Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Clay”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Produced Fluid Induced Mineralogy and Elemental Alterations of Caney Shale, Southern Oklahoma

ABSTRACT This study involves batch reactor experiments and subsequent analyses of samples from Caney Shale in the Ardmore Basin of South-Central Oklahoma. Samples include mainly rock cores and cuttings recovered from two wells respectively drilled vertically through and horizontally across the Caney Shale. Mineralogical compositions are obtained by X-Ray Diffraction (XRD) measurements whilst microstructure and elemental distribution are acquired by Scanning Electron Microscopy/Energy Dispersive Spectroscopy (SEM/EDS) respectively. Batch experiments are then conducted using selected rock samples and produced fluid from the Caney Formation. Deionized water is also reacted with some samples to serve as standard. Experiments are conducted at 95°C and ambient pressure for 7 and 30 days to assess the geochemical rock-fluid interactions. Results show rock mineralogical compositions are predominantly quartz, feldspar, carbonates, and clay with minor pyrite. Post-experimental mineralogical changes observed in samples include increased amorphous entities especially within the clay portions of XRD plots and dissolution of feldspar and carbonate minerals and formation of new mineral phases, mostly clays and salts. These are corroborated by EDS elemental analyses which show decreased elemental compositions. The implications of reactions mentioned above include but not limited to, scale formation, clay fines migration and shale softening all of which pose significant permeability impairment on formation over time. INTRODUCTION Shale reservoirs account for a large share of unconventional reservoirs in the world (Lyu et al., 2015). However, ultra-low permeability and high clay compositions pose significant challenges when producing from these reservoirs (Dawuda and Srinivasan, 2022, 2023). Producing from these reservoirs therefore requires horizontal drilling and hydraulic fracturing technologies which have proven their efficacy in generating substantial permeability in reservoirs to ensure production (Fujian et al., 2019; Liu et al., 2018). Even after expensive horizontal drilling and hydraulic fracturing, geochemical reactions between engineered fluids and formation leads to fracture constriction and adversely impact petrophysical properties (permeability and porosity) of the reservoir. These technologies are therefore under constant development and improvement in various aspects to ensure fine tuning for specific reservoirs. Under present conditions, much of the hydrocarbon reserves in unconventional shale reservoirs are left unproduced due to rapid decline in permeability following resumption to production after hydraulic fracturing. It is therefore essential to understand the range of geochemical reactions that cause rapid depletion of permeability after hydraulic fracturing and apply these to each shale reservoir to ensure substantial recovery rates.

Awejori, G. A.↗
DOE OSTI2024

Comparison of Geochemical Reactivity of Marcellus and Caney Shale Based on Effluent Analysis

ABSTRACT: In this comparative study, we analyzed the changes in elemental concentrations of hydraulic fracturing fluids after interaction with the Marcellus and Caney Shale formations. The focus was on assessing the inherent risks and environmental implications associated with flowback waters, including their impact on soil, ground, and drinking water quality, and human health safety. The chemical compositions of effluents were determined through Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES) and Mass spectrometry (ICP-MS). The Marcellus Shale, showed concentrations of Cd, averaging 0.380 ppm far exceeding safe water thresholds. Significant levels of As, Se, B, and Pb were detected in both shales, raising concerns about soil and water contamination. Analyzing the effluents from representative samples of sections of the Marcellus (S2 and S7) and Caney (R1 and R2) indicates different geochemical responses over 4 weeks of experiments. This comparison underscores the chemical changes and environmental considerations linked to hydraulic fracturing across shale formations, suggesting the value of tailored monitoring and regulatory measures for each type. 1. INTRODUCTION The Caney and Marcellus shales, differing in geology and geochemistry, represent distinct unconventional reservoirs. The Caney shale, is more ductile, with higher produced water volumes, (Smith et al., 2022) contrasts with the brittle Marcellus shale known for lower brine production but significant data availability. This study aims to elucidate the possible environmental health and safety issues that may arise from the hydraulic fracturing processes. The interaction between fracturing fluids and clays presents a significant challenge. The primary base of these fluids is water, which, when introduced to clay, can induce swelling and constrict flow pathways. This phenomenon is attributed to water molecules infiltrating the layers of clay, particularly in 2:1-type clays, leading to an increased distance between layers. To counteract this, clay stabilizers are employed (Awejori et al., 2021). Despite their effectiveness, these stabilizers are considered temporary solutions. Upon completion of the fracturing process, a concomitant amount of contaminated waters (flow back), with varied content is collected at the surface. From these, we can infer the geochemical reactions and the environmental challenges associated with these waters. Flowback waters can be reinjected or used for other purposes such as irrigation. This requires adequate screening and treatment for safe use.

Dje, L. B.↗
NASA NTRS1987

Chemical and spectroscopic characterization of a suite of Mars soil analogs

The National Aeronautics and Space Administration has begun preparations for the flight of the Mars Observer Mission in the early 1990s. An advanced ground-based study is being conducted on a usefully limited suite of Mars Soil Analog Materials (MarSAM) intended to simulate the aeolian material covering the surface of Mars. A series of variably proportioned iron/calcium smectite clays were prepared from a typical montmorillonite clay using the Banin method. The effect of increasing iron on a diverse set of chemical and spectroscopic properties of the suite of clays is discussed. In order to chemically characterize the MarSAM and compare them with the Martian soil studied by Viking, the clays were analyzed for their major and minor elemental compositions by X-ray fluorescence and ion-coupled plasma techniques. It was concluded that the surface iron has a complex and hitherto uninvestigated impact on the catalytic and spectroscopic properties of clays and on the ability of these material to store energy.

