Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sub-scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Circumventing mesh bias by r- and h-adaptive techniques for variational eigenfracture

This work introduces and compares mesh r- and h-adaptivity for the eigenfracture model originally proposed in Schmidt et al. (Multiscale Model Simul 7:1237–1266, 2009), Pandolfi and Ortiz (J Numer Methods Eng 92:694–714, 2012), with the goal of suppressing potential mesh bias due to the element deletion. In the r-adaptive approach, we compute the configurational force at each incremental step and move nodes near the crack tip parallel to the normalized configurational forces field such that the crack propagation direction can be captured more accurately within each incremental step. In the h-adapative approach, we introduce mesh refinement via a quad-tree algorithm to introduce more degrees of freedom within the nonlocal ϵ-neighborhood such that a more refined crack path can be reproduced with a higher mesh resolution. Our numerical examples indicate that the r-adaptive approach is able to replicate curved cracks and complex geometrical features, whereas the h-adaptive approach is advantageous in simulating sub-scale fracture when the nonlocal regions are smaller than the un-refined coarse mesh.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A multiscale multi-permeability poroplasticity model linked by recursive homogenizations and deep learning

Many geological materials, such as shale, mudstone, carbonate rock, limestone and rock salt are multi-porosity porous media in which pores of different scales may co-exist in the host matrix. When fractures propagate in these multi-porosity materials, these pores may enlarge and coalesce and therefore change the magnitude and the principal directions of the effective permeability tensors. The pore-fluid inside the cracks and the pores of host matrix may interact and exchange fluid mass, but the difference in hydraulic properties of these pores often means that a single homogenized effective permeability tensor field is insufficient to characterize the evolving hydraulic properties of these materials at smaller time scale. Furthermore, the complexity of the hydro-mechanical coupling process and the induced mechanical and hydraulic anisotropy originated from the micro-fracture and plasticity at grain scale also makes it difficult to propose, implement and validate separated macroscopic constitutive laws for numerical simulations. Here this article presents a hybrid data-driven method designed to capture the multiscale hydro-mechanical coupling effect of porous media with pores of various different sizes. At each scale, data-driven models generated from supervised machine learning are hybridized with classical constitutive laws in a directed graph that represents the numerical models. By using sub-scale simulations to generate database to train material models, an offline homogenization procedure is used to replace the up-scaling procedure to generate cohesive laws for localized physical discontinuities at both grain and specimen scales. Through a proper homogenization procedure that preserves spatial length scales, the proposed method enables field-scale simulations to gather insights from meso-scale and grain-scale micro-structural attributes. This method is proven to be much more computationally efficient than the classical DEM–FEM or FEM2 approach while at the same time more robust and flexible than the classical surrogate modeling approach. Due to the usage of bridging-scale technique, the proposed model may provide multiple opportunities to incorporate different types of simulations and experimental data across different length scales for machine learning. Numerical issues will also be discussed.

42 ENGINEERING↗

A manufacturing process design for producing a membrane-based energy recovery ventilator with high aspect ratio support ribs

Heating, ventilation, and air conditioning systems represent nearly half of building energy usage in the United States. Recent building regulations requiring increased air turnover within buildings will result in even greater air conditioning usage. To alleviate these concerns, membrane-based heat-and-moisture exchangers known as energy recovery ventilators have been developed to reduce the energy expenditure of air conditioning systems by pre-conditioning incoming air through sensible and latent heat transfer with building air exhaust. Here in this work, we propose and validate a manufacturing process design for channel lamination based on surface mount adhesives capable of meeting the process requirements of a membrane-based ventilator. In particular, the device requires rib supports with height-to-width aspect ratios greater than one. The proposed manufacturing process design is capable of meeting this process requirement by stretching the adhesive after initial adhesive tacking. A manufacturing process flow diagram, a machine tool specification and a cost model are proposed for meeting process requirements. A set of design constraints are developed detailing the adhesive requirements necessary for meeting requirements. The cost model is validated by building a sub-scale mesochannel array demonstrating the ability to meet process requirements. Results show that additional work is needed to validate the curing step but that the process is capable of producing a mesochannel array with an acceptable level of variation.

