Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sparse estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

MME-based attitude dynamics identification and estimation for SAMPEX

A method is described for obtaining optimal attitude estimation algorithms for spacecraft lacking attitude rate measurement devices (rate gyros), and then demonstrated using actual flight data from the Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX) spacecraft. SAMPEX does not have on-board rate sensing, and relies on sun sensors and a three-axis magnetometer for attitude determination. Problems arise since typical attitude estimation is accomplished by filtering measurements of both attitude and attitude rates. Rates are nearly always sampled much more densely than are attitudes. Thus, the absence/loss of rate data normally reduces both the total amount of data available and the sampling density (in time) by a substantial fraction. As a result, the sensitivity of the estimates to model uncertainty and to measurement noise increases. In order to maintain accuracy in the attitude estimates, there is increased need for accurate models of the rotational dynamics. The proposed approach is based on the minimum model error (MME) optimal estimation strategy, which has been successfully applied to estimation of poorly modeled dynamic systems which are relatively sparsely and/or noisily measured. The MME estimates may be used to construct accurate models of the system dynamics (i.e. perform system model identification). Thus, an MME-based approach directly addresses the problems created by absence of attitude rate measurements.

Depena, Juan↗
NASA NTRS2016

Investigation of Unsteady Pressure-Sensitive Paint (uPSP) and a Dynamic Loads Balance to Predict Launch Vehicle Buffet Environments

This NESC assessment examined the accuracy of estimating buffet loads on in-line launch vehicles without booster attachments using sparse unsteady pressure measurements. The buffet loads computed using sparse sensor data were compared with estimates derived using measurements with much higher spatial resolution. The current method for estimating launch vehicle buffet loads is through wind tunnel testing of models with approximately 400 unsteady pressure transducers. Even with this relatively large number of sensors, the coverage can be insufficient to provide reliable integrated unsteady loads on vehicles. In general, sparse sensor spacing requires the use of coherence-length-based corrections in the azimuthal and axial directions to integrate the unsteady pressures and obtain reasonable estimates of the buffet loads. Coherence corrections have been used to estimate buffet loads for a variety of launch vehicles with the assumption methodology results in reasonably conservative loads. For the Space Launch System (SLS), the first estimates of buffet loads exceeded the limits of the vehicle structure, so additional tests with higher sensor density were conducted to better define the buffet loads and possibly avoid expensive modifications to the vehicle design. Without the additional tests and improvements to the coherence-length analysis methods, there would have been significant impacts to the vehicle weight, cost, and schedule. If the load estimates turn out to be too low, there is significant risk of structural failure of the vehicle. This assessment used a combination of unsteady pressure-sensitive paint (uPSP), unsteady pressure transducers, and a dynamic force and moment balance to investigate the integration schemes used with limited unsteady pressure data by comparing them with direct integration of extremely dense fluctuating pressure measurements. An outfall of the assessment was to evaluate the potential of using the emerging uPSP technique in a production test environment for future launch vehicles. The results show that modifications to the current technique can improve the accuracy of buffet estimates. More importantly, the uPSP worked remarkably well and, with improvements to the frequency response, sensitivity, and productivity, will provide an enhanced method for measuring wind tunnel buffet forcing functions (BFFs).

Schuster, David M.↗
NASA NTRS1975

Satellite microwave observations of soil moisture variations

The electrically scanning microwave radiometer (ESMR) on the Nimbus 5 satellite was used to observe microwave emissions from vegetated and soil surfaces over an Illinois-Indiana study area, the Mississippi Valley, and the Great Salt Lake Desert in Utah. Analysis of microwave brightness temperatures (T sub B) and antecedent rainfall over these areas provided a way to monitor variations of near-surface soil moisture. Because vegetation absorbs microwave emission from the soil at the 1.55 cm wavelength of ESMR, relative soil moisture measurements can only be obtained over bare or sparsely vegetated soil. In general T sub B increased during rainfree periods as evaporation of water and drying of the surface soil occurs, and drops in T sub B are experienced after significant rainfall events wet the soil. Microwave observations from space are limited to coarse resolutions (10-25 km), but it may be possible in regions with sparse vegetation cover to estimate soil moisture conditions on a watershed or agricultural district basis, particularly since daily observations can be obtained.

