Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “segmented blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

A prescribed wake rotor inflow and flow field prediction analysis, user's manual and technical approach

A user's manual is provided which includes the technical approach for the Prescribed Wake Rotor Inflow and Flow Field Prediction Analysis. The analysis is used to provide the rotor wake induced velocities at the rotor blades for use in blade airloads and response analyses and to provide induced velocities at arbitrary field points such as at a tail surface. This analysis calculates the distribution of rotor wake induced velocities based on a prescribed wake model. Section operating conditions are prescribed from blade motion and controls determined by a separate blade response analysis. The analysis represents each blade by a segmented lifting line, and the rotor wake by discrete segmented trailing vortex filaments. Blade loading and circulation distributions are calculated based on blade element strip theory including the local induced velocity predicted by the numerical integration of the Biot-Savart Law applied to the vortex wake model.

Egolf, T. A.↗
NASA NTRS1999

Successful Solutions to SSME/AT Development Turbine Blade Distress

As part of the High-Pressure Fuel Turbopump/Alternate Turbopump (HPFTP/AT) turbine blade development program, unique turbine blade design features were implemented to address 2nd stage turbine blade high cycle fatigue distress and improve turbine robustness. Features included the addition of platform featherseal dampers, asymmetric blade tip seal segments, gold plating of the blade attachments, and airfoil tip trailing edge modifications. Development testing shows these features have eliminated turbine blade high cycle fatigue distress and consequently these features are currently planned for incorporation to the flight configuration. Certification testing will begin in 1999. This presentation summarizes these features.

Montgomery, Stuart K.↗
NASA NTRS1986

Viscous compressible flow direct and inverse computation and illustrations

An algorithm for laminar and turbulent viscous compressible two dimensional flows is presented. For the application of precise boundary conditions over an arbitrary body surface, a body-fitted coordinate system is used in the physical plane. A thin-layer approximation of tne Navier-Stokes equations is introduced to keep the viscous terms relatively simple. The flow field computation is performed in the transformed plane. A factorized, implicit scheme is used to facilitate the computation. Sample calculations, for Couette flow, developing pipe flow, an isolated airflow, two dimensional compressor cascade flow, and segmental compressor blade design are presented. To a certain extent, the effective use of the direct solver depends on the user's skill in setting up the gridwork, the time step size and the choice of the artificial viscosity. The design feature of the algorithm, an iterative scheme to correct geometry for a specified surface pressure distribution, works well for subsonic flows. A more elaborate correction scheme is required in treating transonic flows where local shock waves may be involved.

Yang, T. T.↗
DOE OSTI2023

Aero‐servo‐elastic co‐optimization of large wind turbine blades with distributed aerodynamic control devices

Abstract This work introduces automated wind turbine optimization techniques based on full aero‐servo‐elastic models and investigates the potential of trailing edge flaps to reduce the levelized cost of energy (LCOE) of wind turbines. The Wind Energy with Integrated Servo‐control (WEIS) framework is improved to conduct the presented research. Novel methods for the generic implementation and tuning of trailing edge flap devices and their controller are also introduced. Primary flap and controller parameters are optimized to demonstrate potential maximum blade tip deflection reductions of 21 % . Concurrent design optimization (i.e., co‐design) of a novel segmented wind turbine blade with trailing edge flaps and its controller is then conducted to demonstrate blade cost savings of 5 % . Additionally, rotor diameter co‐design optimization is demonstrated to reduce the LCOE by 1.3 % without significant load increases to the tower. These results demonstrate the efficacy of control co‐design optimization using trailing edge flaps, and the entirety of this work provides a foundation for numerous control co‐design‐oriented studies for distributed aerodynamic control devices.

17 WIND ENERGY↗
NASA NTRS1991

Blade tip clearance control apparatus using bellcrank mechanism

A clearance control apparatus has a positioning mechanism for controlling clearance between rotor blade tips and a shroud segment of a gas turbine engine casing. The positioning mechanism is supported by the casing, coupled to the shroud segment, and actuatable for moving the shroud segment toward and away from the rotor blade tips to reach a position at which a desired clearance is established. The mechanism includes a shaft and a bellcrank actuating assembly. The shaft is mounted through a passage defined by a mounting structure on the casing for radial movement along a longitudinal axis of the shaft toward and away from the rotor axis and is coupled at its inner end to the shroud segment. The bellcrank actuating assembly is coupled to an outer end of the shaft and mounted to the casing adjacent the shaft for pivotal movement about an axis spaced from and extending transverse to the longitudinal axis of the shaft. The pivotal movement of the bellcrank actuating assembly produces radial movement of the shaft and shroud segment therewith toward and away from the rotor blade tips.