42 ENGINEERING↗

Three-dimensional (3D) analysis of white etching bands (WEBs) in AISI M50 bearing steel using automated serial sectioning

Dark etching regions (DER) and white etching bands (WEB) form in the subsurface stressed regions of bearing raceways and rolling elements. Also, “butterfly” formations form around non-metallic inclusions and large carbides. The formation of WEBs, DERs and butterfly are dependent on operating conditions, material alloying elements and heat treatment. The DER, WEB and butterfly formations are well studied in two dimensions (2D). The objective of this study was to analyze WEB formation in three dimensions (3D) that will allow better understanding of material transformation after stress cycling. Three rolling contact fatigue (RCF) tested vacuum induction melted vacuum arc re-melted (VIM-VAR) AISI M50 samples (from a bench test, sub-scale test and commercial gas turbine engine) were analyzed using automated serial sectioning to map WEB networks and a butterfly formation in 3D. Automated serial sectioning and 2D optical microstructural data for 3D reconstructions and analysis was done using a fully automated serial sectioning system – Robo-Met.3D®. 3D analysis was performed using Image-Pro Premier 3D. The data set allowed 3D visualization and analysis of the evolution and propagation of WEB and butterfly in M50 bearing steel, including the positive microscopic identification of a ceramic inclusion that was the source of a WEB.

36 MATERIALS SCIENCE↗

Property optimized energy absorber for automotive bumpers utilizing multi-material and structural design strategies

This study proposes a novel design for automotive bumper using optimized lattice structures and multi-materials to balance low-speed collision and high-speed pedestrian impact performance. Different blends of 20 % carbon fiber-reinforced acrylonitrile butadiene styrene with thermoplastic polyurethane were used to tailor material properties. The energy absorber features lattice structures with customized mechanical responses, created by varying the incline angle θ from 0 to 180°. We conducted 576 finite element simulations on a half-scale model to optimize energy absorption and stiffness, leading to 66 optimized designs that met both low-speed and high-speed impact criteria. Two sub-scale optimized energy absorbers with different peak forces—both meeting low-speed impact requirements—were 3D printed and validated through drop-weight testing. The one with lower peak stress demonstrated a more compliant response, exhibiting approximately 90 % lower initial peak force and an increase in energy absorption of around 33 % (from 24 J to 32 J). Compared to the baseline triangular lattice, the optimized absorber increased energy absorption by 68 % from (19 J to 32 J) and reduced peak stress by 70 %. It also showed near-complete recovery with minimal fractures, making it suitable for repeated use. This design improves safety while offering a lightweight, durable, and cost-effective bumper system.

36 MATERIALS SCIENCE↗

Additively manufactured and cast high-temperature aluminum alloys for electric vehicle brake rotor application

Electric vehicle brake rotors demand lightweight, high thermal conductivity materials with good resistance to wear, creep, salt corrosion, and thermal fade, all of which present challenges to the traditionally used cast iron. In this work, we investigated the braking performance of recently developed high-temperature aluminum alloys in both cast and 3D printed forms, that possess excellent microstructural and mechanical stability at elevated temperatures. Three aluminum alloys, Al-6Cu-Mn-Zr, Al-9Cu-Mn-Zr, and Al-Ce-Ni-Mn-Zr and a reference cast iron were tested on a sub-scale brake tester against a commercial brake pad material over a range of sliding speeds between 2 and 15 m/s. The performance of these alloys was evaluated for wear resistance, friction behavior, temperature elevation, and surface morphological change. Although all three candidate alloys had lower wear-resistance than cast iron, Al-Ce-Ni-Mn-Zr showed a significantly reduced wear rate in comparison to the Al-Cu-Mn-Zr alloys. Moreover, Al-Ce-Ni-Mn-Zr alloy had the most consistent friction behavior at all sliding speeds and good fade resistance, as the coefficient of friction did not dramatically decrease with temperature rise but stayed within a desirable range of 0.35–0.50 instead. The superior wear resistance and braking performance of the Al-Ce-Ni-Mn-Zr alloy were attributed to its higher hardness, and high temperature yield strength and creep resistance compared with the Al-Cu-Mn-Zr alloys. In conclusion, the results suggest that the braking performance of these aluminum alloys could be further enhanced by increasing the hardness and forming a more stable transfer layer on the sliding surface.

