SEARCH · Engineering Papers

Results for “solder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2021

Effect of Preconditioning on Post-Soldering Failures in Tantalum Capacitors

Soldering have a strong effect on performance and reliability of most surface mount technology components, including tantalum capacitors. High quality tantalum capacitors are likely the only type of components where soldering simulation is the first step during screening. Nevertheless, post-soldering failures of tantalum capacitors do happen and require additional analysis. Popcorning is a well-known effect in plastic encapsulated microcircuits (PEM) and it occurs also in chip tantalum capacitors. The sensitivity of parts to the presence of moisture during soldering is characterized by the moisture sensitivity level (MSL); however, contrary to PEMs, there is no standard procedure for establishing MSL for tantalum capacitors, and standard J-STD-020 is applicable partially only. In this work, the effect of absorbed moisture on soldering related degradation and failures in tantalum capacitors have been studied using 22 types of polymer and 11 types of MnO2 cathodes tantalum capacitors including single and multianode parts. The amount of moisture released during soldering has been estimated by measurements of mass and capacitance variations. Results show that moisture uptake in similar parts is approximately two times greater in polymer than in MnO2 capacitors. Cracking of the case and degradation of parameters can occur in both types of parts, but MnO2 capacitors are much more susceptible to catastrophic short circuit failures and their ignition is possible during the first power-on cycle. This type of failure in MnO2 capacitors is lot-related, can occur even at derated voltages and relatively low levels of moisture sorption corresponding to room conditions. Baking before soldering is an effective measure to prevent failures even in lots susceptible to popcorning damage. Recommendations for testing to establish MSL and for baking to reduce the probability of failures are suggested.

tantalum polymer capacitors↗

NASA NTRS1967

Investigation of Solder Cracking Problems on Printed Circuit Boards

A Solder Committee designated to investigate a solder cracking phenomena occurring on the SATURN electrical/electronic hardware found the cause to be induced stress in the soldered connections rather than faulty soldering techniques. The design of the printed circuit (PC) board assemblies did not allow for thermal expansion of the boards that occurred during normal operation. The difference between the thermal expansion properties of the boards and component lead materials caused stress and cracking in the soldered connections. The failure mechanism and various PC boards component mounting configurations are examined in this report. Effective rework techniques using flanged tubelets, copper tubelets, and soft copper wiring are detailed. Future design considerations to provide adequate strain relief in mounting configurations are included to ensure successful solder terminations.

CIRCUIT BOARD↗

NASA NTRS1976

Evaluation of advanced microelectronic fluxless solder-bump contacts for hybrid microcircuits

Technology for interconnecting monolithic integrated circuit chips with other components is investigated. The advantages and disadvantages of the current flip-chip approach as compared to other interconnection methods are outlined. A fluxless solder-bump contact technology is evaluated. Multiple solder-bump contacts were formed on silicon integrated circuit chips. The solder-bumps, comprised of a rigid nickel under layer and a compliant solder overlayer, were electroformed onto gold device pads with the aid of thick dry film photomasks. Different solder alloys and the use of conductive epoxy for bonding were explored. Fluxless solder-bump bond quality and reliability were evaluated by measuring the effects of centrifuge, thermal cycling, and high temperature storage on bond visual characteristics, bond electrical continuity, and bond shear tests. The applicability and suitability of this technology for hybrid microelectronic packaging is discussed.

Mandal, R. P.↗

NASA NTRS2008

Effects of hand soldering MIL-PRF 55365 tantalum capacitors

Different values of MIL-PRF-55365 tantalum capacitors were subjected to three different types of soldering conditions— Convection Reflow, JPL Standard Hand Soldering, and Optimized Hand Soldering. The electrical parameters for a large number of capacitors of each value were measured before and after thermal soldering stress. The results indicate that tantalum capacitors subjected to convection reflow conditions experience detectable changes in electrical parameters; capacitors subjected to hand solder conditions show reduced changes in electrical parameters when compared to the reflow samples. Optimized hand solder conditions are shown to have a minimal effect on electrical parameters.

Sheldon, Douglas↗

NASA NTRS1993

Thermal Cycling Fatigue in DIPs Mounted with Eutectic Tin-Lead Solder Joints in Stub and Gullwing Geometries

It has long been known that solder joints under mechanical stress are subject to failure. In early electronic systems, such failures were avoided primarily by avoiding the use of solder as a mechanical structural component. The rule was first to make sound wire connections that did not depend mechanically on solder, and only then to solder them. Careful design and miniaturization in modern electronic systems limits the mechanical stresses exerted on solder joints to values less than their yield points, and these joints have become integral parts of the mechanical structures. Unfortunately, while these joints are strong enough when new, they have proven vulnerable to fatigue failures as they age. Details of the fatigue process are poorly understood, making predictions of expected lifetimes difficult.

