Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Additive-Mixing Fuel Injection (AMFI): A device for robust control and improved performance of high-efficiency LTGC engines

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and particulate emissions. Despite these major advantages, methods for controlling LTGC combustion timing, achieving robust autoignition, and good low-load performance have challenged the development of practical LTGC engines. A key reason is that the ideal reactivity of the fuel varies with operating conditions, with low-reactivity fuels working well at high loads and higher-reactivity fuels working better at low loads. This article introduces a new technique called Additive Mixing Fuel Injection (AMFI) that adjusts the reactivity of the gasoline to obtain good performance over the operating map. Moreover, AMFI can provide robust combustion-timing control because it precisely meters very small amounts (0.01–0.6 mm 3 ) of an ignition-enhancing additive into the fuel each engine cycle. The additive used was 2-ethylhexyl nitrate (EHN), a common, inexpensive diesel-fuel ignition improver, but other additives could be used. Because additive amounts are so small, a 2-gal reservoir would be sufficient for medium-duty applications with refilling only at service intervals of about 8000 mi. The AMFI system has been installed on a single-cylinder LTGC research engine and demonstrated to provide robust combustion-timing control over wide ranges of combustion phasing, fueling rate, intake boost, engine speed, and intake temperature. AMFI also increases the fuel’s reactivity sufficiently to greatly reduce or eliminate the need for charge heating, simplifying engine design and significantly increasing thermal efficiency and the maximum load at low-boost conditions. The nitrogen in the EHN produced a modest increase in NOx, but it was mitigated by lower intake temperatures, and NOx emissions remained very low. Finally, the additive increases the sensitivity of autoignition reactions to variations in the local fuel/air mixture within the charge. This allows the use of controlled fuel stratification for improved LTGC-engine performance, and its potential to improve low-load operation was demonstrated.

Dec, John E.↗

2015 Summer Design Challenge: Team A&E (2241) Additively Manufactured Discriminator.

Current discriminator designs are based on historical designs and traditional manufacturing methods. The goal of this project was to form non-traditional groups to create novel discriminator designs by taking advantage of additive manufacturing. These designs would expand current discriminator designs and provide insight on the applicability of additive manufacturing for future projects. Our design stretched the current abilities of additive manufacturing and noted desired improvements for the future. Through collaboration with NSC, we noted several additional technologies which work well with additive manufacturing such as topology optimization and CT scanning and determined how these technologies could be improved to better combine with additive manufacturing.

42 ENGINEERING↗

Additively Manufactured, Net Shape Powder Metallurgy Cans for Valves Used in Energy Production

Additive manufacturing (AM) has the potential to enable a paradigm shift in fabricating complex net shape components with yields over 90%, significantly increasing productivity, decreasing energy consumption during manufacturing and improving downstream energy efficiency. ORNL has developed a technology for producing large-scale additively manufactured polymer matrix composite components at deposition rates on the order of 100 lbs. per hour. This project utilized tools, dies and molds made from this technology to enable the net shape forming of cans for the powder metallurgy (PM) manufacturing of valves used in energy production plants. This approach has the potential to develop affordable valves with superior performance to castings. It will also lead to increased strength values, decreased wall thickness size, and the potential for higher yields (less machining). This project is critical for evaluating new methodologies for the fabrication of additively manufactured tooling, molds and dies that could be used across multiple industries. In the first phase of this project, a new methodology of creating a Powder Metallurgy and Hot Isostatic Pressing (PM-HIP) container by hydroforming sheet metal over additively manufactured (AM) dies was evaluated. The goal in this stage of development was to evaluate some of the new polymer matrix composite materials designed for deposition on large scale additive manufacturing systems as candidates for hydroforming steel and aluminum sheet to make thin gauge net shape components. In order to meet this objective, most research was performed on subscale tools in order to evaluate the processing pressures, material options, and gauge thicknesses most relevant to this approach. In addition, full scale AM tools (30% over final component geometry) were produced to demonstrate scalability, but were not used in testing. The first phase of this project has proven this concept has merit, but future studies are required to address minor tool failures that occurred in phase one due to geometry, cost of the process over other techniques, and demonstration of a full-scale tool that could then be used in (HIP). Lastly, this project provides the PM community a new approach in using hydroforming for the manufacturing of cans, a process that was not highly utilized for this purpose previously.

