Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “turbulence optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Application of Aviation Turbulence Information to Air-Traffic Management (ATM): Chapter - 24

Unexpected turbulence especially in the upper troposphere and lower stratosphere where cabin crews and passengers in cruising aircraft are likely to unbuckle causes in-flight injuries, structural damage, and flight delay. Therefore, turbulence information can be used to improve safety while pursuing efficiency in Air-Traffic Management (ATM). In this chapter, simple modeling of aircraft trajectories combined with wind and turbulence predictions can suggest the optimal solution of flight plans that minimizes both total flight time (e.g., fuel consumption) and potential encounters of turbulence from departure to arrival airports. Also, probabilistic ensemble turbulence forecasts are applied to suggest an optimal strategic and tactical ATM route planning in a given weather and turbulence condition in the United States which are evaluated against in situ Eddy Dissipation Rate observations from commercial aircraft. Finally, variations of long-haul trans-Oceanic flight routes and their turbulence potentials are investigated using a global reanalysis data to understand how the upper-level large-scale flow patterns can affect the long-term ATM planning through the changes of winds and turbulence conditions.

Wind Optimal↗
NASA NTRS2001

Optimized suspension culture: the rotating-wall vessel

Suspension culture remains a popular modality, which manipulates mechanical culture conditions to maintain the specialized features of cultured cells. The rotating-wall vessel is a suspension culture vessel optimized to produce laminar flow and minimize the mechanical stresses on cell aggregates in culture. This review summarizes the engineering principles, which allow optimal suspension culture conditions to be established, and the boundary conditions, which limit this process. We suggest that to minimize mechanical damage and optimize differentiation of cultured cells, suspension culture should be performed in a solid-body rotation Couette-flow, zero-headspace culture vessel such as the rotating-wall vessel. This provides fluid dynamic operating principles characterized by 1) solid body rotation about a horizontal axis, characterized by colocalization of cells and aggregates of different sedimentation rates, optimally reduced fluid shear and turbulence, and three-dimensional spatial freedom; and 2) oxygenation by diffusion. Optimization of suspension culture is achieved by applying three tradeoffs. First, terminal velocity should be minimized by choosing microcarrier beads and culture media as close in density as possible. Next, rotation in the rotating-wall vessel induces both Coriolis and centrifugal forces, directly dependent on terminal velocity and minimized as terminal velocity is minimized. Last, mass transport of nutrients to a cell in suspension culture depends on both terminal velocity and diffusion of nutrients. In the transduction of mechanical culture conditions into cellular effects, several lines of evidence support a role for multiple molecular mechanisms. These include effects of shear stress, changes in cell cycle and cell death pathways, and upstream regulation of secondary messengers such as protein kinase C. The discipline of suspension culture needs a systematic analysis of the relationship between mechanical culture conditions and biological effects, emphasizing cellular processes important for the industrial production of biological pharmaceuticals and devices.

Non-NASA Center↗
NASA NTRS1980

A Navier-Stokes fast solver for turbulence modeling applications

A computer code for the evaluation and/or optimization of the predicative potential of second order turbulent closure models in simple two dimensional flow configurations is discussed. A procedure for the numerical solution of the steady constant property Navier-Stokes equations are described together with algebraic, one dimensional and two dimensional equations of turbulence closure models. Four turbulence models are compared with several sets of experimental data. The effects of initial conditions and boundary conditions are also described. The effects of purely numerical parameters, such as mesh size, boundary locations, and convergence criteria are presented.

Murphy, J. D.↗
NASA NTRS1972

A symmetrical laser Doppler velocity meter and its application to turbulence characterization

A symmetrical method of optical heterodyning of the Doppler shifted scattered laser radiation developed for velocity measurements with a minimal instrumental spectral broadening and a high signal-to-noise ratio. The method employs two laser beams incident on the moving scatterer and does not use any reference beam for heterodyning. The Doppler signal frequency is independent of the scattering angle and the signal possesses no receiving aperture broadening. Optical alignment is simple. Typical values of the instrumental spectral broadening were approximately 0.8 percent of the center frequency of the Doppler signal, and the signal-to-noise ratio was approximately 25 dB, obtained from an air flow system using submicron dioctylphthalate scattering aerosol. Experimental and theoretical studies were made on the characteristics of the Doppler signal and the effect of system parameters in turbulent flow measurement. The optimization process involved in the beam optics and in the use of a spatial filter is described. For localized flow measurement in any direction of the three-dimensional orthogonal coordinates, the system, using uncorrected optical components, had a sensing volume which can be described by a sensitive length of 600 microns and a diameter of 100 microns.

Mazumder, M. K.↗
NASA NTRS1992

Development of an algebraic turbulence model for analysis of propulsion flows

A simple turbulence model that will be applicable to propulsion flows having both wall bounded and unbounded regions was developed and installed within the PARC Navier-Stokes code by linking two existing algebraic turbulence models. The first is the Modified Mixing Length (MML) model which is optimized for wall bounded flows. The second is the Thomas model, the standard algebraic turbulence model in PARC which has been used to calculate both bounded and unbounded turbulent flows but was optimized for the latter. This paper discusses both models and the method employed to link them into one model (referred to as the MMLT model). The PARC code with the MMLT model was applied to two dimensional turbulent flows over a flat plate and over a backward facing step to validate and optimize the model and to compare its predictions to those obtained with the three turbulence models already available in PARC.

