Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transient expression system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Mixing and transient interface condensation of a liquid hydrogen tank

Experiments were conducted to investigate the effect of axial jet-induced mixing on the pressure reduction of a thermally stratified liquid hydrogen tank. The tank was nearly cylindrical, having a volume of about 0.144 cu m with 0.559 m in diameter and 0.711 m long. A mixer/pump unit, which had a jet nozzle outlet of 0.0221 m in diameter was located 0.178 m from the tank bottom and was installed inside the tank to generate the axial jet mixing and tank fluid circulation. The liquid fill and jet flow rate ranged from 42 to 85 percent (by volume) and 0.409 to 2.43 cu m/hr, respectively. Mixing tests began with the tank pressure ranging from 187.5 to 238.5 kPa at which the thermal stratification results in 4.9 to 6.2 K liquid sub cooling. The mixing time and transient vapor condensation rate at the liquid-vapor interface are determined. Two mixing time correlations, based on the thermal equilibrium and pressure equilibrium, are developed. Both mixing time correlations are expressed as functions of system and buoyancy parameters and compared well with other experimental data. The steady state condensation rate correlation of Sonin et al. based on steam-water data is modified and expressed as a function of jet subcooling. The limited liquid hydrogen data of the present study shows that the modified steady state condensation rate correlation may be used to predict the transient condensation rate in a mixing process if the instantaneous values of jet sub cooling and turbulence intensity at the interface are employed.

Lin, C. S.↗

An approximation technique for predicting the transient response of a second order nonlinear equation

An approximation technique has been developed for determining the transient response of a nonlinear dynamic system. The nonlinearities in the system which has been considered appear in the system's dissipation function. This function was expressed as a second order polynomial in the system's velocity. The developed approximation is an extension of the classic Kryloff-Bogoliuboff technique. Two examples of the developed approximation are presented for comparative purposes with other approximation methods.

Laurenson, R. M.↗

Noise-Resilient Quantum Machine Learning for Stability Assessment of Power Systems

Transient stability assessment (TSA) is a cornerstone for resilient operations of todays interconnected power grids. This paper is a confluence of quantum computing, data science and machine learning to potentially address the power system TSA issue. Here, we devise a quantum TSA (QTSA) method to enable scalable and efficient data-driven transient stability prediction for bulk power systems, which is the first attempt to tackle the TSA issue with quantum computing. Our contributions are three-fold: 1) A high expressibility, low-depth (HELD) quantum circuit is designed for accurate and noise-resilient TSA; 2) A quantum natural gradient descent algorithm is developed for efficient HELD circuit training; 3) A systematical analysis on QTSAs performance under various quantum factors is per-formed. QTSA underpins a foundation of quantum-enabled and data-driven power grid stability analytics. It renders the intractable TSA straightforward and effortless in the Hilbert space, and therefore provides stability information for power system operations. Extensive experiments on quantum simulators and real quantum computers verify the accuracy, noise-resilience, scalability and universality of QTSA.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Analytical model for laser-induced transient grating measurements of thermal diffusivity in non-opaque materials

The thermal transport and elastic properties of materials are often measured using the laser-induced transient grating spectroscopy (TGS) technique. The analysis of the TGS signal usually involves fitting well-known expressions, derived assuming the limiting cases of opaque or transparent materials, to the measured data. In this paper, the system of thermoelastic equations is analytically solved for an isotropic homogeneous material assuming finite laser penetration depth, which is an important consideration when the penetration depth is on the order of the acoustic wavelength. The need to use such a solution is discussed and compared to the expression for opaque material. The solution is benchmarked against TGS signal measured on single-crystal silicon with {100} surface orientation and is found to significantly improve the accuracy of the calculated thermal diffusivity as compared to using the expression for opaque material.

36 MATERIALS SCIENCE↗

Geometry-Dependent Solidification Regimes in Metal Additive Manufacturing

Recent modeling and experimental work in additive manufacturing has suggested that cross-sectional geometry may play a significant role in the local development of the solidification structure through its influence on the heat source path. This effect has been rationalized as the transition from a quasi-static point heat source regime, to a regime dominated by the quasi-static motion of an equivalent line source. This work provides a simple analytical framework for determining the conditions under which a system transitions between these regimes. Here, a transient semi-analytical heat transfer model is used to examine a wide range of process conditions and material properties. A simple analytical expression is derived and shown to accurately predict the transition between solidification regimes over these conditions. The functional form of this expression is then used to help understand the importance of various material properties, process parameters, and geometric factors on the characteristics of the solidification conditions. This approach may be used as a simple guideline for optimizing process conditions in response to variations in cross-sectional geometry to produce more consistent microstructural distributions in additively manufactured components.

