High-field liquid-neon-cooled electromagnets.
High field liquid-neon-cooled superconducting electromagnet for cryogenic solid state research
CRYOGENIC MAGNET↗
SEARCH · Engineering Papers
Results for “solid neon”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cryogenic cooling for spacecraft sensors, instruments, and experiments
Several disciplines requiring in-space cryogenic cooling are identified including high-energy, gamma-ray, and IR astronomy, relativity missions, and superconducting devices. Radiant coolers are limited in terms of temperature ranges and cooling loads. Other spacecraft cryogenic systems include stored solid cryogenic coolers using materials such as hydrogen, neon, argon, and methane. Two such cooler designs are described including one for the Nimbus F limb radiance inversion radiometer and one for the Nimbus G limb infrared monitoring of the atmosphere. Suggestions for increasing the performance of solid cryogenic coolers are made, such as a multimission cooler, a mechanical refrigerator, Stirling-cycle refrigerators, and Vuilleumier mechanized coolers. Techniques for obtaining cryogenic cooling in the milli-K range are identified as dilution refrigeration and adiabatic demagnetization.
Sherman, A.↗
Distribution of gases within Apollo 15 samples - Implications for the incorporation of gases within solid bodies of the solar system.
The distribution of helium, neon, and argon isotopes within Apollo 15 samples results primarily from fractionated solar wind gases, accompanied by small quantities of cosmogenic gases. No unequivocal primordial lunar gases have been detected within various mineral, rock, or glass fragments. A vug from 15555 contains solar wind gases that have abundance ratios similar to those found in the Apollo 12 aluminum foil experiments. A comparison of these Apollo 15 results with previous laser probe mass spectrometric measurements from the gas-rich Kapoeta and Fayetteville meteorites, as well as with analyses of the Apollo 12 and 14 samples, indicates that the mechanism of solar wind implantation, followed by subsequent fractionation of the gases by impact brecciation and heating, was primarily responsible for the incorporation of the original gas phase within solid bodies of the solar system.
Megrue, G. H.↗
Paramagnetic Attraction of Impurity-Helium Solids
Impurity-helium solids are formed when a mixture of impurity and helium gases enters a volume of superfluid helium. Typical choices of impurity gas are hydrogen deuteride, deuterium, nitrogen, neon and argon, or a mixture of these. These solids consist of individual impurity atoms and molecules as well as clusters of impurity atoms and molecules covered with layers of solidified helium. The clusters have an imperfect crystalline structure and diameters ranging up to 90 angstroms, depending somewhat on the choice of impurity. Immediately following formation the clusters aggregate into loosely connected porous solids that are submerged in and completely permeated by the liquid helium. Im-He solids are extremely effective at stabilizing high concentrations of free radicals, which can be introduced by applying a high power RF dis- charge to the impurity gas mixture just before it strikes the super fluid helium. Average concentrations of 10(exp 19) nitrogen atoms/cc and 5 x 10(exp 18) deuterium atoms/cc can be achieved this way. It shows a typical sample formed from a mixture of atomic and molecular hydrogen and deuterium. It shows typical sample formed from atomic and molecular nitrogen. Much of the stability of Im-He solids is attributed to their very large surface area to volume ratio and their permeation by super fluid helium. Heat resulting from a chance meeting and recombination of free radicals is quickly dissipated by the super fluid helium instead of thermally promoting the diffusion of other nearby free radicals.
