SEARCH · Engineering Papers

Results for “Current measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Demonstrating the β-Ga 2 O 3 Schottky diodes for alpha radiation detection

Schottky barrier diodes were fabricated on (001) monoclinic β-Ga 2 O 3 wafers with low doped epitaxial layers of 7.0 × 10 15 cm −3 . Circular Ni Schottky contacts with area 2 mm 2 were deposited by electron beam evaporation. Devices were characterized electrically by performing forward and reverse current-voltage sweeps with a range of −100 V–2 V, as well as capacitance-voltage sweeps to −30 V. The breakdown voltage was also determined to be −180 V for the devices. Experiments measuring the electrical response from incident X-ray radiation was performed. A response time to X-ray radiation of less than 1 s was recorded and a decay time of approximately 2 s after removing X-ray source, which primarily attribute to X-ray switching on and off time. Energy spectra of alpha particles from a 0.9 μCi 241 Am button source was collected at various voltage biases using devices with the lowest measured leakage current while reverse biased. The total count rate was observed to increase linearly with increasing device bias. In conclusion, the peak channel number was observed to increase with increasing bias with the best resolution of 9.5% at −100 V reverse bias.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2023

Applying Bayesian inference and deterministic anisotropy to retrieve the molecular structure ∣Ψ(R)∣2 distribution from gas-phase diffraction experiments

Abstract Currently, our general approach to retrieving molecular structures from ultrafast gas-phase diffraction heavily relies on complex ab initio electronic or vibrational excited state simulations to make conclusive interpretations. Without such simulations, inverting this measurement for the structural probability distribution is typically intractable. This creates a so-called inverse problem. Here we address this inverse problem by developing a broadly applicable method that approximates the molecular frame structure ∣Ψ( R , t )∣ 2 distribution independent of these complex simulations. We retrieve the vibronic ground state ∣Ψ( R )∣ 2 for both simulated stretched NO 2 and measured N 2 O. From measured N 2 O, we observe 40 mÅ coordinate-space resolution from 3.75 Å −1 reciprocal space range and poor signal-to-noise, a 50X improvement over traditional Fourier transform methods. In simulated NO 2 diffraction experiments, typical to high signal-to-noise levels predict 100–1000X resolution improvements, down to 0.1 mÅ. By directly measuring the width of ∣Ψ( R )∣ 2 , we open ultrafast gas-phase diffraction capabilities to measurements beyond current analysis approaches. This method has the potential to effectively turn gas-phase ultrafast diffraction into a discovery-oriented technique to probe systems that are prohibitively difficult to simulate.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2024

Design of a low frequency, density profile reflectometer system for the MAST-U spherical tokamak

Validated and accurate edge profiles (temperature, density, etc.) are vitally important to the Mega Ampere Spherical Tokamak Upgrade (MAST-U) divertor and confinement effort. Density profile reflectometry has the potential to significantly add to the measurement capabilities currently available on MAST-U (e.g., Thomson scattering and Langmuir probes). This work presents the diagnostic requirements, problems, and solutions facing profile reflectometry in spherical tokamaks and MAST-U in particular. Requirements include density measurements near zero electron density in the scrape off layer region, coverage for a broad range of MAST-U plasma parameters, high time (≤10 microseconds) and spatial resolutions (≤1 cm), reliability, and identification of the plasma start frequency.

Instruments & Instrumentation↗

DOE OSTI2021

Measuring Electron Diffusion and Constraining the Neutral Current $\pi^0$ Background for Single-Photon Events in MicroBooNE

Liquid Argon Time Projection Chambers (LArTPCs) are a rising technology in the field of experimental neutrino physics. LArTPCs use ionization electrons and scintillation light to reconstruct neutrino interactions with exceptional calorimetric and position resolution capabilities. Here, I present two analyses conducted in the MicroBooNE LArTPC at Fermilab: a measurement of the longitudinal electron diffusion coefficient, $D_L$, in the MicroBooNE detector and a constraint of the systematic uncertainty on MicroBooNE's single-photon analysis due to the dominant neutral current (NC) \piz{} background. Longitudinal electron diffusion modifies the spatial and timing resolution of the detector, and measuring it will help correct for these effects. Furthermore, current measurements of $D_L$ in liquid argon are sparse and in tension with one another, making the MicroBooNE measurement especially valuable. We report a measurement of $3.74^{+0.28}_{-0.29}$ cm$^2$/s. MicroBooNE is searchin g for si ngle-photon events as a potential explanation for the MiniBooNE low-energy excess (LEE) of electron neutrino-like events, which has been interpreted as evidence for low-mass sterile neutrinos. However, this search is overwhelmed by a large NC \piz{} background. By performing a sideband selection of NC \piz{} events, we apply a data-driven rate constraint to the single-photon analysis to reduce the systematic uncertainties. At present, this constraint improves the single-photon analysis' median sensitivity to the LEE-like signal from 0.9$\sigma$ to $1.5\sigma$. This sensitivity is expected to improve significantly as more data become available. Both of these measurements will not only benefit MicroBooNE, but also inform future LArTPC experiments.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2024

