SEARCH · Engineering Papers

Results for “Defects in solids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Development and Implementation of Nationally Recognized Laboratory for Material Characterization in the Microwave and Millimeter Wave Bands

This report provides a progress update for establishing a laboratory for material characterization in the microwave and millimeter wave bands. During the launch of STS-124 a large area of refractory bricks was liberated from the flame trench built for the exhaust of the solid rocket motors (SRM). The inspection of the liberated area revealed many defects, debonds, corrosion and voids that are a cause for concern relating to the health of the entire flame trench wall. A request for assistance was received for the nondestructive evaluation (NDE) of these anomalies behind the refractory bricks, with the primary interest being a health assessment based on the quality of the brick, epoxy and concrete bond.

Hepburn, Frank L.↗

DOE OSTI2022

In Situ Nanoscale Dynamics Imaging in a Proton‐Conducting Solid Oxide for Protonic Ceramic Fuel Cells

Abstract Hydrogen fuel cells and electrolyzers operating below 600 °C, ideally below 400 °C, are essential components in the clean energy transition. Yttrium‐doped barium zirconate BaZr 0.8 Y 0.2 O 3‐d (BZY) has attracted a lot of attention as a proton‐conducting solid oxide for electrochemical devices due to its high chemical stability and proton conductivity in the desired temperature range. Grain interfaces and topological defects modulate bulk proton conductivity and hydration, especially at low temperatures. Therefore, understanding the nanoscale crystal structure dynamics in situ is crucial to achieving high proton transport, material stability, and extending the operating range of proton‐conducting solid oxides. Here, Bragg coherent X‐ray diffractive imaging is applied to investigate in situ and in 3D nanoscale dynamics in BZY during hydration over 40 h at 200 °C, in the low‐temperature range. An unexpected activity of topological defects and subsequent cracking is found on a nanoscale covered by the macroscale stability. The rearrangements in structure correlate with emergent regions of different lattice constants, suggesting heterogeneous hydration. The results highlight the extent and impact of nanoscale processes in proton‐conducting solid oxides, informing future development of low‐temperature protonic ceramic electrochemical cells.

25 ENERGY STORAGE↗

DOE OSTI2024

Melting anisotropy in crystalline solids

Despite the long and extensive history of melting studies, experiments to determine the dependence of melting on crystal orientation are lacking. Using longitudinal sound speed measurements in aluminum single crystals shock compressed along < 100 > and < 110 > to 168 GPa, we address this need and show that the melting transition (both onset and completion) is strongly anisotropic. Furthermore, the present findings demonstrate the need to consider the role of deformation induced lattice defects on the melting transition and provide a general approach to examine melting anisotropy in crystalline solids.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Integrating computation and experiment to investigate photoelectrodes for solar water splitting at the microscopic scale.

CONSPECTUS: Photoelectrochemical water-splitting is a promising and sustainable way to store the energy of the sun in chemical bonds and use it to produce hydrogen gas, a clean fuel. The key components in photoelectrochemical cells (PECs) are photoelectrodes, including a photocathode that reduces water to hydrogen gas and a photoanode that oxidizes water to oxygen gas. Materials used in photoelectrodes for PECs must effectively absorb sunlight, yield photogenerated carriers, and exhibit electronic properties that enable the efficient shuttling of carriers to the surface to participate in relevant water-splitting reactions. Discovering and understanding the key characteristics of optimal photoelectrode materials is paramount to the realization of PEC technologies. Oxide-based photoelectrodes can satisfy many of these materials requirements, including stability in aqueous environments, band edges with reasonable alignment with the redox potentials for water splitting, and ease of synthesis. However, oxide photoelectrodes generally suffer from poor charge transport properties and considerable bulk electron-hole separation, and they have relatively large band gaps. Numerous strategies have been proposed to improve these aspects and understand how these improvements are reflected in the photoelectrochemical performance. Unfortunately, the structural and compositional complexity of multinary oxides accompanied by the inherent complexity of photoelectrochemical processes makes it challenging to understand the individual effects of composition, structure, and defects in the bulk and on the surface on a material's photoelectrochemical properties. The integration of experiment and theory has great potential to increase our atomic-level understanding of structure-composition-property relationships in oxide photoelectrodes. In this Account, we describe how integrating experiment and theory is beneficial for achieving scientific insights at the microscopic scale. We highlight studies focused on understanding the role of (i) bulk composition via solid-state solutions, intercalation, and comparison with isoelectronic compounds, (ii) dopants for both the anion and cation and their interactions with oxygen vacancies, and (iii) surface/interface structure in the photocurrent generation and photoelectrochemical performance in oxide photoelectrodes. In each instance, we outline strategies and considerations for integrating experiment and theory and describe how this integration led to valuable insights and new directions in uncovering structure-composition-property relationships. Our aim is to demonstrate the unique value of combining experiment and theory in studying photoelectrodes and to encourage the continued effort to bring experiment and theory in closer step with each other.

