurements

This dataset comprises dynamic graph sequences derived from simulated in-situ neutron reflectometry measurements, capturing the gradual evolution of a layer structure over time. Each graph sequence represents a synthetic sample, with node features detailing the scattering vector and corresponding reflectivity measurements, while adjacency matrices have corresponding reference material parameters attached as metadata. The dataset spans multiple sets, each with a different number of sequences, offering a comprehensive basis for training models that handle dynamic input sequences with embedded physics. This dataset is particularly suited for tackling inverse problems with hidden physical states that evolve over time, challenges that are typically difficult to address using conventional iterative fitting methods.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Laboratory Studies of DIB Carriers

Spectroscopic studies of the following potential diffuse interstellar band (DIB) carriers are reviewed: unspecified organics, carbon chains, polycyclic aromatic hydrocarbons (PAHs), fullerenes and derivatives, as well as porphyrins and related material. An assessment of each is given, along with suggestions for further experimental studies needed to fully test each candidate. Of the experimental techniques in common use matrix isolation spectroscopy with neon matrices is the most appropriate for the DIBs. The low vapor pressure and high reactivity of these materials preclude gas phase studies on many of these species. At this point, given the type and quality of published data available, carbon chains and PARs are the most promising candidates for a number of the DIBs.

Allamandola, L. J.↗
NASA NTRS2003

Fault Tolerant Homopolar Magnetic Bearings

Magnetic suspensions (MS) satisfy the long life and low loss conditions demanded by satellite and ISS based flywheels used for Energy Storage and Attitude Control (ACESE) service. This paper summarizes the development of a novel MS that improves reliability via fault tolerant operation. Specifically, flux coupling between poles of a homopolar magnetic bearing is shown to deliver desired forces even after termination of coil currents to a subset of failed poles . Linear, coordinate decoupled force-voltage relations are also maintained before and after failure by bias linearization. Current distribution matrices (CDM) which adjust the currents and fluxes following a pole set failure are determined for many faulted pole combinations. The CDM s and the system responses are obtained utilizing 1D magnetic circuit models with fringe and leakage factors derived from detailed, 3D, finite element field models. Reliability results are presented vs. detection/correction delay time and individual power amplifier reliability for 4, 6, and 7 pole configurations. Reliability is shown for two success criteria, i.e. (a) no catcher bearing contact following pole failures and (b) re-levitation off of the catcher bearings following pole failures. An advantage of the method presented over other redundant operation approaches is a significantly reduced requirement for backup hardware such as additional actuators or power amplifiers.

Li, Ming-Hsiu↗
NASA NTRS2011

An In-Depth Tutorial on Constitutive Equations for Elastic Anisotropic Materials

An in-depth tutorial on the constitutive equations for elastic, anisotropic materials is presented. Basic concepts are introduced that are used to characterize materials, and notions about how anisotropic material deform are presented. Hooke s law and the Duhamel-Neuman law for isotropic materials are presented and discussed. Then, the most general form of Hooke s law for elastic anisotropic materials is presented and symmetry requirements are given. A similar presentation is also given for the generalized Duhamel-Neuman law for elastic, anisotropic materials that includes thermal effects. Transformation equations for stress and strains are presented and the most general form of the transformation equations for the constitutive matrices are given. Then, specialized transformation equations are presented for dextral rotations about the coordinate axes. Next, concepts of material symmetry are introduced and criteria for material symmetries are presented. Additionally, engineering constants of fully anisotropic, elastic materials are derived from first principles and the specialized to several cases of practical importance.

Nemeth, Michael P.↗
DOE OSTI2021

Time evolution of ML-MCTDH wavefunctions. I. Gauge conditions, basis functions, and singularities

We derive a family of equations-of-motion (EOMs) for evolving multi-layer multiconfiguration time-dependent Hartree (ML-MCTDH) wavefunctions that, unlike the standard ML-MCTDH EOMs, never require the evaluation of the inverse of singular matrices. All members of this family of EOMs make use of alternative static gauge conditions than those used for standard ML-MCTDH. These alternative conditions result in an expansion of the wavefunction in terms of a set of potentially arbitrary orthonormal functions, rather than in terms of a set of non-orthonormal and potentially linearly dependent functions, as is the case for standard ML-MCTDH. We show that the EOMs used in the projector splitting integrator (PSI) and the invariant EOM approaches are two special cases of this family obtained from different choices for the dynamic gauge condition, with the invariant EOMs making use of a choice that introduces potentially unbounded operators into the EOMs. As a consequence, all arguments for the existence of parallelizable integration schemes for the invariant EOMs can also be applied to the PSI EOMs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1975

Urban and regional land use analysis: CARETS and census cities experiment package

The author has identified the following significant results. Temperatures in degrees Celsius were derived from PCM counts using the Pease's modified gray window technique. The Outcalt simulator was setup on the USGS computer. The input data to the model are basically meteorological and geographical in nature. The output data is presented in three matrices.