Bernard, E. P.↗
Spectroscopic evidence for the Fe3+ spin transition in iron-bearing δ-AlOOH at high pressure
δ-AlOOH has emerged as a promising candidate for water storage in the lower mantle and could have delivered water into the bottom of the mantle. To date, it still remains unclear how the presence of iron affects its elastic, rheological, vibrational, and transport properties, especially across the spin crossover. In this study, we conducted high-pressure X-ray emission spectroscopy experiments on a δ-(Al 0.85 Fe 0.15 ) OOH sample up to 53 GPa using silicone oil as the pressure transmitting medium in a diamond-anvil cell. We also carried out laser Raman measurements on δ-(Al 0.85 Fe 0.15 )OOH and δ-(Al 0.52 Fe 0.48 )OOH up to 57 and 62 GPa, respectively, using neon as the pressure-transmitting medium. Evolution of Raman spectra of δ-(Al 0.85 Fe 0.15 )OOH with pressure shows two new bands at 226 and 632 cm –1 at 6.0 GPa, in agreement with the transition from an ordered ( P 2 1 nm ) to a disordered hydrogen bonding structure ( Pnnm ) for δ-AlOOH. Similarly, the two new Raman bands at 155 and 539 cm –1 appear in δ-(Al 0.52 Fe 0.48 )OOH between 8.5 and 15.8 GPa, indicating that the incorporation of 48 mol% FeOOH could postpone the order-disorder transition upon compression. On the other hand, the satellite peak ( K β') intensity of δ-(Al 0.85 Fe 0.15 )OOH starts to decrease at ~30 GPa and it disappears completely at 42 GPa. That is, δ-(Al 0.85 Fe 0.15 )OOH undergoes a gradual electronic spin-pairing transition at 30–42 GPa. Furthermore, the pressure dependence of Raman shifts of δ-(Al 0.85 Fe 0.15 )OOH discontinuously decreases at 32–37 GPa, suggesting that the improved hydrostaticity by the use of neon pressure medium could lead to a relatively narrow spin crossover. Notably, the pressure dependence of Raman shifts and optical color of δ-(Al 0.52 Fe 0.48 )OOH dramatically change at 41–45 GPa, suggesting that it probably undergoes a relatively sharp spin transition in the neon pressure medium. Together with literature data on the solid solutions between δ-AlOOH and ε-FeOOH, we found that the onset pressure of the spin transition in δ-(Al,Fe)OOH increases with increasing FeOOH content. These results shed new insights into the effects of iron on the structural evolution and vibrational properties of δ-AlOOH. The presence of FeOOH in δ-AlOOH can substantially influence its high-pressure behavior and stability at the deep mantle conditions and play an important role in the deep-water cycle
58 GEOSCIENCES↗
Rocket vehicle surface reflectance measurement during retro-rocket firing.
Reflectance variation of painted surface during solid propellant retrorocket firing on surface measured by helium-neon laser
Adams, R. N.↗
Electronic absorption spectroscopy of matrix-isolated polycyclic aromatic hydrocarbon cations. I - The naphthalene cation (C10H8/+/)
The ultraviolet, visible, and near-infrared absorption spectra of naphthalene (C10H8) and its radical ion (C10H8/+/), formed by vacuum ultraviolet irradiation, were measured in argon and neon matrices at 4.2 K. The associated vibronic band systems and their spectroscopic assignments are discussed together with the physical and chemical conditions governing ion production in the solid phase. The absorption coefficients were calculated for the ion and found lower than previous values, presumably due to the low polarizability of the neon matrix.
Salama, F.↗
Design and Testing of a Prototype Eddy Current Actuated Valve for the ITER Shattered Pellet Injection System
Reliably mitigating disruptions is essential for ITER to meet its long-term operational research plan without damage to the in-vessel components. Currently, the shattered pellet injection (SPI) technique is the most effective radiator of thermal energy and has been chosen for the baseline disruption mitigation system (DMS) for ITER. The SPI process uses cryogenic temperatures to desublimate material into the barrel of a pipe gun forming a solid cylindrical pellet. Pellets for ITER will initially be hydrogen and hydrogen-neon mixtures. Once formed, pellets are dislodged and accelerated using high-pressure gas (40-60 bar) delivered by a fast-opening valve. The solenoid valves currently used for SPI experiments will not operate in an ITER environment due to the large background magnetic field. An ITER prototype fast-opening valve, called a flyer plate valve (FPV), has been designed and has undergone a wide range of testing. The FPV operates by pulsing current through a pancake coil that is closely coupled with a ``flyer plate.'' The flyer plate is an aluminum plate in which eddy currents are generated creating a repulsive force from the pancake coil. The force generated in the flyer plate rapidly lifts the valve tip off the seat and delivers a pulse of gas to the rear of the pellet, breaking it free from the barrel and accelerating the pellet downstream to its intended target. The design of the valve has been iterated on over the lifetime of this project, as the DMS for ITER shifted from massive gas injection (MGI) to SPI. The most recent design has been tested, and operational ranges have been mapped. The valve must survive 3000+ cycles in an ITER-like magnetic field. The principal functional requirement of this valve is to reliably dislodge and accelerate hydrogen (or H-Ne mixture) pellets into ITER. The valve was mated with an ITER SPI test stand and has been shown to be capable of launching pellets reliably. The valve and power supply design will be discussed in this article, along with the various testing setups used to determine the feasibility of this valve for use on ITER.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Ortho- and paratritium.
