Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “trucks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

An investigation of drag reduction for a standard truck with various modifications

A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a standard truck model. The physical variables included: a cab mounted air deflector; a boattail on the rear of the cargo compartment; flow-vanes on the front of the cargo compartment; and a forebody fairing over the cab. Tests were conducted at yaw angles (relative wind angle) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.4 x 100,000 to 6.1 x 100,000 based upon the equivalent diameter of the vehicles. The forebody fairing and the flow-vane with the closed bottom were very effective in improving the flow over the forward part of the cargo compartment. The forebody fairing provided a calculated fuel saving of 5.6 liters per hour (1.5 gallons per hour) over the baseline configuration for a ground speed of 88.6 km/hr (55 mph) in national average winds.

Muirhead, V. U.↗
NASA NTRS1982

Vehicle test report: Battronic pickup truck

An electric pickup truck was tested to characterize certain parameters and to provide baseline data that can be used for the comparison of improved batteries that may be incorporated into the vehicle at a later time. The vehicle tests were concentrated on the electrical drive subsystem; i.e., the batteries, controller, and motor. The tests included coastdowns to characterize the road load and range evaluations for both cyclic and constant speed conditions. A qualitative evaluation of the vehicle's performance was made by comparing its constant speed range performance with other vehicles.

Price, T. W.↗
NASA NTRS1984

Parametric analysis of synthetic aperture radar data acquired over truck garden vegetation

An airborne X-band SAR acquired multipolarization and multiflight pass SAR images over a truck garden vegetation area. Based on a variety of land cover and row crop direction variations, the vertical (VV) polarization data contain the highest contrast, while cross polarization contains the least. When the radar flight path is parallel to the row direction, both horizontal (HH) and VV polarization data contain very high return which masks out the specific land cover that forms the row structure. Cross polarization data are not that sensitive to row orientation. The inclusion of like and cross polarization data help delineate special surface features (e.g., row crop against non-row-oriented land cover, very-rough-surface against highly row-oriented surface).

Wu, S. T.↗
NASA NTRS2002

Implications of Automotive and Trucking On-Board Information Systems for General Aviation Cockpit Weather Systems

In this study, current characteristics and future developments of Intelligent Transportation Systems (ITS) in the automobile and trucking industry are investigated to identify the possible implications of such systems for General Aviation (GA) cockpit weather systems. First, ITS are explained based on tracing their historical development in various countries. Then, current systems and the enabling communication technologies are discussed. Finally, a market analysis for GA is included.

Sireli, Yesim↗
NASA NTRS2002

So Much Depends Upon a Pickup Truck

An anecdote from the author's own career as a researcher stresses the importance of becoming thoroughly familiar with a subject under study, in order to avoid overlooking obvious factors. In one study he conducted in Israel, he found that pickup truck size sometimes determined work crew size.

Laufer, Alexander↗
NASA NTRS1984

Weight Control for Highway Trucking

LODEC, Inc. scales use load cell technology, a spinoff from aerospace technology, in manufacturing electronic axle scales for weighing trucks and trailers to insure that they are within legal highway limits. The scales trace their origin to the space program of the 1960's when ELDEC Corporation, then LODEC parent company, acquired advanced electronic technology as a subcontractor on such projects as Apollo and Saturn launch vehicles. LODEC scales come in both permanent and portable versions with accuracy of within one percent and frequently better.

Source record↗
NASA NTRS2020

Air Quality Monitoring Case Study Using Mobile Low-cost Sensors Mounted on Trash-Trucks: Methods Development and Lessons Learned

Air quality monitoring (AQM) is crucial for cities to develop management plans supporting population health. However, there is a dearth of measurements due to the high cost of standard reference instruments. Mobile AQM using low-cost sensors deployed on routine fleets of vehicles can enable the continuous detection of fine-scale pollutant variations in cities at a lower cost. New methods need to be developed to interpret these measurements. This paper presents three such methods. First, we propose a technique to identify aerosol hotspots. Second, we employ techniques published previously to assess the generalizable map of fine and coarse particle number concentrations, to understand qualitatively the contribution of local and regional sources across the region sampled. By using the raw number concentration of differently sized particles from the Optical Particle Counters (OPCs) instead of the noisier mass concentrations, we obtain more robust results. Third, in order to evaluate source signatures in cities, we propose another technique, in which we cluster the entire range of aerosol size-distribution measurements acquired. The properties of each cluster provide insight into the aerosol source characteristics in the sampling environment. We test these methods using a dataset we collected by mounting OPCs on two trash-trucks in Cambridge, Massachusetts.

