Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “spark plasma sintering (SPS)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Graded microstructure and mechanical properties of spark plasma sintered Fe-Cr alloys

Developing graded microstructure and mechanical properties is critical for accelerating the design and optimization of structural materials for a wide range of applications. Here, in this study, Fe-Cr alloys were fabricated by spark plasma sintering (SPS) technique. The microstructure, microhardness, and tensile properties of the as-fabricated and thermally annealed variants were investigated. Graded grain structures were created in the as-fabricated cylinders along both axial and radial directions. Grain size was gradually reduced from the sample periphery to the center. Microhardness measurements reveal a gradual decrease of hardness towards the periphery of the samples. The as-fabricated Fe-Cr alloys show a desired combination of tensile strength and elongation, primarily due to the formation of a high density of oxides, voids, dislocations, and grain boundaries. After in-situ thermal annealing at 600 °C under 60 MPa for 2 h using SPS, the Fe-Cr alloys underwent minimal grain growth, and the graded grain structures were retained. The hardness was more uniformly distributed in the annealed variants, and the tensile strength was reduced with an increase in the total elongation, which is attributed to the dissolution of nano-sized oxide particles and the relief of the residual stress. This study demonstrates that SPS coupled with subsequent heat treatment can tailor the graded microstructure and control the mechanical properties of Fe-Cr alloys, showing potential applications in other alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Influence of Cryomilling on Crystallite Size of Aluminum Powder and Spark Plasma Sintered Component

The present investigation aims to develop nanocrystalline (NC) pure aluminum powders using cryomilling technique and manufacture bulk components using spark plasma sintering (SPS). The cryomilling was performed on pure Al powders for 2, 6, and 8 h. The cryomilled powders were then consolidated using SPS to produce bulk components. The particle morphology and crystallite size of the powders and the bulk SPS components were analyzed using scanning electron microscopy (SEM), X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the crystallite size of pure Al powders decreases with increased cryomilling time. The results also showed that the SPS at elevated temperatures resulted in a slight increase in crystallite size, however, the changes were insignificant. The mechanical properties of the bulk components were determined using a Vickers microhardness tester. The hardness of the cryomilled SPS component was determined to be three times higher than that of the unmilled SPS component. The mechanism for the reduction in crystallite size with increasing cryomilling time is discussed. This fundamental study provides an insight into the development of bulk nanomaterials with superior mechanical properties for automotive, aerospace, marine, and nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Selective laser sintering and spark plasma sintering of (Zr,Nb,Ta,Ti,W)C compositionally complex carbide ceramics

Abstract Two advanced manufacturing processes, spark plasma sintering (SPS) and selective laser sintering (SLS), have been developed for synthesis of (Zr,Nb,Ta,Ti,W)C compositionally complex carbide (CCC) via reactive sintering of a powder mixture of constitute monocarbides. X‐ray diffraction analysis confirmed that the single‐phase CCC can be formed by both SPS and SLS. While a homogenous microstructure with uniform metal element distributions was developed during SPS, three‐layer microstructures with a thin TiC‐rich layer and two TaC‐rich layers along with a TiO 2 ‐rich surface layer containing W nanoparticles were formed during SLS. In addition, cellular structures with W, Zr, and Ti element segregation and dislocations on cell boundaries were observed in the SLS‐CCC sample, indicating the effect of nonequilibrium conditions on microstructure formation during laser melting followed by rapid cooling and solidification process. Compared to the SPS‐CCC sample, the SLS‐CCC showed enhanced hardness and reduced thermal conductivity, which may be related to their unique cellular structures.