Alexander, R.↗
NASA NTRS1986

Remote sensing of Earth Terrain

The Mueller matrix and polarization covariance matrix for polarimetric radar systems were studied. The clutter is modelled by a layer of random permittivity, described by a three dimensional correlation function, with variance, and horizontal and vertical correlation lengths. This model is applied, using the wave theory with Born approximations carried to the second order, to find the backscattering elements of the polarimetric matrices. It is found that 8 out of 16 elements of the Mueller matrix are identically zero, corresponding to a covariance matrix with four zero elements. Theoretical predictions are matched with experimental data for vegetation fields. A general mixing formula is derived for discrete scatterers immersed in a host medium. The inclusion particles are assumed to be ellipsoidal. The electric field inside the scatterers is determined by quasistatic analysis, assuming the diameter of the inclusion particles to be much smaller than the wavelength. The results are applicable to general multiphase mixtures.

Kong, J. A.↗
NASA NTRS1979

A computer program to generate equations of motion matrices, L217 (EOM). Volume 2: Supplemental system design and maintenance document

The equations of motion program L217 (EOM) is described. The program formulates the matrix coefficients for a second order linear differential equation which describes the motion of an airplane relative to its level equilibrium flight condition. Aerodynamic data from FLEXSTAB or Doublet Lattice (L216) programs are used to derive the equations for quasi-steady or complete unsteady aerodynamics.

Clemmons, R. E.↗
NASA NTRS1993

Constraints on Mueller matrices of polarization optics

The issue of physical realizability constraints on depolarizing scattering or imaging systems is addressed. In particular, the overpolarization problem, i.e., the problem of ensuring that the output degree of polarization is always smaller than (or equal to) unity, is discussed in detail. A set of necessary conditions for the elements of a Mueller matrix is derived. These conditions can be used to test the accuracy of polarimetric measurements and computations. Several recent experimental examples from polarization optics and radar are discussed.

Kostinski, Alexander B.↗
DOE OSTI2024

Tough and circular glass fiber composites via a tailored dynamic boronic ester interface

Glass fiber reinforced polymer (GFRP) composites are valued for their strength and cost-effectiveness. However, traditional GFRPs often face challenges for end-of-life recycling due to their non-depolymerizable thermoset matrices, and long-term performance due to inadequate interfacial adhesion, which can lead to fiber–matrix delamination. Here, in this work, we have designed dynamic fiber–matrix interfaces to allow tough and closed-loop recyclable GFRPs by utilizing a vitrimer, derived from upcycled polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS) with boronic ester (S-Bpin) and amine-based diol crosslinker. The boronic ester groups in S-Bpin form dynamic covalent bonds with the naturally present hydroxyl groups on the unsized GF surface, which eliminates the need for fiber sizing and enables facile closed-loop recyclability of both the fibers and the vitrimer matrix. The resulting strong fiber–matrix interface, depicted by the Raman mapping, leads to a 552% increase in-plane shear toughness (6.2 ± 0.3 MJ m -3 ) and 27% ultimate tensile strength (361 ± 89.2 MPa) compared to those of the conventional epoxy-based matrix (0.95 ± 0.05 MJ m -3 and 264 ± 59.7 MPa, respectively). The network rearrangement through dynamic boronic ester exchange enables fast thermoformability and repairability of micro-cracks at elevated temperatures. Additionally, both the matrix and composite demonstrate strong adhesion to various surfaces including steel and glasses exhibiting ≥6 MPa lap shear strength, which expands their suitability for diverse industrial applications. The readily created dynamic interface between boronic ester functionalized vitrimer and neat GFs presents a promising strategy for developing closed-loop recyclable, multifunctional structural materials, offering a sustainable alternative to non-recyclable thermoset GFRPs and contributes to a circular economy in composite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mixed matrix membranes for post-combustion carbon capture: From materials design to membrane engineering

Mixed matrix materials (MMMs) containing nanofillers dispersed in continuous polymer matrices have emerged as an exciting and versatile platform to develop membranes with superior CO 2 /N 2 separation performance for post-combustion carbon capture. Both polymers and nanofillers can be vertically designed and engineered to combine the advantages of excellent processability (derived from polymers) and strong size-sieving ability or/and significant permanent porosity (originated from nanofillers). However, the MMMs face major challenges, such as interfacial incompatibility, particle agglomeration, and poor thin-film formability. This report provides a comprehensive yet critical review of various polymers and nanofillers (such as metal-organic frameworks, covalent organic frameworks, and two-dimensional materials) with promising CO 2 /N 2 separation properties. We exhaustively describe strategies to improve interfacial compatibility, such as in situ syntheses of polymers and nanofillers and functionalization of both components to improve adhesion. Moreover, we highlight various approaches to engineer the MMMs into thin-film composite (TFC) membranes. The review reveals the structure/property relationship in these MMMs and outlines the challenges and opportunities to realize their potential for practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