42 ENGINEERING↗

Additive Manufacturing Design Guidelines for Wind Industry

The purpose of this report is to equip wind industry professionals with the fundamental information needed to best leverage additive manufacturing techniques in their design and manufacturing decisions. Herein an overview of each of the seven families of additive manufacturing is provided, along with typical materials used in each process, current ranges on process speeds, materials and system costs, and examples of systems on the market today. Using the lens of large-scale additive to suit the needs of the wind industry, the processes that are well-suited to large-scale production are down selected from the seven families and additional information with design guidelines specific to each process are detailed. A companion document titled “Relevant Additive Manufacturing Materials for Wind Industry” elaborates on the specifics of relevant material properties and test methods for additive manufacturing materials.

17 WIND ENERGY↗

Additives in Localized High Concentration Electrolytes for Safe Lithium-Ion Batteries

In this work, the effects of various additives in a localized high concentration electrolyte (LHCE) on the cycling performance of lithium (Li)-ion batteries were studied. The LHCEs utilize trimethyl phosphate as a flame-retarding solvent and 1H,1H,5H-octafluoropentyl 1,1,2,2-tetrafluoroethyl ether as a medium-high flash point diluent, for the purpose to reduce the electrolyte flammability and improve the battery safety, which are not possessed by the conventional electrolytes of LiPF 6 in organic carbonates due to their high flammability. The LHCEs have unique solvation structure which enables the use of flame-retardant solvents to greatly decrease the electrolyte flammability as well as enhance the battery cycling stability. However, the additives added in the LHCEs result in different battery performances. The organic carbonate additives largely reduce the initial capacities although the cell capacity can be partially recovered with cycling. The two phosphate salt additives behave better than the organic carbonate additives in terms of cell capacity and cycling stability. More cell performance evaluation will be conducted and the detailed characterization will be performed to investigate the root causes of different behaviors of additives in the LHCEs on battery performances.

25 ENERGY STORAGE↗

Additive Technology in Optimal Synthesis of Individual Vehicle Components and Mechanisms

Experience in optimal synthesis of individual vehicle components and mechanisms on the basis of additive technology is analyzed. A list of basic additive technologies is presented. The benefits of additive technology in combination with three-dimensional computer simulation are noted. The possibility of visualizing CAE calculations by means of additive technology is considered. In addition, the role of additive technology in the manufacture of individual vehicle components and mechanisms is discussed.

42 ENGINEERING↗

Additive-mixing fuel-injection system for internal combustion engines

A system and method for fast control of the timing of combustion in an internal combustion engine, comprising actuating a fast-acting fuel-additive supply valve to meter a variable amount of fuel additive into a fuel stream, thereby forming an additive-enhanced fuel with an additive concentration that can be dynamically adjusted as fast as each engine cycle; injecting the additive-enhanced fuel directly or indirectly into a combustion chamber or into an intake port; and combusting the additive-enhanced fuel.

42 ENGINEERING↗

Methods and apparatus for embedding heating circuits into articles made by additive manufacturing and articles made therefrom

Methods of embedding a heating circuit in an article fabricated by additive manufacturing. The methods describe techniques such as co-extruding a wire, capable of being heated, along with print material in additive manufacturing of the article, and placing a pre-shaped wire capable of being heated between adjacent layers of the article. A third method includes dispensing a wire, capable of being heated, during the additive manufacturing of the article, and compacting the wire into the printed material. An apparatus for embedding a heating circuit in an article fabricated by additive manufacturing. The apparatus contains a wire dispenser, a cutter to control the length of the wire dispensed, and a compactor capable of embedding the wire capable of being heated into the printed material. An article made by additive manufacturing is disclosed. The article contains at least one heating element embedded in the article during the additive manufacturing process.

Barocio, Eduardo↗

High performance, rapid thermal/UV curing epoxy resin for additive manufacturing of short and continuous carbon fiber epoxy composites

An additive manufacturing resin system includes a container; a build platform in the container; a build platform drive; an additive manufacturing resin that forms an additive manufacturing resin bath; an additive manufacturing print head; a build material supply connected to the additive manufacturing print head; an infill resin in the container, wherein the infill resin is supported by the additive manufacturing resin bath; a computer controller; and an extruded material that forms the product, wherein the infill resin at least partially surrounds the extruded material that forms the product. An infill resin supply provides the infill resin into the container and a control valve is connected to the infill resin supply. An IR light sensor is connected to the control valve and operatively connected to the infill resin in the container.