36 MATERIALS SCIENCE↗

Hydro-instability growth of perturbation seeds from alternate capsule-support strategies in indirect-drive implosions on National Ignition Facility

Hydrodynamic instability growth of the capsule support membranes (or “tents”) and fill tubes has been studied in spherical, glow discharge polymer plastic capsule implosions at the National Ignition Facility (NIF). In NIF implosions, the capsules are supported by tents because the nominal 10-μm thick fill tubes are not strong enough to support capsules by themselves. After it was recognized that the tents had a significant impact of implosion stability, new support methods were investigated, including thicker, 30-μm diameter fill tubes and cantilevered fill tubes, as described in this article. A new “sub-scale” version of the existing x-ray radiography platform was developed for measuring growing capsule perturbations in the acceleration phase of implosions. It was calibrated using hydrodynamic growth measurements of pre-imposed capsule modulations with Legendre modes of 60, 90, 110, and 140 at convergence ratios up to ~2.4. Subsequent experiments with 3-D perturbations have studied instability growth of 10-μm and 30-μm thick fill tubes to compare them with 30-nm thick tent perturbations at convergence ratios up to ~3. In other experiments, the perturbations from cantilevered fill tubes were measured and compared to the tent perturbations. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by 100 μm, 200 μm, and 300 μm from the capsule surfaces. Based on these experiments, 30-μm thick fill tubes and 300-μm offset cantilevered fill tubes were recommended for further tests using layered deuterium-tritium implosions. In conclusion, the effects of x-ray shadowing during the drive and oxygen-induced perturbations during target assembly produced additional seeds for instabilities and were also measured in these experiments.

42 ENGINEERING↗

High-compression implosions based on high density carbon ablator using modified drive and capsule dopant profiles

Laser-driven inertial fusion experiments have, for the first time, achieved a target gain greater than unity in a laboratory setting [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Despite this breakthrough, the burn-up fraction remains limited to about one-fourth of ideal estimates due to insufficient areal density, highlighting the potential for greater gains through enhanced compression. In our previous work, we demonstrated record-high compression of stagnated fuel in indirectly driven implosions using high-density carbon ablators. This was achieved by combining a continuous ramped pulse drive with a modified ablator dopant profile, which reduced mixing at the fuel–ablator interface and improved stability [Tommasini et al., Phys. Rev. Res. 5, L042034 (2023)]. Based on this foundation, the study presented here investigates the limits of compression achievable by combining the continuous ramped pulse drive with different dopant profiles to further minimize unstable interfaces and gradient discontinuities, thereby reducing fuel–ablator mixing. Our results demonstrate that the continuous ramped pulse consistently outperforms designs based on 3-shock drive pulses across all ablator profiles studied, with compression showing only a relatively modest dependence on dopant configurations that reduce the number of interfaces or eliminate discontinuities in the dopant gradient profile. Sub-scale experiments using the continuous ramped pulse achieved compression levels exceeding those of full-scale “HyE” implosions [Kritcher et al., Phys. Plasmas 28, 072706 (2021)] at similar adiabat, anticipating significant performance gains with increased scale, as supported by models and simulations. These findings underscore the critical role of the continuous ramped pulse in reducing mix and achieving improved compression. They also provide a foundation for future large-scale experiments to test the continuous ramped pulse design on deuterium–tritium fuel in the burn-wave propagation regime, leveraging the most effective combinations of continuous ramped pulse and dopant profiles identified in this study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of CLIQ on Training of HL-LHC Quadrupole Magnets