Coyne, L. M.↗
NASA NTRS1988

Nitrogen geochemistry of a Cretaceous-Tertiary boundary site in New Zealand

Nitrogen in the basal layer of the K-T boundary clay at Woodside Creek, New Zealand, has an abundance of 1100 ppm, a 20-fold enrichment over Cretaceous and Tertiary values. The enrichment parallels that for Ir and elemental carbon (soot); all decrease over the next 6 mm of the boundary clay. The C/N ratio, assuming the nitrogen to be associated with organic rather than elemental carbon, is approximately 5 for the basal layer compared to 20 to 30 for the remainder of the boundary clay. The correlation between N and Ir abundances appears to persist above the boundary, implying that the N is intimately associated with the primary fallout and remained with it during the secondary redeposition processes that kept the Ir abundance relatively high into the lowermost Tertiary. Apparently the basal layer of the boundary clay represents the accumulation of a substantial quantity of N with an isotopic composition approximately 10 percent heavier than background delta value of N-15 values. If the boundary clay represents an altered impact glass from a meteorite impact than it probably denotes a time period of less than 1 year. Therefore, the changes in nitrogen geochemistry apparently occurred over a very short period of time. The high abundance of N and the correspondingly low C/N ratio may reflect enhanced preservation of organic material as a result of the rapid sweepout and burial of plankton by impact ejecta, with little or no bacterial degradation. It is conceivable that the shift in delta value of N-15 may represent an influx of nitrogen from a different source deposited contemporaneously with the impact ejecta. An interesting possibility is that it may be derived from nitrate, produced from the combustion of atmospheric nitrogen.

Gilmour, Iain↗
NASA NTRS1992

Preliminary results of an experimental study of the interactions of basalt glass and a water vapor atmosphere: Implications for weathering on Mars

Models of weathering processes on the surface of Mars invoke hydrothermal alteration as the primary mechanism responsible for clay formation. Previous experimental studies of basalt glass interactions with water under hydrothermal conditions demonstrate that phyllosilicates and zeolites are the primary alteration minerals. Gas-solid weathering is thought to be less thermodynamically favorable and relatively unimportant, however, the experimental alteration of basalt glass under vapor ion conditions (large SA/V) can result in the formation of clay minerals, zeolites, and hydrated calcium silicates. We have undertaken a study of the reacted layers formed on basalt glasses experimentally altered under vapor hydration conditions to resolve this issue. High SA/V ratios promote reaction product buildup in solution and promote alteration mineral formation. It was previously shown that these reaction conditions promote weathering processes similar to those found in nature for tektite glasses, rhyolitic glasses, and basalt glasses. The hydration of basalt glass is described for 100 percent relative humidity experiments at temperatures of 150, 175, and 200 C for up to 400 days. Preliminary characterization of the alteration layers with analytical electron and scanning microscopy suggest that the reaction mechanism includes precipitation of a smectite clay on the outermost surface of the glass. Between the clay and the unreacted glass is an amorphous gel-like phase (palagonite). Our results provide an experimental basis for proposing that basalt glass interactions with vapor atmospheres can be an important source of clay minerals.

Mazer, J. J.↗
NASA NTRS2002

Preparation and Characterization of Polyimide/Organoclay Nanocomposites

Organically modified montmorrrillonite clay, containing a long chain aliphatic quarternary ammonium cation, was used to prepare polyimide/organoclay hybrids. Several approaches were examined in an attempt to achieve fully exfoliated nanocomposites. These included simple mixing of the clay in a pre-made high molecular weight poly(amide acid) solution; simple mixing followed by sonication of the organoclay/poly(amide acid) solutions; and the preparation of high molecular weight poly(amide acid)s in the presence of the organoclay dispersed in N-methyl-2-pyrrolidinone (NMP). The best results were obtained using the in-situ polymerization approach. The resulting nanocomposite films (both amide acid and imide), containing 3-8% by weight of organoclay, were characterized by differential scanning calorimetry (DSC), dynamic thermogravimetric analysis (TGA), transmission electron microscopy (TEM), X-ray diffraction (XRD), and thin film tensile properties. A significant degree of dispersion was observed in the nanocomposite films of the amide acid and the imide. After thermal treatment of amide acid films to effect imidization, in both air and nitrogen, the films were visually darker than control films without clay and the level of clay dispersion appeared to have decreased. In the latter case, the separation between the layers of the clay decreased to a spacing less than that present in the original organoclay. These observations suggest that thermal degradation of the aliphatic quarternary ammonium cation occurred likely during thermal treatment to effect imidization and solvent removal. These thermal degradation effects were less pronounced when thermal treatment was performed under nitrogen. The polyimide/organoclay hybrid films exhibited higher room temperature tensile moduli and lower strength and elongation to break than the control films.

