SEARCH · Engineering Papers

Results for “Conditional Normalizing Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Discharge rate of cryogens in microgravity - What ground based experimentation cannot resolve

The discharge of cryogenic vapor and liquid from tanks to a vacuum is examined and the effects of the mass quality, length/diameter ratio, supply tank transient and gravitational environment are discussed. Existing model results and normal gravity experiments are presented which indicate that the homogeneous equilibrium model provides an accurate description of two-phase critical flow for a number of conditions likely to be encountered in practical microgravity systems. Nonequilibrium effects are shown to produce flow rates greater than homogeneous equilibrium model predictions for long tubes with low inlet pressure and short tubes with high inlet pressure.

Purwin, T. P.↗

NASA NTRS1993

Downward Diffusion Flame Spread and Extinction in Variable Gravitational Fields - Lunar and Martian Simulations

This paper describes experimental observations of downward, opposed-flow flame spreading made under partial-gravity conditions aboard NASA research aircraft. Flame spreading and flammability limit behavior of a thin cellulosic fuel tested at normal pressure in oxygen/nitrogen mixtures of 21 percent oxygen, by volume, and below are described over effective acceleration levels ranging from 0.05 to 0.6 times normal earth gravity. Downward burning flammability and flame spread rates are shown to be enhanced by reductions in gravitational acceleration. These data have fire safety implications for the planning of lunar and Martian outposts.

Sacksteder, Kurt R.↗

NASA NTRS1950

High-Subsonic Performance Characteristics and Boundary-Layer Investigations of a 12 10-Inch-Inlet-Diameter Conical Diffuser

Performance and boundary-layer data were taken in a 12 degree 10-inch inlet-diameter conical diffuser of 2:1 exit- to inlet-area ratio. These data were taken for two inlet-boundary-layer conditions. The first condition was that of a thinner inlet boundary later (boundary-layer displacement thickness, delta* approximately equal to 0.034) produced by an inlet section approximately 1 inlet diameter in length between the entrance bell and the diffuser. The second condition was a thicker inlet boundary layer (delta* approximately equal to 0.120) produced by an additional inlet section length of approximately 6 diameters. Longitudinal static-pressure distributions were measured fro wall static orifices. Transverse total- and static-pressure surveys were made at the inlet and exit stations. Boundary-layer velocity distributions were measured at seven stations between the inlet and exit. These data were obtained for a Reynolds number (based on inlet diameter) range of 1 x 10(exp 6) to 3.9 x 10(exp 6). The corresponding Mach number range was from M = 0.2 to choking. At the maximum-power-available condition supersonic flow was obtained as far as 4.5 inches downstream from the diffuser inlet with a maximum Mach number of M approximately equal to 1.5. The total-pressure loss through the diffuser in percentage of inlet dynamic pressure was approximately 2.5 percent for the thinner inlet boundary later and 5.5 percent for the thicker inlet boundary later over the lower subsonic range. These valued increased with increasing flow rate- the values for the thicker inlet boundary later more than those for the thinner inlet boundary layer. The diffuser effectiveness, expressed as the ratio of the actual static-pressure rise to the ideal static-pressure rise, was about 85 percent for the thinner inlet boundary layer and about 67 percent for the thicker inlet boundary later in the lower subsonic range. These values decrease with increasing flow rate. Separated flow was observed for both inlet-boundary-layer conditions in the region of adverse pressure gradient just downstream of the transition curvature from inlet section to diffuser. The flow for the thinner-inlet-boundary-layer condition did not fully re-establish itself along the diffuser walls. The thicker inlet-boundary-layer flow, while not completely re-establishing the normal flow pattern downstream of the separated region, did re-establish more successfully than the thinner inlet boundary layer.

