Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Non-destructive evaluation of specific surface area of porous powder systems using experimental and virtual air permeametry

The correlation of flow-permeable surface area (FSSA) of porous initiator powder to its performance is well-established. More specifically, with age, such powders tend to coarsen (i.e., lose surface area), with an accompanying deterioration in performance. Commercially available permeametry apparatuses, such as that from Fisher Scientific or a more modern version from Micromeritics suffers from a few drawbacks, including: (1) the need to work with a fixed mass equivalent of 1 cm 3 of solid material; (2) the need to re-compact the material to monitor aging effects (which can introduce unwanted errors in the derived results); (3) a superfluous design that involves a reference plug, and for the older Fisher Scientific model, the need to eyeball water meniscus height that can lead to inaccuracies; (4) calibrated and tested only for samples packed in cylindrical geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Generalized synthesis of high surface area mesoporous metal titanates as efficient heterogeneous catalysts

A novel metal dissolution coupled with reverse micelle formation approach is used as a generalized synthesis method for a series of high surface area metal titanates where the metals used are Bi, Mg, V, Mn, Fe, Co, Ni, Cu, Zn, Mo, W, and Ce. This study reports the highest surface areas published so far. The homogeneous distributions of the metals and titanium are observed in SEM-EDX and TEM mapping. The synthesized materials were comprehensively characterized using PXRD, Raman, nitrogen adsorption isotherms, SEM; EDX, TEM, TEM mapping, TGA, and XPS. The green catalytic oxidation of aniline to nitrosobenzene occurs within 30 min at room temperature when mesoporous W/Ti binary metal oxide is used as the catalyst. The radical mediated catalytic reaction gives excellent yields and the catalyst is reusable up to 4 reaction cycles without losing significant activity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High surface area mesoporous tungsten oxide for fast, green oxidation of organosulfur compounds in crude oil

Mesoporous, multi-valent tungsten oxide with high surface area (209 m 2 /g) is synthesized via a novel metal dissolution coupled with reverse micelle formation approach. Mesoporous tungsten oxide with highest surface area reported is obtained by this method. The material is used as an excellent heterogeneous catalyst for the oxidation of organosulfur compounds present in crude oil. The complete oxidation of dibenzothiophene was observed with excellent yield (>99%) within 15 min at room temperature (20 °C). The catalyst is reusable up to 5 reaction cycles without losing significant activity. A green oxidant, H 2 O 2 is used and the reaction mechanism involves the activation of peroxo species by W 6+ . The oxidation activity decreases in the order of DBT > 4,6-DMDBT > 1-BT due to the changes in the electronic environment of sulfur and steric effects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mesoporous Crystalline Niobium Oxide with a High Surface Area: A Solid Acid Catalyst for Alkyne Hydration

A mesoporous crystalline niobium oxide with tunable pore sizes was synthesized via the sol–gel-based inverse micelle method. The material shows a surface area of 127 m 2 /g, which is the highest surface area reported so far for crystalline niobium oxide synthesized by soft template methods. The material also has a monomodal pore size distribution with an average pore diameter of 5.6 nm. A comprehensive characterization of niobium oxide was performed using powder X-ray diffraction, Brunauer–Emmett–Teller, thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, UV–vis, and X-ray photoelectron spectroscopy. The material acts as an environmentally friendly, solid acid catalyst toward hydration of alkynes under with excellent catalytic activity (99% conversion, 99% selectivity, and 4.39 h –1 TOF). Brønsted acid sites present in the catalyst were found to be responsible for the high catalytic activity. Lastly, the catalyst was reusable up to five cycles without a significant loss of the activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Impact of Mineral Reactive Surface Area on Forecasting Geological Carbon Sequestration in a CO2-EOR Field