36 MATERIALS SCIENCE↗
NASA NTRS2023

Sintering Behaviors of ZrC, NbC, and TaC Mono-and Binary Carbides

Nuclear Thermal Propulsion (NTP) has undergone development as an alternate in-space propulsion system to traditional chemical propulsion methods since the 1950s. In an NTP system, the energy released from fission in the core is utilized as the heat source to directly heat a propellant for propulsion, rather than chemical combustion in a traditional rocket. NTP has many desirable capabilities including flexible mission launch dates and reduced transit times due to it’s capability for high specific impulse. One of the main challenges with NTP systems is the structural integrity of the fuel. The fuel form required in the reactor core must withstand temperatures above 2700 Kelvin. Ceramic-metallic matrix fuel, ceramic-ceramic matrix fuel, and solid solution carbide fuels are the three strongest candidates for the extreme environments. Solid solution carbides have the potential to exhibit promising behavior as a fuel form in an NTP system. Of the multiple refractory metal carbides of interest, here we focus on zirconium carbide (ZrC), niobium carbide (NbC), and tantalum carbide (TaC). ZrC, NbC, and TaC powders were consolidated in monocarbide (ZrC, NbC, and TaC) and bi-carbide (ZrC-NbC, ZrC-TaC, NbC-TaC) forms using spark plasma sintering (SPS). In addition to the pure endpoint carbides, the examined compositions of the various bi-carbides ranged from 25-75 mol%. The sintering temperatures, pressures, and hold times were varied to determine the ideal sintering conditions. Grain size analysis, Archimedes’ density, scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersion spectroscopy (EDS) were used to determine and characterize the grain size, ideal density, porosity, phase stability, and chemical composition of each sample. The data from each sample was then used to generate a Master Sintering Curve (MSC) unique to each monocarbide or bi-carbide.

nuclear thermal propulsion↗
DOE OSTI2020

Coupling of Spark Plasma Sintering with Advanced Modeling to Enable Process Scale-Up: Presentation to DOE-NE [Slides]

The research goal of this project is to develop at Idaho National Laboratory (INL) a first-of-its-kind Multiphysics Object-Oriented Simulation Environment (MOOSE)-based, multiscale, multiphysics spark plasma sintering (SPS) modeling and simulation code application, termed “Freya.” Freya will simulate the thermo-mechanical-electrical aspects of the SPS fabrication process and will be paired with lower length scale sub-models, such as phase-field, to predict the resulting microstructure. SPS is an advanced manufacturing process that can be used to solve a variety of material manufacturing challenges; however, this process is an extremely challenging problem for modeling and simulation. The SPS process is inherently multiphysics and multi-scale, with the macroscale electro-thermo-mechanical behavior linked intricately to the microstructure evolution of the part being sintered. Accurate modeling and simulation tools, specifically geared towards the SPS process, are needed to predict the influence of the multiple variables involved in the manufacturing process. Modeling and simulation accuracy is achieved and demonstrated through comparison to multiple validation experiments. The validation efforts for Freya include both separate effects and complete multiphysics SPS process experiments. One of the key benefits this Laboratory Directed Research & Development (LDRD) project offers stems from the emphasis placed on experimental validation of the Freya models, both on the individual length scales and of the final coupled multiscale multiphysics simulations. Experimental validation of Freya’s multiscale coupling capability provides the technical credibility necessary for potential future industry and research partners to accept the simulation predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

UO 2 + 5 vol% ZrB 2 nano composite nuclear fuels with full boron retention and enhanced oxidation resistance

The boron isotope ( 10 B) can be used as a neutron absorber in UO 2 to control the reactivity of nuclear fuel pellets, however, the boron source can react with oxygen source in UO 2 to form B 2 O 3 that vaporize readily at temperatures above 1200 °C. Unfortunately, the sintering of UO 2 fuel requires hours holding at high temperature (>1700 °C), resulting in an inevitable B loss during sintering and unpredictable B concentration in final product. It is challenging to incorporate boron through a conventional sintering method. In this work, we demonstrated that spark plasma sintering (SPS), a field assisted sintering technology, can effectively densify UO 2 + 5 vol% ZrB 2 composite fuel pellets by rapid consolidation at 1600 °C for a short duration of 5 min under an applied pressure of 40 MPa. Further, thermogravimetric analysis (TGA) measurements confirm that ZrB 2 is fully retained inside the composite fuel pellets. Inside the composite fuel pellets, nano sized ZrB 2 particles are uniformly distributed along the grain boundaries of the UO 2 matrix. The ZrB 2 particle transforms to a glassy B 2 O 3 phase covering the sample surface and grain boundaries of UO 2 matrix after a simple post-sintering annealing at 1000 °C in flowing Argon gas for 4 h. The formed glassy B 2 O 3 slows down the diffusion of oxygen ions and postpones the onset temperature for oxidation of UO 2 from 400 °C to 550 °C. This study demonstrates the capability of SPS, an advanced fuel manufacturing technique, to achieve a full retention of ZrB 2 in UO 2 oxide fuel and increase oxidation resistance through a simple post-sintering annealing. The reported work holds great engineering potential for development of advanced oxide fuel for nuclear application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Dislocation density in fine grain-size spark-plasma sintered aluminum measured using high brightness synchrotron radiation