36 MATERIALS SCIENCE↗

Insights of Molecular Mechanism of Xylem Development in Five Black Poplar Cultivars

Black poplar (Populus deltoides, P. nigra, and their hybrids) is the main poplar cultivars in China. It offers interesting options of large-scale biomass production for bioenergy due to its rapid growth and high yield. Poplar wood properties were associated with chemical components and physical structures during wood formation. In this study, five poplar cultivars, P. euramericana ‘Zhonglin46’ (Pe1), P. euramericana ‘Guariento’ (Pe2), P. nigra ‘N179’ (Pn1), P. deltoides ‘Danhong’ (Pd1), and P. deltoides ‘Nanyang’ (Pd2), were used to explore the molecular mechanism of xylem development. We analyzed the structural differences of developing xylem in the five cultivars and profiled the transcriptome-wide gene expression patterns through RNA sequencing. The cross sections of the developing xylem showed that the cell wall thickness of developed fiber in Pd1 was thickest and the number of xylem vessels of Pn1 was the least. A total of 10,331 differentially expressed genes were identified among 10 pairwise comparisons of the five cultivars, most of them were related to programmed cell death and secondary cell wall thickening. K-means cluster analysis and Gene Ontology enrichment analysis showed that the genes highly expressed in Pd1 were related to nucleotide decomposition, metabolic process, transferase, and microtubule cytoskeleton; whereas the genes highly expressed in Pn1 were involved in cell wall macromolecule decomposition and polysaccharide binding processes. Based on a weighted gene co-expression network analysis, a large number of candidate regulators for xylem development were identified. And their potential regulatory roles to cell wall biosynthesis genes were validated by a transient overexpression system. This study provides a set of promising candidate regulators for genetic engineering to improve feedstock and enhance biofuel conversion in the bioenergy crop Populus.

59 BASIC BIOLOGICAL SCIENCES↗

eYGFPuv-Assisted Transgenic Selection in Populus deltoides WV94 and Multiplex Genome Editing in Protoplasts of P. trichocarpa × P. deltoides Clone ‘52-225’

Although CRISPR/Cas-based genome editing has been widely used for plant genetic engineering, its application in the genetic improvement of trees has been limited, partly because of challenges in Agrobacterium-mediated transformation. As an important model for poplar genomics and biotechnology research, eastern cottonwood (Populus deltoides) clone WV94 can be transformed by A. tumefaciens, but several challenges remain unresolved, including the relatively low transformation efficiency and the relatively high rate of false positives from antibiotic-based selection of transgenic events. Moreover, the efficacy of CRISPR-Cas system has not been explored in P. deltoides yet. Here, we first optimized the protocol for Agrobacterium-mediated stable transformation in P. deltoides WV94 and applied a UV-visible reporter called eYGFPuv in transformation. Our results showed that the transgenic events in the early stage of transformation could be easily recognized and counted in a non-invasive manner to narrow down the number of regenerated shoots for further molecular characterization (at the DNA or mRNA level) using PCR. We found that approximately 8.7% of explants regenerated transgenic shoots with green fluorescence within two months. Next, we examined the efficacy of multiplex CRISPR-based genome editing in the protoplasts derived from P. deltoides WV94 and hybrid poplar clone ‘52-225’ (P. trichocarpa × P. deltoides clone ‘52-225’). The two constructs expressing the Trex2-Cas9 system resulted in mutation efficiency ranging from 31% to 57% in hybrid poplar clone 52-225, but no editing events were observed in P. deltoides WV94 transient assay. The eYGFPuv-assisted plant transformation and genome editing approach demonstrated in this study has great potential for accelerating the genome editing-based breeding process in poplar and other non-model plants species and point to the need for additional CRISPR work in P. deltoides.