Wang, Wennie↗

DOE OSTI2020

Contrasting SnTe–NaSbTe 2 and SnTe–NaBiTe 2 Thermoelectric Alloys: High Performance Facilitated by Increased Cation Vacancies and Lattice Softening

Defect chemistry is critical to designing high performance thermoelectric materials. In SnTe, the naturally large density of cation vacancies results in excessive hole doping and frustrates the ability to control the thermoelectric properties. Yet, recent work also associates the vacancies with suppressed sound velocities and low lattice thermal conductivity, underscoring the need to understand the interplay between alloying, vacancies, and the transport properties of SnTe. Here, we report solid solutions of SnTe with NaSbTe 2 and NaBiTe 2 (NaSn m SbTe m +2 and NaSn m BiTe m +2 , respectively) and focus on the impact of the ternary alloys on the cation vacancies and thermoelectric properties. We find introduction of NaSbTe 2 , but not NaBiTe 2 , into SnTe nearly doubles the natural concentration of Sn vacancies. Furthermore, DFT calculations suggest that both NaSbTe 2 and NaBiTe 2 facilitate valence band convergence and simultaneously narrow the band gap. These effects improve the power factors but also make the alloys more prone to detrimental bipolar diffusion. Indeed, the performance of NaSn m BiTe m +2 is limited by strong bipolar transport and only exhibits modest maximum ZTs ≈ 0.85 at 900 K. In NaSn m SbTe m +2 however, the doubled vacancy concentration raises the charge carrier density and suppresses bipolar diffusion, resulting in superior power factors than those of the Bi-containing analogues. Lastly, NaSbTe 2 incorporation lowers the sound velocity of SnTe to give glasslike lattice thermal conductivities. Facilitated by the favorable impacts of band convergence, vacancy-augmented hole concentration, and lattice softening, NaSn m SbTe m +2 reaches high ZT ≈ 1.2 at 800–900 K and a competitive average ZT avg of 0.7 over 300–873 K. The difference in ZT between two chemically similar compounds underscores the importance of intrinsic defects in engineering high-performance thermoelectrics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Group-III quantum defects in diamond are stable spin-1 color centers

Color centers in diamond have emerged as leading solid-state “artificial atoms” for a range of quantum technologies, from quantum sensing to quantum networks. Concerted research activities are now underway to identify new color centers that combine stable spin and optical properties of the nitrogen vacancy (NV – ) with the spectral stability of the silicon vacancy (SiV – ) centers in diamond, with recent research identifying other group-IV color centers with superior properties. In this paper, we investigate a class of diamond quantum emitters from first principles, the group-III color centers, which we show to be thermodynamically stable in a spin-1, electric-field-insensitive structure. Further, from ab initio electronic structure methods, we characterize the product Jahn-Teller (pJT) effect present in the excited-state manifold of these group-III color centers, where we capture symmetry-breaking distortions associated with strong electron-phonon coupling. These predictions can guide experimental identification of group-III vacancy centers and their use in applications in quantum information science and technology.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Ferroelectric Large Polarons and Defect Tolerance in Multi-Component Lead Halide Perovskites