Mineral reactive surface area (RSA) is one of the key factors that control mineral reactions, as it describes how much mineral is accessible and can participate in reactions. This work aims to evaluate the impact of mineral RSA on numerical simulations for CO2 storage at depleted oil fields. The Farnsworth Unit (FWU) in northern Texas was chosen as a case study. A simplified model was used to screen representative cases from 87 RSA combinations to reduce the computational cost. Three selected cases with low, mid, and high RSA values were used for the FWU model. Results suggest that the impact of RSA values on CO2 mineral trapping is more complex than it is on individual reactions. While the low RSA case predicted negligible porosity change and an insignificant amount of CO2 mineral trapping for the FWU model, the mid and high RSA cases forecasted up to 1.19% and 5.04% of porosity reduction due to mineral reactions, and 2.46% and 9.44% of total CO2 trapped in minerals by the end of the 600-year simulation, respectively. The presence of hydrocarbons affects geochemical reactions and can lead to net CO2 mineral trapping, whereas mineral dissolution is forecasted when hydrocarbons are removed from the system.

58 GEOSCIENCES↗
DOE OSTI2020

Correlating Oxidation State and Surface Area to Activity from Operando Studies of Copper CO Electroreduction Catalysts in a Gas-Fed Device

Copyright © 2020 American Chemical Society. The rational design of high-performance electrocatalysts requires a detailed understanding of dynamic changes in catalyst properties, including oxidation states, surface area, and morphology under realistic working conditions. Oxide-derived Cu catalysts exhibit a remarkable selectivity toward multicarbon products for the electrochemical CO reduction reaction (CORR), but the exact role of the oxide remains elusive for explaining the performance enhancements. Here, we used operando X-ray absorption spectroscopy (XAS) coupled with simultaneous measurements of the catalyst activity and selectivity by gas chromatography (GC) to study the relationship between oxidation states of Cu-based catalysts and the activity for ethylene (C2H4) production in a CO gas-fed cell. By utilizing a custom-built XAS cell, oxidation states of Cu catalysts can be probed in device-relevant settings and under high current densities (>80 mA cm-2) for the CORR. By employing an electrochemical oxidation process, we found that the Cu oxidation states and specific ion species do not correlate with C2H4 production. The difference in the CORR activity is also investigated in relation to electrochemical surface area (ECSA) changes. While the hydrogen evolution reaction (HER) activity is positively correlated to the ECSA changes, the increased C2H4 activity is not proportional to the ECSA. Ex situ characterization from microscopic techniques suggests that the changes in the C2H4 activity and selectivity may arise from a morphological transformation that evolves into a more active structure. These comprehensive results give rise to the development of a cell regeneration method that can restore the performance of the Cu catalyst without cell disassembly. Our study establishes a basis for the rational design of highly active electrocatalysts for broad-range reactions in a gas-fed device.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Estimation of Sea Spray Aerosol Surface Area Over the Southern Ocean Using Scattering Measurements

This study focuses on methods to estimate dry marine aerosol surface area (SA) from bulk optical measurements. Aerosol SA is used in many models' ice nucleating particle (INP) parameterizations, as well as influencing particle light scattering, hygroscopic growth, and reactivity, but direct observations are scarce in the Southern Ocean (SO). Two campaigns jointly conducted in austral summer 2018 provided co-located measurements of aerosol SA from particle size distributions and lidar to evaluate SA estimation methods in this region. Mie theory calculations based on measured size distributions were used to test a proposed approximation for dry aerosol SA, which relies on estimating effective scattering efficiency (Q) as a function of Ångström exponent (å). For distributions with dry å < 1, Q = 2 was found to be a good approximation within ±50%, but for distributions with dry å > 1, an assumption of Q = 3 as in some prior studies underestimates dry aerosol SA by a factor of 2 or more. We propose a new relationship between dry å and Q, which can be used for –0.2 < å < 2, and suggest å = 0.8 as the cutoff between primary and secondary marine aerosol-dominated distributions. Application of a published methodology to retrieve dry marine aerosol SA from lidar extinction profiles overestimated aerosol SA by a factor of 3–5 during these campaigns. Using Microtops aerosol optical thickness measurements, we derive alternative lidar conversion parameters from our observations, applicable to marine aerosol over the SO.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Experimental Characterization of High-Surface Area Thermal Energy Storage

