Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “superior rate performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Polycarbonate‐Based Solid‐Polymer Electrolytes for Solid‐State Sodium Batteries

Solid-polymer electrolytes comprised of polypropylene carbonate (PPC) and varied sodium bis(fluorosulfonyl)imide (NaFSI) salt concentrations are investigated for implementation as a conductive solid polymer electrolyte into solid-state cathode composites utilizing a sodium-layered oxide active material. The ionic conductivity generally increases with NaFSI salt content, reaching ≈1 mS cm −1 at 80 °C at the highest salt concentration (PPC:NaFSI = 0.5:1). Through an all-in-one slurry casting method, Na 2/3 Ni 1/3 Mn 2/3 O 2 cathode composites are fabricated in which the dispersed PPC electrolyte acts as the primary binder. Enabled by a bilayer polymer electrolyte system, cycling performance with the PPC cathode electrolyte is optimized with respect to salt concentration and anode material. The best cyclability is achieved with a moderate salt concentration electrolyte (PPC:NaFSI = 5:1), showcasing an initial capacity of 83 mA h g −1 with a remarkable 80% capacity retention after 150 cycles at C/5 rate and 60 °C. The superior performance of the lower salt concentration electrolyte is attributed to better electrochemical stability, as confirmed by linear sweep voltammetry and online electrochemical mass spectrometry measurements. In conclusion, these results underscore the potential of carbonate-based polymer electrolytes and the importance of balancing electrolyte conductivity and stability in cell design.

25 ENERGY STORAGE↗
DOE OSTI2025

Transforming CO 2 to Porous Carbon as a High-Performing Sodium-Ion Battery Anode via Electrochemical Reduction in Molten Carbonates

The prevalence of sodium over lithium prompts exploration of sodium-ion batteries (SIBs) as a viable alternative to lithium-ion batteries (LIBs). Hard carbon has emerged as a promising anode material for SIBs, yet its synthesis poses sustainability challenges and emits pollutants. Here, in this study, we introduce CO 2 -derived porous carbon (graphitic and amorphous) as an anode for SIBs via electrochemical reduction of CO 2 in a molten eutectic carbonate salt at a lower temperature that yields materials with controlled microstructure, morphology, and porosity conducive to energy storage. Our CO 2 -derived carbon demonstrates remarkable specific capacity, superior rate capability, and stable cycling performance as a SIB anode. This innovative strategy harnesses waste CO 2 toward advancing SIB energy technology.

CO2-derived carbon↗
DOE OSTI2025

Biobased Poly(dodecylene Furanoate) with Inherent Advantages in Performance and Circularity

Biobased polymers are gaining traction toward more sustainable flexible-film packaging, yet overcoming trade-offs between their performance properties and end-of-life (EoL) options still remains a challenge. Here, it is shown that biobased poly(dodecylene 2,5-furanoate) (PDDF), synthesized via both step-growth polycondensation and chain-growth ring-opening polymerization methods, exhibits advantages not only in gas barrier properties but also in EoL options due to its biodegradability and closed-loop chemical circularity. Specifically, PDDF displays significantly lower oxygen and carbon dioxide permeability than commercial poly(butylene adipate-co-terephthalate) (PBAT) and linear low-density polyethylene , alongside a markedly higher modulus (by ≈3 ×) and reduced water vapor transmission rate compared to PBAT. This superior performance is attributed to the inherently rigid, polar, H-bonding furan rings that enhance chain interaction, packing and crystallinity and thus reduce free volume impeding gas diffusion, while the long hydrophobic dodecylene segments inhibit water permeation. Furthermore, PDDF can be recycled back to its cyclic monomer by base-catalyzed depolymerization or diester and diol monomers by simple methanolysis. These superior barrier properties, coupled with biodegradation and closed-loop circularity, highlight the potential of the biobased PDDF as a more sustainable alternative for packaging.

