Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Analysis of Niobium Electropolishing Using a Generalized Distribution of Relaxation Times Method

Using electrochemical impedance spectroscopy, we have devised a method of sensing the microscopic surface conditions on the surface of niobium as it is undergoing an electrochemical polishing (EP) treatment. The method uses electrochemical impedance spectroscopy (EIS) to gather information on the surface state of the electrode without disrupting the polishing reaction. The EIS data is analyzed using a so-called distribution of relaxation times (DRT) method. Using DRT, the EIS data can be deconvolved into discrete relaxation time peaks without any a priori knowledge of the electrode dynamics. By analyzing the relaxation time peaks, we are able to distinguish two distinct modes of the EP reaction. As the polishing voltage is increased, the electrode transitions from the low voltage EP mode, characterized by a single relaxation time peaks, to the high voltage EP mode, characterized by two relaxation time peaks. We theorize that this second peak is caused by the formation of an oxide layer on the electrode. We also find that this oxide induced peak transitions from to a negative relaxation time, which is indicative of a blocking electrode process. By analyzing EPed samples, we show that samples polished in the low voltage mode have significantly higher surface roughness due to grain etching and faceting. We find that the surface roughness of the samples only improves when the oxide film peak is present and in the negative relaxation time region. This shows that EIS combined with DRT analysis can be used to predict etching on EPed Nb. This method can also be performed before or during the EP, which could allow for adjustment of polishing parameters to guarantee a smooth cavity surface finish.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Investigation of N 2 /O 2 plasma interaction with Pt-catalyst: effect of metastable adsorbates on product hysteresis

The coupling of catalysts and atmospheric-pressure plasma has the potential to improve the efficiency of certain catalytic reactions. Understanding the changes that the catalyst surface undergoes during exposure to plasma is key to improving plasma–catalytic performance. In this work, long term exposure of Pt–Al 2 O 3 powder catalyst to an Ar/N 2 /O 2 non-equilibrium atmospheric-pressure plasma-jet was investigated. Products produced by the interaction were analyzed downstream with Fourier-transform infrared spectroscopy while surface species were analyzed operandi with diffuse reflectance infrared Fourier transform spectroscopy. During exposure, the catalyst temperature was ramped cyclically between 100 °C and 350 °C to understand how substrate temperature affects the plasma–catalyst interaction. Long-lasting changes were revealed to take place on the catalyst surface during plasma exposure. At low temperatures, Pt–O and Pt–NO accumulate on the surface which react at elevated temperatures to form NO 2 . NO 2 initially appears to spill on to the Al 2 O 3 support as nitrites and nitrates instead of desorbing. Stable surface conditions are only achieved after prolonged plasma exposure, when nitrate sites on the Al 2 O 3 support are filled. By changing the catalyst temperature at various rates, the impact of total plasma species flux to the surface was analyzed. It was found that decreasing the heating rate increased the hysteresis in the pattern of NO 2 formation during thermal cycling. The variation with temperature demonstrates that plasma exposure results in a buildup of surface NO x and oxygen species which react or desorb at high temperatures. The observed changes are discussed from the generic viewpoint that a non-equilibrium plasma interacting with a catalyst at low temperature introduces metastable steady-state surface conditions. Upon heating above a threshold temperature, the introduced surface modifications can change either due to thermal effects, or, for a plasma environment, by additional interaction with the incident plasma species flux. The surface/material changes take place in a highly predictable fashion and after sufficient time above the threshold temperature reach a steady-state condition that is different from the transient behavior that is observed during initial heating. During cooling the plasma-surface interaction exhibits a different behavior than during heating, and this results in hysteresis of diverse observables. The metastability/hysteresis description appears quite generic and analogous to hysteresis behavior seen for different systems. Furthermore, it is expected to be useful for understanding the consequences of plasma–catalyst surface interactions for various systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Analytical modeling and simulation of electrical contact resistance for elastic rough electrode surface contact including frictional temperature rise

An improved electrical contact resistance (ECR) model for elastic rough electrode contact is proposed, incorporating the effects of asperity interactions and temperature rise by frictional and joule heating. The analytical simulation results show that the ECR decreases steeply at the beginning of the contact between Al and Cu. However, it becomes stabilized after reaching a specific contact force. It is also found that the longer elapsed sliding contact time, the higher ECR due to the increase in electrical resistivity of electrode materials by the frictional temperature rise at the interface. The effects of surface roughness parameters on ECR are studied through the 3 2 full-factorial design-of-experiment analysis. Based on the two representative roughness parameters, i.e., root-mean-square (rms) roughness and asperity radius, their individual and coupled effects on the saturated ECR are examined. The saturated ECR increases with the rms roughness for a rough machined surface condition, but it is hardly affected by the asperity radius. On the other hand, the saturated ECR increases with both the rms roughness and the asperity radius under a smooth thin film surface condition.