There is growing interest in energy storage technologies due to the expansion of renewable energy sources that are inherently intermittent and the increasing frequency of extreme weather events that disturb the power grid. Power consumption in buildings makes up approximately 76% of all electricity usage on the grid and is primarily used for thermal applications such as space conditioning, hot water, and cooking. This makes thermal energy storage (TES) an ideal solution for many of these applications. Many TES technologies rely on latent energy storage, which utilizes the melting/solidification of phase change materials (PCM) to store energy. Typically, TES designs suffer from low power density due to their low inherent thermal conductivity. This limitation makes the deployment of TES in active applications difficult as the ease of access to energy is essential for effective use. Common routes for improving power density include high thermal conductivity additives or extended features such as fins that increase cost. This study presents an alternative approach to improving performance through increasing the overall surface area to volume ratio of the device, to increase the available area for convection to occur between the working fluid and PCM. In the study a commercial PCM was selected with a transition temperature ideal for space heating applications. The heat exchanger design utilizes a unique application of triply periodic minimal surfaces (TPMS) for macro-encapsulation of the PCM. The use of TPMS for heat exchangers has been growing in interest due to their high-surface area to volume ratios, which were previously unmanufacturable until the development of additive manufacturing. A modular system was designed and manufactured with a stereolithography resin printing system that is then backfilled with PCM. An experiment test set-up is designed to test the charge and discharge performance of the thermal storage using a conditioned air stream. The pressure drop of the design is tested across a variety of flow rates. When compared to existing experimental data within literature, there is excellent agreement based on the Reynolds number at similar hydraulic diameters. Several inlet temperatures are tested at consistent temperature differences from the phase change temperature for both charging and discharging. Additionally, the volumetric flow rate is varied for each temperature set point. It was found that increasing flow rate had diminishing returns in reducing the overall charge time of the TES. The temperature delta from the melting temperature was the primary contributor to the change in average heat flux with limited variation in average heat transfer rate between charging and discharging at similar inlet temperatures and flow rates. The TPMS heat exchanger design has a high air-side pressure drop but it provides high heat transfer rates. This helps maintain a high outlet temperature during discharge, which is important to thermal comfort applications. The design, manufacturing, and experimental characterization of the TES device will be presented as part of this study.

25 ENERGY STORAGE↗
DOE OSTI2022

Measurement of isosteric heat of gas adsorption and Brunauer–Emmett–Teller (BET) surface area using a quartz crystal microbalance

The study of gas adsorption on a solid surface evaluates the affinity between sorbate gas and sorbent substrate and factors that contribute to this. This report presents a test platform for adsorption experiments of various gases on various solid surfaces. Controlled environmental conditions enable investigations in materials surface science and increase the consistency among adsorption data. The system utilizes a quartz crystal microbalance to perform gravimetric analysis of deposition and adsorption, enabling investigation of the interaction of gaseous molecules with solid surfaces. In this study, a quartz crystal microbalance as gas adsorption detector was integrated with an environmental chamber to create a versatile tool for gas adsorption experiments on thin films. Experimental operation of this apparatus was demonstrated via acquisition of the adsorption isotherms of cyclohexane vapor on a gold surface at 55 and 70 °C. The result indicated International Union of Pure and Applied Chemistry Type II adsorption. Consequentially, application of the Brunauer–Emmett–Teller model to the isotherm data subject to predefined criteria for linear region selection yielded a surface area of the sorbent of 0.53 cm2 at 55 °C. From the monolayer region of the isotherms, the isosteric heat of adsorption of the cyclohexane vapor on gold was calculated to be 37 kJ mol-1.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

High surface area magnetic double perovskite La 2 AlFeO 6 as an efficient and stable photo-Fenton catalyst under a wide pH range