Little, B. H., Jr.↗

NASA NTRS1964

Tables for Supersonic Flow Around Right Circular Cones at Small Angle of Attack

The solution of supersonic flow fields by the method of characteristics requires that starting conditions be known. Ferri, in reference 1, developed a method-of-characteristics solution for axially symmetric bodies of revolution at small angles of attack. With computing machinery that is now available, this has become a feasible method for computing the aerodynamic characteristics of bodies near zero angle of attack. For sharp-nosed bodies of revolution, the required starting line may be obtained by computing the flow field about a cone at a small angle of attack. This calculation is readily performed using Stone's theory in reference 2. Some solutions of this theory are available in reference 3. However, the manner in which these results are presented, namely in a wind-fixed coordinate system, makes their use somewhat cumbersome. Additionally, as pointed out in reference 4, the flow component perpendicular to the meridian planes was computed incorrectly. The results contained herein have been computed in the same basic manner as those of reference 3 with the correct velocity normal to the meridian planes. Also, all results have been transferred into the body-fixed coordinate system. Therefore, the values tabulated herein may be used, in conjunction with the respective zero-angle-of-attack results of reference 5, as starting conditions for the method-of-characteristics solution of the flow field about axially symmetric bodies of revolution at small angles of attack. As in the zero-angle-of-attack case (ref. 5) the present results have been computed using the ideal gas value of 1.4 for the ratio of the specific heats of air. Solutions are given for cone angles from 2.5 deg to 30 deg in increments of 2.5 deg. For each cone angle, results were computed for a constant series of free-stream Mach numbers from 1.5 to 20. In addition, a solution was computed which yielded the minimum free-stream Mach number for a completely supersonic conical flow field. For cone angles of 27.5 deg and 30 deg, this minimum free-stream Mach number was above 1.5. Consequently, solutions at this Mach number were not computed for these two cone angles.

SUPERSONIC FLOW↗

NASA NTRS1987

Effect of a localized minimum in equatorial field strength on resistive tearing instability in the geomagnetotail

A two-dimensional, resistive-MHD computer code is used to investigate the spontaneous reconnection of magnetotaillike configurations. The initial conditions adopted in the simulations are of two types: (1) in which the equatorial normal magnetic field component B(ze) declines monotonically down the tail, and (2) in which B(ze) exhibits a deep minimum in the near-earth plasma sheet. To represent the case where the earthward convection stops before the X line forms, zero-flow boundary conditions are imposed at the edges of the computational box. The initial configurations are in equilibrium and table within ideal MHD. The dynamic evolution of the system starts after the resistivity is turned on. The main results of these simulations basically support the neutral-line model of substorms and confirm Birn's (1980) computer studies. Spontaneous formation of an X-type neutral point and a single O-type plasmoid with strong tailward flow on the tailward side of the X point is found. The time interval from the turning on of the resistivity to the formation of a plasmoid is much shorter in the case where there is an initial deep minimum. A simple analytic calculation is also carried out to demonstrate why the configuration with a deep minimum is more susceptible to the development of the neutral point.

Hau, L.-N.↗

DOE OSTI2021

Observations of Stably Stratified Flow through a Microscale Gap

This paper reports the findings of a comprehensive field investigation on flow through a mountain gap subject to a range of stably stratified environmental conditions. This study was embedded within the Perdigão field campaign, which was conducted in a region of parallel double-ridge topography with ridge-normal wind climatology. One of the ridges has a well-defined gap (col) at the top, and an array of in situ and remote sensors, including a novel triple Doppler lidar system, was deployed around it. The experimental design was mostly guided by previous numerical and theoretical studies conducted with an idealized configuration where a flow (with characteristic velocity U 0 and buoyancy frequency N ) approaches normal to a mountain of height h with a gap at its crest, for which the governing parameters are the dimensionless mountain height G= (Nh)/U 0 and various gap aspect ratios. Modified forms of G were proposed to account for real-world atmospheric variability, and the results are presented in terms of a gap-averaged value G c . The nature of gap flow was highly dependent on G c , wherein a nearly neutral flow regime (G c <1), a transitional mountain wave regime (G c ~O(1)), and a gap-jetting regime ( G c >O(1)) were identified. The measurements were in broad agreement with previous numerical and theoretical studies on a single ridge with a gap or double ridge topography, although details vary. This is the first ever detailed field study reported on microscale (O(100 m)) gap flows, and provides useful data and insights for future theoretical and numerical studies.

