Results for “voids” — Page 2

NASA NTRS1996

Intergalactic Hydrogen Clouds at Low Redshift: Connections to Voids and Dwarf Galaxies

We provide new post-COSTAR data on one sightline (Mrk 421) and updated data from another (I Zw 1) from our Hubble Space Telescope (HST) survey of intergalactic Ly(alpha) clouds located along sightlines to four bright quasars passing through well-mapped galaxy voids (16000 km/s pathlength) and superclusters (18000 km/s). We report two more definite detections of low-redshift Ly(alpha) clouds in voids: one at 3047 km/s (heliocentric) toward Mrk 421 and a second just beyond the Local Supercluster at 2861 km/s toward I Zw 1, confirming our earlier discovery of Ly(alpha) absorption clouds in voids (Stocke et al., ApJ, 451, 24). We have now identified ten definite and one probable low-redshift neutral hydrogen absorption clouds toward four targets, a frequency of approximately one absorber every 3400 km/s above 10(exp 12.7/sq cm column density. Of these ten absorption systems, three lie within voids; the probable absorber also lies in a void. Thus, the tendency of Ly(alpha) absorbers to 'avoid the voids' is not as clear as we found previously. If the Ly(alpha) clouds are approximated as homogeneous spheres of 100 kpc radius, their masses are approximately 10(exp 9)solar mass (about 0.01 times that of bright L* galaxies) and they are 40 times more numerous, comparable to the density of dwarf galaxies and of low-mass halos in numerical CDM simulations. The Ly(alpha) clouds contribute a fraction Omega(sub cl)approximately equals 0.003/h(sub 75) to the closure density of the universe, comparable to that of luminous matter. These clouds probably require a substantial amount of nonbaryonic dark matter for gravitational binding. They may represent extended haloes of low-mass protogalaxies which have not experienced significant star formation or low-mass dwarf galaxies whose star formation ceased long ago, but blew out significant gaseous material.

Shull, J. Michael↗

NASA NTRS1985

Reliability of void detection in structural ceramics using scanning laser acoustic microscopy

The reliability of scanning laser acoustic microscopy (SLAM) for detecting surface voids in structural ceramic test specimens was statistically evaluated. Specimens of sintered silicon nitride and sintered silicon carbide, seeded with surface voids, were examined by SLAM at an ultrasonic frequency of 100 MHz in the as fired condition and after surface polishing. It was observed that polishing substantially increased void detectability. Voids as small as 100 micrometers in diameter were detected in polished specimens with 0.90 probability at a 0.95 confidence level. In addition, inspection times were reduced up to a factor of 10 after polishing. The applicability of the SLAM technique for detection of naturally occurring flaws of similar dimensions to the seeded voids is discussed. A FORTRAN program listing is given for calculating and plotting flaw detection statistics.

Roth, D. J.↗

NASA NTRS1985

Probability of detection of internal voids in structural ceramics using microfocus radiography

The reliability of microfocus x-radiography for detecting subsurface voids in structural ceramic test specimens was statistically evaluated. The microfocus system was operated in the projection mode using low X-ray photon energies (20 keV) and a 10 micro m focal spot. The statistics were developed for implanted subsurface voids in green and sintered silicon carbide and silicon nitride test specimens. These statistics were compared with previously-obtained statistics for implanted surface voids in similar specimens. Problems associated with void implantation are discussed. Statistical results are given as probability-of-detection curves at a 95 percent confidence level for voids ranging in size from 20 to 528 micro m in diameter.

Baaklini, G. Y.↗

NASA NTRS1986

Reliability of scanning laser acoustic microscopy for detecting internal voids in structural ceramics

The reliability of 100 MHz scanning laser acoustic microscopy (SLAM) for detecting internal voids in sintered specimens of silicon nitride and silicon carbide was evaluated. The specimens contained artificially implanted voids and were positioned at depths ranging up to 2 mm below the specimen surface. Detection probability of 0.90 at a 0.95 confidence level was determined as a function of material, void diameter, and void depth. The statistical results presented for void detectability indicate some of the strengths and limitations of SLAM as a nondestructive evaluation technique for structural ceramics.

