Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “windmill”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

The sail wing windmill and its adaptation for use in rural India

An 8 meter-diameter prototype sail wing windmill is reported that uses a one meter-diameter bullock cartwheel to which three bamboo poles are latched in a triangular pattern with overlapping ends, to form the airframe for cloth sails. This device lifts 300 pounds to a height of 20 feet in one minute in a 10 mph wind.

Sherman, M. M.↗

How big is a windmill - Glauert revisited

The obvious similarities to propellers and helicopter rotors suggest that helicopter technology might be used to improve wind generator performance, perhaps including development of a windmill airfoil. In a back-to-basics approach, this paper reviews the analyses of Glauert to determine basic size-power relations. The energy method of Wheatley developed for helicopter/auto-gyro performance prediction is then incorporated into the basic theory. Equations and charts are presented showing ratios of power output to the ideal power capability as functions of mean blade lift and drag coefficients, solidity and rotor tip speed ratio. It is found there is little possibility for improved performance by using improved airfoils. The basic assumptions of the Glauert theory are reviewed and means are suggested for achieving the basic power capability indicated by momentum theory.

Mccloud, J. L., III↗

The hydraulic windmill

An hydraulic windmill is described. It pumps pressurized oil from rotor shaft level to the ground where a motor generator produces electricity. Alternatively, the useful output may be heat. Rotor speed is governed by a flow valve. Over pressure, the result of high wind velocity, rotates the tail to move the rotor blades out-of-the-wind. Loss of oil pressure causes a brake to close as well as to swing the tail to its maximum distance from the rotor plane.

Browing, J. A.↗

Vertical shaft windmill

A vertical shaft has several equally spaced blades mounted. Each blade consists of an inboard section and an outboard section skew hinged to the inboard section. The inboard sections automatically adjust their positions with respect to the fixed inboard sections with changes in velocity of the wind. This windmill design automatically governs the maximum rotational speed of shaft.

Grana, D. C.↗

Hinged-Blade, Vertical-Shaft Windmill

Vertical-shaft windmill concept calls for hinged, flapping blades to increase energy-conversion efficiency by reducing wind-energy loss. Hinged Blade Halves unfold to catch wind when moving with it, then fold away from wind when moving against it.

Shultz, B., Jr.↗

Cable suspended windmill

A windmill is disclosed which includes an airframe having an upwind end and a downwind end. The first rotor is rotatably connected to the airframe, and a generator is supported by the airframe and driven by the rotor. The airframe is supported vertically in an elevated disposition by poles which extend vertically upwardly from the ground and support cables which extend between the vertical poles. Suspension cables suspend the airframe from the support cable.

Farmer, Moses G.↗

General theory of windmills

In this paper the application of the slip curve method to the design and analysis of windmills is discussed and illustrated by example.

Munk, Max M↗

Wind-driven propellers (or "windmills")

Wind-driven propellers are much used as sources of power for equipment such as radios. This report establishes the principles involved and acquaints the reader with rules for design of such windmills.

GENERATORS, FANS↗

Altitude-wind-tunnel investigation of Westinghouse 19B-2, 19B-8, and 19XB-1 jet-propulsion engines III : performance and windmilling drag characteristics

The performance characteristics of the 19B-8 and 19XB-1 turbojet engines and the windmilling drag characteristics of the 19B-8 engine were determined in the NACA Cleveland altitude wind tunnel. The 19B engine is one of the earliest experimental Westinghouse axial-flow engines. The 19XB-1 engine is an experimental prototype of the Westinghouse 19XB series, having a rated thrust of 1400 pounds. Improvements in performance and operational characteristics have resulted in the 19XB-2B engine with a rated thrust of 1600 pounds. The investigations were conducted on the 19B-8 engine at simulated altitudes from 5000 to 25,000 feet with various free-stream ram-pressure ratios and on the 19XB-1 engine at simulated altitudes from 5000 to 30,000 feet with approximately static free-stream conditions. Data for these two engines are presented to show the effect of altitude, free-stream ram-pressure ratio, and tail-pipe-nozzle area on engine performance.