Solvation plays a pivotal role in chemistry and biology. A solid-state analogy of solvation is polaron formation, but the magnitude of Coulomb screening is typically an order-of-magnitude weaker than that of solvation in aqueous solutions. Here the PI aims to explore a new class of polarons, the ferroelectric large polaron, which allows efficient Coulomb screening of an electron or hole by extended ordering of dipoles from symmetry-broken unit cells. This kind of local ordering is reflected in the ferroelectric-like THz dielectric responses of lead halide perovskites (LHPs) and may be partially responsible for their exceptional optoelectronic performances. A charge carrier may be localized to and/or induce the formation of nanoscale domain boundaries of locally ordered dipoles in a ferroelectric or paraelectric material, i.e., crystal structure with polar unit cells or polar fluctuations. The ability to form ferroelectric large polarons can result in the efficient screening of charge carriers from scattering with other charge carriers, with charged defects, and with longitudinal optical phonons, thus contributing to enhanced optoelectronic properties. During the past funding period, the PI has explored efficient charge carrier screening in three-dimensional (3D) LHP crystals and has developed the ferroelectric large polaron model to explain a range of carrier properties in these materials. The PI has also developed a new experimental tool, two-dimensional optical Kerr effect (2D-OKE), which is particularly powerful in probing photophysical properties with exquisite energy resolution at or near the bandgap. During the next funding periods, the PI aims to establish the applicability of the ferroelectric large polaron proposal as a general principle for the design/search of defect tolerant semiconductors in optoelectronics. Preliminary experiments on model semiconductor systems beyond LHPs have demonstrated the feasibility of the proposed research.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials (Second Annual Progress Report)

Additive manufacturing (AM) is an emerging method for cost-efficient fabrication of nuclear reactor parts. AM of metallic structures for nuclear energy applications is currently based on laser powder bed fusion (LPBF) process, which can introduce internal material flaws, such as pores and anisotropy. Integrity of AM structures needs to be evaluated nondestructively because material flaws could lead to premature failures due to exposure to high temperature, radiation and corrosive environment in a nuclear reactor. Thermal tomography (TT) provides a capability for non-destructive evaluation of sub-surface defects in arbitrary size structures. Thermal tomography is a computational method for heat diffusion-based imaging of solids, which provides 3D visualization of data from flash thermography measurements. We investigate thermal tomography imaging and nondestructive evaluation of stainless steel and nickel super alloy metallic structures produced with laser powder bed fusion (LPBF) additive manufacturing (AM) process. Metallic structures produced with LPBF contain defects, and there are limited capabilities to evaluate these structures non-destructively. Thermal tomography reconstruction of 3D apparent spatial effusivity provides information about AM structure geometry and internal material flaws. We study performance of thermal tomography in imaging of metallic structures through COMSOL computer simulations of transient heat transfer, and through reconstruction of data obtained from experimental measurements. Reconstruction of internal defects is investigated using a stainless steel 316L specimen with flat bottom hole (FBH) indentations, and Inconel 718 plate produced with laser powder bed fusion (LPBF) method, which contains imprinted hemispherical shape low density regions containing non-sintered metallic powder. The FBH’s have the same sizes as the imprinted defects in the LPBF specimens, but offer better imaging contrast. Thermal tomography reconstructions provide visualizations of internal defects, and allow for estimation of their sizes and locations. Detection sensitivity of TT is limited by noises. We investigate separation of signal from noise in thermography images using several machine learning (ML) methods, including new spatio-temporal blind source separation (STBSS) and spatio-temporal sparse dictionary learning (STSDL) methods. Performance of the ML methods is benchmarked using thermography data obtained from imaging stainless steel 316L and Inconel 718 specimens produced LPBF method with imprinted calibrated porosity defects. The ML methods are ranked by F-score and execution runtime. Finally, we investigate TT of AM stainless steel 316L specimen with imprinted internal porosity defects using relatively low-cost, small form factor infrared (IR) camera based on uncooled micro bolometer detector. Sparse coding related K-means singular value decomposition (SVD) machine learning, image processing algorithms are developed to improve quality of TT images through removal of Additive white Gaussian noise without blurring the images. Following initial qualification of an AM component for deployment in a nuclear reactor, a compact TT can also be used for in-service nondestructive evaluation (NDE). With capability to perform in-service NDE of the AM component lifecycle, TT data can be used for development of a component digital twin.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2026

First-principles thermodynamic assessment of Sr-containing secondary phase formation in strontium-substituted lanthanum manganites for solid oxide cell applications