The high-luminosity LHC upgrade requires stronger than LHC low-beta quadrupole magnets to reach the luminosity goals of the project. The project is well advanced and HL-LHC quadrupole magnets are currently being commissioned in US Labs (MQXFA magnets) and CERN (MQXFB magnets). Those are the first Nb 3 Sn magnets to be used in any large particle accelerator. At development stages, many Nb 3 Sn accelerator sub-scale models showed relatively slow training and MQXFA magnets were projected to have low tens of quenches before reaching operational field. Recently it was shown that dedicated capacitor-based de-vices can affect Nb 3 Sn magnet training, and it was suggested that CLIQ, a capacitor-based device intended for quench protection, can do too. Here, the present paper investigates effects on training likely induced by CLIQ, using the base fact that only half the coils in a quadrupole experience upward current modulation at quench because of capacitor discharge. The study encompasses all MQXFA production magnets trained at BNL to date. No other high-statistics data from identical magnets (series) with CLIQ protection exist so far. Implications and opportunities stemming from data analysis are discussed and conclusions drawn.

43 PARTICLE ACCELERATORS↗

A Scalable Compact Additively Manufactured Molten Salt to Supercritical Carbon Dioxide Heat Exchanger for Solar Thermal Application

Design of an additively manufactured molten salt (MS) to supercritical carbon dioxide (sCO 2 ) primary heat exchanger (PHE) for solar thermal power generation is presented. The PHE is designed to handle temperatures up to 720 °C on the MS side and an internal pressure of 200 bar on the sCO 2 side. In the core, MS flows through a three-dimensional periodic lattice network, while sCO 2 flows within pin arrays. The design includes integrated sCO 2 headers located within the MS flow, allowing for a counterflow design of the PHE. The sCO 2 headers are configured to enable uniform flow distribution into each sCO 2 plate while withstanding an internal pressure of 200 bar and minimizing obstruction to the flow of MS around it. The structural integrity of the design is verified on additively manufactured (AM) 316 stainless steel sub-scale specimens. An experimentally validated, correlation-based sectional PHE core thermofluidic model is developed to study the impact of flow and geometrical parameters on the PHE performance, with varied parameters including the mass flowrate, surface roughness, and PHE dimensions. A process-based cost model is used to determine the impact of parameter variation on build cost. The model results show that a heat exchanger with a power density of 18.6 MW/m 3 (including sCO 2 header volume) and effectiveness of 0.88 can be achieved at a heat capacity rate ratio of 0.8. As a result, the impact of design and AM machine parameters on the cost of the PHE are assessed.