42 ENGINEERING↗
DOE OSTI2021

Conditioning the Surface and Bulk of High-Nickel Cathodes with a Nb Coating: An In Situ X-ray Study

Surface coating is commonly employed by industries to improve the cycling and thermal stability of high-nickel (Ni) transition metal (TM) layered cathodes for their practical use in lithium-ion batteries. Niobium (Nb) coating or substitution has been shown to be effective in stabilizing LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes; in addition, the electrochemical performance of the final products varies depending on the postprocessing. In this follow-up study, we use in situ synchrotron X-ray diffraction to investigate the kinetic processes and the involved structural evolution in Nb-coated NMC811 upon heat treatment. Furthermore, quantitative structure analysis reveals thermally driven concurrent changes in the bulk and surface, in particular, the phase evolution of the coating layer and Nb/TM interdiffusion that facilitates penetration of Nb into the bulk and particle growth at the increased temperatures. Findings from this study highlight the new opportunities for the intended control of the structure and surface properties of high-Ni cathodes through surface coating in conjunction with postprocessing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Suppressed Daytime Convection Over the Amazon River

We investigated the interaction between surface conditions and precipitating convection by comparing the Amazon River against the surrounding forest. Despite similar synoptic conditions within a few tens of kilometers, the river surface is substantially cooler than the surrounding forest during the day and warmer at night. We analyzed 20 years of high-resolution satellite precipitation data and confirmed previous findings of daytime rainfall reduction over the river for the whole Amazon Basin. The percentage reduction is strongest during the dry-to-wet transition season. In addition, the percentage reduction of individual tributary is significantly correlated with the Laplacian of surface temperature, which causes thermally driven surface divergence and suppresses local convection. Additionally, nighttime rainfall is enhanced over tributaries near the Atlantic coast during the wet season. A regional climate model then simulates the local rainfall anomalies associated with the river. Above the river, moisture diverges near the surface and converges above the surface before the daytime rainfall, partially driven by the horizontal gradient of humidity. Unlike the river, moisture convergence within the boundary layer is more critical for the rainfall above the forest region. Our studies suggest that strong thermal contrast can be important in deriving heterogeneous convection in moist tropical regions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Gas delivery system for environmental transmission electron microscope

A portable, compact gas delivery system can support an environmental transmission electron microscope. Environment transmission electron microscopy provides researchers a unique capability of assessing a material's surface conditions at atomic resolution in a variety of reactive and oxidizing environments. The ability to precisely control the analysis chamber's environmental conditions over time is key to the success of a typical surface analysis. The gas delivery system provides the correct balance or pressure delivery precision, contamination control, and gas isolation.

Nogan, John Joseph↗
DOE OSTI2024

Integrated modeling of boron powder injection for real-time plasma-facing component conditioning