Lewicki, James↗

Design and Experimental Demonstration of an Additive Manufactured Smart Oxy-Methane Burner for High Pressure and Supercritical Combustion

Pressurized oxy combustion-based systems can improve efficiency by recovering latent heat of the steam in the Flue Gas and achieving 90% CO2 capture. In addition, the novel Directly Heated Supercritical Carbon Dioxide (DH-SCO2) power cycles can achieve high thermal efficiencies and provide nearly full carbon capture. Additionally, due to the reduction of flue gas at higher pressure, smaller system size and capital cost reductions are also possible. Recent thermodynamic analysis of the DH-SCO2 cycle performed by the UTEP research team shows that combustion conditions in the vicinity of 300 bar pressure and 1000-1400 K temperature allow for relatively high system efficiencies while operating within the limit of available combustor materials. However, the realization of a directly heated supercritical power cycle requires combustion systems to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 K). The thermodynamic properties along with the combustion properties and kinetics are unexplored at such conditions. Additionally, the interaction of the supercritical environment with energy components is also unknown. High-pressure combustion tests are performed using a smart burner at some intermediate pressure ranges (<20 bar) to help minimize these knowledge gaps. The knowledge obtained from the high-pressure test will assist in understanding the combustion chamber pressurization mechanism, ignition and flame behavior at the elevated pressure. The obtained data will act as a systematic first step in testing at higher pressures of 100 and 300 bar pressures.The primary purpose of this Dissertation is to demonstrate the operability of a low NOx smart burner for oxy-methane combustion at high pressure (< 20 bar) and scalable up to supercritical conditions. A shear co-axial smart burner is designed with a real-time temperature monitoring capability to understand the burner face interaction at high-pressure conditions. In addition, the burner has four independent injection ports to allow the independent injection of fuel and dilution gases in the combustor. The maximum operating capability of the burner is 575 kWth. The burner was fabricated using a Laser Powder Bed Fusion process with Nickel Alloy 718. A powder removal technology was invented comprising ultrasonic vibration, liquid nitrogen exposure and media blasting to remove powders from internal channels of the burner. The burner operability tests are performed in the high-pressure combustor and the swirl combustor. The high-pressure combustor was used to investigate the burner operability and thermal soak back at different pressurized conditions. The experimental tests in high-pressure combustor up to 275 kWth input resulted in 16.5 bar chamber pressure and 198°C thermal soaks back to the burner. The burner was capable of providing the required thermal input within a 3% deviation range. In addition, soot formation occurred at high-pressure tests. The swirl combustor was used to observe the flame stability of the burner. Flame lift-off was observed for jet velocities above 450 m/s. Additionally, lift-off decreased for low co-flow velocities. CO2 dilution experiments showed increased flame instabilities for all conditions above 50% dilution ratios. At lower thermal inputs, partial flame blow-offs occurred for dilution ratios above 50%. All conditions significantly reduced the flame temperature and increased the flame lift-off height. Finally, a 2nd generation AM smart burner was designed using the knowledge from the 1st generation burner experiments. The 2nd generation burner incorporated two sets of swirlers with 0.9 swirl no. A cooling system was also designed for long-duration tests at higher pressures. The thermal input and division of the burner's power are kept the same as the 1st generation burner. The burner is to be fabricated using nickel-alloy 718 for high-pressure handling capability. The design can sustain at high-pressure conditions up to 100 bar.

Islam, Md Nawshad Arslan↗

ADDITIVELY MANUFACTURED SURFACE HEAT TRANSFER ENHANCEMENTS FOR THE TRANSFORMATIONAL CHALLENGE REACTOR

The Transformational Challenge Reactor (TCR) is a high-temperature gas-cooled reactor design that uses additively manufactured fuel elements. TCR fuel elements have walls made of silicon carbide and are filled with tristructural-isotropic fuel particles. These fuel elements can have radically different shapes and integrated features than existing designs due to the reduced cost for complex structures in binder jet additive manufacturing. As such, binder jet additive manufacturing enables wall surface features to be embedded that can deliver superior heat transfer performance than smooth wall designs. In this work, the authors conducted a computational fluid dynamics study to evaluate selected wall features integrated into TCR fuel elements. Results show that surface features can outperform smooth wall designs; however, there are unique challenges for gas-cooled reactor core designs that have not been fully explored by previous research. For example, the rough surface finish and process variability of ceramics additive manufacturing make it challenging to predict surface roughness effects before fabrication. Additionally, the small hydraulic diameters of coolant channels in reactor cores make it difficult to engineer surface features that do not significantly increase the pressure drop. Engineers must carefully size surface features for heat transfer enhancement in additive fuel elements to operate above the base material's surface roughness effects and below the coolant channel size.