Schmugge, T. J.↗
NASA NTRS1976

Quantitative mapping of rainfall rates over the oceans utilizing Nimbus-5 ESMR data

The electrically scanning microwave radiometer (ESMR) data from the Nimbus 5 satellite was used to deduce estimates of precipitation amount over the oceans. An atlas of the global oceanic rainfall was prepared and the global rainfall maps analyzed and related to available ground truth information as well as to large scale processes in the atmosphere. It was concluded that the ESMR system provides the most reliable and direct approach yet known for the estimation of rainfall over sparsely documented, wide oceanic regions.

Rao, M. S. V.↗
NASA NTRS1989

A one- and two-layer model for estimating evapotranspiration with remotely sensed surface temperature and ground-based meteorological data over partial canopy cover

Surface-air temperature differences are commonly used in a bulk resistance equation for estimating sensible heat flux (H), which is inserted in the one-dimensional energy balance equation to solve for the latent heat flux (LE) as a residual. Serious discrepancies between estimated and measured LE have been observed for partial-canopy-cover conditions, which are mainly attributed to inappropriate estimates of H. To improve the estimates of H over sparse canopies, one- and two-layer resistance models that account for some of the factors causing poor agreement are developed. The utility of the two models is tested with remotely sensed and micrometeorological data for a furrowed cotton field with 20 percent cover and a dry soil surface. It is found that the one-layer model performs better than the two-layer model when a theoretical bluff-body correction for heat transfer is used instead of an empirical adjustment; otherwise, the two-layer model is better.

Kustas, William P.↗
NASA NTRS2007

Status of the L2 and Lunar Charged Particle Environment Models

The L2 Charged Particle Environment (L2-CPE) model is an engineering tool which provides free field charged particle environments for distant magnetotail, magnetosheath, and solar wind environments. L2-CPE is intended for use in assessing contributions from low energy radiation environments (4.1 keV to few MeV) to radiation dose in thin materials used in construction of spacecraft to be placed in orbit about the Sun-Earth L2 point. This paper describes the status of the current version of the L2-CPE model including structure of the model used to organize plasma environments into solar wind, magnetosheath, and magnetotail environments, the algorithms used to estimate radiation fluence in sparsely sampled environments, the updated graphical user interface, and output options for flux and fluence environments. In addition, we describe the status and plans for updating the model to include environments relevant to lunar programs.

Minow, Joseph I.↗
NASA NTRS1994

Integrated Tail Buffet Loads on the F/A-18

The unsteady pressures acting on the vertical tails of a full-scale F/A-18 fighter aircraft were studied to gain a better understanding of tail-buffet loads that frequently occur on fighter aircraft operating at high angles-of-attack. Data for the study were acquired during two test entries in the 80- by 120-Foot Wind Tunnel wherein the aircraft was tested at wind speeds up to 100 knots and at angles-of-attack from 20deg to 40deg. For the purposes of this paper, the primary difference between the two tests is that, during the first wind-tunnel entry, the pressure transducers were more sparsely spaced and covered less of the fin than during the second entry. In addition to a brief description of the spectral analysis methods used for the unsteady aerodynamic pressures and loads, an analysis of the effects of sensor density on estimating integrated loads is presented. It was found that the integrated loads determined from sparse sensor arrays are significantly higher than actual loads. However, a modest increase in the number of sensors can greatly reduce the error and a method for correcting load estimates from sparse sensor arrays is also suggested. The results for the time-averaged, power-spectral analysis are then presented for the tail-fin bending moments. Power spectra are presented for the aircraft at zero sideslip over an angle-of-attack range from 20deg to 40deg and for the aircraft at an angle-of-attack of 30deg over a sideslip range from -16deg to 16deg. Since the aircraft was equipped with a removable leading-edge extension (LEX) fence to reduce tail-buffet loads, the tail-fin bending moment loads are also presented for that configuration. The LEX fence is shown to significantly reduce bending moment loads over a broad range frequencies, for all the aircraft attitudes presented.

Meyn, Larry A.↗
NASA NTRS2021

Locating the Isolator Shock-Train Leading Edge with Limited Pressure Information

Real-time detection and control of the isolator shock-train leading edge (STLE) is important to the performance of high-speed air-breathing engines, such as dual-mode scramjets. Typically, the STLE location is determined using wall static-pressure measurements, but there are often restrictions on the placement and overall number of the pressure transducers, reducing the viability and accuracy of such approaches. To address these issues, we introduce the adaptive pressure profile (APP) method for estimating the STLE location. This method does not require extensive prior characterization of the isolator or engine model. Instead, it uses real-time pressure measurements from a small number of transducers to adaptively learn the isolator pressure profile and subsequently uses this deduced profile to estimate the STLE location in a data-driven manner. The APP method works well in situations with sparse transducer placement. It produces accurate estimates when the STLE location is 1) not bounded by two or more transducers or 2) between two transducers that are several isolator duct heights apart. We demonstrate the efficacy of the APP method using simulations and experimental data from direct-connect isolator models. This validation shows that the APP method is accurate and robust for different flow regimes, transducer configurations, and model geometries.