59 BASIC BIOLOGICAL SCIENCES↗

Mixing Cell Model: A One-Dimensional Numerical Model for Assessment of Water Flow and Contaminant Transport in the Unsaturated Zone

This report describes the Mixing Cell Model code, a one dimensional model for water flow and solute transport in the unsaturated zone under steady state or transient flow conditions. The model is based on the principles and assumptions underlying mixing-cell model formulations. The unsaturated zone is discretized into a series of independent mixing cells. Each cell may have unique hydrologic, lithologic, and sorptive properties. Ordinary differential equations describe the material (water and solute) balance within each cell. Water-flow equations are derived from the continuity equation, assuming that unit gradient conditions exist at all times in each cell. Pressure gradients are considered implicitly through model discretization. Unsaturated hydraulic conductivity and moisture contents are determined by the material specific moisture-characteristic curves. Solute-transport processes include explicit treatment of advective processes, first order chain decay, and linear sorption reactions. Dispersion is addressed through implicit and explicit dispersion. Implicit dispersion is an inherent feature of all mixing-cell models and originates from the formulation of the problem in terms of mass balance around fully mixed volume elements. Expressions are provided that relate implicit dispersion to the physical dispersion of the system. Two FORTRAN codes were developed to solve the water flow and solute-transport equations: (1) the Mixing Cell Model for Flow (MCMF) solves transient water-flow problems and (2) the Mixing Cell Model for Transport (MCMT) solves the solute-transport problem. The transient water-flow problem is typically solved first by estimating the water flux through each cell in the model domain as a function of time using the MCMF code. These data are stored in either ASCII or binary files that are later read by the solute transport code (MCMT). Code output includes solute pore water concentrations, water and solute inventories in each cell and at each specified output time, and water and solute fluxes through each cell and specified output time. Computer run times for coupled transient water flow and solute transport were typically several seconds on a 2 GHz Intel Pentium IV desktop computer. The model was benchmarked against analytical solutions and finite element approximations to the partial differential equations (PDE) describing unsaturated flow and transport. Differences between the maximum solute flux estimated by the mixing cell model and the PDE models were typically less than two percent. This revision includes an option for a fixed concentration lower boundary condition for diffusive fluxes for versions 020321 and later.

54 ENVIRONMENTAL SCIENCES↗

Thermal shock resistance of ceramic matrix composites

The experimental and analytical investigation of the thermal shock phenomena in ceramic matrix composites is detailed. The composite systems examined were oxide-based, consisting of an aluminosilicate matrix with either polycrystalline aluminosilicate or single crystal alumina fiber reinforcement. The program was divided into three technical tasks; baseline mechanical properties, thermal shock modeling, and thermal shock testing. The analytical investigation focused on the development of simple expressions for transient thermal stresses induced during thermal shock. The effect of various material parameters, including thermal conductivity, elastic modulus, and thermal expansion, were examined analytically for their effect on thermal shock performance. Using a simple maximum stress criteria for each constituent, it was observed that fiber fracture would occur only at the most extreme thermal shock conditions and that matrix fracture, splitting parallel to the reinforcing fiber, was to be expected for most practical cases. Thermal shock resistance for the two material systems was determined experimentally by subjecting plates to sudden changes in temperature on one surface while maintaining the opposite surface at a constant temperature. This temperature change was varied in severity (magnitude) and in number of shocks applied to a given sample. The results showed that for the most severe conditions examined that only surface matrix fracture was present with no observable fiber fracture. The impact of this damage on material performance was limited to the matrix dominated properties only. Specifically, compression strength was observed to decrease by as much as 50 percent from the measured baseline.

Carper, D. M.↗

A simplified method for approximating the transient motion in angles of attack and sideslip during a constant rolling maneuver

The transient motion in angles of attack and sideslip during a constant rolling maneuver has been analyzed. Simplified expressions are presented for the determination of the pertinent modes of motion as well as the modal coefficient corresponding to each mode. Calculations made with and without the derivatives for side force due to sideslip and lift-curve slope indicate that although these derivatives increase the total damping of the system they do not markedly affect the transient motion.

Sternfield, Leonard↗

Substructuring techniques

The substructure function generator program is discussed. Input to this program consists of a definition of a finite element model of a substructure, and specification of the type and number of displacement functions to be generated. Primary output is a substructure data file containing the substructure mass and stiffness matrices expressing kinetic and potential energies as quadratic forms in coefficients of the displacement functions, etc. The substructure synthesis program forms complete system mass, stiffness, and damping matrices, computes system modes and frequencies, and executes transient response calculations. Input to this program consists of the array of substructure data files generated by the function generator program for individual substructures, and data cards defining the position and interconnection of the substructures, damping data, forcing function details, and function control parameters.