Reference Site Conditions for Floating Wind Arrays in the United States

17 WIND ENERGY↗

DOE OSTI2023

Comparison of Zirconium Redistribution in BISON EBR-II Models Using FIPD and IMIS Databases with Experimental Post Irradiation Examination

Metallic fuels have seen increased interest for future sodium fast reactors due to their material properties: high thermal conductivities and advantageous neutronic properties allow for greater fission densities. One drawback to typical metallic fuels is zirconium redistribution, which impacts this advantageous material and its neutronic properties. Unfortunately, the processes behind zirconium migration behavior are understood using first principles, so before these fuels are implemented in future fast reactors, characterization and fuel qualification regimes must be completed. These activities can be supported through the use of robust modeling using the most accurate empirical models currently available to fuel researchers around the world. The tool that allows researchers to model this complex coupled thermo-mechanical behavior and nuclear properties is BISON. Additionally, BISON model parameters need to be compared against PIE measurements. The current work utilizes two fuel pins from EBR-II experiment X441 to optimize various model parameters, including porosity correction factor, thermal conductivity, phase transition temperature, and diffusion coefficient multipliers, before implementing the final model for seven fuel pins with differing characteristics. To properly evaluate the BISON simulations, the results are compared to PIE metallography data for each fuel pin, to ensure the zirconium redistribution is properly reflected in the simulation results. Six out of seven analyzed fuel pins demonstrate good agreement between the metallography images and BISON results, showing alignment of the Zr-rich, Zr-depleted, and moderately Zr-enriched zones at various axial heights along the fuel pins. Further work is needed to refine the model parameters for general pin use.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Reference Site Condition Datasets for Floating Wind Arrays in the United States

Floating offshore wind farm design is highly site-specific, requiring detailed information about the specific conditions of a project area for realistic design studies. Unfortunately, publicly available site condition data for potential floating offshore wind project sites in the United States is scarce. To support U.S. offshore wind research, we developed reference site condition datasets, including metocean and seabed information, for four potential floating wind project areas in the U.S.: Humboldt Bay, Morro Bay, the Gulf of Maine, and the Gulf of Mexico. These datasets were compiled using publicly available data. Our metocean analysis, covering wind, waves, and surface currents, utilized measurement data from 2000 to 2020. Sources included the National Renewable Energy Laboratory’s National Offshore Wind Dataset for wind data, National Data Buoy Center buoys for wave data, and the High Frequency Radar Network for surface currents. These data were integrated into hourly time series used to compute extreme return periods up to 500 years, monthly statistics, and joint probability clusters for fatigue analysis. Soil conditions were evaluated using the usSEABED database and bathymetry grids were interpolated from the NCEI Digital Elevation Model Global Mosaic. Further information on the datasets and how they were created can be found in: Biglu, M., M. Hall, E. Lozon, S. Housner. 2024. Reference Site Conditions for Floating Wind Arrays in the United States. Golden, CO: National Renewable Energy Laboratory (NREL). NREL/TP-5000-89897. The data are also available at: https://github.com/FloatingArrayDesign/SiteConditions The content of each dataset is as follows: _NOW23_wind.txt: Hourly NOW-23 wind data up to a height of 400 meter. _metocean_1hr.txt: Hourly time series including wind, wave, surface current and temperature data. _Summary.xlsx: Metocean data, including extreme values, joint probability distributions and monthly statistics. _usSEABED_soil.csv: Extract of the usSEABED database for this specific site. _bathymetry_200m.txt (and 500m, 1000m): Gridded seabed depth data.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Mechanism of enhanced critical fields and critical current densities of MgB2 wires with C/Dy$^{2}$O3 co-additions