Gregory J. Hunt↗
NASA NTRS1998

TRMM Observations of Lightning and Rainfall

A multi-sensor algorithm is proposed that uses total lightning observations in conjunction,with conventional weather satellite imagery to develop proportionality relationships that can be used to improve space-time estimates of rainfall in data sparse regions. Previous studies have examined the relationships between rainfall and cloud-to-ground lightning only. The proposed algorithm is developed from relationships developed between total lightning and rainfall data collected at the TRMM ground validation site at Kennedy Space Center, Florida and elsewhere. The algorithm is evaluated throughout the tropics with data collected by the TRMM Lightning Imaging Sensor (LIS) and the other TRMM instruments. Based on earlier studies of relationships among total lightning, passive microwave ice scattering signatures, and cloud top height, this algorithm is expected to improve rainfall estimates from geosynchronous orbit. A lightning sensor is currently being designed for a future flight on the GOES satellite.

Goodman, S. J.↗
NASA NTRS1991

Discrete Kalman filtering equations of second-order form for control-structure interaction simulations

A second-order form of discrete Kalman filtering equations is proposed as a candidate state estimator for efficient simulations of control-structure interactions in coupled physical coordinate configurations as opposed to decoupled modal coordinates. The resulting matrix equation of the present state estimator consists of the same symmetric, sparse N x N coupled matrices of the governing structural dynamics equations as opposed to unsymmetric 2N x 2N state space-based estimators. Thus, in addition to substantial computational efficiency improvement, the present estimator can be applied to control-structure design optimization for which the physical coordinates associated with the mass, damping and stiffness matrices of the structure are needed instead of modal coordinates.

Park, K. C.↗
NASA NTRS2012

A Sparse Matrix Approach for Simultaneous Quantification of Nystagmus and Saccade

The vestibulo-ocular reflex (VOR) consists of two intermingled non-linear subsystems; namely, nystagmus and saccade. Typically, nystagmus is analysed using a single sufficiently long signal or a concatenation of them. Saccade information is not analysed and discarded due to insufficient data length to provide consistent and minimum variance estimates. This paper presents a novel sparse matrix approach to system identification of the VOR. It allows for the simultaneous estimation of both nystagmus and saccade signals. We show via simulation of the VOR that our technique provides consistent and unbiased estimates in the presence of output additive noise.

Kukreja, Sunil L.↗
NASA NTRS2021

Comparison of Monthly IMERG Precipitation Estimates with PACRAIN Atoll Observations

Satellite-based precipitation estimates provide valuable information where surface observations are not readily available, especially over the large expanses of the ocean where in situ precipitation observations are very sparse. This study compares monthly precipitation estimates from the Integrated Multisatellite Retrievals for GPM (IMERG) with gauge observations from 37 low-lying atolls from the Pacific Rainfall Database for the period June 2000–August 2020. Over the analysis period, IMERG estimates are slightly higher than the atoll observations by 0.67% with a monthly correlation of 0.68. Seasonally, DJF shows excellent agreement with a near-zero bias, while MAM shows IMERG is low by 4.6%, and JJA is high by 1.2%. SON exhibits the worst performance, with IMERG overestimating by 6.5% compared to the atolls. The seasonal correlations are well contained in the range 0.67–0.72, with the exception of SON at 0.62. Furthermore, SON has the highest RMSE at 4.70 mm day^(−1), making it the worst season for all metrics. Scatterplots of IMERG versus atolls show IMERG, on average, is generally low for light precipitation accumulations and high for intense precipitation accumulations, with best agreement at intermediate rates. Seasonal variations exist at light and intermediate rate accumulations, but IMERG consistently overestimates at intense precipitation rates. The differences between IMERG and atolls vary over time but do not exhibit any discernible trend or dependence on atoll population. The PACRAIN atoll gauges are not wind-loss corrected, so application of an appropriate adjustment would increase the precipitation amounts compared to IMERG. These results provide useful insight to users as well as valuable information for future improvements to IMERG.