Corsmeier, Robert J.↗
NASA NTRS1982

System for slicing wafers

A newly patented process for slicing silicon wafers that has distinct advantages over methods now widely used is described. The primary advantage of the new system is that it allows the efficient slicing of a number of ingots simultaneously at high speed. The cutting action is performed mechanically, most often with diamond particles that are transported to the cutting zone by a fluid vehicle or have been made an integral part of the blade by plating or impregnation. The new system uses a multiple or ganged band saw, arranged and spaced so that each side, or length, segment of a blade element, or loop, provides a cutting function. Each blade is maintained precisely in position by guides as it enters and leaves each ingot. The cutting action is performed with a conventional abrasive slurry composed of diamond grit suspended in an oil- or water-based vehicle. The distribution system draws the slurry from the supply reservoir and pumps it to the injection tubes to supply it to each side of each ingot. A flush system is provided at the outer end of the work-station zone. In order to reduce potential damage, a pneumatically driven flushing fluid is provided.

Source record↗
DOE OSTI2021

Land-based wind turbines with flexible rail-transportable blades – Part 1: Conceptual design and aeroservoelastic performance

This work investigates the conceptual design and the aeroservoelastic performance of land-based wind turbines whose blades can be transported on rail via controlled bending. The turbines have a nameplate power of 5 MW and a rotor diameter of 206 m, and they aim to represent the next generation of land-based machines. Three upwind designs and two downwind designs are presented, combining different design goals together with conventional glass and pultruded carbon fiber laminates in the spar caps. One of the five blade designs is segmented and serves as a benchmark to the state of the art in industry. The results show that controlled flexing requires a reduction in the flapwise stiffness of the blades, but it represents a promising pathway for increasing the size of land-based wind turbine rotors. Given the required stiffness, the rotor can be designed either downwind with standard rotor preconing and nacelle uptilt angles or upwind with higher-than-usual angles. A downwind-specific controller is also presented, featuring a cut-out wind speed reduced to 19 m s –1 and a pitch-to-stall shutdown strategy to minimize blade tip deflections toward the tower. The flexible upwind and downwind rotor designs equipped with pultruded carbon fiber spar caps are found to generate the lowest levelized cost of energy, 2.9 % and 1.3 %, respectively, less than the segmented design. The paper concludes with several recommendations for future work in the area of large flexible wind turbine rotors.

17 WIND ENERGY↗
NASA NTRS1983

A refined finite element for vibration analysis of twisted blades based on beam theory

A finite element method of discretizing beam segments of pretwisted rotating blades is presented. Employing the matrix displacement method, stiffness and mass properties are developed from basic mechanics of a pretwisted beam theory. By introducing the proper displacement functions, the effect of rotor blade rotational motion on the stiffness matrix is obtained systematically from the kinetic energy expression. Comparing with other beam elements the derivation of this element is more fundamental. This allows one to apply the same approach to more complicated problems including nonlinear effects or complex dynamic motions. Illustrative examples are given comparing numerical results with available data and other numerical solutions from rotating and nonrotating force fields. These examples show that accurate prediction of vibration frequencies for pretwisted blades can be obtained by employing a quite modest number of degrees of freedom.

Sisto, F.↗
NASA NTRS1992

Vibration reduction in helicopter rotors using an active control surface located on the blade

A feasibility study of vibration reduction in a four-bladed helicopter rotor using individual blade control (IBC), which is implemented by an individually controlled aerodynamic surface located on each blade, is presented. For this exploratory study, a simple offset-hinged spring restrained model of the blade is used with fully coupled flap-lag-torsional dynamics for each blade. Deterministic controllers based on local and global system models are implemented to reduce 4/rev hub loads using both an actively controlled aerodynamic surface on each blade as well as conventional IBC, where the complete blade undergoes cyclic pitch change. The effectiveness of the two approaches for simultaneous reduction of the 4/rev hub shears and hub moments is compared. Conventional IBC requires considerably more power to achieve approximately the same level of vibration reduction as that obtained by implementing IBC using an active control surface located on the outboard segment of the blade. The effect of blade torsional flexibility on the vibration reduction effectiveness of the actively controlled surface was also considered and it was found that this parameter has a very substantial influence.