A series of monofilamentary powder-in-tube MgB2 wires were fabricated with 2 mol. % C doping and co-additions of 0–3 wt. % Dy2O3. Irreversibility fields (μ0Hirr), upper critical fields (μ0Hc2), and transport critical currents were measured, and from these quantities, anisotropies (γ) and electronic diffusivities (Dπ,σ) were estimated. The addition of 1 wt. % Dy2O3 to already optimally C-doped MgB2 wires produced higher Hc2//ab, Hc2//c, and Hirr values at 4.2 K. In addition, the critical current density, Jc, increased with Dy2O3 concentration up to 1 wt. % where non-barrier Jc reached 4.35 × 104 A/cm2 at 4.2 K, 10 T. At higher temperatures, for example, 20 K and 5 T, co-additions of 2 mol. % C and 2 wt. % Dy2O3 improved non-barrier Jc by 40% and 93% compared to 2 and 3 mol. % C doping, respectively. On the other hand, measurements of Tc showed that C/Dy2O3 co-additions increase interband scattering rates at a lower rate than C doping does (assuming C doping levels giving similar levels of low-T μ0Hc2 increase as co-addition). Comparisons to a two-band model for μ0Hc2 in MgB2 allowed us to conclude that the increases in Hc2//ab, Hc2//c, and Hirr (as well as concomitant increases in high-field Jc) with Dy2O3 addition are consistent with increases primarily in intraband scattering. This suggests C/Dy2O3 co-addition to be a more promising candidate for improving non-barrier Jc of MgB2 at temperatures above 20 K.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Room temperature depinning of the charge-density waves in quasi-two-dimensional 1T-TaS 2 devices

Here we report on the depinning of nearly commensurate charge-density waves in 1T-TaS 2 thin films at room temperature. A combination of the differential current–voltage measurements with the low-frequency noise spectroscopy provides unambiguous means for detecting the depinning threshold field in quasi-2D materials. The depinning process in 1T-TaS 2 is not accompanied by an observable abrupt increase in electric current—in striking contrast to depinning in the conventional charge-density-wave materials with quasi-1D crystal structure. We explained it by the fact that the current density from the charge-density waves in the 1T-TaS 2 devices is orders of magnitude smaller than the current density of the free carriers available in the discommensuration network surrounding the commensurate charge-density wave islands. The depinning fields in 1T-TaS 2 thin-film devices are several orders of magnitude larger than those in quasi-1D van der Waals materials. Obtained results are important for the proposed applications of the charge-density wave devices in electronics.

2D materials↗

DOE OSTI2022

Space-based Measurements of Neutron Lifetime: A Novel Approach to a Long-standing Problem

Free neutrons decay via the weak interaction with a mean lifetime of around 15 minutes. Knowledge of this lifetime is important as it provides constraints on the unitarity of the CKM matrix and is a key parameter for studies of Big-Bang nucleosynthesis. However, current laboratory measurements differ by as much as 5σ. We are investigating a new technique to measure neutron lifetime: space-based neutron spectroscopy. We will complete a proof-of-principle demonstration using data from NASA’s MESSENGER mission to Mercury.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Absolute measurement of vacuum ultraviolet photon flux in an inductively coupled plasma using a Au thin film

A new method for absolute measurement of the vacuum ultraviolet (VUV) photon flux at the edge of a plasma is described. The light produced by the plasma was allowed to strike a negatively biased, gold-coated copper substrate remote from the plasma. The resulting photoelectron emission current was measured, and the absolute photon flux was then found from the known photoelectron yield of Au. The method was used to quantify the amount of VUV light produced by an Ar/He inductively coupled plasma (ICP). Strong emissions at 104.82 and 106.67 nm, corresponding to the 1s 2 and 1s 4 resonant states of Ar, were observed. The maximum, integrated VUV photon flux measured at the remote location was 3.2 × 10 13 photons/cm 2 s. This was estimated to correspond to a flux of 5 × 10 15 photons/cm 2 s at the edge of the ICP, in the range of reported values under similar conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Fault Detection Utilizing Convolution Neural Network on Timeseries Synchrophasor Data From Phasor Measurement Units

An end-to-end supervised learning method is proposed for fault detection in the electric grid using Big Data from multiple Phasor Measurement Units (PMUs). The approach consists of preprocessing steps aimed at reducing data noise and dimensionality, followed by utilization of six classification models considered for detecting faults. Three of the models were variants of Convolutional Neural Network (CNN) architectures that consider a single type of measurement (voltage, current or frequency) at all PMUs or all types together also at all PMUs. CNN based models were compared to traditional methods of Logistic Regression (LR), Multi-layer Perceptron (MLP) and Support Vector Machine (SVM). Evaluation was conducted on two-year data measured by PMUs at 37 locations in a large electric grid. Here, the response variable for classification were extracted from the grid-wide outage event log. Experiments show that CNN-based models outperformed traditional methods on one year out-of-sample outage detection over the entire grid.