Poly(dodecylene 2,5-furanoate) (PDDF)↗
DOE OSTI2024

On the effect of strain rate during the cyclic compressive loading of liquid crystal elastomers and their 3D printed lattices

Nematic liquid crystal elastomers (LCEs) are a unique class of network polymers with the potential for enhanced mechanical energy absorption and dissipation capacity over conventional network polymers because they exhibit both conventional viscoelastic behavior and soft-elastic behavior (nematic director changes under shear loading). This additional inelastic mechanism makes them appealing as candidate damping materials in a variety of applications from vibration to impact. The lattice structures made from the LCEs provide further mechanical energy absorption and dissipation capacity associated with packing out the porosity under compressive loading. Understanding the extent of mechanical energy absorption, which is the work per unit mass (or volume) absorbed during loading, versus dissipation, which is the work per unit mass (or volume) dissipated during a loading cycle, requires measurement of both loading and unloading response. Here, in this study, a bench-top linear actuator was employed to characterize the loading-unloading compressive response of polydomain and monodomain LCE polymers and polydomain LCE lattice structures with two different porosities (nominally, 62% and 85%) at both low and intermediate strain rates at room temperature. As a reference material, a bisphenol-A (BPA) polymer with a similar glass transition temperature (9 °C) as the nematic LCE (4 °C) was also characterized at the same conditions for comparing to the LCE polymers. Based on the loading-unloading stress-strain curves, the energy absorption and dissipation for each material at different strain rates (0.001, 0.1, 1, 10 and 90 s -1 ) were calculated with considerations of maximum stress and material mass/density. The strain-rate effect on the mechanical response and energy absorption and dissipation behaviors was determined. The energy dissipation ratio was also calculated from the resultant loading and unloading stress-strain curves. All five materials showed significant but different strain rate effects on energy dissipation ratio. The solid LCE and BPA materials showed greater energy dissipation capabilities at both low (0.001 s -1 ) and high (above 1 s -1 ) strain rates, but not at the strain rates in between. The polydomain LCE lattice structure showed superior energy dissipation performance compared with the solid polymers especially at high strain rates.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Extended Interfacial Stability through Simple Acid Rinsing in a Li-Rich Oxide Cathode Material

Layered Li-rich Ni, Mn, Co (NMC) oxide cathodes in Li-ion batteries provide high specific capacities (>250 mAh/g) via O-redox at high voltages. However, associated high-voltage interfacial degradation processes require strategies for effective electrode surface passivation. Here, we show that an acidic surface treatment of a Li-rich NMC layered oxide cathode material leads to a substantial suppression of CO 2 and O 2 evolution, ~90% and ~100% respectively, during the first charge up to 4.8 V vs. Li +/0 . CO 2 suppression is related to Li 2 CO 3 removal as well as effective surface passivation against electrolyte degradation. This treatment does not result in any loss of discharge capacity and provides superior long-term cycling and rate performance compared to as-received, untreated materials. We also quantify the extent of lattice oxygen participation in charge compensation (“O-redox”) during Li + removal by a novel ex-situ acid titration. Our results indicate that the peroxo-like species resulting from O-redox originate on the surface at least 300 mV earlier than the activation plateau region around 4.5 V. X-ray photoelectron spectra and Mn -L X-ray absorption spectra of the cathode powders reveal a Li + deficiency and a partial reduction of Mn ions on the surface of the acid-treated material. More interestingly, although the irreversible oxygen evolution is greatly suppressed through the surface treatment, our O K-edge resonant inelastic X-ray scattering shows the lattice O-redox behavior largely sustained. The acidic treatment, therefore, only optimizes the surface of the Li-rich material and almost eliminates the irreversible gas evolution, leading to improved cycling and rate performance. This work therefore presents a simple yet effective approach to passivate cathode surfaces against interfacial instabilities during high-voltage battery operation.