Delozier, D. M.↗
NASA NTRS2003

Polyimide Nanocomposites Prepared from High-Temperature, Reduced Charge Organoclays

Montmorillonite clays modified with the dihydrochloride salt of 1,3-bis(3-aminophenoxy)benzene (APB) were used in the preparation of polyimide/organoclay hybrid films. Organoclays with varying surface charge based upon APB were prepared and examined for their dispersion behavior in the polymer matrix. High molecular weight poly(amide acid) solutions were prepared in the presence of the organoclays. Films were cast and subsequently heated to 300C to cause imidization. The resulting nanocomposite films, containing 3 wt% of organoclay, were characterized by transmission electron microscopy and X-ray diffraction. The clay's cation exchange capacity (CEC) played a key role in determining the extent of dispersion in the polyimide matrix. Considerable dispersion was observed in some of the nanocomposite films. The most effective organoclay was found to have a CEC of 0.70 meq/g. Nanocomposite films prepared with 3-8 wt% of this organoclay were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and thin-film tensile testing. High levels of clay dispersion could be achieved even at the higher clay loadings. Results from mechanical testing revealed that while the moduli of the nanocomposites increased with increasing clay loadings, both strength and elongation decreased.

Delozier, D. M.↗
NASA NTRS2019

Partially Chloritized Smectites: Analogues of Smectites at Gale Crater, Mars

Characterizing the structure and composition of phyllosilicates is important for interpreting the aqueous history of Mars and identifying potential habitable environments. Smectites and chlorites are the most dominant clay types on Mars, and there is evidence of the presence of smectite/chlorite intergrades. Smectite has been detected at Gale Crater, Mars, via orbital observations and in-situ measurements, in abundances up to approximately 25 weight percentage of bulk rock. John Klein (JK) and Cumberland (CB) were analyzed by the Chemistry and Mineralogy (CheMin) and Samples Analysis at Mars (SAM) evolved gas analysis experiment (EGA) instruments, onboard Mars Science Laboratory (MSL), Curiosity, to distinguish clay mineralogy. John Klein has a collapsed 2:1 smectite with a d-spacing of 10 Angstroms, whereas Cumberland smectite did not fully collapse and has a d-spacing of approximately 13.2 Angstroms. It has been suggested that partial chloritization or ‘pillaring’ could be responsible for the expanded Cumberland smectite because pillaring inhibits the collapse of smectites down to 10 Angstrom, even under the desiccating conditions on the martian surface. Clay minerals have been detected in ancient fluvio-lacustrine rocks throughout Curiosity’s traverse and catalog the changes of the lake water chemistry and diagenetic conditions at Gale Crater, Mars. Investigating clay minerals is important for identifying them on the Martian surface, in particular as Curiosity proceeds into the upcoming Clay-bearing Unit.

Tu, V. M.↗
NASA NTRSDate not supplied

High Resolution Imaging and Analysis of Terrestrial Impact Glass: Amorphous Materials, Phyllosilicates and Everything in Between

Introduction: Impact cratering is one of the most ubiquitous geologic processes shaping the surface of all solid bodies in our solar system. Impacts are also a major source of clay minerals, poorly crystalline clay-like phases and amorphous (i.e., lacking long-range atomic order) materials on Earth and Mars. Phyllosilicates and amorphous materials have consistently formed a major component (~20-70 wt%) of every single drilled rock and soil sample in Gale Crater on Mars, as determined by the CheMin instrument on Curiosity. The origin of the amorphous component is speculative, but could be primary impact or volcanic-produced glass(es) deposited via aeolian or fluvial processes, secondary aqueous alteration products or chemical precipitates; it is likely to be a combination of all three possibilities. Efforts to determine the composition of these materials across the rover’s traverse through Gale Crater are ongoing. Naturally occurring amorphous phases are found in a variety of environments on Earth, and terrestrial analogue studies may help shed light on how they may have formed on Mars. Primary and altered impact glass are likely widespread on Mars and may have contributed to the amorphous component found throughout Gale Crater. In its pristine, unaltered state, impact glass (i.e., melt glass) is considered amorphous. However, truly unaltered glass is rarely preserved in crater fill impactites as it quickly alters in the post-impact environ-ment, commonly forming a mixture of hydrated aluminosilicate phases whose structures are not always discernable at the microscale (i.e., they may be amorphous or contain short-range order). These phases are part of an incredibly complex group of materials; differences in their composition and crystalline structure (or lack thereof) and genetic relationship to the more well-crystalline clay minerals are often only discernable at the nanoscale, beyond the resolution of traditional X-ray diffractometers (XRD) and scanning electron microscopes/microprobes (SEM/EPMA) alone. In this contribution, we summarize recent results from ongoing characterization of clay minerals, poorly crystalline clay-like phases, and amorphous materials preserved in altered terrestrial impact glass from the Chicxulub (~66 Ma) and Ries (~15 Ma) impact structures. This work has been performed using a combination of high-resolution transmission electron microscopy (HR-TEM), SEM, microprobe/EPMA, Raman spectroscopy and XRD.