Drive-by sensing↗
NASA NTRS2020

Air Quality Monitoring Case Study Using Mobile Low-cost Sensors mounted on Trash-Trucks: Methods Development and Lessons Learned

Air quality monitoring (AQM) is crucial for cities to develop management plans supporting population health. However, there is a dearth of measurements due to the high cost of standard reference instruments. Mobile AQM using low-cost sensors deployed on routine fleets of vehicles can enable the continuous detection of fine-scale pollutant variations in cities at a lower cost. New methods need to be developed to interpret these measurements. This paper presents three such methods. First, we propose a technique to identify aerosol hotspots. Second, we employ techniques published previously to assess the generalizable map of fine and coarse particle number concentrations, to understand qualitatively the contribution of local and regional sources across the region sampled. By using the raw number concentration of differently sized particles from the Optical Particle Counters (OPCs) instead of the noisier mass concentrations, we obtain more robust results. Third, in order to evaluate source signatures in cities, we propose another technique, in which we cluster the entire range of aerosol size-distribution measurements acquired. The properties of each cluster provide insight into the aerosol source characteristics in the sampling environment. We test these methods using a dataset we collected by mounting OPCs on two trash-trucks in Cambridge, Massachusetts.

Drive-by sensing↗
NASA NTRS1970

Tandem wheel drop-legs for standard truck trailer

Tandem wheel drop-leg device provides a semitrailer with fore and aft mobility that allows it to be moved without a prime mover. The modified drop-legs have trunnion dual wheels and an adjustable brace.

Cantwell, W.↗
NASA NTRS1977

Reduced truck fuel consumption through aerodynamic design

Full-scale fuel consumption and drag tests were performed on a conventional cab-over-engine tractor-trailer combination and a version of the same vehicle with significant forebody modifications. The modified configuration had greatly increased radii on all front corners and edges of the tractor and a smooth fairing of the modified tractor top and sides extending to the trailer. Concurrent highway testing of the two configurations showed that the modified design used 20% to 24% less fuel than the baseline configuration at 88.5 km/hr (55 mph) with near-calm wind conditions. Coastdown test results showed that the modified configuration reduced the drag coefficient by 0.43 from the baseline value of 1.17 at 88.5 km/hr (55 mph) in calm wind conditions.

Steers, L. L.↗
NASA NTRS1978

Utilization of waste heat in trucks for increased fuel economy

The waste heat utilization concepts include preheating, regeneration, turbocharging, turbocompounding, and Rankine engine compounding. Predictions are based on fuel-air cycle analyses, computer simulation, and engine test data. All options are evaluated in terms of maximum theoretical improvements, but the Diesel and adiabatic Diesel are also compared on the basis of maximum expected improvement and expected improvement over a driving cycle. The study indicates that Diesels should be turbocharged and aftercooled to the maximum possible level. The results reveal that Diesel driving cycle performance can be increased by 20% through increased turbocharging, turbocompounding, and Rankine engine compounding. The Rankine engine compounding provides about three times as much improvement as turbocompounding but also costs about three times as much. Performance for either can be approximately doubled if applied to an adiabatic Diesel.