Microscale, Gap, environmental fluid dynamics, win↗

DOE OSTI2023

A Three-Dimensional, Analytical Wind Turbine Wake Model: Flow Acceleration, Empirical Correlations, and Continuity

A new, three-dimensional, analytical, steady-state wake model is presented that includes local flow acceleration near the rotor, improving the wake description compared to existing models. Wake structures such as the momentum deficit and regions of accelerated flow are concisely described with compound and normal Gaussian functions. Large-eddy simulations (LES) are used as training data to develop the model using two in-line turbines under various inflow conditions parameterized by hub-height wind speed and turbulence intensity. Mass conservation is considered by fixing two components of the wake velocity model and optimizing the third to best satisfy continuity; after which, the model performs comparably if not better than existing work with regards to both relative error and mass consistency. The final model demonstrates a high degree of flexibility, making use of empirical correlations to scale across different inflow conditions. The inclusion of these effects is capable of revealing unused opportunities for enhanced power generation by aligning wake trajectories with these regions of accelerated flow.

modeling↗

DOE OSTI2020

A hybrid porous model for full reactor core scale CFD investigation of a prismatic HTGR

Three-dimensional (3-D) Computational Fluid Dynamics (CFD) analysis of a whole nuclear reactor core is a tremendous challenge due to the large geometric volume and complex structures. Here, this research presents a hybrid porous (HP) model to simplify a prismatic High Temperature Gas-cooled Reactor (HTGR) core, so 3-D CFD investigation can be performed on a full reactor core scale. In the HP model, the prototypic small coolant channels in the nuclear fuel blocks are lumped together to form multiple equivalent large coolant channels, and then the porous medium flow model is applied to each of them. Therefore, heat transfer in fuel blocks is computed by a hybrid combination of solid energy and porous flow energy equations. The similarity between the HP model and prototypic model is achieved by deriving the porous flow permeability, inertial resistance factor, and artificial thermophysical properties. Compared with the widely used whole porous (WP) flow model, the HP model preserves more realistic geometric structures, and therefore more accurate physical processes. The General Atomics' Modular High Temperature Gas-cooled Reactor (MHTGR) design was chosen as a prototype to demonstrate the methodology. Simulations were performed using the prototypic CFD model and HP model at steady-state forced circulation, steady-state natural circulation, and transient conditions that correspond to normal operation, extended period of pressurized cool down, and short-term transients after reactor shutdown, respectively. The comparison shows good agreement between the HP model and prototypic model in the maximum fuel temperature, average solid temperature, and helium flow rate, which demonstrates the potential applicability of the HP model for a full reactor core scale simulation in the future. As a benefit, the HP model reduces the mesh quantity by a factor of 50 from a prototypic model. Correspondingly, the computation time was reduced by a factor of at least 30.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1993

Active control of asymmetric conical flow using spinning and rotatory oscillations

The effectiveness of active control on asymmetric flows around circular cones is investigated computationally using cone spinning and rotatory oscillation around its axis. The investigation uses the time-accurate solution of the unsteady, compressible, full Navier-Stokes equations with the implicit, upwind, flux-difference splitting, finite-volume scheme. The present solutions are obtained under the locally-conical-flow assumption in order to understand the flow physics using very fine grids for reasonable flow resolution at low computational cost. For all the computational solutions, a grid of 241 x 81 x 2 points in the wrap-around, normal and axial directions, respectively, is used. The grid is spinning or oscillating rigidly with the cone according to its motion and the kinematical and dynamical boundary conditions are modified accordingly. The computational applications include the effects of uniform spinning rates and periodic rotatory oscillations at different amplitudes and frequencies on the flow asymmetry.