Impact crater↗
DOE OSTI2021

Pilot-Scale Testing of an Integrated Circuit for the Extraction of Rare Earth Minerals and Elements from Coal and Coal Byproducts Using Advanced Separation Technologies

The primary objective of this project was to develop and demonstrate an integrated pilot-scale circuitry for recovering high-value rare earth elements (REEs) from coal and coal byproducts. The target performance was to produce a mixed REE product with content of at least two percent by weight on a dry mass basis in a cost-effective and environmentally benign manner. During the first nine months of the project period (Phase 2 Budget Period 2), pilot plant construction was completed including all field site startup activities such as permitting, engineering design, procurement/bidding, unit fabrication, site construction, equipment installation, module assembly, safety training, and circuit shakedown. During the remaining 21 months of project period (Phase 2 Budget Period 3), detailed field-testing activities were performed including feedstock sample collection and preparation, exploratory testing, circuit modification, detailed parametric study, and performance optimization. A detailed techno-economic analysis was performed based on the pilot plant testing findings which provided various scenarios for REE production. The project successfully accomplished the proposed target performance by producing mixed rare earth oxide (REO) with greater than 90% purity by weight in a continuous pilot scale operation from two distinctly different coarse refuse materials (i.e., West Kentucky No. 13 and Fire Clay coal seams), and at least three secondary sources (i.e., heap leach process and naturally formed acid mine drainage system). Project partners included the University of Kentucky, Virginia Tech, West Virginia University, Alliance Coal, Blackhawk Mining, Mineral Refining Company, and Mineral Separation Technologies. The pilot scale test facility was constructed at a former mining complex owned by Alliance Natural Resource Partners (Alliance Coal). The site was rehabilitated to accommodate the equipment installation, construction and fabrication, electrical power requirement, water line management and containment. The process units constructed and installed included X-ray sorting unit, crushing and grinding unit, physical separation unit, acid leaching unit, solvent extraction unit, and wastewater management unit. A rare earth mineral concentration unit was constructed as a standalone unit for flexible operation. A detailed environmental assessment and control plan was carried out to identify and quantify any potential impacts of the pilot-scale processing circuitry on the human and eco-system health and well-being. Corresponding mitigation strategies and control measures were provided. A conceptual flowsheet was developed to effectively remove thorium and uranium from high purity rare earth oxide mix or any potential radionuclide enriched stream. The two distinct feedstock materials were secured from the Blackhawk Mining Complex in eastern Kentucky where the Fire Clay (Hazard No. 4) seam is processed. The West Kentucky No. 13 (Baker) coarse refuse material was collected from an active process stream at an Alliance coal preparation plant located in western Kentucky. Characterization analysis indicated that both of feed materials generated from the two sources contained >300 ppm of TREEs on a dry whole mass basis which met the requirements for a qualified feed stock. The two feedstocks were further upgraded using a dual x-ray sorter to prepare the feed material for hydrometallurgical circuit. Thermal treatment on feed material prior to leaching was found to: 1) improve the leaching recovery of REEs, 2) increase the leaching kinetics, and 3) allow the leaching reaction to occur at lower acidity. Roasting at 600°C was selected as the pre-treatment condition for both West Kentucky No. 13 and Fire Clay coarse refuse material. Over 40% of leaching recovery was achieved by roasting West Kentucky No. 13 material having a top particle size of 3 mm in the pilot scale operation using 1.2M sulfuric acid leaching at 75OC. Initial pilot scale testing involved continuous operation of the pilot plant for 94 hours. The leaching unit was operated at solid-to-liquid ratio of 1 to 10 (w/v) using 0.5M sulfuric acid solution at a temperature of 75°C. The continuous solvent extraction circuit utilized rougher and cleaner units with DEHPA and TBP as the extractants. An innovative stripping circuit was developed to accumulate the REE concentration in the stripping solution to a level above 600 ppm. A bleed stream from the recycled strip solution was treated using oxalic acid precipitation which produced a high grade rare earth oxalate. The oxalate product was roasted to remove the oxalate which produced a rare earth oxide product having a purity greater 90%. Due to high concentrations of contaminant ions in the pregnant leach solution (PLS), a modified flowsheet was developed that involved pre-concentration of the REEs using multiple stages of precipitation and redissolution. The advantage of this process was improved removal of contamination before the downstream purification process and a significant cost reduction relative to the circuit that utilized the solvent extraction process. The modified circuitry included processes involving leaching, multistage