Roth, D. J.↗

NASA NTRS1986

Quantitative void characterization in structural ceramics using scanning laser acoustic microscopy

The ability of scanning laser acoustic microscopy (SLAM) to characterize artificially seeded voids in sintered silicon nitride structural ceramic specimens was investigated. Using trigonometric relationships and Airy's diffraction theory, predictions of internal void depth and size were obtained from acoustic diffraction patterns produced by the voids. Agreement was observed between actual and predicted void depths. However, predicted void diameters were generally much greater than actual diameters. Precise diameter predictions are difficult to obtain due to measurement uncertainty and the limitations of 100 MHz SLAM applied to typical ceramic specimens.

Roth, D. J.↗

NASA NTRS1986

Reliability of void detection in structural ceramics by use of scanning laser acoustic microscopy

The reliability of scanning laser acoustic microscopy (SLAM) for detecting surface voids in structural ceramic test specimens was statistically evaluated. Specimens of sintered silicon nitride and sintered silicon carbide, seeded with surface voids, were examined by SLAM at an ultrasonic frequency of 100 MHz in the as fired condition and after surface polishing. It was observed that polishing substantially increased void detectability. Voids as small as 100 micrometers in diameter were detected in polished specimens with 0.90 probability at a 0.95 confidence level. In addition, inspection times were reduced up to a factor of 10 after polishing. The applicability of the SLAM technique for detection of naturally occurring flaws of similar dimensions to the seeded voids is discussed. A FORTRAN program listing is given for calculating and plotting flaw detection statistics.

Roth, D. J.↗

NASA NTRS1986

Reliability of scanning laser acoustic microscopy for detecting internal voids in structural ceramics

The reliability of 100 MHz scanning laser acoustic microscopy (SLAM) for detecting internal voids in sintered specimens of silicon nitride and silicon carbide was evaluated. The specimens contained artificially implanted voids and were positioned at depths ranging up to 2 mm below the specimen surface. Detection probability of 0.90 at a 0.95 confidence level was determined as a function of material, void diameter, and void depth. The statistical results presented for void detectability indicate some of the strengths and limitations of SLAM as a nondestructive evaluation technique for structural ceramics.

Roth, D. J.↗

NASA NTRS1986

Probability of detection of internal voids in structural ceramics using microfocus radiography

The reliability of microfocous X-radiography for detecting subsurface voids in structural ceramic test specimens was statistically evaluated. The microfocus system was operated in the projection mode using low X-ray photon energies (20 keV) and a 10 micro m focal spot. The statistics were developed for implanted subsurface voids in green and sintered silicon carbide and silicon nitride test specimens. These statistics were compared with previously-obtained statistics for implanted surface voids in similar specimens. Problems associated with void implantation are discussed. Statistical results are given as probability-of-detection curves at a 95 precent confidence level for voids ranging in size from 20 to 528 micro m in diameter.

Baaklini, G. Y.↗

NASA NTRS1987

Quantitative void characterization in structural ceramics by use of scanning laser acoustic microscopy

The ability of scanning laser acoustic microscopy (SLAM) to characterize artificially seeded voids in sintered silicon nitride structural ceramic specimens was investigated. Using trigonometric relationships and Airy's diffraction theory, predictions of internal void depth and size were obtained from acoustic diffraction patterns produced by the voids. Agreement was observed between actual and predicted void depths. However, predicted void diameters were generally much greater than actual diameters. Precise diameter predictions are difficult to obtain due to measurement uncertainty and the limitations of 100 MHz SLAM applied to typical ceramic specimens.