Georgiadis, N. J.↗
NASA NTRS1992

Development of an algebraic turbulence model for analysis of propulsion flows

A simple turbulence model that will be applicable to propulsion flows having both wall bounded and unbounded regions was developed and installed within the PARC Navier-Stokes code by linking two existing algebraic turbulence models. The first is the Modified Mixing Length (MML) model which is optimized for wall bounded flows. The second is the Thomas model, the standard algebraic turbulence model in PARC which has been used to calculate both bounded and unbounded turbulent flows but was optimized for the latter. This paper discusses both models and the method employed to link them into one model (referred to as the MMLT model). The PARC code with the MMLT model was applied to two dimensional turbulent flows over a flat plate and over a backward facing step to validate and optimize the model and to compare its predictions to those obtained with the three turbulence models already available in PARC.

Georgiadis, N. J.↗
NASA NTRS1993

Some practical turbulence modeling options for Reynolds-averaged full Navier-Stokes calculations of three-dimensional flows

New turbulence modeling options recently implemented for the 3D version of Proteus, a Reynolds-averaged compressible Navier-Stokes code, are described. The implemented turbulence models include: the Baldwin-Lomax algebraic model, the Baldwin-Barth one-equation model, the Chien k-epsilon model, and the Launder-Sharma k-epsilon model. Features of this turbulence modeling package include: well documented and easy to use turbulence modeling options, uniform integration of turbulence models from different classes, automatic initialization of turbulence variables for calculations using one- or two-equation turbulence models, multiple solid boundaries treatment, and fully vectorized L-U solver for one- and two-equation models. Good agreements are obtained between the computational results and experimental data. Sensitivity of the compressible turbulent solutions with the method of y(+) computation, the turbulent length scale correction, and some compressibility corrections are examined in detail. Test cases show that the highly optimized one- and two-equation turbulence models can be used in routine 3D Navier-Stokes computations with no significant increase in CPU time as compared with the Baldwin-Lomax algebraic model.

Bui, Trong T.↗
NASA NTRS2001

Computational Analyses of Propulsion Aeroacoustics for Mixed Flow Nozzle Pylon Installation at Takeoff

A CFD analyses is presented for a set of baseline and noise suppression mixed flow nozzles with and without a pylon installation. The five model configurations are as follows; a baselinecore/fan dual-stream nozzle with an external plug, a chevron mixer nozzle with a peak on the symmetry plane with external plug, both of the above nozzles with an installed bifurcatingpylon and lastly a clocked chevron mixer nozzle such that a trough is aligned with the center of the pylon. The fluid flow is simulated by solving the asymptotically steady, compressible, Reynolds-averaged Navier-Stokes equations using an implicit, up-wind, flux-difference splitting finite volume scheme and standard two equation k-epsilon turbulence model with a linear stress representation. All computations are performed using the multiblock, parallel, structuredcode PAB3D. Results indicate that the clocked chevron with pylon case achieves the most optimal levels of average and peak turbulence kinetic energy and vorticity and therefore is expected to be the quietest of the five configurations tested. Further study is required to refine expressions which are indicative of noise and mate these with rigorous noise prediction models.

Massey, Steven J.↗
NASA NTRS1993

Feedback control for unsteady flow and its application to the stochastic Burgers equation

The study applies mathematical methods of control theory to the problem of control of fluid flow with the long-range objective of developing effective methods for the control of turbulent flows. Model problems are employed through the formalism and language of control theory to present the procedure of how to cast the problem of controlling turbulence into a problem in optimal control theory. Methods of calculus of variations through the adjoint state and gradient algorithms are used to present a suboptimal control and feedback procedure for stationary and time-dependent problems. Two types of controls are investigated: distributed and boundary controls. Several cases of both controls are numerically simulated to investigate the performances of the control algorithm. Most cases considered show significant reductions of the costs to be minimized. The dependence of the control algorithm on the time-descretization method is discussed.

Choi, Haecheon↗
NASA NTRS1993

Some practical turbulence modeling options for Reynolds-averaged full Navier-Stokes calculations of three-dimensional flows

New turbulence modeling options recently implemented for the 3-D version of Proteus, a Reynolds-averaged compressible Navier-Stokes code, are described. The implemented turbulence models include: the Baldwin-Lomax algebraic model, the Baldwin-Barth one-equation model, the Chien k-epsilon model, and the Launder-Sharma k-epsilon model. Features of this turbulence modeling package include: well documented and easy to use turbulence modeling options, uniform integration of turbulence models from different classes, automatic initialization of turbulence variables for calculations using one- or two-equation turbulence models, multiple solid boundaries treatment, and fully vectorized L-U solver for one- and two-equation models. Validation test cases include the incompressible and compressible flat plate turbulent boundary layers, turbulent developing S-duct flow, and glancing shock wave/turbulent boundary layer interaction. Good agreement is obtained between the computational results and experimental data. Sensitivity of the compressible turbulent solutions with the method of y(sup +) computation, the turbulent length scale correction, and some compressibility corrections are examined in detail. The test cases show that the highly optimized one-and two-equation turbulence models can be used in routine 3-D Navier-Stokes computations with no significant increase in CPU time as compared with the Baldwin-Lomax algebraic model.