Weinmeister, Justin↗

3D printing of additive structures for nuclear fuels

A method for manufacturing a nuclear fuel compact is provided. The method includes forming an additive structure, consolidating a fuel matrix around the additive structure, and thermally processing the fuel matrix to form a fuel compact in which the additive structure is encapsulated therein. The additive structure optionally includes a vertical segment and a plurality of arm segments that extend generally radially from the vertical segment for conducting heat outwardly toward an exterior of the fuel compact. In addition to improving heat transfer, the additive structure may function as burnable absorbers, and may provide fission product trapping.

Terrani, Kurt A.↗

3D printing of additive structures for nuclear fuels

A method for manufacturing a nuclear fuel compact is provided. The method includes forming an additive structure, consolidating a fuel matrix around the additive structure, and thermally processing the fuel matrix to form a fuel compact in which the additive structure is encapsulated therein. The additive structure optionally includes a vertical segment and a plurality of arm segments that extend generally radially from the vertical segment for conducting heat outwardly toward an exterior of the fuel compact. In addition to improving heat transfer, the additive structure may function as burnable absorbers, and may provide fission product trapping.

Terrani, Kurt A.↗

Impacts of an additional exhaust shaft on WIPP performance - 15170

The Waste Isolation Pilot Plant (WIPP), located in southeastern New Mexico, has been developed by the U.S. Department of Energy (DOE) for the geologic (deep underground) disposal of transuranic (TRU) waste. WIPP performance assessment (PA) demonstrates repository performance from facility closure to 10,000 years after closure. The recent radiological release event at the WIPP site has temporarily halted waste emplacement activities at the facility. A modified ventilation system is envisioned that will provide sufficient airflow necessary for the resumption of full-rate disposal operations in the future. A primary component of the modified ventilation system is an additional exhaust shaft in the north end of the repository. There are four shafts currently in the repository north end, namely a salt handling shaft, an exhaust shaft, a waste shaft, and an air intake shaft. These shafts are combined into a single composite shaft in WIPP PA that captures the combined impacts of all of them. The proposed additional exhaust shaft is combined with the four existing shafts in the repository model to determine its impacts on long-term repository performance. Moreover, mined volume in the repository north end is modified in the repository representation so as to include additional drifts created to access the new shaft. Computed gas and brine flow behaviors corresponding to the repository with the additional exhaust shaft are compared to those obtained in the PA executed for the 2014 Compliance Re-certification Application (the CRA-2014 PA). Results show that the repository with an additional exhaust shaft and drifts yields brine and gas flow behaviors similar to the current repository configuration. It is concluded that WIPP continues to satisfy regulatory compliance limits with the addition of an exhaust shaft and its access drifts, with compliance curves like those found in the CRA-2014 PA for total normalized releases. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Methods and apparatus for embedding heating circuits into articles made by additive manufacturing and articles made therefrom

Methods of embedding a heating circuit in an article fabricated by additive manufacturing. The methods describe techniques such as co-extruding a wire, capable of being heated, along with print material in additive manufacturing of the article, and placing a pre-shaped wire capable of being heated between adjacent layers of the article. A third method includes dispensing a wire, capable of being heated, during the additive manufacturing of the article, and compacting the wire into the printed material. An apparatus for embedding a heating circuit in an article fabricated by additive manufacturing. The apparatus contains a wire dispenser, a cutter to control the length of the wire dispensed, and a compactor capable of embedding the wire capable of being heated into the printed material. An article made by additive manufacturing is disclosed. The article contains at least one heating element embedded in the article during the additive manufacturing process.