Roth, D. J.↗

NASA NTRS1991

The full-scale process and design changes for elimination of insulation edge separations and voids in tang flap area

Qualification of the full-scale process and design changes for elimination of redesigned solid rocket motor tang nitrile butadiene rubber insulation edge separations and voids was performed from 24 March to 3 December 1990. The objectives of this test were: to qualify design and process changes on flight hardware using a tie ply between the redesigned solid rocket motor steel case and the nitrile butadiene rubber insulation over the tang capture features; to qualify the use of methyl ethyl ketone in the tang flap region to reduce voids; and to determine if holes in the separator film reduce voids in the tang flap region. The tie ply is intended to aid insulation flow during the insulation cure process, and thus reduce or eliminate edge unbonds. Methyl ethyl ketone is intended to reduce voids in the tang flap area by providing better tacking characteristics. The perforated film was intended to provide possible vertical breathe paths to reduce voids in the tang area. Tang tie ply testing consisted of 270 deg of the tang circumference using a new layup method and 90 deg of the tang circumference using the current layup methods. Tie ply process success was defined as a reduction of insulation unbonds. Lack of any insulation edge unbonds on the tang area where the new process was used, and the presence of 17 unbonds with the current process, proves the test to be a success. Successful completion of this test has qualified the new processes.

Danforth, Richard A.↗

NASA NTRS1992

An initial study of void formation during solidification of aluminum in normal and reduced-gravity

Void formation due to volumetric shrinkage during aluminum solidification was observed in real time using a radiographic viewing system in normal and reduced gravity. An end chill directional solidification furnace with water quench was developed to solidify aluminum samples during the approximately 16 seconds of reduced gravity (+/- 0.02g) achieved by flying an aircraft through a parabolic trajectory. Void formation was recorded for two cases: first a nonwetting system; and second, a wetting system where wetting occurs between the aluminum and crucible lid. The void formation in the nonwetting case is similar in normal and reduced gravity, with a single vapor cavity forming at the top of the crucible. In the wetting case in reduced gravity, surface tension causes two voids to form in the top corners of the crucible, but in normal gravity only one large voids forms across the top.

Chiaramonte, Francis P.↗

NASA NTRS1992

The void spectrum in two-dimensional numerical simulations of gravitational clustering

An algorithm for deriving a spectrum of void sizes from two-dimensional high-resolution numerical simulations of gravitational clustering is tested, and it is verified that it produces the correct results where those results can be anticipated. The method is used to study the growth of voids as clustering proceeds. It is found that the most stable indicator of the characteristic void 'size' in the simulations is the mean fractional area covered by voids of diameter d, in a density field smoothed at its correlation length. Very accurate scaling behavior is found in power-law numerical models as they evolve. Eventually, this scaling breaks down as the nonlinearity reaches larger scales. It is shown that this breakdown is a manifestation of the undesirable effect of boundary conditions on simulations, even with the very large dynamic range possible here. A simple criterion is suggested for deciding when simulations with modest large-scale power may systematically underestimate the frequency of larger voids.

Kauffmann, Guinevere↗

NASA NTRS1972

Void growth in an elastic-plastic medium.

The uniaxial deformation of an elastic-plastic medium containing a doubly periodic square array of circular cylindrical voids is studied under plane-strain conditions. Both the effects of geometrical nonlinearities resulting from large deformation and physical nonlinearities arising from plastic material behavior are included in formulating the problem. A variational principle is used as the basis for implementing a finite-element solution. Results are obtained for the change in void shape and size under increasing overall strain, the overall tensile behavior of the material with voids, and the development of the plastic zone about a void.

Needleman, A.↗

NASA NTRS1985

Influence of voids on the strength of wrought materials

Three-dimensional voids, which are present in most materials, may be satisfactorily modelled by two-dimensional holes (i.e., cylindrical voids) in sheet metal. In this study, the influence of certain orientations and shapes of voids upon the mechanical properties and fracture behavior of certain ductile materials has been studied. The presence of voids is found to exert a negligible influence on the ultimate tensile strength, owing to plastic flow neutralizing the stress intensification present before yielding occurs. The shape and orientation of the defects, however, are seen to play an important role relative to strain at fracture. The maximum intensified tensile stress criterion which holds for brittle materials is found to apply to ductile materials as well.

