SEARCH · Engineering Papers

Results for “temperature programmed desorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗

DOE OSTI2024

Bond Selective Photochemistry at Metal Nanoparticle Surfaces: CO Desorption from Pt and Pd

The use of visible photon fluxes to influence catalytic reactions on metal nanoparticle surfaces has attracted attention based on observations of reaction mechanisms and selectivity not observed under equilibrium heating. These observations suggest that photon fluxes can selectively impact the rates of certain elementary steps, creating nonequilibrium energy distributions among various reaction pathways. However, quantitative studies validating these hypotheses on metal nanoparticle surfaces are lacking. Here, we examine the influence of continuous wave visible photon fluxes on the CO desorption rates from 1 to 2 nm diameter Pt and Pd nanoparticle surfaces supported on γ-Al 2 O 3 . Temperature-programmed desorption measurements quantified via diffuse reflectance infrared Fourier transform spectroscopy demonstrate that visible photon fluxes significantly enhanced the rate of CO desorption from Pt nanoparticles in a wavelength-dependent manner. 440 nm photons most efficiently promoted CO desorption from Pt nanoparticle surfaces, aligning with the excitation energy for the interfacial electronic transition within the Pt–CO bond. Conversely, visible photon fluxes had no measurable influence on CO desorption rates from Pd nanoparticle surfaces after accounting for photon-induced heating. Density functional theory calculations demonstrate that the Pt–CO bond exhibits a narrower LUMO resonance, stronger coupling between the photoexcitation and forces induced on the metal–C bond, and vibrational energy dissipation that more effectively couples to desorption as compared to Pd–CO. These results demonstrate the specificity photons provide in facilitating chemical reactions on metal nanoparticle surfaces and substantiate the idea that photon fluxes can steer processes and outcomes of catalytic reactions in ways not achievable by equilibrium heating.

desorption↗

DOE OSTI2025

Mechanistic insights into N 2 O formation as a side product in NH 3 -SCR over small pore Cu-zeolites

Here, the present contribution provides clarity to N 2 O formation mechanisms and key influencing factors during low temperature NH 3 -SCR, with the goal of enabling the rational design of advanced SCR catalysts with low greenhouse gas impact. By studying more than 50 small pore Cu-exchanged zeolite SCR catalyst samples, including model catalysts synthesized in our laboratories and state-of-the-art industrial catalysts, we explored a wide range of factors affecting N 2 O formation. These factors included Cu loading, support Si/Al ratio, support topology, catalyst aging, reaction temperature and reactant feed composition effects. We probed N 2 O formation under both steady-state SCR, and during NH 4 NO 3 decomposition via temperature programmed desorption (TPD). Finally, we used DFT to probe energetics of possible N 2 O formation pathways. Based on these studies, we confirm that low temperature N 2 O formation occurs via multiple reaction pathways that all involve NH 4 NO 3 and are supported by Cu moieties that facilitate in-situ NO oxidation to NO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Ba₁₋ₓSrₓFeO₃₋ᵧ as an Improved Oxygen Carrier for Chemical Looping Air Separation: A Computational and Experimental Study

Chemical looping air separation (CLAS) is a promising method to generate pure carbon-dioxide from fuel combustion with a pure oxygen stream, which is produced through the capture, and targeted release, of oxygen from the atmosphere using a solid oxide carrier. The performance of this process depends on the redox characteristics of the oxide carrier. Using experimental oxygen-temperature-programmed desorption (TPD) and thermogravimetric analysis (TGA), the study shows that Ba₀․₇₅Sr₀․₂₅FeO₃ has improved oxygen storage capacity (OSC), oxidation, and reduction kinetics over pristine SrFeO₃ at temperatures ranging from 300-500 °C. The redox energetics computed by using first-principles density functional theory (DFT) calculations also depict the measured trend establishing it as an important descriptor of the measured performance. The Ba₁₋ₓSrₓFeO₃₋ᵧ depicts a Sr-substitution and oxygen stoichiometry induced structural phase transition from hexagonal at low temperatures to pseudo-cubic phase with higher OSC up to T=400 °C. Also, the mechanism leading to this structural phase transition is identified by performing electronic and vibrational structural calculations. This presentation was given on March 8, 2024 at the APS March Meeting in Minneapolis, MN.