Sr-secondary phase formation is a potentially significant degradation mode with direct impact upon solid-oxide cell (SOC) commercial viability. A first-principles based thermodynamic study was performed for La 1−x Sr x MnO 3±δ (LSM) perovskites to assess their stability against formation of different Sr-secondary phases, including SrO, SrCrO 4 , SrSO 4 , SrCO 3 , and Sr(OH) 2 , for SOC applications. The Sr-secondary phase formation reaction free energies were determined via a thermodynamic model by combining ab initio lattice dynamics calculations for the solid phases and ab initio thermodynamic data for the gas phases. The current approach expands the previously reported thermodynamic modeling studies by integrating first-principles based point defect equilibria into the thermodynamic analysis. The modeling results obtained using this new approach indicate an increased tendency to form the SrO oxide upon decreasing the oxygen partial pressure. Additionally, the enhancing factors to form the Sr-related secondary phase from the associated SrO activity in LSM are further quantified by considering the equilibrium of SrO reacting with the contaminant gas species as a function of temperature and pressure.

defect thermodynamics modeling↗

DOE OSTI2023

Assessing the quality of large-area monolayer graphene grown on liquid copper for size-selective ionic/molecular membrane separations

Monolayer graphene growth on liquid copper (Cu) has attracted attention due to advantages of a flat/smooth catalytic growth surface, high synthesis temperature (>1080 °C) as well as the possibility of forming graphene domains that are mobile on the liquid Cu with potential to minimize grain boundary defects and self-assemble into a continuous monolayer film. However, the quality of monolayer graphene grown on liquid copper and its suitability for size-selective ionic/molecular membrane separations has not been evaluated/studied. Here, we probe the quality of monolayer graphene grown on liquid Cu (via a metallurgical process, HSMG ® ) using Scanning Electron Microscope (SEM), High-resolution transmission electron microscope (HR-TEM), Raman spectroscopy and report on a facile approach to assess intrinsic sub-nanometer to nanometer-scale defects over centimeter-scale areas. We demonstrate high transfer yields of monolayer graphene (>93% coverage) from the growth substrate to polyimide track etched membrane (PITEM, pore diameter ~200 nm) supports to form centimeter-scale atomically thin membranes. Next, we use pressure-driven transport of ethanol to probe defects > 60 nm and diffusion-driven transport of analytes (KCl ~0.66 nm, L-Tryptophan ~0.7–0.9 nm, Vitamin B12 ~1–1.5 nm and Lysozyme ~3.8–4 nm) to probe nanoscale and sub-nanometer scale defects. Diffusive transport confirms the presence of intrinsic sub-nanometer to nanometer scale defects in monolayer graphene grown on liquid Cu are no less than that in high-quality graphene synthesized via chemical vapor deposition (CVD) on solid Cu. Our work not only benchmarks quality of graphene grown on liquid copper for membrane applications but also provides fundamental insights into the origin of intrinsic defects in large-area graphene synthesized via bottom-up processes for membrane applications.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Assessment of critical flaw sizes and crack driving forces during additive manufacturing of metallic materials

Additive manufacturing (AM) of complex engineering components is often plagued by a high susceptibility to cracking, particularly in high-strength metallic materials. While alloy design efforts have made progress in mitigating solidification defects, there remains a need for mechanistic guidelines to predict susceptibility to solid-state cracking. To address this gap, driving forces for the growth of melt pool cracks are calculated across a wide range of alloys using an efficient computational framework. Calculations are coupled with rapid single track laser experiments to elucidate trends in cracking from laser melting. The analyses conducted here highlight the important role of material properties in susceptibility to cracking, notably fracture toughness and elastic modulus. An important finding is that residual stresses that are limited in magnitude to the yield stress of the material are likely insufficient to drive cracking during cooling. Furthermore, the implications of these results are discussed in the context of alloy design for AM and residual stress accumulation during AM.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Disorder trapping and formation of antiphase nanodomains in Ni 3 Sn: in situ observation and high resolution characterization