precipitation, redissolution, and oxalate precipitation followed by roasting of the oxalate product. The circuit produced a mixed REO that was 92.96% pure from the initial test. A detailed parametric test plan was carried out which involved varying key parameters including solids feed rate, acid flowrate, acid concentration, multistage precipitation pH, redissolution pH, oxalate precipitation dosage and pH. The response variables included REE recovery, contaminant recovery, REO product grade and overall chemical consumption. Test results indicated that the acid-to-solid ratio is the key parameter to leaching efficiency as performance deteriorated with an increase in solids concentration. The optimal pH determined for REE precipitation and redissolution was 6.5 and 2.5, respectively. Additional tests were conducted to further improve the flowsheet. Recirculating a portion of the PLS to the feed of the leach tanks improved the leaching performance by lowering the pH of the leaching system and reducing the contamination recovery by shortening the residence time. Moreover, the removal of Al prior to REE precipitation significantly reduced the oxalic acid consumption in the oxalate precipitation circuit. The modified circuit produced over 90% grade REO by weight from both West Kentucky No. 13 and Fire Clay coarse refuse material in pilot scale continuous test programs. A case analysis model was developed to project the REE and major contaminants concentration in each PLS stream based on the leaching condition, pH cut point, and oxalic acid dosage. A correlation was established using empirical and semi-empirical models. Using the models, chemical consumption required for each stage was predicted based on the projected performance of the hydrometallurgy circuit. After identifying the optimum conditions, validation tests were carried out for the treatment of both West Kentucky No. 13 and Fire Clay coarse refuse materials in the pilot plant. The actual circuit performance and chemical consumptions were very close to the model predictions. Other than the two coarse refuse sources, several secondary feedstocks were also tested in the pilot plant facility. A “heap leach” system was constructed using the coarse refuse material generated from cleaning the West Kentucky No. 13 seam coal. Using the two stage SX rougher and cleaner circuit, a concentrate with a grade >90% REO was produced while recovering >97% of the REEs from the heap leach PLS. Naturally generated acid mine drainage (AMD) from West Kentucky No.13 mine was processed using the multistage precipitation circuit in the pilot plant in a test conducted for a period of 32 hours. The final grade of the mix RE oxide produced from the AMD was 90.84% with an overall circuit recovery of 64%. The primary source of REE was the selective precipitation steps involving iron and aluminum rejection. The hydrophobic-hydrophilic separation (HHS) process was proven to effectively recover coal from fine waste materials. For REM recovery, the HHS process was able to produce concentrates at grades of approximately 1.8% REE on an ash basis; however, recovery values were typically low, <10%, under the optimal conditions determined in the laboratory-scale testing. Staged testing of the pilot-scale HHS process for coal recovery and semi-continuous laboratory testing for REM testing showed that a total concentration ratio of more than 15x was observed for the REM recovery process. A circuit simulation package was developed for REE extraction and purification using a spreadsheet-based platform (Microsoft Excel). The REESim circuit simulation package is configured to track the mass and volume flows of components passing through a series of unit operations specified and configured by the user. The mass rates can then be utilized by the user to determine important performance indicators such as product mass yields, concentrate purity levels, element-by-element recoveries, and so forth. The techno-economic analysis showed that the roasting and leaching operations were the most expensive capital items, each contributing approximately 30% to the total capital cost. One notable contributor to the high production costs was the low REE recovery observed in the pilot scale trials. The product basket price was shown to have a strong influence on the economic viability of the scenarios, with the scandium price being the most significant influencer. Operating cost was shown to be extremely sensitive to REE recovery, REE feed grade, and leaching acid consumption. An analysis of ten different scenarios for a 500 t/h commercial operation revealed that three were economically favorable, producing internal rates of return varying from 27.7% to 33.1% and payback periods of 4 to 5 years. The project successfully developed and demonstrated a process to recover REEs from coal and coal byproducts in a pilot-plant operation which consistently produced over 90% grade REO mix from varies types of feedstocks. Commercialization analysis showed that the technology readiness level successfully achieved TRL 6 at the end of the project and demonstrated the need and the potential for scaling the process to further advance the technologies toward the goal of providing a domestic supply of REEs at a commercial scale.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Encapsulation method for preparation of pellets with high attrition resistance