fatigue failure solder joints failure mechanisms s↗

NASA NTRS1993

Some Observations of Solder Joint Failure Under Tensile-Compressive Stress

It has long been known that solder joints under mechanical stress are subject to failure. In early electronic systems, such failures were avoided primarily by avoiding the use of solder as a mechanical structural component. The rule was to first make sound wire connections that did not depend mechanically on solder, and only then to solder them. Careful design and miniaturization in modern electronic systems limits the mechanical stresses exerted on solder joints to values less than their yield points, and these joints have become integral parts of the mechanical structures. Unfortunately, while these joints are strong enough when new, they have proven vulnerable to fatigue failures as they age.Details of the fatigue process are poorly understood, making predictions of expected lifetimes difficult.

solder joints fatigue failure thermal cycling test↗

NASA NTRS2013

A Study of Solder Alloy Ductility for Cryogenic Applications

For aerospace applications it is important to understand the mechanical performance of components at the extreme temperature conditions seen in service. For solder alloys used in microelectronics, cryogenic temperatures can prove problematic. At low temperatures Sn-based solders undergo a ductile to brittle transition that leads to brittle cracks, which can result in catastrophic failure of electronic components, assemblies and spacecraft payloads. As industrial processes begin to move away from Pb-Sn solder, it is even more critical to characterize the behavior of alternative Sn-based solders. Here we report on initial investigations using a modified Charpy test apparatus to characterize the ductile to brittle transformation temperature of nine different solder systems.

solders↗

NASA NTRS1985

Solder Bonding for Power Transistors

Indium solder boosts power rating and facilitates circuit changes. Efficient heat conduction from power transistor to heat sink provided by layer of indium solder. Low melting point of indium solder (141 degrees C) allows power transistor to be removed, if circuit must be reworked, without disturbing other components mounted with ordinary solder that melts at 181 degrees C. Solder allows devices operated at higher power levels than does conventional attachment by screws.

Snytsheuvel, H. A.↗

NASA NTRS1987

Ensuring Fully Soldered Through Holes

Simple differential-pressure soldering method provides visual evidence that hidden joints are fully soldered. Intended for soldering connector pins in plated through holes in circuit boards. Molten solder flows into plated through holes, drawn by vacuum in manifold over circuit board. Differential-pressure process ensures solder wets entire through hole around connector pin.

Blow, Raymond K.↗

NASA NTRS1992

Solder creep-fatigue interactions with flexible leaded parts

With flexible leaded parts, the solder-joint failure process involves a complex interplay of creep and fatigue mechanisms. To better understand the role of creep in typical multi-hour cyclic loading conditions, a specialized non-linear finite-element creep simulation computer program has been formulated. The numerical algorithm includes the complete part-lead-solder-PWB system, accounting for strain-rate dependence of creep on applied stress and temperature, and the role of the part-lead dimensions and flexibility that determine the total creep deflection (solder strain range) during stress relaxation. The computer program has been used to explore the effects of various solder creep-fatigue parameters such as lead height and stiffness, thermal-cycle test profile, and part/board differential thermal expansion properties. One of the most interesting findings is the strong presence of unidirectional creep-ratcheting that occurs during thermal cycling due to temperature dominated strain-rate effects. To corroborate the solder fatigue model predictions, a number of carefully controlled thermal-cycle tests have been conducted using special bimetallic test boards.

Ross, R. G., Jr.↗

NASA NTRS2002

Experimental Methods in Reduced-gravity Soldering Research

The National Center for Microgravity Research, NASA Glenn Research Center, and NASA Johnson Space Center are conducting an experimental program to explore the influence of reduced gravity environments on the soldering process. An improved understanding of the effects of the acceleration environment is important to application of soldering during current and future human space missions. Solder joint characteristics that are being considered include solder fillet geometry, porosity, and microstructural features. Both through-hole and surface mounted devices are being investigated. This paper focuses on the experimental methodology employed in this project and the results of macroscopic sample examination. The specific soldering process, sample configurations, materials, and equipment were selected to be consistent with those currently on-orbit. Other apparatus was incorporated to meet requirements imposed by operation onboard NASA's KC-135 research aircraft and instrumentation was provided to monitor both the atmospheric and acceleration environments. The contingent of test operators was selected to include both highly skilled technicians and less skilled individuals to provide a population cross-section that would be representative of the skill mix that might be encountered in space mission crews.

Pettegrew, Richard D.↗

NASA NTRS2011

Microwave Tissue Soldering for Immediate Wound Closure

A novel approach for the immediate sealing of traumatic wounds is under development. A portable microwave generator and handheld antenna are used to seal wounds, binding the edges of the wound together using a biodegradable protein sealant or solder. This method could be used for repairing wounds in emergency settings by restoring the wound surface to its original strength within minutes. This technique could also be utilized for surgical purposes involving solid visceral organs (i.e., liver, spleen, and kidney) that currently do not respond well to ordinary surgical procedures. A miniaturized microwave generator and a handheld antenna are used to deliver microwave energy to the protein solder, which is applied to the wound. The antenna can be of several alternative designs optimized for placement either in contact with or in proximity to the protein solder covering the wound. In either case, optimization of the design includes the matching of impedances to maximize the energy delivered to the protein solder and wound at a chosen frequency. For certain applications, an antenna could be designed that would emit power only when it is in direct contact with the wound. The optimum frequency or frequencies for a specific application would depend on the required depth of penetration of the microwave energy. In fact, a computational simulation for each specific application could be performed, which would then match the characteristics of the antenna with the protein solder and tissue to best effect wound closure. An additional area of interest with potential benefit that remains to be validated is whether microwave energy can effectively kill bacteria in and around the wound. Thus, this may be an efficient method for simultaneously sterilizing and closing wounds.