Acharya, Shree Ram↗

DOE OSTI2025

Structure–Activity Relationships for Ethanol Dehydrogenation to Acetaldehyde by Silica-Supported Zinc Oxide Catalysts

Silica-supported ZnO efficiently catalyzes the nonoxidative dehydrogenation of ethanol to acetaldehyde, which is relevant for production of 1,3-butadiene from bioethanol. Characterization with in situ spectroscopies under dehydrated conditions (high sensitivity-low energy ion scattering (HS-LEIS), diffuse reflectance (DR) UV–vis, X-ray absorption spectroscopy (XAS), diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS), inelastic neutron scattering (INS), and UV Raman), and ammonia adsorption probed by temperature-programmed desorption followed by DRIFTS and mass spectrometry (DRIFTS-MS NH 3 -TPD), and DFT calculations revealed that the supported ZnO x phase was present as isolated surface ZnO x sites on SiO 2 , with the vast majority coordinated by two siloxane bonds and one silicon atom with two nonbridging oxygens ((≡SiO) 2 Zn 2+ O 2 Si=), anchored at 4-, 5-, and 6-membered siloxane rings. A minor fraction of surface ZnO x sites possessed Lewis acidity, and even fewer sites possessed a Bro̷nsted acidic Zn(OH) + Si moiety. Ethanol temperature-programmed surface reaction-mass spectrometry (TPSR-MS) with various oxidative or ethanol reaction pretreatments indicated that only sites with Lewis and Bro̷nsted acidic character (Zn(OH) + Si) were active for ethanol dehydrogenation, while the majority surface (≡SiO) 2 Zn 2+ O 2 Si= sites were inactive. Greater heterogeneity among all surface ZnO x sites, as assessed by in situ DR UV–vis spectroscopy, was associated with a greater number of ZnO x sites that were active for ethanol dehydrogenation as well as lower enthalpic barriers for acetaldehyde production among the most active surface ZnO x sites. Turnover frequencies and the apparent activation energy for ethanol dehydrogenation were determined from steady-state kinetics. Together, these findings suggested that anchoring inactive surface (≡SiO) 2 Zn 2+ O 2 Si= sites on the silica support caused a greater number of active surface ZnO x sites to adopt a more strained configuration, promoting ethanol dehydrogenation catalysis. Pretreatments and catalysts that promoted desorption of ethanol during TPSR, taken as a marker of surface dehydroxylation, were associated with an increased number of the most active surface (Zn(OH) + Si) sites. Such findings suggested that inactive surface ZnO x sites were activated for ethanol dehydrogenation by dehydroxylation of the support and/or decreased coordination to hemilabile siloxane ligands.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Correlating binding energies of adsorbed CO and H on model surfaces with CO/H 2 selectivity from co-electrolysis of CO 2 and H 2 O over copper–palladium bimetallic catalysts

Binding energies of adsorbed CO and H are key descriptors governing the activity and selectivity of the co-electrolysis of CO 2 and H 2 O to produce syngas with desired CO/H 2 ratios. Palladium hydride (PdH), which forms in situ at negative overpotentials, has been identified as the active Pd phase for CO 2 reduction to syngas. Herein, binding energies of CO and H are determined using temperature programmed desorption (TPD) of CO and H 2 from Pd(111), PdH/Pd(111), and Cu/PdH/Pd(111) under ultra-high vacuum (UHV) conditions. TPD results reveal that desorption of H 2 from subsurface PdH occurs at 460 K, while desorption from surface PdH is more facile at 320 K. CO desorption temperatures shift 20 K lower on PdH/Pd(111) compared to on Pd(111). The presence of 0.7 ML Cu further increases the desorption temperature of H 2 by 30 K while simultaneously reducing CO desorption temperatures by 70 K. Density functional theory (DFT) calculations show that CO adsorption onto Pd sites is hindered on the 0.7 ML Cu/PdH/Pd(111) surface while the kinetic barrier for H 2 desorption is increased. The trends in the binding energies of CO and H on model surfaces are consistent with electrochemical measurements of CuPd powder catalysts in a membrane electrode assembly (MEA), where H 2 evolution is reduced while CO production is enhanced compared to unmodified Pd catalysts. Overall, the results from model surface studies (TPD and DFT) provide a prediction and explanation for the activity and CO/H 2 ratios observed in electrochemical experiments. This study also demonstrates that CuPd is a promising catalyst with reduced Pd-loading to produce CO-rich syngas.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Low temperature ethanol steam reforming: Selectivity control with lithium doping of Pt/m-ZrO 2