Barocio, Eduardo↗

DEVELOPMENT OF INEXPENSIVE HIGH TEMPERATURE NITI-BASED SHAPE MEMORY ALLOYS FOR POWDER BED ADDITIVE MANUFACTURING

NiTi and NiTi-based Shape Memory Alloys (SMA) exhibit a reversible solid-state phase transformation from martensite to austenite driven by thermal energy. High temperature (Mf>100°C) SMAs are martensite at room temperature and can be fabricated into solid-state actuators that return to a pre-programmed shape against a designed load after heating to transformation threshold. Reactive as-fabricated additively manufactured parts (4-D printing) is the current state of the art in manufacturing of SMAs but requires compositions compliant to rapid solidification. Existing actuator designs are developed from commercially available, highly investigated material compositions. However, existing high temperature high performance (high actuation strain, low thermal hysteresis) shape memory alloys contain significant (>10% at.) portions of high-cost Platinum Group Metals (PGMs). It is of significant scientific interest to investigate material compositions that are peer performing or superior to PGMs whose constituent elements represent a significant cost savings. Shape memory alloy properties vary significantly with small (0.1% at.) compositional changes making robust investigative sample sets very large. Computational material design can be deployed to shrink the compositional space of possible alloy combinations and reduce the experimental load in material discovery. Investigating shape memory effect (SME) and validating process additive process parameters for a single novel composition is cost intensive in both time and consumed materials. Additionally, sub-optimal processing, oxygen, or solidification rate sensitivity could render additively manufacturing specimens without micro, macro cracks, or significant chemical variance impossible. Unfortunately, such failure susceptibility cannot be simulated. Therefore, a research pathway to validate novel shape memory alloy compositions for powder bed fusion additive manufacturing without the need for powdered feedstock is also proposed. This research investigates novel high temperature shape memory alloys for actuators without platinum group alloying elements to discover one that could be commercially viable as an additive manufacturing feedstock.

Sundermann, Tayler↗

Dimolybdenum Paddlewheel Complexes with Cation Binding Sites as Electrolyte Additives to Manipulate the Solid-Electrolyte Interphase at Lithium Metal Anodes

The use of electrolyte additives at millimolar loadings to control the surface chemistry of lithium metal anodes (LMAs) is a leading strategy to improve lithium metal batteries and promote electrosynthetic reactions. Whereas previous studies employed either inorganic or organic additives, in this study, we report the first organometallic additive, Mo 2 (mea) 4 [1, mea = 2-(2-methoxyethoxy)acetate], a dimolybdenum paddlewheel complex that is stable under Li plating conditions and features cation binding sites in the second coordination sphere that promote reversible Li + coordination. Binding of Li + ions to 1 induces immobilization of cationically charged aggregates (or products thereof) into the solid electrolyte interphase (SEI), imparting multiple beneficial functions. The modified SEI was found to protect the LMA against parasitic side reactions, produce modest but measurable improvements to Li plating properties (e.g., overpotential, surface structure, and Coulombic efficiency), and improve interfacial charge transport properties. Furthermore, the most notable benefit to battery cycling performance appears in calendar aging tests, which show that the presence of the additive protects the LMA from parasitic side reactions that would otherwise decrease overall cell cycling efficiency over time. Collectively, these data disclose a tactic for designing electrolyte additives using principles of organometallic synthesis.

Additives↗

Influence of dual nitrogen and phosphorus additions on nutrient uptake and saturation kinetics in a forested headwater stream

Nitrogen (N) and phosphorus (P) can limit autotrophic and heterotrophic metabolism in lotic ecosystems, yet most studies that evaluate biotic responses to colimitation focus on patch-scale (e.g., nutrient diffusing substrata) rather than stream-scale responses. In this study, we evaluated the effects of single and dual N and P additions on ambient nutrient uptake rates and saturation kinetics during two biologically contrasting seasons (spring, autumn) in Walker Branch, a temperate forested headwater stream in Tennessee, USA. In each season, we used separate instantaneous pulse additions to quantify nutrient uptake rates and saturation kinetics of N (nitrate) and P (phosphate). We then used steady-state injections to elevate background stream water concentrations (to low and then high background concentrations) of one nutrient (e.g., N) and released instantaneous pulses of the other nutrient (e.g., P). We predicted that elevating the background concentration of one nutrient would result in a lower ambient uptake length and a higher maximum areal uptake rate of the other nutrient in this colimited stream. Our prediction held true in spring, as maximum areal uptake rate of N increased with elevated P concentrations from 185 µg m –2 min –1 (no added P) to 354 µg m –2 min –1 (high P). This pattern was not observed in autumn, as uptake rates of N were not measurable when P was elevated. Further, elevating background N concentration in either season did not significantly increase P uptake rates, likely because adsorption rather than biotic uptake dominated P dynamics. Laboratory P sorption assays demonstrated that Walker Branch sediments had a high adsorption capacity and were likely a sink for P during most pulse nutrient additions. Furthermore, it may be difficult to use coupled pulse nutrient additions to evaluate biotic uptake of N and P in streams with strong P adsorption potential. Future efforts should use dual nutrient addition techniques to investigate reach-scale coupled biogeochemical cycles (C–N–P, and other elemental cycles [e.g., Fe, Mo]) across seasons, biomes, and land-use types and over longer time periods.

54 ENVIRONMENTAL SCIENCES↗