In this study, three-dimensional orientation mapping of samples of aluminum prepared by spark plasma sintering (SPS) with average grain sizes of 5 μm and 1 μm has been carried out using high-brightness synchrotron radiation, from which the geometrically necessary dislocation (GND) density has been determined. The low average measured GND density values confirm that the SPS process can be used to produce samples containing grains with dislocation density similar to that of fully recrystallized coarse-grained samples. Values of GND density are also compared to those obtained from electron back-scatter diffraction studies on the same material, highlighting the significantly higher angular resolution of the synchrotron data. For the 5 μm grain-size sample the measured GND density can account for a large fraction of the previously observed positive Hall-Petch deviation of this material. For the 1 μm grain-size sample, however, the GND-based strengthening contribution is much smaller than the reported positive Hall-Petch deviation, such that the additional strength may be reliably associated with dislocation source-limited strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fabrication and thermophysical properties of UO 2 -UB 2 and UO 2 -UB 4 composites sintered via spark plasma sintering

Uranium dioxide (UO 2 ) composites with uranium diboride (UB 2 ) and uranium tetraboride (UB 4 ) have been proposed as advanced fuel candidates due to their high thermal conductivity, high melting point, high fissile density and their ability to incorporate a built-in burnable poison by tailoring the targeted 10 B/ 11 B ratio. As such, it is important to assess the fabrication, and thermal and micromechanical properties of such composites. In this work, UO 2 -UB 2 and UO 2 -UB 4 samples with boride phase fractions of 5, 15 and 30 wt% were fabricated to high densities (above 95 % theoretical density) via spark plasma sintering (SPS). This enabled sintering at relatively low temperatures and short timescales. SPS also aided in maintaining the target phase fractions of the samples as reactions between the constituent phases were suppressed due to the short timescales and reducing environment during sintering. Here, thermal diffusivity measurements from 299 to 1273 K were conducted through laser flash analysis (LFA). The diffusivity increased as a function of boride weight fraction, and UB 2 additions increased the thermal diffusivity of the composites more than UB 4 additions. Assessment of the LFA results indicated in-situ reactions between the UO 2 and boride phases that suppress the thermal diffusivity occur above 800 K for all samples. Oxidation of the boride phase was proposed as the underlying reaction. This was supported by thermodynamic assessments from the literature, as well as microstructural, crystallographic, and nanoindentation characterization performed on these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Additive manufacturing of high‐density silicon carbide ceramics through post‐processing spark plasma sintering

This research advances the field of additive manufacturing (AM) of silicon carbide (SiC) ceramics by integrating spark plasma sintering (SPS) to enhance material density, mechanical strength, and thermal properties. Traditional AM techniques struggle to achieve the high‐density SiC required for demanding applications, such as aerospace engineering, where high thermal conductivity and mechanical strength are paramount. Here, our study addresses these challenges by incorporating SPS as a post‐processing step, achieving near‐theoretical maximum densities and significantly reducing porosity, thereby resulting in outstanding thermal conductivity in SiC ceramics. We developed a specialized SiC ink optimized for 3D printing, ensuring structural integrity after deposition through tailored rheological properties. The application of SPS facilitates rapid, uniform sintering, essential for attaining superior density, mechanical properties, and thermal performance. Our experimental results, confirmed through scanning electron microscopy analysis, demonstrate significant microstructural properties, mechanical strength, and thermal conductivity, showcasing the effectiveness of integrating SPS in AM processes. This innovative approach not only expands the capabilities of AM in producing complex, high‐density ceramic structures but also broadens the potential applications of SiC in demanding environments.