Photo-Fenton process is an efficient way to treat the organic pollutants in wastewater. However, the efficiency is limited by serious leaching of iron ion, separation of spent catalyst from reaction system for facile recycling, low (pH<4) reaction environment. Herein, we report a preparation of a novel magnetic double perovskite photocatalyst La2AlFeO6, and refractory organic pollutants like phenol, etc. were used as probes to test the efficiency of catalyst. The results showed that the catalytic material retained high surface area and high ratio of Fe 3+ on its surface, and the generated ·OH, ·O 2 - and 1 O 2 lead to a highly photocatalytic efficiency even at neutral pH condition. In addition, the as prepared double perovskite photocatalyst La 2 AlFeO 6 also exhibits excellent stable and magnetic properties. There is no iron ion leaching detected during the courses of the reaction. Furthermore, the spent catalyst can be separated by magnetic field easily, and thus can be reused after simple air drying without any further treatment or calcination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

On the evolution of scalar iso-surface area density in a turbulent mixing layer

In this paper, the transport equation for scalar iso-surface area density (Σ) in a turbulent, temporally developing mixing layer is examined. Exploring the spatial and temporal evolution of the terms in the Σ transport equation is vital to improving our understanding of turbulent flows characterized by distinct interfaces, e.g. the flame surface or the turbulent/non-turbulent interface. Previous work reported by the authors identified that Σ exhibits self-similar behaviour consistent with the development of the temporal mixing layer. Accordingly, each of the terms in the Σ transport equation is found to behave in a self-similar manner, though there are notable differences in the self-similar behaviours for each term. Based on the results presented herein, it is suggested that the rate of change of Σ (∂Σ/∂t) and the advection term scale with hλ Φ /ΔU, where h is the width of the mixing layer, λ Φ is the scalar Taylor length scale and ΔU is the velocity difference. The production and destruction terms are found to scale with an additional factor (ReSc) 1/2 . In contrast, the molecular diffusion term is found to scale with a factor (ReSc) –1/2 compared to ∂Σ/∂t. Importantly, it is found that the difference between the production and destruction terms, or net surface ‘stretch’, scales with the same factor as ∂Σ/∂t and the advection term, which may have a significant impact on how the evolution of Σ is understood and modelled in turbulent flows.

42 ENGINEERING↗
DOE OSTI2024

Enzymatic depolymerization of polyester: Foaming as a pretreatment to increase specific surface area

Abstract Poly(ethylene terephthalate) (PET) is widely used for its high strength‐to‐weight ratio, gas barrier properties, and chemical resistance. The growing PET use highlights the demand for a better recycling system. Enzymatic recycling, alongside mechanical and chemical methods, is eco‐friendly and yields properties similar to virgin PET. Substrate properties ( T g , crystallinity, and specific surface area [SSA]) and enzyme stability significantly impact conversion efficiency. Higher SSA and lower crystallinity tend to yield improved depolymerization when employing leaf compost‐cutinase (LCC‐ICCG) enzymes. This study explored melt extrusion and foaming as pretreatment techniques to modify PET structural properties, using a low‐cost chemical foaming agent (CFA). The monomer conversion rate and efficiency during depolymerization were measured and related to the processing, extrudate micro‐ and meso‐structure, and polyester type. Pretreated PET substrates showed reduced T g , crystallinity, density, and enhanced SSA, resulting in a 90% mass loss for foamed RPET and VPET substrates within 2 days. In contrast, PET with ~30% of cyclohexanedimethanol comonomer exhibited a nearly 50% lower depolymerization rate, with zero BHET production. It indicates that the combination of low crystallinity, low T g , and high SSA leads to improved monomer conversion. These findings emphasize the significance of amorphization and foaming in enhancing PET enzymatic depolymerization.

42 ENGINEERING↗
DOE OSTI2021

Tropospheric and stratospheric wildfire smoke profiling with lidar: mass, surface area, CCN, and INP retrieval