David T. Bolvin↗
NASA NTRS1999

Incorporating TRMM and Other High-Quality Estimates into the One-Degree Daily (1DD) Global Precipitation Product

The One-Degree Daily (1DD) precipitation dataset was recently developed for the Global Precipitation Climatology Project (GPCP). The IDD provides a globally-complete, observation-only estimate of precipitation on a daily 1 deg x 1 deg grid for the period 1997 through late 1999 (by the time of the conference). In the latitude band 40 N - 40 S the IDD uses the Threshold-Matched Precipitation Index (TMPI), a GPI-like IR product with the T(sub b) threshold and (single) conditional rain rate determined locally for each month by the frequency of precipitation in the GPROF SSNU product and by the precipitation amount in the GPCP satellite-gauge (SG) combination. Outside 40 N - 40 S the 1DD uses a scaled TOVS precipitation estimate that has adjustments based on the TMPI and the SG. This first-generation 1DD has been in beta test preparatory to release as an official GPCP product. In this paper we discuss further development of the 1DD framework to allow the direct incorporation of TRMM and other high-quality precipitation estimates. First, these data are generally sparse (typically from low-orbit satellites), so a fair amount of work was devoted to data boundaries. Second, these data are not the same as the original 1DD estimates, so we had to give careful consideration to the best scheme for forcing the 1DD to sum to the SG for the month. Finally, the non-sun-synchronous, low-inclination orbit occupied by TRMM creates interesting variations against the sun-synchronous, high-inclination orbits occupied by the Defense Meteorological Satellite Program satellites that carry the SSM/I. Examples will be given of each of the development issues, then comparisons will be made to daily raingauge analyses.

Huffman, George J.↗
NASA NTRS2000

Validation and Development of the GPCP Experimental One-Degree Daily (1DD) Global Precipitation Product

The One-Degree Daily (1DD) precipitation dataset has been developed for the Global Precipitation Climatology Project (GPCP) and is currently in beta test preparatory to release as an official GPCP product. The 1DD provides a globally-complete, observation-only estimate of precipitation on a daily 1 deg. x 1 deg. grid for the period 1997 through early 2000 (by the time of the conference). In the latitude band 40N-40S the 1DD uses the Threshold-Matched Precipitation Index (TMPI), a GPI-like IR product with the pixel-level T(sub b) threshold and (single) conditional rain rate determined locally for each month by the frequency of precipitation in the GPROF SSM/I product and by, the precipitation amount in the GPCP monthly satellite-gauge (SG) combination. Outside 40N-40S the 1DD uses a scaled TOVS precipitation estimate that has month-by-month adjustments based on the TMPI and the SG. Early validation results are encouraging. The 1DD shows relatively large scatter about the daily validation values in individual grid boxes, as expected for a technique that depends on cloud-sensing schemes such as the TMPI and TOVS. On the other hand, the time series of 1DD shows good correlation with validation in individual boxes. For example, the 1997-1998 time series of 1DD and Oklahoma Mesonet values in a grid box in northeastern Oklahoma have the correlation coefficient = 0.73. Looking more carefully at these two time series, the number of raining days for the 1DD is within 7% of the Mesonet value, while the distribution of daily rain values is very similar. Other tests indicate that area- or time-averaging improve the error characteristics, making the data set highly attractive to users interested in stream flow, short-term regional climatology, and model comparisons. The second generation of the 1DD product is currently under development; it is designed to directly incorporate TRMM and other high-quality precipitation estimates. These data are generally sparse because they are observed by low-orbit satellites, so a fair amount of work must be devoted to analyzing the effect of data boundaries. This work is laying, the groundwork for effective use of the NASA Global Precipitation Mission, which will have full Global coverage by low-orbit passive microwave satellites every three hours.