36 MATERIALS SCIENCE↗
NASA NTRS2023

Homogeneity Study of ZrC, NbC, and TaC Binary Carbide Fuels for the Application of Nuclear Thermal Propulsion

In alignment with NASA and DARPA goals, efforts towards Nuclear Thermal Propulsion (NTP) have increased in recent years. As progress is made, a main challenge still exists; the fuel in an NTP system must survive the extreme environment experienced during operating conditions. Three fuel forms have been studied including a ceramic-metallic matrix, a ceramic-ceramic matrix, and solid solution carbides. Solid solution carbides were studied previously as a fuel for NTP and was shown to be a promising technology; however, the programs were canceled before demonstration in an NTP engine test. Of the refractory metal carbides of interest, zirconium carbide (ZrC), niobium carbide (NbC) and tantalum carbide (TaC) were studied. ZrC, NbC, and TaC powders were consolidated in monocarbide (ZrC, NbC, TaC) and bi-carbide (ZrC-NbC, ZrC-TaC, NbC-TaC) forms using spark plasma sintering (SPS), with 50-50 mol% compositions of the bi-carbides of interest. The time and temperature conditions to achieve a completely homogeneous solid solution for the mixed carbides is of interest for NTP fuel applications, since this homogeneity is considered to be essential for this fuel form. Homogeneity is typically not achieved during sintering, as surface diffusion (predominant for sintering to near ideal density) tends to occur at lower temperatures than bulk volumetric diffusion (required for solute interdiffusion to achieve a homogeneous solid solution). High temperature isochronal annealing was performed to identify the conditions to achieve a chemically homogeneous sample. The solute interpenetration vs annealing temperature was quantified using energy dispersion spectroscopy (EDS) in a scanning electron microscope (SEM). X-ray diffraction (XRD) was used to accurately measure the phase stability and lattice parameter as a function of annealing conditions. The diffusion data from each sample was then used to determine self-diffusion coefficients for interdiffusion of the Nb, Zr, and Ta solutes and compared to existing literature values. The minimum annealing conditions to achieve complete chemical homogeneity for each carbide was determined.

nuclear thermal propulsion↗
DOE OSTI2025

Entrapment Behavior of Solid Surrogate Fission Products at Engineered UN Nano‐Hetero‐Interfaces Within Metallic Nuclear Fuels

Nanometric hetero-interfaces provide a wealth of scientific and engineering opportunities due to their complex and often misunderstood properties that can differ from their respective bulk constituents. In this work, the ability for engineered nanostructures within a bulk U─Mo alloy to arrest simulant fission products is investigated experimentally and computationally. Nanostructured 90 wt% U/ 10 wt% Mo (U-10Mo) with 7.1 at% Nd is consolidated using spark-plasma- sintering (SPS) techniques and is heat-treated at 500 °C under vacuum for 24, 100, 500, and 1000 h. Analysis on the sintered and heat-treated U-10Mo reveals rapid kinetics in Nd diffusion to nanocluster sites, with evidence of Nd diffusion occurring during sintering and during the following heat-treatment. The segregation behavior of Nd at two different U─Mo/UN interfaces is computationally verified using density functional theory (DFT) to reinforce experimental data.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Synthesis, Characterization, and Testing of High-Lithium-Density Composite Breeders

Solid tritium breeder materials must first and foremost have sufficiently high concentrations of lithium to enable a plant-scale tritium breeding ratio greater than 1:1. However, in addition to lithium content, such breeder materials must also meet other performance metrics including high tritium release rates, thermal conductivities, and irradiation damage tolerance. Perhaps most importantly, tritium breeders must maintain their mechanical integrity during reactor operation so as to avoid degradation which can jeopardize the functionality of the tritium breeder blanket module, which in most designs takes the form of a pebble bed geometry. Unfortunately, the mechanical robustness of most lithium-bearing ceramics under investigation for fusion applications is often inversely related to the lithium atom density. For example, a material such as lithium oxide (Li2O), which has one of the highest lithium atom densities, has a much lower mechanical splitting strength than lithium metatitanate (Li2TiO3), though Li2TiO3 has less than half the lithium atom density of Li2O. This work seeks to provide an alternative to monolithic ceramic tritium breeders, in the form of metal-reinforced composite tritium breeders. Specifically, composite tritium breeders have been synthesized combining Li2O with various ferrous metal reinforcements via electric field assisted sintering (EFAS), also known as spark plasma sintering (SPS). As the metal reinforcement content is increased, metallic networks are observed, via electron microscopy and X-ray computed tomography, to form throughout the composite material. Through destructive mechanical testing, even dilute metal reinforcement loading enables drastic mechanical strength improvements over pure Li2O while higher loadings give rise to quasi-ductile behavior and higher ultimate strengths than Li2TiO3 – while still maintaining a higher density of lithium atoms than Li2TiO3 and many other breeder candidates. In addition to microstructural characterization and mechanical testing, thermal property measurements and hydrogen permeability testing are underway to further assess the suitability of such composites for fusion reactor applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Microstructure refinement of hot deformed Dy-free NdFeB magnets through a novel cold sintering approach by pressure-assisted spark plasma sintering