Rapid solidification of the intermetallic Ni 3 Sn compound from an undercooled liquid was investigated using time-resolved synchrotron X-ray diffraction. Primary growth of an ordered and a disordered cubic solid was observed in situ at a low and a high undercooling, respectively. The disordered cubic solid was reordered after rapid solidification and experienced a solid-state transformation in cooling. A HRTEM study revealed high density of crystal defects and nanodomains in the transformed matrix. A HAADFSTEM study determined that the nanodomains are antiphase domains with chemical disorder. These observations indicated a possibility of online control of mechanical properties in additively manufactured intermetallics.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Spin Emitters beyond the Point Dipole Approximation in Nanomagnonic Cavities

Control over transition rates between spin states of emitters is crucial in a wide variety of fields ranging from quantum information science to the nanochemistry of free radicals. We present an approach to drive both electric and magnetic dipole-forbidden transitions of a spin emitter by placing it in a nanomagnonic cavity, requiring a description of both the spin emitter beyond the point dipole approximation and the vacuum magnetic fields of the nanomagnonic cavity with a large spatial gradient over the volume of the spin emitter. We specifically study the silicon vacancy (SiV – ) defect in diamond, whose Zeemansplit ground states comprise a logical qubit for solid-state quantum information processing, coupled to a magnetic nanoparticle serving as a model nanomagnonic cavity capable of concentrating microwave magnetic fields into deeply subwavelength volumes. Through first-principles modeling of the SiV – spin orbitals, we calculate the spin transition densities of magnetic dipole-allowed and -forbidden transitions and calculate their coupling rates to various multipolar modes of the nanomagnonic cavity. We envision using such a framework for manipulation of quantum spin states.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Engineering Surface Oxygenated Functionalities on Commercial Carbon toward Ultrafast Sodium Storage in Ether-Based Electrolytes

The pursuit of a high-capacity anode material has been urgently required for commercializing sodium-ion batteries with a high energy density and an improved working safety. In the absence of thermodynamically stable sodium intercalated compounds with graphite, constructing nanostructures with expanded interlayer distances is still the mainstream option for developing high-performance carbonaceous anodes. In this regard, a surface-functionalized and pore-forming strategy through a facile CO 2 thermal etching route was rationally adopted to engineer negligible oxygenated functionalities on commercial carbon for boosting the sodium storage process. Benefitted from the abundant ionic/electronic pathways and more active reaction sites in the microporous structure with noticeable pseudocapacitive behaviors, the functionalized porous carbon could achieve a highly reversible capacity of 505 mA h g -1 at 50 mA g -1 , an excellent rate performance of 181 mA h g -1 at 16,000 mA g -1 , and an exceptional rate cycle stability of 176 mA h g -1 at 3200 mA g -1 over 1000 cycles. These outstanding electrochemical properties should be ascribed to a synergistic mechanism, fully utilizing the graphitic and amorphous structures for synchronous intercalations of sodium ions and solvated sodium ion compounds, respectively. Finally, the controllable generation and evolution of a robust but thin solid electrolyte interphase film with the emergence of obvious capacitive reactions on the defective surface, favoring the rapid migration of sodium ions and solvated species, also contribute to a remarkable electrochemical performance of this porous carbon black.

25 ENERGY STORAGE↗

NASA NTRS1975

Precipitation of silicon from splat-cooled Al-Si alloys

Splat cooled Al-Si solid solutions with 1 to 11 at.% Si were prepared and their precipitation kinetics were studied by transmission electron microscopy. The time required for appearance of particles visible at a magnification of 35,000 times was determined at temperatures between 248 K and 573 K. The resulting Arrhenius plots yielded activation energies ranging from 55 to 40 plus or minus 2kJ/mol over the composition range. Precipitate densities were higher and denuded zones of 100 to 150 nm were narrower than in comparable solid quenched samples. The activation energies are explained in terms of excess point defect concentrations.