Huffman, George J.↗
NASA NTRS2014

NASA Tech Briefs, March 2014

Topics include: Data Fusion for Global Estimation of Forest Characteristics From Sparse Lidar Data; Debris and Ice Mapping Analysis Tool - Database; Data Acquisition and Processing Software - DAPS; Metal-Assisted Fabrication of Biodegradable Porous Silicon Nanostructures; Post-Growth, In Situ Adhesion of Carbon Nanotubes to a Substrate for Robust CNT Cathodes; Integrated PEMFC Flow Field Design for Gravity-Independent Passive Water Removal; Thermal Mechanical Preparation of Glass Spheres; Mechanistic-Based Multiaxial-Stochastic-Strength Model for Transversely-Isotropic Brittle Materials; Methods for Mitigating Space Radiation Effects, Fault Detection and Correction, and Processing Sensor Data; Compact Ka-Band Antenna Feed with Double Circularly Polarized Capability; Dual-Leadframe Transient Liquid Phase Bonded Power Semiconductor Module Assembly and Bonding Process; Quad First Stage Processor: A Four-Channel Digitizer and Digital Beam-Forming Processor; Protective Sleeve for a Pyrotechnic Reefing Line Cutter; Metabolic Heat Regenerated Temperature Swing Adsorption; CubeSat Deployable Log Periodic Dipole Array; Re-entry Vehicle Shape for Enhanced Performance; NanoRacks-Scale MEMS Gas Chromatograph System; Variable Camber Aerodynamic Control Surfaces and Active Wing Shaping Control; Spacecraft Line-of-Sight Stabilization Using LWIR Earth Signature; Technique for Finding Retro-Reflectors in Flash LIDAR Imagery; Novel Hemispherical Dynamic Camera for EVAs; 360 deg Visual Detection and Object Tracking on an Autonomous Surface Vehicle; Simulation of Charge Carrier Mobility in Conducting Polymers; Observational Data Formatter Using CMOR for CMIP5; Propellant Loading Physics Model for Fault Detection Isolation and Recovery; Probabilistic Guidance for Swarms of Autonomous Agents; Reducing Drift in Stereo Visual Odometry; Future Air-Traffic Management Concepts Evaluation Tool; Examination and A Priori Analysis of a Direct Numerical Simulation Database for High-Pressure Turbulent Flows; and Resource-Constrained Application of Support Vector Machines to Imagery.

Source record↗
NASA NTRS2017

Snow Accumulation Variability on a West Antarctic Ice Stream Observed with GPS Reflectometry, 2007-2017

Land ice loss from Antarctica is a significant and accelerating contribution to global sea level rise; however, Antarctic mass balance estimates are complicated by insufficient knowledge of surface mass balance processes such as snow accumulation. Snow accumulation is challenging to observe on a continental scale and in situ data are sparse, so we largely rely on estimates from atmospheric models. Here we employ a novel technique, GPS interferometric reflectometry (GPS-IR), to measure upper (less than 2 m) firn column thickness changes across a 23-station GPS array in West Antarctica. We compare the results with antenna heights measured in situ to establish the method's daily uncertainty (0.06 m) and with output from two atmospheric reanalysis products to categorize spatial and temporal variability of net snow accumulation. GPS-IR is an effective technique for monitoring surface mass balance processes that can be applied to both historic GPS data sets and future experiments to provide critical in situ observations of processes driving surface height evolution.

snow↗
NASA NTRS1990

Ground and aircraft infrared observations over a partially-vegetated area

Consideration is given to the feasibility of estimated a reliable composite surface temperature over a partially-vegetated and furrowed cotton field with an intensive ground sampling routing using hand-held radiometers. The ground-based data are compared with surface temperatures taken from an aircraft at an altitude of about 150 m. A simple model is presented for computing the composite surface temperature using component temperatures of the soil and vegetation and row crop dimensions and orientations. The results of the modeling are compared with the ground-based and airborne radiometric measurements. It is found that estimates of the composite surface temperature comparable to low-flying aircraft observations over row crops with sparse cover may be obtained using ground-based estimates of average canopy temperature.

Kustas, W. P.↗
NASA NTRS1986

Development of algorithms for understanding the temporal and spatial variability of the earth's radiation balance

A brief description is given of how temporal and spatial variability in the earth's radiative behavior influences the goals of satellite radiation monitoring systems and how some previous systems have addressed the existing problems. Then, results of some simulations of radiation budget monitoring missions are presented. These studies led to the design of the Earth Radiation Budget Experiment (ERBE). A description is given of the temporal and spatial averaging algorithms developed for the ERBE data analysis. These algorithms are intended primarily to produce monthly averages of the net radiant exitance on regional, zonal, and global scales and to provide insight into the regional diurnal variability of radiative parameters such as albedo and long-wave radiant exitance. The algorithms are applied to scanner and nonscanner data for up to three satellites. Modeling of dialy shortwave albedo and radiant exitance with satellite samling that is insufficient to fully account for changing meteorology is discussed in detail. Studies performed during the ERBE mission and software design are reviewed. These studies provide quantitative estimates of the effects of temporally sparse and biased sampling on inferred diurnal and regional radiative parameters. Other topics covered include long-wave diurnal modeling, extraction of a regional monthly net clear-sky radiation budget, the statistical significance of observed diurnal variability, quality control of the analysis, and proposals for validating the results of ERBE time and space averaging.

Brooks, D. R.↗