Anisotropic fine-grained Dy-free NdFeB high-performance magnets were produced using a novel cold sintering approach by pressure-assisted spark plasma sintering (SPS). The NdFeB nanocrystalline ribbon powders were subjected to cold sintering below 450 °C using pressure-assisted SPS, followed by hot deformation at 710 °C and 810 °C via SPS. Results indicate that cold sintering below 450 °C effectively restricts grain growth in the NdFeB magnets, yielding sub-100 nm scale grains across both fine-grained regions and most coarse-grained regions. The refined grain structure achieved through cold sintering allows for a lower hot deformation temperature as compared with the magnet by conventional sintering, as finer grains allow easier deformation and grain sliding/rotation. This process produces a highly fine-grained and anisotropic microstructure to achieve high magnetic performance (i.e., high intrinsic coercivity, remanence, and maximum energy product) in the magnets. The cold sintering (at 350 °C) and lower hot deformation temperatures required (e.g., 710 °C) help control grain coarsening and limit grain size that is commensurate with the size of a single magnetic domain of the Nd 2 Fe 14 B magnetic matrix phase, resulting in high intrinsic coercivity (H ci =11.4 kOe). Furthermore, the reduced hot deformation temperature mitigates the formation of coarse grain bands, leading to improved magnetic properties, specifically an increased remanence (B r = 14.3 kGs) and a high maximum energy product ((BH) max = 48 MGOe). In conclusion, cold sintered hot deformed NdFeB magnet also shows good thermal stability with reversible temperature coefficient α(B r )= -0.097 %/K and α(H ci )= -0.616 %/K at elevated temperatures up to 400 K.

Cold Sintering↗
DOE OSTI2020

Densification and oxidation behavior of spark plasma sintered Hafnium Diboride-Hafnium Carbide composite

This study reports on the sintering and oxidation behaviors of Hafnium Diboride (HfB 2 ) and Hafnium Carbide (HfC) based ultra-high temperature ceramic (UHTC) composites. Pure Hafnium Diboride, Hafnium Carbide, and HfB 2 -50 vol% HfC composite were consolidated using spark plasma sintering (SPS) without the use of sintering aids. HfB 2 -HfC composite displayed a high sintered density of 98% as compared to 87% density of pure HfB 2 . The increased density of the HfB 2 -HfC composite is attributed to the bimodal powder distribution, which allowed for the smaller HfC particle to occupy the voids between the larger HfB 2 particles resulting in improved packing efficiency. Moreover, the higher planar surface energy, for the (111) and the (200) planes for HfC, contributed to the smaller HfC particle being a significant driving force in the sintering process. Oxidation studies of each material were carried out by exposing them to a high-speed plasma jet in a temperature exceeding 2700 °C. The results of these studies show an improved oxidation resistance of HfB 2 -HfC composite by 54% and 70% over pure HfC and HfB 2 , respectively. The enhanced oxidation behavior is attributed to B 2 O 3 filling in the porosity between the HfO 2 scale and protecting the underlying material. This study provides a new alternative to improve the sinterability of UHTC diborides by introducing another UHTC (i.e., HfC) to form a fully dense composite without sintering aid and superior oxidation resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhancement in Mechanical Properties of Bulk Nanocrystalline Aluminum by Grain Boundary Strengthening Mechanism

In the present work, commercially pure aluminum (Al) powders were milled at cryogenic temperatures (a) without magnesium (Mg) and (b) with 5 wt.% Mg powders for different durations. The cryomilled powders were analyzed using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and x-ray diffraction (XRD) to determine the changes in particle morphology, elemental composition, and crystallite size. The results showed a reduction in crystallite size with the increase in cryomilling duration. Thereafter, the spark plasma sintering (SPS) process was carried out to manufacture bulk samples. The mechanical properties of the bulk SPS samples were assessed by conducting microhardness, tensile, and fatigue tests. The Vickers microhardness tests showed improved hardness for the Al-Mg bulk samples as compared to pure Al. The Al-Mg samples also showed an increase in tensile strength with increasing cryomilling time. Fatigue test results showed an improvement in Al-Mg components' high-cycle fatigue response. Furthermore, the mechanism for the enhancement in mechanical properties as a result of crystallite size reduction and grain boundary strengthening by the addition of Mg dopant is also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantification of complex protective surface oxide layer formed during plasma jet exposure of multicomponent ultra-high temperature carbides