Heat conductivity cell, cooled with liquid neon, is used to measure conversion of ortho-paratritium in the homogeneous gas and solid phases
PHASE CHANGE↗
Detection of the isotopes of heavy cosmic ray nuclei
A counter telescope designed to detect and resolve the isotopic composition of cosmic ray nuclei heavier than neon is being prepared. The telescope consists of a rather conventional charge measuring array using two scintillator elements and two solid Cerenkov radiators of differing refractive index. The mass measurement is obtained by combining the velocity information from one or both of the Cerenkov radiators operating near their threshold with residual range measured in a block of nuclear emulsion. Path length corrections and particle location in the emulsions is provided by a spark chamber fired in coincidence with potentially suitable particles. The telescope has a geometry factor of 530 sq cm sr roughly. It should be able to resolve the isotopes of iron over the energy range of 300 to 720 Mev/n and those of neon over 300 to 400 MeV/n. The expected response and characteristics of the telescope are described in detail and the sensitivity to rare isotopes discussed.
Gilman, C. M.↗
The Pioneer 10/11 and Helios A/B cosmic ray instruments
This paper describes the design and performance of a set of cosmic-ray particle experiments for the Pioneer 10/11 and Helios A/B space missions. These experiments had to be very light-weight, low-power and electronically sophisticated in order to meet the spacecraft and scientific requirements. Both sets of missions use several solid-state detector telescopes to measure protons from 100 KeV to 800 MeV and heavier ions up to Neon at 200 MeV per nucleon. Good performance is required for 7-8 years, and the system must tolerate large vibration loads and ionizing radiation doses up to 500,000 rads.
Stilwell, D. E.↗
Prediction of thermal acoustic oscillations (TAOs) in the CLAES solid CO2/neon system
Results are presented of a study initiated to investigate the possibility that the existence of thermal acoustic oscillations (TAOs) in the Cryogenic Limb Atmospheric Etalon Spectrometer (CLAES) neon plumbing system ground configuration could be the cause of higher-than-predicted heat rates measured during thermal ground testing. Tests were conducted between warm boundary temperatures ranging from 40 to 100 K, which simulated the actual test conditions of the CLAES CO2/neon system. TAOs were observed between 6 and 106 Torr, which agreed with the analytical predictions, and verified the possible existence of TAOs in the CLAES system during ground testing. The presence of TAOs was eventually confirmed in the CLAES system during a subsequent thermal test and were determined to have caused the higher heat rates measured during the prior thermal test.
Spradley, I. E.↗
Disruption thermal load mitigation with shattered pellet injection on the Joint European Torus (JET)
Disruption mitigation remains a critical, unresolved challenge for ITER. To aid in addressing this challenge, a shattered pellet injection (SPI) system was installed on JET and experiments conducted at a range of thermal energy fractions and stored energies in excess of 7 MJ. The primary goals of these experiments were to investigate the efficacy of the SPI on JET and the ability of the plasma to assimilate multiple pellets. Single pellet injections produced a saturation in total radiated energy (Wrad) with increasing injected neon content, suggesting total radiation of stored thermal energy. Further increases in injected neon quantities resulted in reduced cooling times and current quench (CQ) durations, indicating higher impurity assimilation. No significant variation in CQ duration or W rad was observed when varying the deuterium content at fixed neon quantities. Additionally, higher assimilation, inferred by shorter CQ durations, was measured when a mechanical punch was used to launch the pellets and this was attributed to a lower pellet velocity leading to higher solid content in the pellet plume and larger fragments penetrating deeper into the plasma. Radiation asymmetries averaged over the cooling time were inferred from Emis3D and ranged from 1.6 to 1.9. Asymmetries averaged over the entire disruption sequence were found to increase at higher thermal energy fractions. The radiated energy fractions decreased with increasing thermal energy fractions but this trend was eliminated when toroidal asymmetries were accounted for with Emis3D. Pure deuterium pellets were able to produce cooling times of up to 75 ms with a gradual loss in thermal stored energy of up to 80%. Experiments with multiple pellet injection indicated W rad can be increased through pellet superposition and density can be increased with an additional D2 injection without a reduction in W rad . KPRAD modelling accurately reproduced the cooling times and the CQ duration at high thermal energies. Assimilation estimates from KPRAD indicated CQ rates scale strongly whilst W rad scales weakly and saturates with assimilated neon content. Comparable W rad can be achieved with lower assimilated neon quantities as longer cooling times are attained. Thus reduced neon content can be preferential in a thermal load mitigation scheme as it may reduce radiation asymmetries and prevent flash melting.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Measurement of Elemental Abundance of Very Low Energy Solar Cosmic Rays
Heavy interplanetary particles were observed during a solar flare period between October 29 and November 4, 1972. The nuclear abundance was determined by a two parameter analysis (dE/dx vs E technique) of a thin window proportional counter - solid state detector device aboard the Explorer 47 (IMP-7) satellite. Energy spectra are given for C, O and Fe. The elemental abundance relative to oxygen is determined for carbon, neon, magnesium, silicon and the iron group in the energy range 0.62 to 6.9 MeV/nucleon. For the Fe/O ratio no energy dependence could be observed within the error limits.