Matyja, H.↗

DOE OSTI2020

Single-atom-layer traps in a solid electrolyte for lithium batteries

In order to fully understand the lithium-ion transport mechanism in solid electrolytes for batteries, not only the periodic lattice but also the non-periodic features that disrupt the ideal periodicity must be comprehensively studied. At present only a limited number of non-periodic features such as point defects and grain boundaries are considered in mechanistic studies. Here, we discover an additional type of non-periodic feature that significantly influences ionic transport; this feature is termed a “single-atom-layer trap” (SALT). In a prototype solid electrolyte Li 0.33 La 0.56 TiO 3 , the single-atom-layer defects that form closed loops, i.e., SALTs, are found ubiquitous by atomic-resolution electron microscopy. According to ab initio calculations, these defect loops prevent large volumes of materials from participating in ionic transport, and thus severely degrade the total conductivity. This discovery points out the urgency of thoroughly investigating different types of non-periodic features, and motivates similar studies for other solid electrolytes.

25 ENERGY STORAGE↗

NASA NTRS1999

Gravitational Effects on the Morphology and Kinetics of Photodeposition of Polydiacetylene Thin Films From Monomer Solutions

The goal of this proposed work is to study gravitational effects on the photodeposition of polydiacetylene thin films from monomer solutions onto transparent substrates. Polydiacetylenes have been an extensively studied class of organic polymers because they exhibit many unusual and interesting properties, including electrical conductivity and optical nonlinearity. Their long polymeric chains render polydiacetylenes readily conducive to thin film formation, which is necessary for many applications. These applications require thin polydiacetylene films possessing uniform thicknesses, high purity, minimal inhomogeneities and defects (such as scattering centers), etc. Also, understanding and controlling the microstructure and morphology of the films is important for optimizing their electronic and optical properties. The lack of techniques for processing polydiacetylenes into such films has been the primary limitation to their commercial use. We have recently discovered a novel method for the formation of polydiacetylene thin films using photo-deposition from monomer solutions onto transparent substrates with UV light. This technique is very simple to carry out, and can yield films with superior quality to those produced by conventional methods. Furthermore, these films exhibit good third-order properties and are capable of waveguiding. We have been actively studying the chemistry of diacetylene polymerization in solution and the photo-deposition of polydiacetylene thin films from solution. It is well-known that gravitational factors such as buoyancy-driven convection and sedimentation can affect chemical and mass transport processes in solution. One important aspect of polydiacetylene thin film photodeposition in solution, relevant to microgravity science, is that heat generated by absorption of UV radiation induces thermal density gradients that under the influence of gravity, can cause fluid flows (buoyancy-driven convection). Additionally, changes in the chemical composition of the solution during polymerization may cause solutal convection. These fluid flows affect transport of material to and from the film surface and thereby affect the kinetics of the growth process. This manifests itself in the morphology of the resulting films; films grown under the influence of convection tend to have less uniform thicknesses, and can possess greater inhomogeneities and defects. Specifically, polydiacetylene films photodeposited from solution, when viewed under a microscope, exhibit very small particles of solid polymer which get transported by convection from the bulk solution to the surface of the growing film and become embedded. Even when carried out under conditions designed to minimize unstable density gradients (i.e., irradiating the solution from the top), some fluid flow still takes place (particles remain present in the films). It is also possible that defect nucleation may be occurring within the films or on the surface of the substrate; this, too, can be affected by convection (as is the case with crystal growth). Hence films grown in 1-g will, at best, still possess some defects. The objective of this proposal is to investigate, both in 1-g and in low-g, the effects of gravitational factors (primarily convection) on the dynamics of these processes, and on the quality, morphology, and properties of the films obtained.

Paley, Mark S.↗

DOE OSTI2023

Tailoring the Angular Mismatch in MoS 2 Homobilayers through Deformation Fields

Ultrathin MoS 2 has shown remarkable characteristics at the atomic scale with an immutable disorder to weak external stimuli. Ion beam modification unlocks the potential to selectively tune the size, concentration, and morphology of defects produced at the site of impact in 2D materials. Combining experiments, first-principles calculations, atomistic simulations, and transfer learning, it is shown that irradiation-induced defects can induce a rotation-dependent moiré pattern in vertically stacked homobilayers of MoS 2 by deforming the atomically thin material and exciting surface acoustic waves (SAWs). Furthermore, the direct correlation between stress and lattice disorder by probing the intrinsic defects and atomic environments are demonstrated. The method introduced in this paper sheds light on how engineering defects in the lattice can be used to tailor the angular mismatch in van der Waals (vdW) solids.

2D materials↗