25 ENERGY STORAGE↗
DOE OSTI2022

Superior Daily and Sub-Daily Precipitation Statistics for Intense and Long-Lived Storms in Global Storm-Resolving Models

Here, daily and sub-daily precipitation statistics are investigated from three global model ensembles: (a) global storm-resolving models (GSRMs) with typical horizontal resolutions of ~4 km, (b) “high”-resolution global models with typical resolutions of ~50 km and (c) “standard”-resolution global models with typical resolutions of ~100 km. Compared to two satellite rainfall datasets, GSRMs convincingly exhibit superior performance for statistics of heavier rain rate events including their diurnal cycle, spatial propagation and the amount contributed by intense precipitation, but not for statistics of weaker or shorter duration precipitation. Both high- and standard-resolution models fail to simulate the correct phase and amplitude of diurnal cycle of precipitation and the propagating convection in the Central US, but high-resolution models show relative improvement in the distribution of precipitation frequency and amount, especially for intense precipitation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Gel composite electrolyte – an effective way to utilize ceramic fillers in lithium batteries

Achieving synergy between ion-conducting polymers and ceramics in a composite electrolyte has been proven to be difficult as the complicated ceramic/polymer interface presents challenges to understand and control. In this work, we report a strategy to utilize discrete ceramic fillers to form a gel composite electrolyte with enhanced transport properties for lithium metal batteries. The matrix of the composite membrane is crosslinked poly(ethylene oxide) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI). The membrane is plasticized with tetraethylene glycol dimethyl ether (TEGDME). The incorporation of doped-lithium aluminum titanium phosphate particles (LICGC™) into the membrane greatly improves the membrane's cycling characteristics against the lithium electrode, exhibiting lower interfacial impedance, lower overpotential and higher rate capability. The underpinnings of the superior performance of the gel composite electrolyte are discussed in depth. LICGC™ can immobilize the TFSI - anions in the polymer matrix and simultaneously promote Li+ transport by increasing the plasticizer to Li + ratio. Further, the transport enhancement is achieved without sacrificing mechanical properties. The composite membrane shows significantly improved handleability and processability. This work sheds light on the design strategy for a safe electrolyte towards stable Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Reduced metal nanocatalysts for selective electrochemical hydrogenation of biomass-derived 5-(hydroxymethyl)furfural to 2,5-bis(hydroxymethyl)furan in ambient conditions

Selective electrochemical hydrogenation (ECH) of biomass-derived unsaturated organic molecules has enormous potential for sustainable chemical production. However, an efficient catalyst is essential to perform an ECH reaction consisting of superior product selectivity and a higher conversion rate. Here, we examined the ECH performance of reduced metal nanostructures, i.e., reduced Ag (rAg) and reduced copper (rCu) prepared via electrochemical or thermal oxidation and electrochemical reduction process, respectively. Surface morphological analysis suggests the formation of nanocoral and entangled nanowire structure formation for rAg and rCu catalysts. rCu exhibits a slight enhancement in ECH reaction performance in comparison to the pristine Cu. However, the rAg exhibits more than two times higher ECH performance without compromising the selectivity for 5-(HydroxyMethyl) Furfural (HMF) to 2,5-bis(HydroxyMethyl)-Furan (BHMF) formation in comparison to the Ag film. Moreover, a similar ECH current density was recorded at a reduced working potential of 220 mV for rAg. This high performance of rAg is attributed to the formation of new catalytically active sites during the Ag oxidation and reduction processes. This study demonstrates that rAg can potentially be used for the ECH process with minimum energy consumption and a higher production rate.

2,5- bis(hydroxymethyl)furan (BHMF)↗
DOE OSTI2022

Multifunctional transitional metal-based phosphide nanoparticles towards improved polysulfide confinement and redox kinetics for highly stable lithium-sulfur batteries