Kandil, Osama A.↗

NASA NTRS1984

Ultrasonic and optical evaluation of surgical implant materials and devices. A durability study of pericardial bioprostheses

Laser Doppler Anemometry (LDA) and accelerated fatigue testing were used in an attempt to assess the durability of two cardiac value bioprostheses. The LDA system was used to monitor the function of the cardiac valves over time. This was done through flow characterization in an aortic flow chamber, designed to closely simulate in vivo conditions, both in the near vicinity (sinuses of valsalva region) and also somewhat downstream (aortic region) from the values. The accelerated fatigue tester was operated by opening and closing the valves at a rate of 1300 R.P.M., about 18 x the normal rate. The results from the two test valves indicate a definite change in the flow characteristics downstream from the valve after certain accelerated test intervals. The high velocity cross-sectional flow area seems to increase over time in use, causing a decrease in the peak velocity. The tissue became more flaccid in certain areas, and tears were apparent at about 9.4 million cycles for the Ionescu-Shiley valve and at 24 million cycles for the Carpentier-Edwards valve. The use of Doppler ultrasound as a technique for monitoring the function of bioprostheses over time in vivo is also discussed.

Schuster, P. R.↗

NASA NTRS1998

Perfectly Matched Layer for Linearized Euler Equations in Open and Ducted Domains

Recently, perfectly matched layer (PML) as an absorbing boundary condition has widespread applications. The idea was first introduced by Berenger for electromagnetic waves computations. In this paper, it is shown that the PML equations for the linearized Euler equations support unstable solutions when the mean flow has a component normal to the layer. To suppress such unstable solutions so as to render the PML concept useful for this class of problems, it is proposed that artificial selective damping terms be added to the discretized PML equations. It is demonstrated that with a proper choice of artificial mesh Reynolds number, the PML equations can be made stable. Numerical examples are provided to illustrate that the stabilized PML performs well as an absorbing boundary condition. In a ducted environment, the wave mode are dispersive. It will be shown that the group velocity and phase velocity of these modes can have opposite signs. This results in a confined environment, PML may not be suitable as an absorbing boundary condition.

Tam, Christopher K. W.↗

NASA NTRS1993

Small hydrogen/oxygen rocket flowfield behavior from heat flux measurements

The mixing and heat transfer phenomena in small rocket flow fields with fuel film cooling is not well understood. An instrumented, water-cooled chamber with a gaseous hydrogen/gaseous oxygen injector was used to gather steady-state inner and outer wall temperature profiles. The chamber was tested at 414 kPa (60 psia) chamber pressure, from mixture ratios of 3.41 to 8.36. Sixty percent of the fuel was used for film cooling. These temperature profiles were used as boundary conditions in a finite element analysis program, MSC/NASTRAN, to calculate the local radial and axial heat fluxes in the chamber wall. The normal heat fluxes were then calculated and used as a diagnostic of the rocket's flow field behavior. The normal heat fluxes determined were on the order of 1.0 to 3.0 MW/meters squared (0.6 to 1.8 Btu/sec-inches squared). In the cases where mixture ratio was 5 or above, there was a sharp local heat flux maximum in the barrel section of the chamber. This local maximum seems to indicate a reduction or breakdown of the fuel film cooling layer, possibly due to increased mixing in the shear layer between the film and core flows. However, the flow was thought to be completely laminar, as the throat Reynolds numbers were below 50,000 for all the cases. The increased mixing in the shear layer in the higher mixture ratio cases appeared not to be due to the transition of the flow from laminar to turbulent, but rather due to increased reactions between the hydrogen film and oxidizer-rich core flows.

Reed, Brian D.↗

DOE OSTI2022

Simulation of the High Temperature Test Facility (HTTF) Core Using the 2D Ring Model with SAM

A two-dimensional ring model is developed with SAM to model the core of the High Temperature Test Facility (HTTF) at the system level. The ring model simplifies the complex structure of the HTTF core by converting the hexagonal rows of heaters and flow channels into layers of concentric annular rings. The ring model is first compared against a 3D-1D model where the solid structures are fully resolved in three dimensions while the fluid structures are modeled as one-dimensional flows. Comparison between the 3D-1D and the ring models shows that the latter can predict major parameters reasonably well under steady-state normal operating condition, but the heater temperatures are underpredicted. Adjustment is made to the effective thermal conductivity of the ceramic core of the ring model to improve the heater temperature predictions. Furthermore, the ring model is also used to simulate a transient Pressurized Conduction Cooldown (PCC) condition and is benchmarked with the experimental data from the HTTF Test PG-27. Good agreement is obtained between the experimental data and the predictions by the ring model.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1978

A new battery charger/discharger converter

A new optimum topology dc-to-dc switching converter is extended to provide bidirectional current flow. The resulting two-quadrant converter can be employed to eliminate the discontinuous current mode in normal unidirectional applications, but is especially suited for spacecraft battery conditioning as a charge-discharge regulator in place of the conventional separate converters. Implementation of the control features and the battery charge current and voltage limits are discussed.