An integrated modeling framework for investigating the application of solid boron (B) powder injection for real-time surface conditioning of plasma-facing components (PFCs) in tokamak environments is presented. Utilizing the DIII-D impurity powder dropper (IPD) setup, this study simulates B powder injection scenarios ranging from milligrams to tens of milligrams per second, corresponding to boron flux rates of 10 20 –10 21 B/s in standard L-mode conditions. The comprehensive modeling approach combines EMC3-EIRENE for simulating the deuterium plasma background and the Dust Injection Simulator (DIS) for the ablation and transport of the boron powder particles. EMC3 trace impurity fluid modeling results show substantial boron transport to the inboard lower divertor, predominantly influenced by the main ion plasma flow. The dependency on powder particle size (5-250 µm) was found to be insignificant for the scenario considered. The effects of erosion and redeposition were considered to reconcile the discrepancies with experimental observations, which saw substantial deposition on the outer divertor plasma-facing components. For this purpose, the WallDYN3D code was updated to include boron sources within the plasma domain and integrated into the modeling framework. The mixed-material migration modeling shows evolving boron deposition patterns, suggesting the formation of mixed B-C layers or predominantly B coverage depending on the powder mass flow rate. While the modeling outcomes at lower B injection rates tend to align with DIII-D experimental observations, the prediction of near-pure boron layers at higher rates has yet to be experimentally verified in the carbon environment of the DIII-D tokamak. The extensive reach of boron layers found in the modeling suggests the need for modeling that encompasses the entire wall geometry for more accurate experimental correlations. This integrated approach sets a precedent for analyzing and applying real-time in-situ boron coating techniques in advanced tokamak scenarios, potentially extendable to ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Riverbed Temperature and 4D ERT Monitoring Reveals Heterogenous Horizontal and Vertical Groundwater-Surface Water Exchange Flows Under Dynamic Stage Conditions

Groundwater surface water exchange plays a critical role in physical, biological, and geochemical function of coastal and riverine systems. Observing exchange flow behavior in heterogeneous systems is a primary challenge, particularly when flows are governed by dynamic river stage or tidal variations. In this paper we demonstrate a novel application of time-lapse 3D electrical resistivity tomography and temperature monitoring where an array of thermistors installed beneath a riverbed double as resistivity electrodes. We use the array to monitor stage driven exchange flows over a 6-day period in a dynamic, stage-driven high order stream. We present a method for addressing the otherwise confounding effects of the moving river-surface boundary on the raw resistivity data, thereby enabling successful tomographic imaging. Temperature time-series at each thermistor location and time-lapse 3D images of changes in bulk electrical conductivity together provide a detailed description of exchange dynamics over a 10-meter by 45-meter section of the riverbed, to a depth of approximately 5 m. Results reveal highly variable flux behavior throughout the monitoring domain including both horizontal and vertical exchange flows.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Evaluation and Uncertainty of Radioxenon Transport with a Mesoscale Model after the February 2013 Underground Test in North Korea

Abstract The transport of radioxenon released from the February 2013 underground nuclear weapons test in North Korea was analyzed at two receptors—one at the Comprehensive Nuclear Test Ban Treaty site Rn58 in Russia (400 km downwind) and a second at Rn38 in Japan (1000 km downwind). Transport was modeled with two ensembles of mesoscale simulations, one generated with varying initial and lateral boundary conditions taken from the Global Forecasting System uncertainty ensemble, and a second created from different parameterizations and surface conditions. The wind variability was similar for the two ensembles and consistent with observations at 925 mb (1 mb = 1 hPa) but not at the surface. Biases in calculated surface winds and the radioxenon concentration in the ensembles were attributed mainly to poor simulation of the sea breeze at both locations and mountain lee affects at Rn38 in Japan. These wind regimes affected the timing of the surface radioxenon plume at Rn58 and its duration at Rn38. Surface wind variability induced by terrain and land–sea contrast (the sea breeze) also had a significant effect on the surface winds and plume dynamics, including blocking of flow approaching elevated terrain near Vladivostok and the west side of Japan. Increased plume uncertainty was seen at night because of surface wind variability. Measured surface chemical variability was larger than found in the first European Tracer Experiment in central Europe. The study found that horizontal model resolution contributes to uncertainty but not as much as vertical resolution, boundary layer parameterizations, and assimilation of surface meteorological data near the receptor.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Long‐Term Observations of Turbulence Vertical Velocity Spectra in a Convective Mixed Layer: Dependence on Land‐Surface Forcing in the U.S. Southern Great Plains