Shaw, M. C.↗

NASA NTRS1987

Voids in Jovian magnetosphere revisited - Evidence of spacecraft charging

The Voyager 2 Plasma Science Instrument (PLS) measuring cold plasma number density observed about a dozen 'voids', lasting from a few minutes to 20 min, in the vicinity of the Ganymede-orbit crossing, when the low-energy ion and electron fluxes recorded fell to very low levels. Original interpretations associated these 'voids' with Ganymede wake effects. In the present study, the PLS data are reexamined, in conjunction with data from the magnetic field experiment and the low-energy charged particle (LECP) experiment. The LECP data showed that the PLS voids were accompanied by large enhancements of the flux of energetic electrons and ions, while the magnetic data exhibited no systematic signatures. It is suggested that increased energetic electron fluxes in the void regions intermittently charged the spacecraft negatively to values between a few kV and a few tens of kV, and that spacecraft charging could have produce dropouts in the measured cold ion and electron fluxes and enhancements in the measured fluxes of hot particles consistent with the observations.

Khurana, K. K.↗

NASA NTRS1988

Spectra of galaxies in the Case Low-Dispersion Sky Survey in the direction of the Bootes void

A sample of 34 galaxies selected from the Case Low-Dispersion Northern Sky Survey in the direction of the Bootes void. Emission-line redshifts were obtained for 33 objects; the spectrum of the thirty-fourth galaxy contains no obvious features. Three of the emission-line galaxies are lcoated within the boundaries of the Bootes void, including one not previously reported. To date, all the galaxies discovered in the void have emission-line spectra. Although more than half the galaxies in the sample are fainter than M(B) = -21.0 mag, all five of the galaxies that were detected by IRAS are brighter than M(B) = 21.5 mag. The relative strengths of the emission lines in most of the galaxies, including those in the void, indicate the lines are excited by photoionization due to young, hot O and B stars. Possible causes for the star formation occurring in these galaxies include interaction with nearby galaxies, star formation induced by nuclear activity, and/or recent development of physical conditions required for star formation.

Weistrop, Donna↗

NASA NTRS1989

Further spectroscopic studies of the Bootes region - Two more galaxies in the void

Redshifts are reported for 40 galaxies in the direction of the Bootes void identified in the Case Low-Dispersion Northern Sky Survey, List IV. Two new emission-line galaxies have been discovered in the void. The density of bright emission-line galaxies in the void is estimated to be a factor of 3 + or - 2 lower than the density of similar galaxies in the field. The galaxies are distributed uniformly with distance from the void center. A previously reported correlation between Case IV redshift estimates and measured redshifts is confirmed. Data for previously observed IRAS galaxies are combined with the present results to compared the luminosity distribution of IRAS galaxies to that for emission-line galaxies. The IRAS luminosity distribution contains a greater fraction of intrinsically bright galaxies than the emission-line galaxy distribution.

Weistrop, Donna↗

NASA NTRS1990

A deep redshift survey of IRAS galaxies towards the Bootes void

Redshifts were measured for a complete sample of galaxies detected by the IRAS within 11.5 deg of the center of the void in Bootes discovered by Kirshner et al (1981). There are 12 IRAS galaxies within the void as defined by the above authors, seven of which were discovered in this survey. One of these has a companion at the same redshift. The resulting density of IRAS galaxies in the void is measured to be between 1/6 and 1/3 of the average density; the uncertainty is dominated by Poisson statistics. Good agreement is found between the selection function and number density derived from the present sample and those derived from the all-sky sample of Strauss (1989). The optical spectra of the newly found galaxies in the void are typical of IRAS galaxies in the field.

Dey, Arjun↗