42 ENGINEERING↗

DOE OSTI2026

Identification of Final-State Neutrons in ANNIE

The Accelerator Neutrino Neutron Interaction Experiment (ANNIE) is a 26-ton gadolinium-loaded (Gd-loaded) water Cherenkov detector located on the Booster Neutrino beamline at Fermilab. ANNIE's primary physics objectives include measuring neutron multiplicity for neutrino-nucleus interactions and performing cross-section measurements of charge current quasi-elastic and neutral current quasi-elastic processes. These measurements aim to improve neutrino energy reconstruction and reduce uncertainties in current and future neutrino oscillation experiments. Additionally, ANNIE serves as a testbed for advanced technologies such as Large Area Picosecond Photodetectors (LAPPDs) and Water-Based Liquid Scintillator, which enhance vertex resolution and enable detection below the Cherenkov threshold. By leveraging the high neutron capture cross section of Gd-loaded water, ANNIE is well positioned to observe final-state neutrons in beam-correlated neutrino interactions. To constrain the uncertainties in the neutron capture efficiency and time within the detector, we have conducted multiple calibration campaigns using an AmBe source. The AmBe source is deployed at different locations of the tank to map the neutron capture efficiency and determine the expected neutron capture time. Additionally, the AmBe calibration data are used to define the precise neutron clustering that will be useful for identifying neutron-like clusters from neutrino interaction. In this poster, we will present the current status of the AmBe neutron calibration program and the development of neutron cluster definition for the ANNIE Experiment.

Ajana, Dhavalkumar [Florida State U.]↗

DOE OSTI2022

Topography inversion in scanning tunneling microscopy of single-atom-thick materials from penetrating substrate states

Scanning tunneling microscopy (STM) is one of the indispensable tools to characterize surface structures, but the distinction between atomic geometry and electronic effects based on the measured tunneling current is not always straightforward. In particular, for single-atomic-thick materials (graphene or boron nitride) on metallic substrates, counterintuitive phenomena such as a larger tunneling current for insulators than for metal and a topography opposite to the atomic geometry are reported. Using first-principles density functional theory calculations combined with analytical modeling, we reveal the critical role of penetrating states of metallic substrates that surpass 2D material states, hindering the measurement of intrinsic 2D materials states and leading to topography inversion. Our finding should be instrumental in the interpretation of STM topographies of atomic-thick materials and in the development of 2D material for (opto)electronic and various quantum applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2026

Weather Data from BSEC Weather Stations

This dataset provides measurements of temperature, humidity, rainfall, wind, and sunlight at Ambient Weather and OttHydro stations across Baltimore city. These surface weather stations were deployed by the Baltimore Social-Environmental Collaborative (BSEC) Urban Integrated Field Laboratory (UIFL) project, funded by the Department of Energy (DOE). This dataset currently contains measurements from 2023 to June 2026 and will be periodically updated to include more stations and recent observations when available. Data File Information This dataset contains surface weather measurements data in comma-separated value (CSV) format and documents that describe the weather stations, locations, and measured parameters and units. data/[TIMEAVG]/[YEAR]/BSEC-[STATIONID]_[SENSORTYPE]_[TIMEAVG]_[YEAR].csv Surface weather measurements data in CSV format, where STATIONID indicates the weather station, SENSORTYPE is the type of weather station ('AWS' = Ambient Weather Station and 'OTT' = 'OttHydro Station'), TIMEAVG is time period for each entry (= daily, hourly, or 5min), and YEAR indicate the year in which the measurements were made. Example data file name: BSEC-AAC_AWS_hourly_2023.csv. documents/Station_Locations.csv This CSV file provides location information and measurement start date for each surface weather station. documents/Weather_Station_Descriptions.pdf This document provides detailed description of the instruments along with their setup and accuracy of measurement. documents/File_Contents.pdf This document describes the contents on the data files, including time notation, weather parameters and units of measurement. documents/site-metadata/[STATOINID]-metadata.pdf These PDF files provide information on weather station sites, including land cover characteristics, station mounting, and photographs. Each PDF file corresponds to one station, as indicated by STATIONID.