Lithium promoted 2%Pt/m-ZrO 2 catalysts previously observed to exhibit higher rates for the low temperature water-gas shift (LTS) were tested for the ethanol steam reforming with the aim of exploring the potential tuning of the selectivity. Characterization of catalysts having optimized Li content (0.5–0.75%Li) for LTS exhibited (a) weakened C—H bonding of formate, a proposed intermediate in the LTS mechanism, as shown by a shift in the ν(CH) band to lower wavenumbers, (b) a relatively low extent of blocking of Pt, as measured by the ν(CO) band intensity of Pt-CO, (c) increased basicity as measured by CO 2 temperature-programmed desorption with mass spectrometry, but not so high as to strongly inhibit CO 2 product removal, and finally (d) no evidence of electron transfer from Li to Pt. Here, for this study, the same catalysts were tested for ethanol steam reforming (ESR). Results show that Li could likewise weaken the C—C bond of the acetate intermediate, the analog of formate in LTS, and facilitate decarboxylation over decarbonylation altering the selectivity in favor of methanation. This trend was confirmed by fixed bed reaction testing, in-situ infrared spectroscopy experiments of transient ESR, and temperature-programmed ESR using MS. The Li-doped catalysts may be used to pre-reform ethanol prior to feeding to a methane steam reformer to increase the overall H 2 selectivity of the process. DRIFTS of steady state ESR revealed that deactivation occurs through losses in the Pt-support interface, thereby hindering the turnover of the acetate intermediate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Na Promotion of Pt/m-ZrO 2 Catalysts for the Steam Reforming of Formaldehyde

The decomposition selectivity of formaldehyde during steam reforming was explored using unpromoted and sodium promoted Pt/m-ZrO 2 catalysts, and the Na content was varied (0.5%Na, 1%Na, 1.8%Na, 2.5%Na, and 5%Na). In situ DRIFTS experiments during temperature programmed reaction in flowing H 2 O revealed that formaldehyde is adsorbed at reduced defect sites on zirconia, where it is converted to formate species through the addition of labile bridging OH species. Formate species achieve a maximum intensity in the range of 125–175 °C, where only slight changes in intensity are observed. Above this temperature, the formate decomposition reactivity strongly depends on the Na loading, with the optimum loadings being 1.8%Na and 2.5%Na. CO 2 temperature programmed desorption results, as well as a greater splitting observed between the formate ν asym (OCO) and ν sym (OCO) bands in infrared spectroscopy, indicate greater basicity is induced by the presence of Na. This strengthens the interaction between the formate -CO 2 functional group and the catalyst surface, weakening the formate C-H bond. A shift in the ν(CH) band of formate to lower wavenumbers was observed by addition of Na, especially at 1.8%Na and higher loadings. This results in enhanced decarboxylation and dehydrogenation of formate, as observed in in situ DRIFTS, temperature-programmed reaction/mass spectrometry experiments of the steam reforming of formaldehyde, and fixed bed reaction tests. For example, 2.5%Na addition of 2.5% increased the CO 2 selectivity from 83.5% to 99.5% and the catalysts achieved higher stable conversion at lower temperature than NiO catalysts reported in the open literature. At 5%Na loading, Pt sites were severely blocked, hindering H-transfer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Removal of deuterium retained in boron powder by oxygen or high-temperature bakeout