Leising, C. J.↗
NASA NTRS1983

An investigation of the internal and external aerodynamics of cattle trucks

Wind tunnel tests were conducted on a one-tenth scale model of a conventional tractor trailer livestock hauler to determine the air flow through the trailer and the drag of the vehicle. These tests were conducted with the trailer empty and with a full load of simulated cattle. Additionally, the drag was determined for six configurations, of which details for three are documented herein. These are: (1) conventional livestock trailer empty, (2) conventional trailer with smooth sides (i.e., without ventilation openings), and (3) a stream line tractor with modified livestock trailer (cab streamlining and gap fairing). The internal flow of the streamlined modification with simulated cattle was determined with two different ducting systems: a ram air inlet over the cab and NACA submerged inlets between the cab and trailer. The air flow within the conventional trailer was random and variable. The streamline vehicle with ram air inlet provided a nearly uniform air flow which could be controlled. The streamline vehicle with NACA submerged inlets provided better flow conditions than the conventional livestock trailer but not as uniform or controllable as the ram inlet configuration.

Muirhead, V. U.↗
NASA NTRS1985

Future heavy duty trucking engine requirements

Developers of advanced heavy duty diesel engines are engaged in probing the opportunities presented by new materials and techniques. This process is technology driven, but there is neither assurance that the eventual users of the engines so developed will be comfortable with them nor, indeed, that those consumers will continue to exist in either the same form, or numbers as they do today. To ensure maximum payoff of research dollars, the equipment development process must consider user needs. This study defines motor carrier concerns, cost tolerances, and the engine parameters which match the future projected industry needs. The approach taken to do that is to be explained and the results presented. The material to be given comes basically from a survey of motor carrier fleets. It provides indications of the role of heavy duty vehicles in the 1998 period and their desired maintenance and engine performance parameters.

Strawhorn, L. W.↗
NASA NTRS1987

Technical and economic study of Stirling and Rankine cycle bottoming systems for heavy truck diesel engines

Bottoming cycle concepts for heavy duty transport engine applications were studied. In particular, the following tasks were performed: (1) conceptual design and cost data development for Stirling systems; (2) life-cycle cost evaluation of three bottoming systems - organic Rankine, steam Rankine, and Stirling cycles; and (3) assessment of future directions in waste heat utilization research. Variables considered for the second task were initial capital investments, fuel savings, depreciation tax benefits, salvage values, and service/maintenance costs. The study shows that none of the three bottoming systems studied are even marginally attractive. Manufacturing costs have to be reduced by at least 65%. As a new approach, an integrated Rankine/Diesel system was proposed. It utilizes one of the diesel cylinders as an expander and capitalizes on the in-cylinder heat energy. The concept eliminates the need for the power transmission device and a sophisticated control system, and reduces the size of the exhaust evaporator. Results of an economic evaluation indicate that the system has the potential to become an attractive package for end users.

Kubo, I.↗
NASA NTRS2011

Fairing Well: Aerodynamic Truck Research at NASA Dryden Flight Research Center

In 1973 engineers at Dryden began investigating ways to reduce aerodynamic drag on land vehicles. They began with a delivery van whose shape they changed dramatically, finally reducing its aerodynamic drag by more than 5 percent. They then turned their attention to tracator-trailers, modifying a cab-over and reducing its aerodynamic drag by nearly 25 percent. Further research identified additional areas worth attention, but in the intervening decades few of those changes have appeared.

Gelzer, Christian↗
NASA NTRS2005

Space Shuttle Crawler Transporter Truck Shoe Qualification Tests and Analyses for Return-to-Flight

A vital element to Launch Complex 39 (LC39) and NASA's Kennedy Space Center (KSC) mobile launch transfer operation is a 3 million kilogram behemoth known as the Crawler Transporter (CT). Built in the 1960's, two CT's have accumulated over 1700+ miles each and have been used for the Apollo and the Space Shuttle programs. Recent observation of fatigue cracks on the CT shoes led to a comprehensive engineering, structural and metallurgical evaluation to assess the root cause that necessitated procurement of over 1000 new shoes. This paper documents the completed dynamic and compression tests on the old and new shoes respectively, so as to certify them for Space Shuttle's return-to-flight (RTF). Measured strain data from the rollout tests was used to develop stress/loading spectra and static equivalent load for qualification testing of the new shoes. Additionally, finite element analysis (FEA) was used to conduct sensitivity analyses of various contact parameters and structural characteristics for acceptance of new shoes.

Margasahayam, Ravi N.↗