The shuttle effect and the sluggish redox kinetics of lithium polysulfides (LiPSs) are the major issues impeding the practical applications of lithium-sulfur batteries (LSBs). Herein, a highly-efficient Ni 2 P electrocatalyst supported on N, P co-doped graphene (Ni 2 P@NPG) is developed via a simple “recrystallization-self-assembly” method to address the above issues. Here, the ultrafine Ni 2 P nanoparticles ensure abundant adsorption-diffusion-conversion interfaces for accelerating LiPSs transformation and Li 2 S deposition, which extremely decreases the accumulation of LiPSs in the electrolyte and therefore prevents the migration of LiPSs. Their superior catalytic performance is demonstrated by reduced Gibbs free energy changes of rate-limiting step based on the systematic theoretical calculations and the reduced shuttle effect is tested by the three-dimensional reconstructions of Raman depth profiles. Benefiting from these synergistic effects, the LSBs with Ni 2 P@NPG modified separators present a superior cycling performance with an average capacity decay rate of 0.048 % per cycle at 1C around the 400 cycles and a high-rate capacity of 731 mAh/g at 2C. Even with a high-sulfur loading of 3.53 mg cm –2 , the cell can still contain a reversible capacity of 809 mAh/g at 0.2C with a remarkable columbic efficiency of 98.4 %.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

3D Printed Nanoporous Separators Based on Polymerization-Induced Phase Separation for Fast-Charging, High Cycling Stability Li-Ion Batteries

Fast charging and stable lithium-ion batteries (LIBs) require prompt Li ion transport between electrodes. 3D porous separators can potentially improve ion transport at both the microscale and macroscale levels. Additive manufacturing (AM) is an ideal tool to produce and study 3D porous separators of LIBs, although little work has been reported in this area. Here, we demonstrate porous structural control in layer-by-layer printed hexanediol diacrylate (HDDA) separators using a projection micro stereolithography (PμSL) AM technology and present their corresponding battery performance in lithium nickel manganese cobalt oxide (NMC)/graphite full cells. The composition of photocurable resin determines the porous morphology (e.g., bicontinuous and droplet-like), while the settings of printing layer thickness and number of exposures can be used to adjust the porosity (e.g., from 27% to 63%). Optimal resin and print conditions are determined, and the resulting separator exhibits superior Li ion conductivity and therefore higher rate performance and longer cycling life. Compared with a Celgard 2325 separator, the optimized porous HDDA separator increases the 10C-rate capacity by 34% and decreases the capacity degradation rate at the 1C-rate by 4.9%. In conclusion, this work paves the way for future AM of 3D separators for high-energy, high-power, and long-cycling-life LIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Aqueous Ni-rich-cathode dispersions processed with phosphoric acid for lithium-ion batteries with ultra-thick electrodes

Lithium-ion battery (LIB) production can benefit both economically and environmentally from aqueous processing. Although these electrodes have the potential to surpass electrodes conventionally processed with N -methyl-2-pyrrolidone (NMP) in terms of performance, significant issues still exist with respect to ultra-thick cathodes ($\gg$4 mAh/cm 2 areal capacities). A major concern for these types of electrodes with high-nickel active material stems from lithium leaching from active material, which drives the pH of the dispersion in excess of 12 and subsequently corrodes the current collector interface. As this corrosion reaction proceeds, hydrogen generation at the interface creates bubbles which cause severe cracking in the dried electrode surface. When areal loadings are increased, this effect becomes more pronounced and is detrimental to both mechanical and electrochemical properties of these electrodes. In this work, a technique for mitigating corrosion at the current collector by adjusting the pH of the dispersion with the addition of phosphoric acid is investigated. Phosphoric acid was added in 0.5 wt% increments between 0.0 and 1.5 wt%, and effects on rheology, adhesion, corrosion, and electrochemical performance were investigated. A technique is reported for producing aqueous processed cathodes with areal loadings of 6–8 mAh/cm 2 with reduced surface cracking and superior high-rate discharge capacity (i.e. high-power performance) for this class of cathode loadings.