This disclosure provides a method to produce highly attrition resistant pellets by encapsulating reactive components in a vitrified clay outer layer. The reactive component mixture is present relative to the clay substrate in a weight ratio of part per 60-100 part to about 60 parts of the clay substrate. The reactive components are agglomerated first, and clay substrate is added to form the outer layer of the pellet. The pellets are calcined at temperatures above 1200 C to form a vitrified clay semi porous outer layer providing high strength to the pellet while facilitating the gas transfer for the reaction with the encapsulated reactive components. Pellets containing CuO—Fe 2 O 3 -alumina oxygen carrier for chemical looping combustion of fuel demonstrated high attrition resistance and high reactivity with methane.

Siriwardane, Ranjani↗
DOE OSTI2023

AN ACID BAKING APPROACH TO ENHANCE RARE EARTH ELEMENT RECOVERY FROM BITUMINOUS COAL SOURCES

Rare earth elements (REE) are a group of 17 elements typically classified as light and heavy rare earth elements, which play a crucial role in developing the latest technologies for energy, defense, and medical sectors. Even though REEs have been found in more than 200 minerals, only bastnaesite, monazite and xenotime are commercially exploited for REE extraction. However, the recent exponential increase in REE demand has spurred countries such as the United States into research for the extraction of REEs from secondary sources such as coal, acid mine drainage, and coal ash. Several coal sources (e.g., Fire Clay seam coal) across the United States have been identified to contain elevated concentrations of rare earth elements (>600 ppm), and various researchers have investigated the feasibility of both physical and hydrometallurgical extraction techniques for rare earth concentration and subsequent extraction. However, both physical and direct leaching were concluded to be inefficient for RE beneficiation and extraction due to low recoveries. Alternatively, thermal treatment provides promising means for RE recovery from bituminous coal sources. The positive impact of thermal treatment/calcination was established to be due to the decarbonization and dehydroxylation of the clays, which released entrapped rare earth elements within the dominant minerals and converted them into an acid-soluble form. Nonetheless, the improvement in recovery was limited to the light REEs (LREEs) with an insignificant increase in the heavy REEs (HREE). It was demonstrated that the light and heavy REEs in the material were associated with difficult-to-leach minerals such as monazite, xenotime, and zircon, which were not decomposed by simple calcination due to their high thermal stability. Hence, roasting in the presence of chemicals was necessary to ensure the decomposition of those REE-containing minerals. As such, this study was focused on the acid baking treatment of bituminous coals with an aim to enhance REE recovery, especially HREEs. Based on the presence of REE minerals like monazite and xenotime, three pre-leach treatment methods, i.e., 1) roasting, 2) direct acid baking, and 3) acid baking after roasting were investigated. Roasting tests at 600 ⁰C revealed that the recovery of light REEs (LREEs) was enhanced while the recovery of HREEs remained relatively unaffected. LREE and HREE recovery values of 38.3% and 21.3%, respectively, were achieved using a 50 g/L sulfuric acid solution at 5% solid concentration and a solution temperature of 75 ⁰C for 2 hours. Comparatively, direct acid baking at 250 °C provided substantial increased LREE and HREE recovery values to approximately 49.4% and 53.0%, respectively, using an equivalent acid dosage. Recoveries were maximized to 77.0% and 79.6% for LREE and HREE, respectively, by roasting followed by acid baking. Similar results were obtained from the treatment of a second bituminous coal source. Due to strong correlations between REE and Al recovery values, tests were performed on kaolinite and illite, which were prominent clay minerals within the source coals. These experiments revealed that the REE recovery improvements were likely a result of dehydroxylation of clays and subsequent release and decomposition of REE-bearing minerals such as monazite, xenotime and zircon. Subsequently, a parametric study was conducted to identify the impact of acid baking parameters on rare earth element recovery. The factors investigated using a three-level statistical experimental program were acid baking time, acid solution concentration, baking temperature, and acid solution-to-solids ratio which were found to significantly impact REE and contaminant element (Al, Fe, and Ca) recovery. An increase in baking temperature up to around 250 ⁰C improved the light and heavy REE recovery values by more than 50 absolute percentage points relative to performances achieved when direct leaching. As aforementioned, acid baking was needed to both decompose the clay minerals and liberate the REE minerals, which allowed access for the acid to solubilize the REEs. Acid concentration of the solution used for acid baking was studied as a means of minimizing the amount of acid needed to achieve a target REE recovery. However, thermo-gravimetric and differential scanning calorimetry analysis (TGA-DSC) of sulfuric acid under oxidizing atmosphere revealed that the addition of water decreased the evaporation temperature, which explains the lower REE recovery values obtained when using acid concentrations less than 100%. Using pure sulfuric acid at an acid-to-solid ratio of 0.8:1 resulted in recovery values of around 70% for both LREEs and HREEs. The decomposition reaction time was relatively quick with 65% of the TREEs recovered within the first 10 minutes. Following the identification of optimum operating conditions through the parametric study, a systematic leaching study was carried out to examine the impact of leaching parameters, such as solid-to-liquid (S/L) ratio, temperature, and time, on REE recovery using acid baking conditions of 1:1 acid to solids ratio at 250 °C for 30 minutes. The solid-to-liquid ratio was varied from 1-20% by weight at 25 °C, 50 °C, and 75 °C solution temperatures. The results indicated that reaction time and solution temperature considerably impacted the recovery of heavy and light REEs. Interestingly, LREE recovery reduced from 68% at 5% S/L to 58% at 20%S/L, whereas HREE recovery of 78% remained unaffected. The decrease in the LREE recovery was determined to be due to La and Ce precipitation, likely through isomorphic substitution with calcium in gypsum. The kinetic data indicated that 67% LREE and 77% HREE recovery could be obtained within the first 15 minutes of the reaction, suggesting fast reaction kinetics. Furthermore, raising the solution temperature from 25 °C to 75 °C increased the LREE and HREE recovery from 60% and 32% to 67% and 79%, respectively. The kinetic modeling results demonstrated that the rate-limiting step in the LREE dissolution was diffusion and chemical reaction, whereas the HREE extraction was controlled by only chemical reaction. The leaching study concluded that using 20% S/L at 75 °C for 15 minutes maximized LREE and HREE recovery. The lab-scale precipitation study showed that Fe and Al in solution could be removed at pH 4.5 followed by REE precipitation at pH 6.0 using 6 mol/L NaOH. Finally, the bench-scale data was used to develop a process flowsheet for REE recovery from low-grade bituminous coal sources using acid baking. Finally, based on the proposed flowsheet, a concentrated RE-cake obtained through selective precipitation at pH 6.5 was re-leached using HCl at pH 1.5. The resultant leachate was used to identify the impact of various operating parameters on REE recovery and purity with an aim to maximize REE precipitation efficiency while minimizing the oxalic acid dosage. The operating parameters for this investigation were oxalic acid dosage, iron (III) contamination, solution pH and temperature. The resultant model suggested that oxalic acid dosage and reaction pH are the most significant factors for the REE precipitation efficiency, followed by the interaction of oxalic dosage and Fe concentration. Test results indicated that increasing the oxalic acid concentration from 0g/L to 80g/L improved the REE precipitation efficiency from approximately 4.2% to 95.0%. Furthermore, raising the solution pH from 0.5 to 2.5 considerably enhanced the precipitation efficiency from 0.0% to 98.9%. A solution temperature elevation decreased REE recovery, which indicated an exothermic reaction between REEs and oxalate anions. Finally, a high level of Fe contamination adversely impacted REE precipitation efficiency. The speciation analysis revealed that the dominant iron species in the solution system were Fe-(C₂O₄)₃³⁻, Fe-(C₂O₄)²⁻, and Fe-(C₂O₄)⁺, which consumed the majority of the oxalate anions