Bui, Trong T.↗
NASA NTRS2019

Scale-Resolving Simulations of Laminar-to-Turbulent Transition in Swept-Wing Flow

Aerodynamic shape optimization of swept Natural Laminar Flow (NLF) wing design plays an important role for the development of future energy-efficient commercial transport aircraft. Lack of predictive laminar-to-turbulent transition modeling capabilities is still limiting the extent to which design can rely on computational tools, while making costly wind tunnel and flight tests a necessity. Prediction of transition on practical 3D wing geometries using the e (sup N) method coupled with laminar boundary layer and linear stability codes or local statistical correlation CFD (Computational Fluid Dynamics) models such as the gamma - Re (sub theta) Langtry-Menter model have proven challenging, whereas transitional hybrid RANS-LES solvers have shown encouraging but still mitigated results.

Scale-resolving↗
NASA NTRS2000

Studying Turbulence Using Numerical Simulation Databases, 8. Proceedings of the 2000 Summer Program

The eighth Summer Program of the Center for Turbulence Research took place in the four-week period, July 2 to July 27, 2000. This was the largest CTR Summer Program to date, involving forty participants from the U. S. and nine other countries. Twenty-five Stanford and NASA-Ames staff members facilitated and contributed to most of the Summer projects. Several new topical groups were formed, which reflects a broadening of CTR's interests from conventional studies of turbulence to the use of turbulence analysis tools in applications such as optimization, nanofluidics, biology, astrophysical and geophysical flows. CTR's main role continues to be in providing a forum for the study of turbulence and other multi-scale phenomena for engineering analysis. The impact of the summer program in facilitating intellectual exchange among leading researchers in turbulence and closely related flow physics fields is clearly reflected in the proceedings.

Source record↗
NASA NTRS2020

Shape Optimization of Vortex Generators to Control Mack Mode Amplification

This paper demonstrates the potential to use shape optimization for the design of vortex generators in an axisymmetric boundary layer. This shape optimization increases the amplitude of stationary streaks created by streamwise vorticity, with the goal of reducing the amplification of Mack mode instabilities. The test case under consideration matches a trajectory point during the ascent phase of the HIFiRE-1 flight experiment. Wall-mounted vortex generators are added to the cone and their shape is optimized to control the amplification of Mack mode instabilities that are known to initiate laminar-turbulent transition in this flow. An empirical objective function is developed based on the previous studies of optimal streaks. A constraint on the maximum streak amplitude is added to avoid the initiation of bypass transition. The shape optimization is conducted using SU2, an open-source suite for multiphysics simulation and design. A significant improvement is observed in an integral metric of the streak amplitude, while the maximum streak amplitude is maintained close to the baseline level. The qualitative features of the optimized geometry are discussed.

Vortex generators↗
NASA NTRS2019

A New Recycling Method to Generate Turbulent Inflow Profiles

The accuracy of the scale-resolving simulations for practical geometries strongly depends on the inflow boundary conditions. Imposing experimentally observed turbulent inflow profiles for the numerical simulations is a major challenge. Existing methods available in the literature assume self-similar behavior, which is not true for most of the experiments. In the present work, we formulate the turbulent inflow profile generation technique as an optimization problem. An adjoint technique is exploited to evaluate the sensitivities of multiple input parameters for the present problem. The present formulation is then tested to generate a laminar boundary layer profile, turbulent boundary layer profile, and turbulent jet profile.

Garai, Anirban↗
NASA NTRS1972

Low-speed aerodynamic characteristics of an airfoil optimized for maximum lift coefficient

An investigation has been conducted in the Langley low-turbulence pressure tunnel to determine the two-dimensional characteristics of an airfoil optimized for maximum lift coefficient. The design maximum lift coefficient was 2.1 at a Reynolds number of 9.7 million. The airfoil with a smooth surface and with surface roughness was tested at angles of attack from 6 deg to 26 deg, Reynolds numbers (based on airfoil chord) from 2.0 million to 12.9 million, and Mach numbers from 0.10 to 0.35. The experimental results are compared with values predicted by theory. The experimental pressure distributions observed at angles of attack up to at least 12 deg were similar to the theoretical values except for a slight increase in the experimental upper-surface pressure coefficients forward of 26 percent chord and a more severe gradient just behind the minimum-pressure-coefficient location. The maximum lift coefficients were measured with the model surface smooth and, depending on test conditions, varied from 1.5 to 1.6 whereas the design value was 2.1.

Bingham, G. J.↗