14 SOLAR ENERGY↗

Advanced High Torque Density Magnetically Geared Generator

The objective of this research project was to investigate the fundamental torque density limitations of multistage flux focusing magnetic gears and magnetically geared direct-drive generators for wind turbines. Magnetic gears create non-contact speed amplification by modulating the air-gap magnetic field harmonics created by magnetic rotors. By integrating a stator into the magnetic gear structure a very high torque density direct-drive generator can be created. Magnetic geared systems offer unique capabilities that are currently not available using existing mechanically geared systems, such as overload protection. Magnetic gears also offer the potential for higher reliability, higher efficiency and quieter operation than is currently achievable using a mechanically geared generator. By increasing reliability and design life magnetic gears could decrease the overall life-cycle costs when compared with equivalent mechanical or direct-drive drivetrains. This research project investigated and experimentally testing two sub-scale magnetic gearboxes (0.12 m diameter) and two large diameter magnetic gearboxes (0.56m and 0.63m diameter). The goal of the project was to demonstrate a torque density >300Nm/L for a multistage magnetic gearbox with integrated stator. A nested multistage magnetic gear structure was first proposed and studied. However, it was shown that the nested design greatly increased mechanical complexity and therefore a two-stage series typology was utilized. A multi-stage magnetic gear with a 59:1 gear ratio was successfully experimentally tested. A peak torque of 4.25 kN·m was measured and this resulted in an overall active region torque density of 141 N·m/L (when including support rings). The torque density was significantly reduced from what was computed using 2-D electromagnetic analysis. This reduction was due to the 3-D edge effects, increased power losses and the inclusion of additional mechanical support rings as well as other mechanical assembly design changes. At large diameters contiguous lamination parts could not be fabricated and so a segmented laminated rotor design had to be used. This reduced the mechanical strength of the design when compared to small diameter magnetic gears and resulted in the need for the addition of mechanical support rings to prevent deflection. The final experimentally tested design also had a high torque ripple and the power loss within the magnetic gear did not change significantly with load. This therefore resulted in the efficiency being high only at peak loads. Despite not experimentally achieving the 2-D calculated high torque density the analysis has shown that the problems encountered with the scaling can be overcome with careful design changes. For example, understanding the unique mechanical deflection requirements during the electromagnetic design of the large diameter magnetic gears is key to achieving both a high torque density based on the electromagnetic analysis and a high torque density based on the mechanical support needs. Furthermore, ensuring that end plates are made of non-conductive material and minimizing other conductive support elements within the magnetic structure is a key requirement for reducing eddy current losses. In summary, if the mechanical design can be made more robust and eddy current loss mitigation strategies are used in the mechanical design phase then the magnetic gear is capable of being scaled up whilst operating at a very high torque density. This will then enable it to be potentially performance and cost competitive with alternative direct-drive and mechanically geared wind turbine drivetrains.

17 WIND ENERGY↗

Computational Design and Development of a New, Lightweight Cast Alloy for Advanced Cylinder Heads in High-Efficiency, Light-duty Engines

The objective of the collaborative multi-year Cast Lightweight Alloy program was to develop a new, lightweight, cast aluminum alloy for automotive engines with better high temperature properties than the incumbent alloys (B319, A356, A356+0.5Cu) to allow for more efficient engine operation. The program kicked off with the generation of alloy concepts and selecting alloy models with specific milestones for establishing property requirements, generating design concepts and selecting models for casting design. Following this, sub-scale prototypes of the promising design concepts were cast and characterized in order to validate the design concepts and develop data for subsequent model calibration and improvement. Using the calibrated models, a set of alloy designs were created. This first generation set of designs were validated through production and characterization of lab-scale castings. With the learnings from the lab-scale prototypes and the improvements in the computational models, final embodiment design of the new alloy was completed. The final alloy designs were cast at lab-scale and also at component-scale to characterize its final properties. An alloy recyclability analysis and cost modelling was also performed.

36 MATERIALS SCIENCE↗

High Yield, Economical and Environmentally Benign Production of Rare Earth Elements from Coal Ash [Abstract]

Fly ash stored in landfills and ponds across the United States is an attractive, abundant domestic resource for the cost-effective recovery of rare earth elements (REE) and other critical minerals (CM). Physical Sciences Inc. (PSI) and its team members, Winner Water Services (WWS) and University of Kentucky/Center for Applied Energy Research (UK/CAER) successfully executed a multiphase program that developed and demonstrated pilot plant operations for cost-effective and environmentally-friendly production of rare earth element oxide (REO) concentrates, and the critical minerals scandium and aluminum (in the forms of salts or oxide products). We constructed and operated a sub-scale (0.5 kg/day) micropilot facility to demonstrate the key physical and chemical processing operations, predict yields, and troubleshoot process bottlenecks. The project team then designed, constructed and operated two decoupled pilot plant operations: (1) an operational pilot plant for physical separation processes with a capacity of 0.4 metric tons per day (tpd) where we optimized processes to produce selected ash fractions as the feedstock for chemical processing as well as valuable byproducts such as cement substitute, cenospheres, magnetic ash and secondary fuel carbon, and (2) an operational pilot plant for chemical processing with a capacity of 0.5 tpd that developed optimized processes for the production of: (a) REO concentrates, (b) critical minerals recovery (Sc, Al), and (c) beneficiated ash as valuable byproduct suitable for cement applications.