Doppler lidar vertical velocity retrievals were analyzed for the scale and structure of mixed-layer turbulence over a 7-year period, on fair-weather warm season days (442 cases) in the U.S. Southern Great Plains. Based on the hypothesized influence of land-surface forcing and updraft size on convective boundary layer clouds, a spectral analysis was performed to quantify effects of surface forcing (surface buoyancy flux, friction velocity, and evaporative fraction) on turbulence scale. Significant (order-of-magnitude) variations in spectral density were found in the energy-production subrange and mesoscale regimes. Integral scale decreased with increasing buoyancy flux (and Monin-Obukhov stability parameter), while spectral density in the energy-production subrange increased, implying a transition to buoyancy-driven cellular structures with narrower updrafts. The influence of stability parameter was limited to the neutral to convective transition, and could not explain the wide variation in spectral density in the mesoscale regime. However, high friction velocity (u* > 0.5 m s –1 ) was associated with larger integral scale (updraft width), and a greater portion of spectral density in the mesoscale regime. Lidar profiles and radar reflectivity for individual cases revealed evidence of roll and wave-like structures contributing to mesoscale variability on high friction velocity days, suggesting shear instabilities on days with wetter land surface conditions and smaller buoyancy flux. The role of friction velocity emphasizes the multivariate nature of surface influences on turbulence, and implies that variance-based turbulence closures may not be adequate for capturing effects of surface forcing on updraft size.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Effect of dielectric target properties on plasma surface ionization wave propagation

Surface ionization waves (SIWs) propagating along dielectric covered, grounded surfaces have been studied for various dielectric bulk and surface conditions; a dependence on the propagation velocity with respect to dielectric electrical thickness and near surface permittivity profiles are observed. SIWs generated by an atmospheric pressure plasma source are imaged interacting with planar dielectric surface. Surface wave velocity is obtained by tracking emission intensity as a function of time. Target dielectric thickness is varied from $d = 0.15-10$ mm and dielectric constant is varied from $\epsilon_r = 6.21 - 9.4$. The propagation of SIWs can be generally predicted by relating their velocity to the RC time constant of the circuit generated between the plasma and the dielectric surface, but it is found that this approximation breaks down for dielectric substrates of sufficient thickness and wave velocity becomes constant. The results show that wave velocity is stable and predictable for target thicknesses beyond a certain point determined by the permittivity of the target material. It is also shown that SIW propagation is strongly driven by the dielectric material near to the surface of the target in addition to the bulk material. The possible mechanisms driving these thickness dependent behaviors is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Characterizing Minimum Admissible Separation Distances in Heavy Duty Vehicle Platoons

Heavy duty (HD) vehicles platooning under highway operating conditions, have been projected to provide significant fuel economy (FE) gains based on aerodynamic drag reduction of the platooning vehicles. Realizing these benefits under real-world operating conditions have several challenges. This paper (the second as part of series) quantifies the minimum admissible separation distance between platooning vehicles in HD commercial vehicle (CV) applications. This distance must be set up such that no collision occurs with leading vehicles under all deceleration conditions. In this paper key interactions to characterize this distance are demonstrated. These include, road surface conditions, grade, inter-vehicle communication delays, air-brake lag time, vehicle speed, weight, and aerodynamic drag. It is seen that characterizing the vehicle and road dynamics will be critical in establishing required deceleration or stopping distances for each vehicle in a platoon. The results of the study also necessitate vehicle control systems that can dynamically adjust not only the separation distances but also the braking reference points based on road conditions. The narrative provides application decision personnel with a well-defined set of admissible separation distance impact factors to consider as part of their architecture selection process.

Sujan, Vivek↗
DOE OSTI2024

Effects of open circuit immersion and vertex potential on potentiodynamic polarization scans of metallic biomaterials

Abstract Electrodes made of commercially pure titanium (CP-Ti) and a CoCrMo alloy are immersed at an open circuit in a phosphate buffer saline electrolyte at room temperature for different durations prior to electrochemical analyses. Open circuit potential measurements, electrochemical impedance spectroscopy measurements, and cyclic potentiodynamic polarization (CPP) scans are used to assess the impact of the immersion time on derived property values. Stable passivation layers formed on both materials during immersion. The corrosion potentials determined from the anodic legs of CPP scans become more cathodic, and the corrosion currents decrease to lower values after longer immersion times. Measured currents indicate the layers formed on CP-Ti stabilize during forward anodic scans and persist to the vertex potential, whereas passivation breakdown occurs during anodic scans with CoCrMo with active corrosion at voltages up to the vertex potential. The characteristics of the return cathodic legs of CPP scans represent the surface conditions at the vertex potential: characteristic corrosion property values derived from the test responses represent passive surfaces on CP-Ti and leached surfaces on CoCrMo rather than intrinsic properties of those materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Laser spot welding of additive manufactured 304L stainless steel