Middlebrook, R. D.↗

NASA NTRS1982

On the impingement of supersonic jet on a normal flat surface

An improved method, based on one strip approximation of the method of integral relations which was reported originally by Belov, Ginzburg and Shub (1973), is presented for the calculation of flow parameters in the impingement region of a supersonic, underexpanded jet striking a normal surface located within the first cell. The results are presented for two impingement conditions and found to be in good agreement with the experimental data.

Pamadi, B. N.↗

NASA NTRS1951

Internal Flow and Burning Characteristics of 16-inch Ram Jet Operating in a Free Jet at Mach Numbers of 1.35 and 1.73

The effects of mass-flow ratio on the additive drag and normal-shock position of a single oblique-shock diffuser are presented. Also evaluated is the variation with operating condition of the velocity distribution at the combustion-chamber inlet. A comparison with connected-pipe data is included. Burner performance with a corrugated gutter-grid flame holder is discussed. It is shown that the total-pressure drop across the combustion chamber can be predicted with reasonable accuracy from the computed flame holder and combustion momentum pressure losses.

DIFFUSERS, SUPERSONIC↗

NASA NTRS2001

An Earth-Based Equivalent Low Stretch Apparatus to Assess Material Flammability for Microgravity & Extraterrestrial Fire-Safety Applications

One of the performance goals for NASA's enterprise of Human Exploration and Development of Space (HEDS) is to develop methods, data bases, and validating tests for material flammability characterization, hazard reduction, and fire detection/suppression strategies for spacecraft and extraterrestrial habitats. This work addresses these needs by applying the fundamental knowledge gained from low stretch experiments to the development of a normal gravity low stretch material flammability test method. The concept of the apparatus being developed uses the low stretch geometry to simulate the conditions of the extraterrestrial environment through proper scaling of the sample dimensions to reduce the buoyant stretch in normal gravity. The apparatus uses controlled forced-air flow to augment the low stretch to levels which simulate Lunar or Martian gravity levels. In addition, the effect of imposed radiant heat flux on material flammability can be studied with the cone heater. After breadboard testing, the apparatus will be integrated into NASA's White Sands Test Facility's Atmosphere-Controlled Cone Calorimeter for evaluation as a new materials screening test method.

Olson, S. L.↗

NASA NTRS2002

Parametric Study of Carbon Nanotube Production by Laser Ablation Process

Carbon nanotubes form a new class of nanomaterials that are presumed to have extraordinary mechanical, electrical and thermal properties. The single wall nanotubes (SWNTs) are estimated to be 100 times stronger than steel with 1/6th the weight; electrical carrying capacity better than copper and thermal conductivity better than diamond. Applications of these SWNTs include possible weight reduction of aerospace structures, multifunctional materials, nanosensors and nanoelectronics. Double pulsed laser vaporization process produces SWNTs with the highest percentage of nanotubes in the output material. The normal operating conditions include a green laser pulse closely followed by an infrared laser pulse. Lasers ab late a metal-containing graphite target located in a flow tube maintained in an oven at 1473K with argon flow of 100 sccm at a 500 Torr pressure. In the present work a number of production runs were carried out, changing one operating condition at a time. We have studied the effects of nine parameters, including the sequencing of the laser pulses, pulse separation times, laser energy densities, the type of buffer gas used, oven temperature, operating pressure, flow rate and inner flow tube diameters. All runs were done using the same graphite target. The collected nanotube material was characterized by a variety of analytical techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman and thermo gravimetric analysis (TGA). Results indicate trends that could be used to optimize the process and increase the efficiency of the production process.

Arepalli, Sivaram↗