rare earth elements, acid baking, high-temperature↗
DOE OSTI2024

Induced Polarization of Clayey Rocks and Soils: Non‐Linear Complex Conductivity Models

Abstract The past decades have witnessed the increased applications of induced polarization (IP) method in the critical zone studies with ubiquitous clay minerals. Although IP outperforms traditional electrical and electromagnetic methods through its unique ability to measure quadrature conductivity, the nonlinearity that quadrature conductivity behaves with salinities and frequencies greatly tortures IP practitioners, as (a) salinity‐dependency makes the quadrature conductivity a varyingly unstable parameter to quantitatively estimate hydraulic properties and clay content; (b) frequency‐dependent Cole‐Cole and Debye/Warburg decomposition models, although mathematically sound, physically mingle the properties of pore water and clay minerals and are empirical in nature. From basic principles, we demonstrate that quadrature conductivity remains a hybrid property involving both clay and water, and develop relevant models to distinguish them. Our models are validated by theories, experiments, simulations, and comparisons, all of which proclaim considerable advantages over previous models and offer the prospect of quantitative applications.

58 GEOSCIENCES↗
DOE OSTI2022

Synthetic antibacterial minerals: harnessing a natural geochemical reaction to combat antibiotic resistance

The overuse of antibiotics in clinical and livestock settings is accelerating the selection of multidrug resistant bacterial pathogens. Antibiotic resistant bacteria result in increased mortality and financial strain on the health care and livestock industry. The development of new antibiotics has stalled, and novel strategies are needed as we enter the age of antibiotic resistance. Certain naturally occurring clays have been shown to have antimicrobial properties and kill antibiotic resistant bacteria. Harnessing the activity of compounds within these clays that harbor antibiotic properties offers new therapeutic opportunities for fighting the potentially devastating effects of the post antibiotic era. However, natural samples are highly heterogenous and exhibit variable antibacterial effectiveness, therefore synthesizing minerals of high purity with reproducible antibacterial activity is needed. Here we describe for the first time synthetic smectite clay minerals and Fe-sulfide microspheres that reproduce the geochemical antibacterial properties observed in natural occurring clays. We show that these mineral formulations are effective at killing the ESKAPE pathogens ( Enterococcus sp., Staphylococcus aureus, Klebsiella pneumoniae, Acinetobacter sp., Pseudomonas aeruginosa and Enterobacter sp.) by maintaining Fe 2+ solubility and reactive oxygen species (ROS) production while buffering solution pH, unlike the application of metals alone. Our results represent the first step in utilizing a geochemical process to treat antibiotic resistant topical or gastrointestinal infections in the age of antibiotic resistance.

58 GEOSCIENCES↗
DOE OSTI2022

Phenomenological Model of Nonlinear Dynamics and Deterministic Chaotic Gas Migration in Bentonite: Experimental Evidence and Diagnostic Parameters

Understanding gas migration in compacted clay materials, e.g., bentonite and claystone, is important for the design and performance assessment of an engineered barrier system of a radioactive waste repository system, as well as many practical applications. Existing field and laboratory data on gas migration processes in low-permeability clay materials demonstrate the complexity of flow and transport processes, including various types of instabilities, caused by nonlinear dynamics of coupled processes of liquid–gas exchange, dilation, fracturing, fracture healing, etc., which cannot be described by classical models of fluid dynamics in porous media. We here show that the complexity of gas migration processes can be explained using a phenomenological concept of nonlinear dynamics and deterministic chaos theory. To do so, we analyzed gas pressure and gas influx (i.e., input) and outflux (i.e., output), recorded during the gas injection experiment in the compact Mx80-D bentonite sample, and calculated a set of the diagnostic parameters of nonlinear dynamics and chaos, such a global embedding dimension, a correlation dimension, an information dimension, and a spectrum of Lyapunov exponents, as well as plotted 2D and 3D pseudo-phase-space strange attractors, based on the univariate influx and outflux time series data. These results indicate the presence of phenomena of low-dimensional deterministic chaotic behavior of gas migration in bentonite. In particular, during the onset of gas influx in the bentonite core, before the breakthrough, the development of gas flow pathways is characterized by the process of chaotic gas diffusion. After the breakthrough, with inlet-to-outlet movement of gas, the prevailing process is chaotic advection. During the final phase of the experiment, with no influx to the sample, the relaxation pattern of gas outflux is resumed back to a process of chaotic diffusion. The types of data analysis and a proposed phenomenological model can be used to establish the basic principles of experimental data-gathering, modeling predictions, and a research design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sorption kinetics and stability of conventional adsorbents for mercury remediation