Here, the goal of this work is to understand if an additively manufactured 304L stainless steel exhibits similar spot-welding behavior as wrought 304L stainless steel. Due to the many differences between an additively manufactured component and wrought product, it is important to determine how the material interacts with the laser and how it affects the weld bead morphology. In this paper, the laser coupling efficiency, weld size, and solidification of spot welds produced in wrought and additively manufactured 304L stainless steel were investigated. The coupling efficiency of wrought and additively manufactured 304L stainless steel of similar surface condition were approximately the same over a range of applied laser energies. Laser welding of the untreated (rougher) surface of additively manufactured 304L, however, showed improved coupling efficiency ranging between 3.3 and 100%. The rougher surface traps the incoming light and increases the coupling efficiency at lower laser energies, while at higher energy, the absorption efficiency is dominated by intrinsic absorption from the keyhole formation rather than surface roughness. The resulting spot weld microstructures differed from welds made in wrought 304L and additively manufactured 304L. Welds made in wrought 304L were fully austenitic containing what is suspected to be massive austenite, which suggests that these welds solidified as primary ferrite. Welds made in additively manufactured 304L were also fully austenitic and contained both cellular austenite and what is suspected to be massive austenite. These observations mean that welds made in additively manufactured 304L solidified as primary ferrite and primary austenite. The differences in weld microstructures made in wrought and AM 304L can be attributed to differences in the composition and solidification rate.

304L stainless steel↗
DOE OSTI2023

Selective laser melting of oxide dispersion strengthened MA956 alloy and its surface finishing by magnetic field assisted finishing

Selective laser melting (SLM) is a prominent metal additive manufacturing (AM) capable of processing a myriad of engineering materials with high precision and design freedom. However, similar to other AM processes, poor surface finishing has been an omnipresent problem in SLM technology. In this study, magnetic field assisted finishing (MAF) was used to finish SLM fabricated oxide dispersion strengthened (ODS) MA956, an iron-chromium-aluminum alloy. The effect of laser processing parameters on part density and surface roughness was first studied. Using a multi-objective optimization technique, the optimal parameters to obtain the highest density and lowest surface roughness were determined. Finally, MAF was applied to the parts built with the obtained optimal SLM parameters, but without significant improvement on the surfaces of as-printed samples. Hence, the surfaces of as-printed samples were post-processed (ground) to yield better initial surface conditions prior to MAF. The effect of initial roughness, iron particles size, and abrasive size on MAF performance was studied. Initial roughness had the most dominant effect followed by abrasive size. The underlying mechanism behind the dependency on initial roughness on final surface quality was analyzed by studying the change on the surface profiles with different starting initial roughness. The initial roughness required for MAF to be effective was determined. In conclusion, using the optimal processing conditions, MAF was applied to the post-processed samples to attain the final average surface roughness (R a ) as little as 0.36 μm starting from initial average roughness (R a ) of 1.53 μm.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of coated heat flux gauges for fast responding measurements

Thermal systems often exhibit transient behaviors that have important implications for the operation of the system and can be difficult to predict. For these reasons, experimental testing is often required to ensure system durability requirements are achieved. One important parameter governing the survivability of components in hot, high-stress environments is the heat flux into the part that dictates the temperature distribution for the component. However, sensors required to experimentally characterize heat fluxes in extreme environments must also be resilient. Here, this study presents the development of coated heat transfer gauges capable of robust, high-frequency measurements in turbine research facilities. The addition of a protective coating increases the durability of the gauge, but inherent of that coating is the attenuation of high-frequency temperature penetrations. As a result, this study first outlines the use of analytical solutions to define a gauge design for a specific frequency range and heat transfer, ensuring that subsurface signals can be rectified to surface conditions through inverse methods. Then, the fabrication of polyimide substrate sensors with a parylene-F coating is described. Micro surface heaters added to the custom sensors were used to determine important geometric and thermal properties necessary to calculate accurate surface heat flux. Ultimately, this work shows increased sensor robustness in a turbine test bed and experimentally validates that the frequency response of the fabricated sensors meet the design intent.

47 OTHER INSTRUMENTATION↗