Fuel retention in dust accumulated in fusion devices is a potential operational hazard. Boronization is one of the leading wall-conditioning candidates for future fusion devices. Fuel retention characteristics of boron dust must be studied to accurately understand the potential hazards of boron dust in fusion devices. We evaluated the retention of deuterium (D) in commercially available boron powder as a proxy for tritium retention in boron dust. Diffuse reflectance infrared Fourier transform spectroscopy revealed that boron powder between 300 and 500 K exposed to neutral hydrogen (H 2 ) gas retains H via B-H bonding. We utilized D 2 exposures of 17,400 L on the boron powder, which led to retention on the order of 0.5 g D per 100 kg B or 1.2 g D per m 2 B, as estimated from temperature programmed desorption measurements. We evaluated how powder bakeouts under ultra-high vacuum (UHV), or in an oxygen (O 2 ) or H 2 gas backfilled environment can remove the retained fuel. Bakeouts below 523 K under UHV exhibited poor D removal, promoting recapture of D 2 present as background gas in the chamber. Higher temperature bakeouts led to the removal of over 80% of the retained D within 3 days (623 K) or 1 h (723 K). Bakeouts at 423 K under an O 2 gas environment removed ∼150% more retained D from the boron powder, when compared to bakeouts conducted under UHV. These results suggest that efficient fuel removal from boron dust can be achieved by high-temperature bakeout (>623 K) or by bakeouts at lower temperature (423 K) under an O 2 environment.

Bakeout↗

DOE OSTI2025

Experimental Setup to Investigate Hydrogen Isotope Retention on Powder Samples as Slag/Dust Proxies for Advanced Fusion Reactors

Slag/dust formation is one of the critical issues regarding tritium retention in advanced fusion reactors. We upgraded an ultrahigh vacuum device, the sample exposure station (SES), to perform temperature-programmed desorption (TPD), also known as thermal desorption spectroscopy, to investigate deuterium (D) retention in powder samples that are utilized as proxies for slag/dust particles formed in fusion reactors. TPD analysis, calibrated for the desorption rate, was successfully performed on commercially available crystalline/amorphous boron (B) powder after D 2 neutral gas or D + ion exposure. We calibrated the B powder temperature measurement for TPD analysis utilizing a D 2 desorption peak from B-D bonding known for its desorption temperature ~700 K. We introduce a separation procedure of observed D TPD signals, convoluted for corresponding D retention pathways, that was necessary for TPD analysis. This is the first report on the retention of D 2 neutral gas to B, and this observation was enabled by utilizing the B powder sample, which has a larger surface area than films commonly used in laboratory experiments. In conclusion, the upgraded SES system will enable us to investigate hydrogen isotope behaviors for powder/dust samples of various elemental compositions, including metals.

Plasma-facing component debris↗

DOE OSTI2025

Role of Polymer Architecture in CO 2 Capture from Air Using Supported Poly(alkylenimine)s: Linear vs Branched Polymers

Direct air capture (DAC) of CO 2 coupled with geologic storage is a promising climate change mitigation strategy, with some applications employing amines supported on porous solids as CO 2 sorbents. While branched poly(ethylenimine) (PEI) is the standard benchmark amine material, it suffers from limited oxidative stability. Poly(propylenimine) (PPI), as an alternative, has previously demonstrated improved resistance to degradation under harsh oxidative conditions. Linear and branched PEI are commercially available, though at different molecular weights, while PPI is not commercially available. For this reason, a comparative study of all four polymers (linear PEI, branched PEI, linear PPI, branched PPI) has not been reported for DAC. In this study, we synthesize and compare low-molecular-weight (∼800 g/mol) linear (L) and branched (B) PEI and PPI supported on a model support, SBA-15 silica. These materials are evaluated for CO 2 adsorption under dry, DAC-relevant conditions (400 ppm of CO 2 , 30 °C). LPPI exhibited the highest amine efficiency at all loadings, reaching a maximum of 0.14 mmol CO 2 /mmol N, outperforming BPEI, while LPEI consistently showed the lowest uptake capacity. Temperature-programmed desorption reveals that the structure of the amine polymer impacts the CO 2 binding strength, with branched polymers displaying higher desorption energies of 102−111 kJ/mol. In situ infrared spectroscopy experiments show that all sorbents preferentially capture CO 2 as ammonium carbamate. Isobaric CO 2 uptake studies further underscore the influence of polymer mobility and support pore crowding on performance, while demonstrating the sorbents’ performance at elevated temperatures and CO 2 concentrations. All materials demonstrated good stability over 25 adsorption−desorption cycles using thermal regeneration in an inert gas purge, with only BPPI displaying a 10−11% decrease in capacity/amine efficiency during cycling, possibly due to the loss of low molecular weight, oligomeric amines. This is the first side-by-side comparison of the CO 2 sorption properties of linear and branched PEI and PPI with similar molecular weights. These findings highlight the significant role of polymer architecture in CO 2 capture efficiency and inform future designs of durable, high-performance DAC sorbents.