01 COAL, LIGNITE, AND PEAT↗

Electrochemical Hydrogen Compression Cell Design (CRADA Final Report)

Electrochemical compression and purification is a high potential technology that is likely to outcompete mechanical compression for hydrogen end use applications. However, testing and understanding what is occurring within the cell is difficult as it is not readily accessible through experimentation. Thus, the main target is to increase performance and reduce cost of electrochemical hydrogen compression (EHC) and purification (EHP) cells and stacks using multiscale mathematical modeling informed by experiment. The models can provide physical insight into limiting processes and develop mitigation methods, which can be proven out through rapid sub-scale testing of the devices.

08 HYDROGEN↗

Effect of CLIQ on training of HL-LHC quadrupole magnets

The high-luminosity LHC upgrade requires stronger than LHC low-beta magnets to reach the luminosity goals of the project. The project is well advanced and HL-LHC quadrupole magnets are currently being commissioned in US Labs (MQXFA magnets) and CERN (MQXFB magnets). Those are the first Nb3Sn magnets to be used in any large particle accelerator. At development stages, many Nb3Sn accelerator sub-scale models showed relatively slow training and MQXFA magnets were projected to have low tens of quenches before reaching operational field. Recently it was shown that dedicated capacitor-based devices can affect Nb3Sn magnet training, and it was suggested that CLIQ, a capacitor-based device intended for quench protection, can do too. The present paper investigates effects on training induced by CLIQ, using the base fact that only half the coils in a quadrupole experience upward current modulation because of the capacitor discharge. The study encompasses all MQXFA production magnets trained at BNL to date. No other high-statistics data from identical magnets (series) with CLIQ protection exists so far. Implications and opportunities stemming from data analysis are discussed and conclusions drawn.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Additively Manufactured, Lightweight, Low-Cost Composite Vessels for Compressed Natural Gas Fuel Storage

This project will develop a process to combine AM via direct ink writing (DIW) technology for CFC printing and to use design optimization tools pioneered at LLNL, with advances in resin/composite formulation enabled by chemical and nano-material modification to produce lightweight low-cost CNG tanks. Our approach will yield sub-scale prototype composite pressure tanks equivalent to Type-5 CNG vessel designs that demonstrate a potential cost-benefit advantage. Central to our vision is using agile AM and design based on computationally informed DIW of both short and continuous CF, further coupled with high-performance thermoset polymer matrixes modified by emergent nanomaterials. Our single-stage, multi-material AM technology, combined with a decreased volume fraction of CF and an increased proportion of economically advantaged short fiber, all together drive the reduction in manufacturing time and overall cost. Importantly, reductions in continuous fiber and overall fiber volume fraction will be achieved without detriment to the mechanical strength of the composite vessel. This will be achieved by employing a single process using multi materials grading involving a thermoset resin “ink” modified with aligned nanoplatelets to leverage the efficient tortuous-path gas barrier effect, printed as an inner flexible gas barrier as the initial stage in our manufacturing process before compositionally grading the AM feedstock in real-time to transition to a rigid, structural CF-filled resin. The proposed hybrid construction is projected to achieve pressure ratings at a service range of 2,900–3,600 psi with a 3× burst safety factor comparable to conventional filament-wound composite tanks with an estimated 30–50% reduction in total manufacturing cost.