In-situ remediation of mercury at numerous contaminated sites worldwide is a challenging and costly endeavor due to the persistency of this contaminant. In this study, we evaluated eight commercially available sorbent media ranging from carbon-, clays- and silica-based materials (PBC– Biochar, eSorb – Sorbster, nsPAC – Powdered Activated Carbon, fsPAC – Powdered Activated Carbon with Mackinawite, F300 – Filtrasorb 300, Si-SH – Silica Thiol, eBind – RemBind, Q-Clay – Organoclay PM-199), for their effectiveness in sorbing mercury (Hg 2+ ) and mercury complexed with dissolved organic matter (Hg-DOM). Under the chosen experimental conditions of this study, results showed that in the absence of DOM, the kinetic rates of Hg 2+ sorption onto the evaluated sorbents were in the order of 0.31 min-1 (Si-SH) to 2.98 min -1 (nsPAC), whereas in the presence of DOM, the rates varied from 0.16 min-1 (F300) to 0.95 min -1 (nsPAC). The measured sorption capacity for Hg 2+ in the absence of DOM varied from 3.02 mg/g (Q-Clay) to 35.15 mg/g (Si-SH), whereas in the presence of DOM, calculated partition coefficient (KD) ranged from 69.7 mL/g (Q-Clay) to 41,510 mL/g (Si-SH). Furthermore, kinetic data suggest liquid film diffusion was the rate-limiting steps governing mercury sorption onto the studied media. Overall, the obtained study parameters (kinetics/isotherm) are particularly important in informing robust engineering designs for deployment of the vast majority of evaluated sorbents. Thus, sorbent-based strategies offer viable solutions for cost-effective cleanup of mercury at industrially contaminated sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Weathering Incongruence in Mountainous Mediterranean Climates Recorded by Stream Lithium Isotope Ratios

Lithium isotope ratios (δ 7 Li) of rivers are increasingly serving as a diagnostic of the balance between chemical and physical weathering contributions to overall landscape denudation rates. Here, we show that intermediate weathering intensities and highly enriched stream δ 7 Li values typically associated with lowland floodplains can also describe small upland watersheds subject to cool, wet climates. This behavior is revealed by stream δ 7 Li between +22.4 and +23.5‰ within a Critical Zone observatory located in the Cévennes region of southern France, where dilute stream solute concentrations and significant atmospheric deposition otherwise mask evidence of incongruence. The water-rock reaction pathways underlying this behavior are quantified through a multicomponent, isotope-enabled reactive transport model. Using geochemical characterization of soil profiles, bedrock, and long-term stream samples as constraints, we evolve the simulation from an initially unweathered granite to a steady state weathering profile which reflects the balance between (a) fluid infiltration and drainage and (b) bedrock uplift and soil erosion. Enriched stream δ 7 Li occurs because Li is strongly incorporated into actively precipitating secondary clay phases beyond what prior laboratory experiments have suggested. Chemical weathering incongruence is maintained despite relatively slow reaction rates and moderate clay accumulation due to a combination of two factors. First, reactive primary mineral phases persist across the weathering profile and effectively “shield” the secondary clays from resolubilization due to their greater solubility. Second, the clays accumulating in the near-surface profile are relatively mature weathering byproducts. These factors promote characteristically low total dissolved solute export from the catchment despite significant input of exogenous dust.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Soil properties explain tree growth and mortality, but not biomass, across phosphorus-depleted tropical forests

We observed strong positive relationships between soil properties and forest dynamics of growth and mortality across twelve primary lowland tropical forests in a phosphorus-poor region of the Guiana Shield. Average tree growth (diameter at breast height) increased from 0.81 to 2.1 mm yr -1 along a soil texture gradient from 0 to 67% clay, and increasing metal-oxide content. Soil organic carbon stocks in the top 30cm ranged from 30 to 118 tons C ha -1 , phosphorus content ranged from 7 to 600 mg kg -1 soil, and the relative abundance of arbuscular mycorrhizal fungi ranged from 0 to 50%, all positively correlating with soil clay, and iron and aluminum oxide and hydroxide content. In contrast, already low extractable phosphorus (Bray P) content decreased from 4.4 to <0.0 mg kg -1 in soil with increasing clay content. A greater prevalence of arbuscular mycorrhizal fungi in more clayey forests that had higher tree growth and mortality, but not biomass, indicates that despite the greater investment in nutrient uptake required, soils with higher clay content may actually serve to sustain high tree growth in tropical forests by avoiding phosphorus losses from the ecosystem. Our study demonstrates how variation in soil properties that retain carbon and nutrients can help to explain variation in tropical forest growth and mortality, but not biomass, by requiring niche specialization and contributing to biogeochemical diversification across this region.

54 ENVIRONMENTAL SCIENCES↗