Fleming, William A↗

Preliminary Results of an Altitude-Wind-Tunnel Investigation of a TG-100A Gas Turbine-Propeller Engine II - Windmilling Characteristics

An investigation was conducted to determine the operational and performance characteristics of the TG-100A gas turbine-propeller engine II. Windmilling characteristics were deterined for a range of altitudes from 5000 to 35,000 feet, true airspeeds from 100 to 273 miles per hour, and propeller blade angles from 4 degrees to 46 degrees.

Conrad, E. W.↗

Altitude-Wind-Tunnel Investigation of a 4000-Pound-Thrust Axial-Flow Turbojet Engine: Performance and Windmilling Drag Characteristics - Part 1

The results of altitude-wind-tunnel tests conducted to determine the performance of an axial-flow-type 4000.pound-thrust turboJet engine for a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.02 to 1.86 are presented and the experimental and analytical methods employed are discussed. By means of suitable generalizing factors applied to the measured performance data, curves were obtained from which the engine performance at any altitude for a given ram pressure ratio can be estimated. The data presented include the windmilling drag characteristics of the turbojet engine for the ranges of altitudes and ram pressure ratios covered by the performance data.

Fleming, William A.↗

Detail Calculations of the Estimated Shift in Stick-Fixed Neutral Point Due to the Windmilling Propeller and to the Fuselage of the Republic XF-12 Airplane

Detail calculations are presented of the shifts in stick-fixed neutral point of the Republic XF-12 airplane due to the windmilling propellers and to the fuselage. The results of these calculations differ somewhat from those previously made for this airplane by Republic Aviation Corporation personnel under the direction of Langley flight division personnel. Due to these differences the neutral point for the airplane is predicted to be 37.8 percent mean aerodynamic chord, instead of 40.8 percent mean aerodynamic chord as previously reported.

White, M. D.↗

Flight Test of the Lateral Stability of a 0.133-Scale Model of the Convair XFY-1 Airplane with Windmilling Propellers at Mach Numbers from 0.70 to 1.12 (TED No. NACA DE 369)

A flight test of a rocket-propelled model of the Convair XFY-1 airplane was conducted to determine the lateral stability and control characteristics, The 0.133-scale model had windmilling propellers for this test, which covered a Mach number range of O.70 to 1.12. The center of gravity was located at 13.9 percent of the mean aerodynamic chord. The methods of analysis included both a solution by vector diagrams and simple one- and two-degree-of-freedom methods. The model was both statically and dynamically stable throughout the speed range of the testa The roll damping was good, and the slope of the side-force curve varied little with speed. The rudder was effective throughout the test speed range, although it was reduced to about 43 percent of its subsonic value at supersonic speeds.

Hollinger, James A.↗

Application of IDT sensors for structural health monitoring of windmill turbine blades made of composite material

Interdigital transducers (IDT) generate and receive ultrasonic surface waves without the complexity involved with secondary devices such as angled wedges or combs. The IDT sensors have been successfully applied for the NDE of homogeneous materials like metals in order to detect cracks and de-bond. However, these transducers have not been yet adapted for complex and anisotropic materials like fiber-reinforced composites. This work presents the possibility of using IDT sensors for monitoring structural damages in wind turbine blades, typically made of fiberglass composites. IDT sensors with a range of operating frequency between 250 kHz and 1 MHz are initially tested on representative composite test panels for ultrasonic surface wave properties including beam spread, propagation distance and effect of material's anisotropy. Based on these results, an optimum frequency range for the IDT sensor is found to be 250-500 kHz. Subsequently, IDT sensors with operating frequency 500 kHz are used to detect and quantify artificial defects created in the composite test samples. Discussions are made on the interaction of ultrasonic fields with these defects along with the effects of fiber directionality and composite layer stacking.

42 ENGINEERING↗