Whetstone, W. D.↗

Capillary Flow in Containers of Polygonal Section: Theory and Experiment

An improved understanding of the large-length-scale capillary flows arising in a low-gravity environment is critical to that engineering community concerned with the design and analysis of spacecraft fluids management systems. Because a significant portion of liquid behavior in spacecraft is capillary dominated it is natural to consider designs that best exploit the spontaneous character of such flows. In the present work, a recently verified asymptotic analysis is extended to approximate spontaneous capillary flows in a large class of cylindrical containers of irregular polygonal section experiencing a step reduction in gravitational acceleration. Drop tower tests are conducted using partially-filled irregular triangular containers for comparison with the theoretical predictions. The degree to which the experimental data agree with the theory is a testament to the robustness of the basic analytical assumption of predominantly parallel flow. As a result, the closed form analytical expressions presented serve as simple, accurate tools for predicting bulk flow characteristics essential to practical low-g system design and analysis. Equations for predicting corner wetting rates, total container flow rates, and transient surfaces shapes are provided that are relevant also to terrestrial applications such as capillary flow in porous media.

Weislogel, Mark M.↗

Improved Biofuel Production through Discovery and Engineering of Terpene Metabolism in Switchgrass

Project Objectives - Of the myriad specialized metabolites that plants deploy to adapt to environmental challenges, terpenes form the largest group. In many major crops, unique terpene blends serve as key stress defenses that directly impact plant fitness and yield. In addition, terpenes, such as bisabolene and pinene, are used for producing renewable biofuels. Essential to advancing a broader use of terpenes for biofuel feedstock engineering is a system-wide knowledge of the diverse biosynthetic machinery and defensive potential of often species-specific terpene blends. The proposed project would merge genome-wide enzyme discovery with comparative –omics, protein structural and plant microbiome studies to define the biosynthesis and stress-defensive functions of the switchgrass (Panicum virgatum) terpene network. These insights would be combined with developing and applying non-transgenic genome editing tools to design plants with desirable terpene blends for higher productivity and biofuel production on marginal lands. As a dedicated lignocellulosic feedstock for U.S. biofuel production with high net energy yield, stress tolerance, and available genome resources, switchgrass is well-suited for devising new avenues for biofuel production. Project Description – The diversity of plant terpene defenses is governed by species-specific families of terpene synthase (TPS) and cytochrome P450 monooxygenase (P450) enzymes. Mining of the switchgrass genome (genotype Alamo) identified ~100 TPS and P450 candidate genes, and combinatorial biochemical analysis of synthesized TPSs and P450s revealed more than a dozen enzymes with common and novel activities. In addition, several identified terpene metabolites and the corresponding transcripts were up-regulated in response to abiotic stressors. These findings demonstrate a unique switchgrass terpene network with probable importance to abiotic stress tolerance, thus providing a large chemical portfolio for optimizing crop resistance, yield, and biofuel composition. Leveraging these preliminary data, we propose to generate a genome-wide map of the switchgrass terpene metabolic network through multi-gene co-expression analyses that allow the efficient cross-validation of TPS and P450 functions. Key enzymes would further be applied to structure-function studies via X-ray protein crystallography, homology modeling and site-directed mutagenesis to gain mechanistic insight into the catalytic specificity of switchgrass terpene metabolism and provide gene and amino acid targets for genome editing. In tandem with terpene pathway discovery, system-wide metabolomics, transcriptomics and proteomics studies in switchgrass accessions of contrasting drought tolerance would define the role of switchgrass terpene metabolism in conferring abiotic stress resilience. Metabolic changes would be assessed in a combined approach of targeted (terpenes) and untargeted metabolite profiling using a high-resolution LC-MS/MS approach, differential gene expression analyses through multiplexed Illumina RNA sequencing, and quantitative analysis of high-priority pathway enzymes using multiple reaction monitoring (MRM). Drawing on these insights, knock-down/out mutants of stress-associated pathway nodes would be generated by optimizing transient virus-induced gene silencing (VIGS) and CRISPR/Cas9 systems under control of the Tobacco Rattle Virus (TRV). The resulting mutant lines would then be analyzed for stress susceptibility and the impact on the root microbiome to define gene functions in planta. Knowledge of terpene pathways, enzyme mechanisms and bioactivities would be applied to enhance switchgrass stress resilience and to tailor-make terpene blends for biofuel production. Here, TRV-enabled CRISPR/Cas9 genome editing, including allele-specific knock-out of redundant genes, engineering of enzyme specificity via structure-guided point mutations, and overexpression of terpene genes relevant to stress-protection or biofuel production, would be used to increase metabolic flux toward desired pathways. Broader Impacts - Integrating the system-wide discovery, mechanistic analysis and non-transgenic genome engineering of the switchgrass terpene network aligns the required steps to unlock the chemical potential of this important metabolite class to generate crops that are more resistant to stress and provide advanced biofuel production in light of rising climate pressures as foreseeable challenges for bioenergy crop cultivation. The proposed project would further offer interdisciplinary student training through active involvement in the project and integration of research concepts and outcomes into newly-developed graduate and undergraduate courses on Plant Biotechnology.