Ambient Weather Stations↗

DOE OSTI2020

Specifying Calibration of Energy-Measuring Equipment

Instruments and standards need to be calibrated periodically to ensure that their use yields accurate measurements. Calibration needs, however, vary in sophistication, based on user expectations. This white paper reviews calibration terminology and standards, and describes best practices that have been developed for a) calibrating measurement equipment to ensure some known level of accuracy, and b) accrediting calibration service providers. Calibration is discussed in the context of metrological traceability, and excerpts from laboratory scopes of accreditation are shared to reveal the diversity of terminology and format among them. In an effort to aid those who currently calibrate measuring equipment or who have new or changing needs for calibrating measuring equipment, rationale is provided for why a specification might be used to request calibration services that meet specific test needs. Given the growing interest in using data to manage the energy consumption of systems, and the increasing number and variety of systems (e.g., building, computing) that can report such information, use cases requiring energy data are used to facilitate further discussion and provide examples. Commercially available service providers who are accredited for energy-measuring equipment calibration are compared and contrasted, and a specification template that might be used for requesting this calibration is presented. The specification template should be tailored to meet each user’s needs. To illustrate, an example set of energy-measuring-equipment test conditions (reflecting the planned usage of the device to be calibrated) is used to develop a customized calibration specification, and commercially available service providers are assessed in terms of their qualifications for calibration to that particular implementation of the specification template.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Biochemical Conversion of Lignocellulosic Biomass to Hydrocarbon Fuels and Products: 2020 State of Technology and Future Research

The annual State of Technology (SOT) assessment is an essential activity for biochemical platform research. It allows the impact of research progress to be quantified in terms of economic improvements in the overall cellulosic biofuel production process for a particular conversion pathway. As such, initial benchmarks can be established for currently demonstrated performance and progress can be tracked towards out-year goals to ultimately demonstrate cost-competitive cellulosic biofuel technology. The purpose of this report is to benchmark the latest experimental developments across a number of potential bioconversion pathways as quantified by modeled minimum fuel selling prices (MFSPs), as a measure of current status relative to those final targets. For this state of technology, TEA models were run for two separate biological conversion pathways to fuels, based on available data for integrated biomass deconstruction and hydrolysate processing; namely carboxylic acids (primarily butyric acid) and diols (2,3-butanediol [BDO]), reflecting NREL's recently-published 2018 biochemical design report focused on those two pathways. The models were run across three scenarios for lignin utilization, namely combustion, conversion to coproducts based on "base case" performance with biomass hydrolysate, and conversion to coproducts based on "high" performance demonstrated with model lignin monomer components. Relative to prior 2019 benchmarks, the 2020 SOT achieved further MFSP reductions of approximately $1/gallon gasoline equivalent, primarily attributed to improvements in pretreatment that led to both cost reductions and yield improvements.

09 BIOMASS FUELS↗

DOE OSTI2022

Biochemical Conversion of Lignocellulosic Biomass to Hydrocarbon Fuels and Products (2021 State of Technology and Future Research)

The annual State of Technology (SOT) assessment is an essential activity for biochemical platform research. It allows the impact of research progress to be quantified in terms of economic improvements in the overall cellulosic biofuel production process for a particular conversion pathway. As such, initial benchmarks can be established for currently demonstrated performance and progress can be tracked towards out-year goals to ultimately demonstrate cost-competitive cellulosic biofuel technology. The purpose of this report is to benchmark the latest experimental developments across a number of potential bioconversion pathways as quantified by modeled minimum fuel selling prices (MFSPs), as a measure of current status relative to those final targets. For this state of technology, TEA models were run for two separate biological conversion pathways to fuels, based on available data for integrated biomass deconstruction and hydrolysate processing; namely carboxylic acids (primarily butyric acid) and diols (2,3-butanediol [BDO]), reflecting NREL's recently-published 2018 biochemical design report focused on those two pathways. The models were run across three scenarios for lignin utilization, namely combustion, conversion to coproducts based on "base case" performance with biomass hydrolysate, and conversion to coproducts based on "high" performance demonstrated with model lignin monomer components. A key improvement reflected in the 2021 SOT is centered around making use of the latest lignin conversion data, which over the past year focused primarily on production of ß-ketoadipate (BKA) as a more optimal molecule compared to the closely-related adipic acid coproduct of prior recent focus, both in terms of superior product properties and biology, as well as reduced processing complexity (reducing two steps for sequential production of muconate followed by hydrogenation to adipic acid down to a single step for direct production of BKA). This update translated to a roughly 17% increase in mass yield of final coproduct output at a nearly four-fold increase in fermentation productivity on lignin monomers relative to prior 2020 SOT benchmarks for muconic/adipic acid production.

09 BIOMASS FUELS↗