Multicomponent ultra-high temperature ceramics (MC-UHTCs) has garnered attention due to their improved thermo-mechanical and oxidation properties. MC-UHTC was progressively formed by adding a UHTC component at each step, producing binary, ternary and quaternary UHTC systems, processed by spark plasma sintering (SPS). Here, we investigate the role of multi-elements and thermochemical stability of the surface oxide layer formed during plasma arc jet exposure (T > 2500 °C) of MC-UHTCs using core-level X-ray photoelectron spectroscopy (XPS) correlated with the structural investigation. The results indicate that adding a UHTC component improves oxidation resistance due to the assemblage of refractory phases forming complex mixed oxides via preferential oxidation. XPS spectra of Ta4f, Nb3d, Ti1p, and Hf4f showed that the nature of the chemical bonds switched from metal carbides to metal oxides (metal oxy-carbides) in the binary system with retained metal carbides in ternary and quaternary UHTCs. The absence of a metal carbide peak in the high-resolution C1s scan of the binary system also supports this finding. The principal complex mixed oxide phases emanate in the exiguous oxidation of MC-UHTCs are quantified using Rietveld analysis. Overall, this study suggests that MC-UHTC is a promising material for possible application in thermal protection systems (TPS).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spark plasma sintered, MoNbTi-based multi-principal element alloys with Cr, V, and Zr

MoNbTi, MoNbTiZr, CrMoNbTiZr, and MoNbTiVZr multi-principal element alloys (MPEAs) were fabricated via spark plasma sintering (SPS) and investigated for use in high-strength applications. The fabrication method by SPS and powder metallurgy differs from those presented in the prior literature, where most MPEAs are fabricated using arc melting (AM) methods. Here cryogenic milling was used to maximize potential defect sinks (grain boundaries) for radiation resistance and to increase ultimate tensile strength through the Hall-Petch effect. SPS was chosen for consolidation in order to maintain a fine-grained structure during densification. Each alloy was characterized using x-ray diffraction and scanning electron microscopy for phase identification and compositional homogeneity. The base ternary alloy MoNbTi presented a predominantly single BCC system with minor cubic phases. The introduction of additional alloying elements—Zr, V, and Cr—heightened the phase complexity and increased the fractions of a secondary BCC phase and an HCP phase from Zr. The addition of Cr induced a larger fraction of the Laves phase to form. The addition of V caused the precipitation of small Mo inclusions. Thermodynamic analysis was performed to understand the separation of phases in each alloy. Discrepancies among the phase predictions generated by thermodynamic models, phases previously presented in the literature, and the characterization results suggest that MPEA fabrication methods, especially solid-state methods, require significant investigation to ensure that alloys can remain stable throughout their anticipated service lifetimes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A novel design of transitional layer structure between reduced activation ferritic martensitic steels and tungsten for plasma facing materials

Plasma-facing components (PFCs) are among the most critical gaps for fusion energy to establish technical and economic feasibility. Tungsten as a first wall/blanket material in PFCs requires to be integrating with reduced activation ferritic martensitic (RAFM) steels as a structural component. Currently, major drawbacks are the requirement of brazing, the formation of a brittle interface, and a large difference between the coefficients of thermal expansion of tungsten and steel. Here, a novel transitional multilayer structure was designed and investigated to join tungsten and RAFM steels using three interlayers. The composition of each interlayer was selected based on computational thermodynamics and diffusion kinetics to ensure a body-centered cubic (bcc) single-phase structure and prevent the formation of a brittle intermetallic phase region in the temperature range of 600–1150 °C. Although the transitional layer structure was designed for additive manufacturing, spark plasma sintering (SPS) as proof of concept was used to bond the individual layers. Interfaces were investigated using scanning and transmission electron microscopy methods but no layered intermetallic phase was observed. Nanoindentation maps across the interface suggest major hardness differences at the interface between tungsten and the vanadium interlayer, as well as the interface between RAFM steel and the FeCrAl interlayer.

36 MATERIALS SCIENCE↗