09 BIOMASS FUELS↗

An Analytical Approach to the Design of an Automatic Discontinuous Control System

An analytical investigation was conducted concerning the design of an attitude-stabilization system for stabilizing a vehicle experiencing negligible external moments. The system studied was an automatic discontinuous control system employing a linear switching function including effects of pure time delays, rise and decay time, and neutral zone. Equations were developed which generalize the transient and limit-cycle performance of the control system. understanding of how the physical constants of the system affect its performance, the equations enable the optimization of the system with regard to most considerations that can be expressed mathematically. Design charts are presented which enable rapid calculation of the best thrust level and switching-function coefficient for minimizing power required to stabilize the vehicle within some amplitude, minimizing attitude error, and minimizing angular-velocity error after a period of operation.

Taylor, Lawrence W., Jr.↗

Identification of nonlinear system parameters in joints using the force-state mapping technique

A procedure is presented for identifying the potentially strong nonlinear properties of structural members, such as joints, by expressing the force transmitted by the member as a function of its mechanical state. By explicitly including position and rate dependent effects, the surface of transmitted force versus state, the force-state map, has distinct, unique, superposable features for common structural nonlinearities, even those which appear to indicate hysteresis on a force-stroke presentation. An analysis is performed on the influence of true memory effects, transient response, and uncertainty in the measurements and system mass on the precision of the procedure. The successful identification of simulated data verifies the accuracy of the identification algorithm. Tests are then conducted on three actual joint models, with incomplete state measurements typical of an actual testing environment. The ability of the procedure to estimate the complete state vector and to analyze and reconstruct the measured nonlinear characteristics is demonstrated.

Crawley, E. F.↗

Impacts in Ice: Commissions of Solar System Crater Populations

The classical phases of cratering are compression, excavation, and modification. Recent theory, however, supports and alternative sequence of physical events: (1) coupling - energy and momentum are transferred, and the cratering flow field is set up; (2) power-law-growth the flow field expands, with transient cavity dimensions expressible as a simple power law function of time; and (3) late phase - some combination of gravity, strength, and viscosity limits cavity growth, initially causing a deviation from power-law behavior and eventually determining the size and shape of the final (transient) crater. The dominant mechanism that limits cavity growth defines a cratering regime and a single variable, the coupling parameter, determines the scaling laws in the various regimes. The coupling parameter is intermediate in dimensionality between energy and momentum and its exact form is determined. For simple materials with rate and scale independent strength, the transition crater diameter between the strength and gravity regimes is, within reasonable bounds, independent of velocity. Even the smallest craters observed by Voyager appear to be gravity dominated.

Mckinnon, W. B.↗

Theoretical investigations on plasma processes in the Kaufman thruster

An analysis of the sputtering of metal surfaces and grids by ions of medium energies is given and it is shown that an exact, nonlinear, hyperbolic wave equation for the temperature field describes the transient transport of heat in metals. Quantum statistical and perturbation theoretical analysis of surface sputtering by low energy ions are used to develop the same expression for the sputtering rate. A transport model is formulated for the deposition of sputtered atoms on system components. Theoretical efforts in determining the potential distribution and the particle velocity distributions in low pressure discharges are briefly discussed.

Wilhelm, H. E.↗

Optimization of Heterologous Glucoraphanin Production In Planta

Glucoraphanin is a plant specialized metabolite found in cruciferous vegetables that has long been a target for production in a heterologous host because it can subsequently be hydrolyzed to form the chemopreventive compound sulforaphane before and during consumption. However, previous studies have only been able to produce small amounts of glucoraphanin in heterologous plant and microbial systems compared to the levels found in glucoraphanin-producing plants, suggesting that there may be missing auxiliary genes that play a role in improving production in planta. Here, in an effort to identify auxiliary genes required for high glucoraphanin production, we leveraged transient expression in Nicotiana benthamiana to screen a combination of previously uncharacterized coexpressed genes and rationally selected genes alongside the glucoraphanin biosynthetic pathway. This strategy alleviated metabolic bottlenecks, which improved glucoraphanin production by 4.74-fold. Our optimized glucoraphanin biosynthetic pathway provides a pathway amenable for high glucoraphanin production.

59 BASIC BIOLOGICAL SCIENCES↗