We present retrievals of tropospheric and stratospheric height profiles of particle mass, volume, surface area, and number concentrations in the case of wildfire smoke layers as well as estimates of smoke-related cloud condensation nuclei (CCN) and ice-nucleating particle (INP) concentrations from backscatter lidar measurements on the ground and in space. Conversion factors used to convert the optical measurements into microphysical properties play a central role in the data analysis, in addition to estimates of the smoke extinction-to-backscatter ratios required to obtain smoke extinction coefficients. The set of needed conversion parameters for wildfire smoke is derived from AERONET observations of major smoke events, e.g., in western Canada in August 2017, California in September 2020, and southeastern Australia in January–February 2020 as well as from AERONET long-term observations of smoke in the Amazon region, southern Africa, and Southeast Asia. The new smoke analysis scheme is applied to CALIPSO observations of tropospheric smoke plumes over the United States in September 2020 and to ground-based lidar observation in Punta Arenas, in southern Chile, in aged Australian smoke layers in the stratosphere in January 2020. These case studies show the potential of spaceborne and ground-based lidars to document large-scale and long-lasting wildfire smoke events in detail and thus to provide valuable information for climate, cloud, and air chemistry modeling efforts performed to investigate the role of wildfire smoke in the atmospheric system.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Oxidative Self-Assembly of Au/Ag/Pt Alloy Nanoparticles into High-Surface Area, Mesoporous, and Conductive Aerogels for Methanol Electro-oxidation

The ability to assemble nanoparticles (NPs) into functional nanostructures is critical for the advancement of nanoscience. However, common assembling techniques utilize organic ligands or biomolecules, which are detrimental for charge transport and interparticle coupling, which impede the efficient integration of low-dimensional properties. Herein, we report a methodology for the self-supported assembly of ultra-small (3-6 nm) Au/Ag/Pt alloy NPs into large, free-standing alloy superstructures (aerogels) that exhibit direct NP connectivity, high surface area (125 ± 0.43 to142 ± 0.93 m 2 /g) and mesoporosity (21.6 ± 2.2 nm), and superior electrocatalytic activity for methanol oxidation reaction (MOR). Precursor Au/Ag/Pt alloy NPs and hydrogels were synthesized via stepwise galvanic replacement reaction (GRR) of the glutathione (GSH)-coated Ag NPs, followed by oxidative removal of the surfactant ligands. The composition of alloy aerogels was tuned by varying the oxidant/GSH molar ratio, which governs the extent of Ag dealloying with in-situ generated HNO 3 and increases the exposure of Au and Pt on the aerogel surface. The alloy aerogels exhibit superior MOR mass activity, which is 21.4 and 2.5 times higher than those of the precursor NPs and commercial Pt (40 wt.%)/C electrocatalysts, respectively. The MOR surface-specific activity (MOR-SSA) of the aerogels was improved by >17% when the Pt content was increased from 22.4% to 31.2%. The aerogels exhibit improved electronic conductivity, enhanced tolerance for carbonaceous byproducts, and maintained ~94% of the initial MOR activity at -0.3 V for 24 h in an alkaline medium. In conclusion, the interconnected porous superstructure of the aerogel provides a facile conduit for molecules to reach the pristine active surface whereas the presence of oxophilic Au promotes the dissociative adsorption of methanol, enabling the Au/Ag/Pt alloy aerogel a high efficiency, durable electrocatalyst for next generation of energy conversion studies.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Relative-Humidity Dependence of Electrochemically Active Surface Area in Porous Carbon Catalyst Layers

Polymer-electrolyte fuel cells (PEFCs) utilize porous catalyst layers (CLs) formed of carbon supports on which Pt particles are deposited and ionomer films are distributed. Carbon supports themselves have varying degrees of porosity, where high-surface-area carbon (HSC) supports possess nanometer-sized interior pores that are suitable for Pt nanoparticle deposition but prevent deleterious ionomer penetration. However, this requires protons to transport through water pathways inside the pores. To understand the generation of such pathways, we examine the various mechanisms of water uptake by PEFC CLs, and the subsequent impact of water uptake on Pt utilization through developing a multiphysics model of the water wetting phenomena as a function of relative humidity. The model details water uptake via ionomer absorption, capillary condensation in the hydrophilic pores, and surface adsorption using molecular potential that account for various water and surface dipole interactions. The results quantify how mesoporous carbons with highly hydrophilic pores increase Pt utilization through the development of wetted layers, which at the same time enable optimized gas-transport pathways. It also demonstrates the impact of pore-size distribution (PSD) and physical and chemical parameters on the water uptake phenomena, allowing for future CL particle and structure optimization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