Hovestadt, D.↗
Measurement of elemental abundance of very low energy solar cosmic rays
Heavy interplanetary particles (Z from 3 to 30) have been observed during a solar flare period between October 29 and November 4, 1972. The nuclear abundance has been determined by a two parameter analysis of a thin window proportional counter - solid state detector device aboard the Explorer 47 (IMP-7) satellite. Energy spectra are given for C, O and Fe. The elemental abundance relative to oxygen is determined for carbon, neon, magnesium, silicon and the iron group in the energy range 0.62 to 6.9 MeV/nucleon. For the Fe/O ratio no energy dependence could be observed within the error limits.
Hovestadt, D.↗
Simultaneous ELM suppression and divertor detachment via synergistic boron powder and neon injection in EAST
A novel approach for simultaneous power exhaust and edge-localized mode (ELM) control is presented in the Experimental Advanced Superconducting Tokamak discharges, which utilize an ITER-like tungsten divertor. Real-time injection of boron (B) powder and neon (Ne) gas overcomes their limitations encountered when used separately. Pure Ne seeding leads to a narrow operational window constrained by core impurity accumulation and H-mode to L-mode back transitions, while pure solid B injection (SBI) is insufficient for effective divertor cooling. In comparison, their combined use achieves a stable, stationary, ELM-suppressed H-mode with adequate power exhaust. This synergistic scenario features partial energy detachment at the outer divertor while maintaining good plasma confinement (H 98 ∼ 1) with minimal degradation. Two key features of this scenario are: (1) the SBI triggers a persistent Edge Harmonic Mode (EHM), which provides a crucial continuous particle transport channel, preventing Ne and tungsten/molybdenum accumulation without flushing out by ELM, and (2) the B + Ne mixture allows for active optimization of the radiated power profile. Core radiation can be reduced by substituting a portion of the Ne with B, leveraging their complementary non-coronal equilibrium radiation efficiencies. This combined B + Ne injection scheme presents a promising pathway toward integrated core-edge scenarios, offering the potential to minimize total impurity throughput while leveraging an actuator (powder injection) already being considered for ITER.
Boron↗
The effect of ICRH and NBI on tungsten transport in neon edge radiation cooled discharges in TEXTOR
Tungsten is planned to be the plasma-facing material for the main chamber and divertor in future devices like ITER, SPARC, and DTT. To address risks associated with tungsten, R&D is being carried out on various toroidal confinement devices. One particular research question is related to the optimum heating mix for ITER. To investigate the influence of the heating scheme on the release and transport of tungsten, a comparison of neutral beam injection (NBI) and ion cyclotron resonance frequency (ICRF) heating was carried out in TEXTOR tungsten test limiter experiments. The experiments were performed under standard L-mode conditions and in radiative improved-mode operation with neon seeding and boronized walls covering the graphite plasma-facing components. The plasma was heated with hydrogen or deuterium NBI alone or with deuterium NBI in combination with H-minority, ion cyclotron resonance heating. A movable solid tungsten limiter was inserted through a limiter lock system into the edge plasma. The impurity release from this limiter was evaluated from visible spectroscopy. The tungsten concentrations in the plasma core were determined by extreme ultraviolet spectroscopy and bolometry. With deuterium NBI alone, strong central radiation and accumulation of W was observed. This can, however, be avoided by adding ICRF heating.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Range and range rate system
A video controlled solid state range finding system which requires no radar, high power laser, or sophisticated laser target is disclosed. The effective range of the system is from 1 to about 200 ft. The system includes an opto-electric camera such as a lens CCD array device. A helium neon laser produces a source beam of coherent light which is applied to a beam splitter. The beam splitter applies a reference beam to the camera and produces an outgoing beam applied to a first angularly variable reflector which directs the outgoing beam to the distant object. An incoming beam is reflected from the object to a second angularly variable reflector which reflects the incoming beam to the opto-electric camera via the beam splitter. The first reflector and the second reflector are configured so that the distance travelled by the outgoing beam from the beam splitter and the first reflector is the same as the distance travelled by the incoming beam from the second reflector to the beam splitter. The reference beam produces a reference signal in the geometric center of the camera. The incoming beam produces an object signal at the camera.
Graham, Olin L.↗