adsorbents↗

DOE OSTI2022

An Unbalanced Battle in Excellence: Revealing Effect of Ni/Co Occupancy on Water Splitting and Oxygen Reduction Reactions in Triple–Conducting Oxides for Protonic Ceramic Electrochemical Cells

Porous electrodes that conduct electrons, protons, and oxygen ions with dramatically expanded catalytic active sites can replace conventional electrodes with sluggish kinetics in protonic ceramic electrochemical cells. In this work, a strategy is utilized to promote triple conduction by facilitating proton conduction in praseodymium cobaltite perovskite through engineering non-equivalent B-site Ni/Co occupancy. Surface infrared spectroscopy is used to study the dehydration behavior, which proves the existence of protons in the perovskite lattice. The proton mobility and proton stability are investigated by hydrogen/deuterium (H/D) isotope exchange and temperature-programmed desorption. It is observed that the increased nickel replacement on the B-site has a positive impact on proton defect stability, catalytic activity, and electrochemical performance. This doping strategy is demonstrated to be a promising pathway to increase catalytic activity toward the oxygen reduction and water splitting reactions. The chosen PrNi 0.7 Co 0.3 O 3–δ oxygen electrode demonstrates excellent full-cell performance with high electrolysis current density of –1.48 A cm –2 at 1.3 V and a peak fuel-cell power density of 0.95 W cm –2 at 600 °C and also enables lower-temperature operations down to 350 °C, and superior long-term durability.

08 HYDROGEN↗

DOE OSTI2024

Preparation and Characterization of Materials for Low- to Intermediate-Temperature CO2 Adsorption

Global carbon dioxide emissions are rising and the use of fossil fuels in several sectors are the leading causes. As global population and economies continue to grow significantly, the most practical method of lowering such emissions is to capture CO2. Although other technologies are more developed, adsorption is very promising and has attracted much attention. To ensure this technology’s success, it is essential to have suitable CO2 adsorbent materials. In this work, several new hydrotalcites (HTs) with different initial concentrations of ion precursors were prepared for the first time by the co-precipitation method—it was possible to verify that the ion concentrations influence the characteristics of the materials. The prepared HTs were characterized by thermogravimetric analysis (TG), X-Ray diffraction (XRD), surface area measurements and temperature-programmed desorption of CO2 (TPD-CO2) to relate their CO2 capture capacity to their physicochemical properties; the CO2 adsorption equilibrium isotherms were determined at 35 and 300 °C for the prepared samples, as well as for some commercial materials: magnesium oxide, calcium oxide, aluminium oxide and Zeolite 13X. After determining which materials present the best CO2 adsorption capacity, these were submitted to adsorption-desorption cycles to study their stability. The main objective of the work was to prepare and study different CO2 adsorbents for processes that are carried out at low and intermediate temperatures. From the experimental results, it was possible to conclude that the Zeolite 13X showed the best capacity at 35 °C, 3.38 mmol·g−1 (@ pCO2 = 1 bar), and a prepared calcined HT (c-HT2) was the best at 300 °C, 0.97 mmol·g−1 (@ pCO2 = 1 bar). Moreover, it seems there is an optimum initial concentration of the ions’ solutions for the tested HTs, which depends on the final application—c-HT1 showed a better capacity at 35 °C and c-HT2 at 300 °C. From the adsorption-desorption cycles—performed at 35 and 300 °C with the best materials using a magnetic suspension microbalance at 1 bar of CO2 partial pressure —, a working cyclic capacity of 2.69 mmol∙g−1 was achieved by the Zeolite at 35 °C; in turn, c-HT2 showed a working cyclic capacity of 0.79 mmol∙g−1 at 300 °C.