03 NATURAL GAS↗

Testing high-current superconducting subscale dipole coils with superconducting transformer

Several sub-scale superconducting dipole coils are being developed at Fermilab in the framework of the U.S. Magnet Development Program. These coils are made of high-current LTS and HTS cables with maximum currents of up to 10 kA. A superconducting current transformer with a maximum DC current up to ~25 kA previously developed at Fermilab for Nb3Sn Rutherford cable testing was modified and adapted for small dipole coil testing. This paper describes its commissioning using a NbTi dipole magnet impregnated with TELENE. This magnet was wound out of 6/1 NbTi cable.

Barzi, Emanuela↗

Laser Powder Bed Fusion Additive Manufacture Nb1Zr Development

Next generation fission and fusion nuclear reactors require materials that can withstand operating temperatures greater than 500 °C, neutron irradiation doses of up to 200 displacements per atom (dpa), and potentially corrosive coolants such as the alkali liquid metals sodium, lithium, and NaK (Na33K eutectic alloy). Refractory alloys, such as Nb1Zr (Nb-1wt%Zr) and Molybdenum alloy TZM (Mo-0.5wt%Ti-0.08wt%Zr) have been traditionally considered viable candidates for advanced fission and fusion reactor concepts. However, it is relatively difficult to generate complex geometries of interest from these alloys using traditional manufacturing methods. In addition, there needs to be a concentrated effort to address refractory metal challenges at elevated temperature operation. In order to generate complex geometries of interest, modern manufacturing techniques are considered to increase the technological readiness level (TRL), cost-effectiveness, and schedule savings. This work focused on the continued development of laser powder bed fusion (L-PBF) additive manufacturing (AM) to improve both design flexibility, evaluate microstructure and properties, and ultimately accelerate the TRL and qualification of these processes and alloys for components to potentially be put into service. Niobium alloy Nb1Zr was identified through a down-selection process outlined in previous reports as a candidate to develop in L-PBF AM. Historically, Nb1Zr had been explored for high temperature fast spectrum fission reactors for both terrestrial and space applications. Molybdenum alloy TZM has also been considered for these reactor concepts due to exceptional high-temperature strength, creep resistance, and stability under irradiation. L-PBF AM of TZM has previously been investigated at LANL under the Microreactor program, NASA, ORNL, and in academia. However, due to the crack prone nature of TZM, L-PBF AM of TZM resulted in significant microcracking and additional development is required to pursue viable maturation. Other AM methods have been found to be more successful in printing TZM, and those alternatives approaches are discussed in this effort. The efforts detailed in this report focused on continued development of Nb1Zr through L-PBF and development of TZM via L-PBF and electron powder bed fusion (E-PBF). The objective of this work was to further the development of these AM techniques for the chosen refractory alloys, elucidating and addressing associated challenges through characterization of several demonstration builds. At LANL, Nb1Zr builds were completed using an EOS M290 and M400 machines, and a refractory alloy-dedicated L-PBF system, the Xact Metal XM200G, was installed. The XM200G primary purpose was to do the Nb1Zr parameter development process; however, due to difficulties associated with the machine installation and qualification process, it was decided to pivot development to the larger M400 and M290 machines. Although the supply of Nb1Zr powder was limited, it was sufficient to generate sub-scale metallographic specimens for the purpose of parameter development. This was first accomplished on the EOS M400 then the M290 due to machine schedule availability. Further development of TZM has been initiated at the University of Texas El Paso (UTEP) under contract with LANL to use both a heated build envelope L-PBF machine and E-PBF machine that have been found in the literature to mitigate microcracking. UTEP was provided with TZM powder and build plates to support parallel TZM parameter development across both machines. As part of the contract, UTEP will also be conducting microstructural characterization once optimized process parameters have been identified. The optimized process parameters for each machine will be used to generate a series of metallographic, mechanical, and surface finish specimens for subsequent characterization and testing. In the next section, we provide a detailed discussion of the methodology used for investigating the feasibility of leveraging these alloys for use in advanced reactor applications.

36 MATERIALS SCIENCE↗