Arndt, G. Dickey↗

NASA NTRS2014

Effect of Preconditioning and Soldering on Failures of Chip Tantalum Capacitors

Soldering of molded case tantalum capacitors can result in damage to Ta205 dielectric and first turn-on failures due to thermo-mechanical stresses caused by CTE mismatch between materials used in the capacitors. It is also known that presence of moisture might cause damage to plastic cases due to the pop-corning effect. However, there are only scarce literature data on the effect of moisture content on the probability of post-soldering electrical failures. In this work, that is based on a case history, different groups of similar types of CWR tantalum capacitors from two lots were prepared for soldering by bake, moisture saturation, and longterm storage at room conditions. Results of the testing showed that both factors: initial quality of the lot, and preconditioning affect the probability of failures. Baking before soldering was shown to be effective to prevent failures even in lots susceptible to pop-corning damage. Mechanism of failures is discussed and recommendations for pre-soldering bake are suggested based on analysis of moisture characteristics of materials used in the capacitors' design.

multilayer ceramic capacitor (MLCC)↗

NASA NTRS1997

Inconsistencies in the Understanding of Solder Joint Reliability Physics

Over the years, many analytical and experimental research studies have aimed to improve the state-of-the-art assessment of solder joint integrity from a physics-of-failure perspective. Although much progress has been made, there still exist many inconsistent and even contradictory correlations and conclusions. Before discussing some of the prominent inconsistencies found in the literature, this paper reviews the fundamental physics underlying the nature of solder failure...Using the complex constitutive properties of solder, fundamental mechanical and thermomechanical proccesses can be modeled to demonstrate some of the inconsistencies in the literature.

solder joints solder solder joint failure joint fa↗

NASA NTRS1980

Stress-relieved solder joints

Mechanical stress on solder joints is reduced by procedure for soldering electronic components to circuit boards. Procedure was developed for radio-frequency (RF) strip-line circuits, for which dimensions must be carefully controlled to minimize parasitic capacitance and inductance. Procedure consists of loosening component from its mounting after each lead is soldered relieving induced stresses before next soldering step.

Zemenick, C. J.↗

NASA NTRS1990

Removing Dross From Molten Solder

Automatic device helps to assure good solder connections. Machine wipes dross away from area on surface of molten solder in pot. Sweeps across surface of molten solder somewhat in manner of windshield wiper. Each cycle of operation triggered by pulse from external robot. Equipment used wherever precise, automated soldering must be done to military specifications.

Webb, Winston S.↗

NASA NTRS1991

Inelastic Strain Analysis of Solder Joint in NASA Fatigue Specimen

The solder fatigue specimen designed by NASA-GSFC/UNISYS is analyzed in order to obtain the inelastic strain history during two different representative temperature cycles specified by UNISYS. In previous reports (dated July 25, 1990, and November 15, 1990), results were presented of the elastic-plastic and creep analysis for delta T = 31 C cycle, respectively. Subsequent results obtained during the current phase, from viscoplastic finite element analysis of the solder fatigue specimen for delta T = 113 C cycle are summarized. Some common information is repeated for self-completeness. Large-deformation continuum formulations in conjunction with a standard linear solid model is utilized for modeling the solder constitutive creep-plasticity behavior. Relevant material properties are obtained from the literature. Strain amplitudes, mean strains, and residual strains (as well as stresses) accumulated due to a representative complete temperature cycle are obtained as a result of this analysis. The partitioning between elastic strains, time-independent inelastic (plastic) strains, and time-dependent inelastic (creep) strains is also explicitly obtained for two representative cycles. Detailed plots are presented for two representative temperature cycles. This information forms an important input for fatigue damage models, when predicting the fatigue life of solder joints under thermal cycling

Dasgupta, Abhijit↗

NASA NTRS1992

Modified Spot Welder Solders Flat Cables

Soldering device, essentially modified spot welder, melts high-melting-temperature solders without damaging plastic insulation on flat electrical cables. Solder preform rests on exposed conductor of cable, under connector pin. Electrodes press pin/preform/conductor sandwich together and supply pulse of current to melt preform, bonding pin to conductor. Anvil acts as support and heat sink. Device used to solder flexible ribbon cables to subminiature pin connectors.

Haehner, Carl L.↗