Figueiredo, Anabela↗

DOE OSTI2025

The Surface Chemistry of Methanol on TiO 2 (110): Effects of Pressure and Temperature on the Stability of C–O and C–H Bonds

Synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the surface chemistry of methanol on TiO 2 (110), examining the effects of methanol pressure, oxide temperature, and coadsorption with H 2 . At 300 K, the adsorption of methanol on TiO 2 (110) leads to the formation of CH 3 O on the surface with a minor amount of CH 3 OH present. The easy cleavage of the O–H bond in the alcohol agrees with the predictions of theoretical calculations, and most of the adsorbed CH 3 O was not associated with the presence of Ti 3+ sites in the oxide substrate. The adsorbed CH 3 O was removed from the TiO 2 (110) surface by heating to 600 K without the deposition of CH x fragments or C on the oxide. The results of temperature-programmed desorption (TPD) showed the evolution of methanol and formaldehyde at 360 and 490 K as a result of a disproportionation reaction: 2CH 3 O → CH 3 OH + CH 2 O. This surface chemistry, where there is no rupture of the C–O bond, and only selective cleavage of O–H and C–H bonds, is very different from that found on metals used in catalysts for methanol reforming, where massive conversion of the alcohol into CO, CH x and C species is seen. Furthermore, the TPD data indicate that any CH 3 O formed on the oxide surface can be hydrogenated and desorbed as CH 3 OH at temperatures below 550 K. In this respect, titania is an ideal support for catalysts employed to achieve methanol synthesis through CO 2 hydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Ba 1−x Sr x FeO 3−δ as an improved oxygen storage material for chemical looping air separation: a computational and experimental study

Chemical looping air separation (CLAS) is a promising technology to generate oxygen-rich gas streams to enable efficient carbon dioxide capture during fossil fuel combustion or gasification. CLAS relies on the capture and release of oxygen from the atmosphere using the redox properties of an oxygen-selective solid oxide carrier. This study investigates the redox characteristics of Ba 1−x Sr x FeO 3−δ (0.0 ≤ x ≤ 0.417, 0.0 ≤ δ ≤ 0.5) using a combination of density functional theory (DFT) calculations and experimental verification using X-ray diffraction, thermogravimetric analysis, and oxygen-temperature-programmed desorption. The DFT computed energies of the Ba 1−x Sr x FeO 3−δ perovskites reveal a composition-dependent transition from hexagonal to cubic phases as the Sr-concentration or oxygen vacancy concentration increases. Oxygen vacancy formation energies of the cubic perovskites are found to be lower than those of their hexagonal counterparts. A low oxygen diffusion barrier of ∼1 eV combined with the thermodynamic preference of Ba 1−x Sr x FeO 3−δ compositions that form in a cubic phase suggests them as promising candidates for oxygen storage applications. The experimental results corroborate this finding by identifying Ba 0.75 Sr 0.25 FeO 3−δ in the cubic phase as an optimal composition offering low-temperature oxygen storage capacities comparable to that of the state-of-the-art Sr 0.75 Ca 0.25 FeO 3−δ perovskite oxygen storage material at 325 °C and 350 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Methanol Partial Oxidation on Cu(111) and PtCu(111) Single-Atom Alloy Surfaces: Effect of Surface Oxygen Coverage on Selectivity