25 ENERGY STORAGE↗
DOE OSTI2024

Identification of Distorted Gamma-Ray Signature Patterns Using Digital Filtering and Auto-Associative Memory Implemented with a Hopfield Neural Network

The detection and identification of radioactive sources in search applications involve analyzing passive gamma-ray emissions from high-level radioactive materials. This process uses a mobile detector-spectrometer in a complex field test environment. Recently, the use of artificial intelligence for gamma-ray spectrum analysis has shown promising results. However, challenges persist in identifying isotopic signatures from spectral measurements that may be distorted due to source shielding, random variations in natural radioactive background, or insufficient measurement time to obtain clear spectral lines. Here, this paper presents a novel intelligent signature recognition method that combines digital filtering techniques with an artificial Hopfield Neural Network (HNN). The HNN leverages auto-associative memory to store training sample patterns and match them with incoming gamma spectra from distorted sources. It restores the testing sources’ measurements by finding the closest matching signature patterns in the spectral library. Before HNN recognition, the measured spectrum undergoes preprocessing with a digital image filter to reduce fluctuations. Performance of the proposed method is evaluated using a set of gamma-ray spectra measured with a sodium iodide detector. The data collected include measurements from six pure samples: 241 Am, 60 Co, 137 Cs, 192 Ir, 239 Pu, and 235 U, which are used for training and validation (i.e. six cases). Additionally, the data set contains 24 distorted synthesized sources with various fluctuating backgrounds. Test results demonstrate the potential of the proposed method to accurately recognize the correct isotope with high precision, achieving an accuracy rate exceeding 85%. Furthermore, the proposed method exhibits superior performance compared to the conventional multiple regression fitting and simple feedforward neural network methods.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Quantifying leaf symptoms of sorghum charcoal rot in images of field‐grown plants using deep neural networks

Abstract Charcoal rot of sorghum (CRS) is a significant disease affecting sorghum crops, with limited genetic resistance available. The causative agent, Macrophomina phaseolina (Tassi) Goid, is a highly destructive fungal pathogen that targets over 500 plant species globally, including essential staple crops. Utilizing field image data for precise detection and quantification of CRS could greatly assist in the prompt identification and management of affected fields and thereby reduce yield losses. The objective of this work was to implement various machine learning algorithms to evaluate their ability to accurately detect and quantify CRS in red‐green‐blue images of sorghum plants exhibiting symptoms of infection. EfficientNet‐B3 and a fully convolutional network emerged as the top‐performing models for image classification and segmentation tasks, respectively. Among the classification models evaluated, EfficientNet‐B3 demonstrated superior performance, achieving an accuracy of 86.97%, a recall rate of 0.71, and an F1 score of 0.73. Of the segmentation models tested, FCN proved to be the most effective, exhibiting a validation accuracy of 97.76%, a recall rate of 0.68, and an F1 score of 0.66. As the size of the image patches increased, both models’ validation scores increased linearly, and their inference time decreased exponentially. This trend could be attributed to larger patches containing more information, improving model performance, and fewer patches reducing the computational load, thus decreasing inference time. The models, in addition to being immediately useful for breeders and growers of sorghum, advance the domain of automated plant phenotyping and may serve as a foundation for drone‐based or other automated field phenotyping efforts. Additionally, the models presented herein can be accessed through a web‐based application where users can easily analyze their own images.

Gonzalez, Emmanuel M.↗
DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Pinned Electrode/Electrolyte Interphase and Its Formation Origin for Sulfurized Polyacrylonitrile Cathode in Stable Lithium Batteries

Sulfurized polyacrylonitrile (SPAN) represents one of the most promising directions for high-energy-density lithium (Li)-sulfur batteries. However, the practical application of Li||SPAN is currently limited by the insufficient chemical/electrochemical stability of electrode/electrolyte interphase (EEI). Here, a pinned EEI layer is designed for stabilizing a SPAN cathode by regulating the EEI formation mechanism in an advanced LiFSI/ether/fluorinated-ether electrolyte. Computational simulations and experimental investigations reveal that, benefiting from the nonsolvating nature, the fluorinated-ether can not only act as a protective shield to prevent the Li polysulfides dissolution but also, more importantly, endow a diffusion-controlled EEI formation process. It promotes the formation of a uniform, protective, and conductive EEI layer pinning into SPAN surface region, enabling the high loading Li||SPAN batteries with superior cycling stability, wide temperature performance, and high-rate capability. Finally, this design strategy opens an avenue for exploring advanced electrolytes for Li||SPAN batteries and guides the interface design for broad types of battery systems.