The selective oxidation of methanol to formaldehyde on Cu surfaces is an important and well-studied reaction. However, a systematic analysis of product selectivity as a function of oxygen coverage on Cu(111) and Cu-based single-atom alloys (SAAs) has not been previously reported. In this work, we present a comprehensive investigation of deuterated methanol (CD 3 OH) partial oxidation on Cu(111) and 1% PtCu(111) SAA surfaces as a function of preadsorbed oxygen coverage. Temperature-programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS) reveal that isolated Pt atoms inhibit the initial surface oxidation of Cu(111) under low oxygen exposures. Despite this difference in oxidation kinetics, the product selectivity remains largely unaffected: on both Cu(111) and PtCu(111), formaldehyde (CD 2 O) is the predominant partial oxidation product over a broad range of oxygen coverages. The selectivity toward formaldehyde peaks at intermediate oxygen coverages (∼0.3 monolayers, ML), indicating the existence of an optimal oxygen loading for partial oxidation. Notably, the similar product selectivities on Cu(111) and PtCu(111) over a range of surface oxygen coverage indicate that Pt single atoms do not significantly alter the reaction pathway or shift the optimal oxygen coverage for formaldehyde formation. Control experiments confirm that Cu(111) is unreactive toward methanol in the absence of oxygen, while PtCu(111) surfaces produce a small amount of formaldehyde even when oxygen is not preadsorbed, indicating that isolated Pt atoms facilitate O−H activation at below 150 K, leading to H 2 desorption, followed by C−D activation at higher temperatures (∼350 K). Density functional theory (DFT)-based calculations show that Pt atoms increase the O 2 dissociation barrier relative to Cu(111), consistent with the observed inhibition of oxidation at low exposures. Overall, this work provides the first detailed selectivity map for methanol oxidation on oxidized Cu(111) and PtCu(111) SAA surfaces. By linking classical mechanistic insights such as methoxy- and formate-mediated pathways with single-atom alloy catalyst design, this work demonstrates that while Pt substitution modulates the oxidation kinetics and oxygen binding, the overall selectivity toward formaldehyde is governed primarily by oxygen coverage. These findings underscore the potential of isolated dopants to tune surface oxidation behavior without compromising the intrinsic partial oxidation selectivity of copper-based catalysts.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Assessing the Performance of Exchange‐Correlation Density Functionals in Describing the Iron‐Catalyzed Ammonia Synthesis System

Density functional theory (DFT) has been widely employed for elucidating mechanistic aspects of heterogeneous catalysis. However, the accuracy of DFT calculations relies heavily on selecting an exchange-correlation (XC) functional that correctly describes the electronic structure of materials involved in the reactions. This study assesses the accuracy of several XC density functionals for modeling the iron-catalyzed ammonia synthesis system. In the assessment of functional accuracy, experimental references are compared to DFT-calculated values for the formation energy of gas-phase ammonia and nitrogen, bulk Fe/Fe-nitride (γ′-Fe 4 N) lattice constants and cohesive/formation energies, and nitrogen and ammonia binding energies on Fe(100), Fe(111), Fe(110), and γ′-Fe 4 N(111). It is observed that the experimental value for each of these descriptors is accurately modeled by at least one functional. RPBE alone provides reliable estimates for both the lattice constant and cohesive energy of Fe and γ′-Fe 4 N. Temperature-programmed desorption experiments led to estimates for N and NH 3 adsorption across several Fe-based facets that are best captured by RPBE. These results highlight the importance of choosing an appropriate XC functional that accurately describes experimental systems and offer insights into effectively modeling the interactions between nitrogen and ammonia on Fe-based surfaces.

adsorption↗

DOE OSTI2023

Surface‐modified Ag@Ru‐P25 for photocatalytic CO 2 conversion with high selectivity over CH 4 formation at the solid–gas interface

Systematic optimization of the photocatalyst and investigation of the role of each component is important to maximizing catalytic activity and comprehending the photocatalytic conversion of CO 2 reduction to solar fuels. A surface-modified Ag@Ru-P25 photocatalyst with H 2 O 2 treatment was designed in this study to convert CO 2 and H 2 O vapor into highly selective CH 4 . Ru doping followed by Ag nanoparticles (NPs) cocatalyst deposition on P25 (TiO 2 ) enhances visible light absorption and charge separation, whereas H 2 O 2 treatment modifies the surface of the photocatalyst with hydroxyl (–OH) groups and promotes CO 2 adsorption. High-resonance transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray absorption near-edge structure, and extended X-ray absorption fine structure techniques were used to analyze the surface and chemical composition of the photocatalyst, while thermogravimetric analysis, CO 2 adsorption isotherm, and temperature programmed desorption study were performed to examine the significance of H 2 O 2 treatment in increasing CO 2 reduction activity. The optimized Ag 1.0 @Ru 1.0 -P25 photocatalyst performed excellent CO 2 reduction activity into CO, CH 4 , and C 2 H 6 with a ~95% selectivity of CH 4 , where the activity was ~135 times higher than that of pristine TiO 2 (P25). For the first time, this work explored the effect of H 2 O 2 treatment on the photocatalyst that dramatically increases CO 2 reduction activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