25 ENERGY STORAGE↗
DOE OSTI2020

Ptychographic phase retrieval by proximal algorithms

We derive a set of ptychography phase-retrieval iterative engines based on proximal algorithms originally developed in convex optimization theory, and discuss their connections with existing ones. The use of proximal operator creates a simple frame work that allows us to incorporate the effect of noise from a maximum-likelihood (ML) principle. We focus on three particular algorithms, namely proximal minimization, alternating direction method of multiplier and accelerated proximal gradient (APG). We benchmark their performance with numerical simulations, and discuss their optimal conditions for convergence and accuracy. An experimental dataset is used to demonstrate their effectiveness as well, in which case an array of cubic Au nanoparticles with a size of 50 nm is imaged. We show that with the presence of Poisson noise, a dataset with photon counts up to 10 4 at one detector pixel already requires ML-based methods to achieve a stable convergence. Among the three algorithms derived in this work, APG method is reported first time for its application in ptychographic reconstruction and shows superior performance in terms of both accuracy and convergence rate with a noisy dataset.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Automated Waterbox Inspection for Nuclear Power Plants Using Computer Vision - Based Change Detection

Nuclear power plant waterboxes require regular inspection for leaks, missing components, and structural damage during maintenance outages. Traditional manual inspection is time-consuming and poses safety risks from confined space entry. We developed an automated computer vision system for drone-based waterbox inspection in partnership with Florida Light and Power. Our approach uses feature detection and matching to identify critical changes between baseline and current inspection images, automatically flagging additions (leaks/debris), removals (missing plugs), and translations (displaced components) while compensating for drone movement and environmental variations. We systematically evaluated six feature matching methods, from classical approaches (SIFT+BF) to state-of-the-art neural networks (SuperPoint+SuperGlue), using both standard benchmarks (HPatches) and waterbox-specific validation with real-world augmentations. SuperPoint+SuperGlue achieved superior performance with 7.82 pixels RMSE and 100% success rate—2.8x better accuracy than our baseline. While the pre-trained model has commercial licensing restrictions for nuclear deployment, our findings validate this architecture for custom training. We implemented a real-time GUI demonstrating the SIFT+BF approach for immediate deployment, processing drone feeds at 30 FPS with color-coded change visualization. Future work includes training a custom SuperPoint+SuperGlue model on waterbox data and integrating Vision-Language Models for automated reporting and maintenance guidance.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2020

Surface Amorphization of Vanadium Dioxide (B) for K-ion Battery

Given the merits of low cost, fast ionic transport in electrolyte, and high operating voltage, potassium ion batteries (PIBs) are promising alternatives to lithium-ion batteries. However, developing suitable electrode materials that can reversibly accommodate large potassium ions is a great challenge. In this paper, guided by density functional theory (DFT) calculations, it is demonstrated that the strategy of interfacial engineering via surface amorphization of VO 2 (B) nanorods (SA-VO 2 ), which results in the formation of a crystalline core/amorphous shell heterostructure, enables superior K + storage performance in terms of large capacity, outstanding rate capability, and long cycle stability working as an anode for PIBs. DFT calculations reveal that the created crystalline/amorphous heterointerface in SA-VO 2 can substantially lower the surface energy, narrow the band gap, and reduce the K + diffusion barrier of VO 2 (B). These conditions enable enhanced K + storage capacity and rapid K + /electron transfer, which result in large capacity and outstanding rate capability. Using in situ X-ray diffraction and in situ transmission electron microscopy complemented by ex situ microscopic and spectroscopic techniques, it is unveiled that the superior cycling stability originates from the excellent phase reversibility with negligible strain response and robust mechanical behavior of SA-VO 2 upon (de)potassiation.

25 ENERGY STORAGE↗