Millott, T. A.↗
NASA NTRS1987

High-Lift, Low-Pitching-Moment Airfoils

Two families of airfoil shapes improve rotor performance. Improvements enhance performances of helicopters and other rotorcraft but also applicable to aircraft propellers. Airfoil shapes best suited for inboard segment of rotor blade.

Noonan, Kevin W.↗
NASA NTRS1993

Rotorcraft noise: Status and recent developments

This paper briefly reviews rotorcraft noise mechanisms and their approximate importance for different types of rotorcraft in different flight regimes. Discrete noise is due to periodic flow disturbances and includes impulsive noise produced by phenomena which occur during a limited segment of a blade's rotation. Broadband noise results when rotors interact with random disturbances, such as turbulence, which can originate in a variety of sources. The status of analysis techniques for these mechanisms are reviewed. Also, some recent progress is presented on the understanding and analysis of tilt rotor aircraft noise due to: (1) recirculation and blockage effects of the rotor flow in hover; and (2) blade-vortex interactions in forward and descending flight.

George, Albert R.↗
NASA NTRS1991

Numerical simulation of shrouded propellers

A numerical model was developed for the evaluation of the performance characteristics of a shrouded propeller. Using this model, a computational study was carried out to investigate the feasibility of improving the aerodynamic performance of a propeller by encasing it in a shroud. The propeller blade was modeled by a segmented bound vortex positioned along the span of the blade at its quarter-chord-line. The shroud was modeled by a number of discrete vortex rings. Due to the mutual dependence of shroud and propeller vortex strengths and the propeller vortex wake an iterative scheme was employed. Three shroud configurations were considered: a cylindrical and two conical shrouds. The computed performance of the shrouded propeller was compared with that of a free propeller of identical propeller geometry. The numerical results indicated that the cylindrical shroud outperformed the conical shroud configurations for the cases considered. Furthermore, when compared to the free propeller performance, the cylindrical shroud showed a considerable performance enhancement over the free propeller. However, the improvements were found to decrease with an increase in the advance ratio and to virtually diminish at advance ratios of about 2.5.

Afjeh, Abdollah A.↗
NASA NTRS1990

Application of optimization methods to helicopter rotor blade design

A procedure for the minimum weight design of helicopter rotor blades with constraints on multiple coupled flap-lag natural frequencies, autorotational inertia, and centrifugal stress is presented. Optimum designs are obtained for blades with both rectangular and tapered planforms and are compared within a reference blade. The effects of higher-frequency constraints and stress constraints on the optimum blade designs are assessed. The results indicate that there is an increase in blade weight and a significant change in the design variable distributions with an increase in the number of frequency constraints. The inclusion of stress constraints has different effects on the wall thickness distributions of rectangular and tapered blades, but tends to increase the magnitude of the nonstructural segment weight distributions for both blade types.

Chattopadhyay, A.↗
NASA NTRS2007

Characteristics of Boundary Layer Transition in a Multi-Stage Low-Pressure Turbine

An experimental investigation of boundary layer transition in a multi-stage turbine has been completed using surface-mounted hot-film sensors. Tests were carried out using the two-stage Low Speed Research Turbine of the Aerodynamics Research Laboratory of GE Aircraft Engines. Blading in this facility models current, state-of-the-art low pressure turbine configurations. The instrumentation technique involved arrays of densely-packed hot-film sensors on the surfaces of second stage rotor and nozzle blades. The arrays were located at mid-span on both the suction and pressure surfaces. Boundary layer measurements were acquired over a complete range of relevant Reynolds numbers. Data acquisition capabilities provided means for detailed data interrogation in both time and frequency domains. Data indicate that significant regions of laminar and transitional boundary layer flow exist on the rotor and nozzle suction surfaces. Evidence of relaminarization both near the leading edge of the suction surface and along much of the pressure surface was observed. Measurements also reveal the nature of the turbulent bursts occuring within and between the wake segments convecting through the blade row. The complex character of boundary layer transition resulting from flow unsteadiness due to nozzle/nozzle, rotor/nozzle, and nozzle/rotor wake interactions are elucidated using these data. These measurements underscore the need to provide turbomachinery designers with models of boundary layer transition to facilitate accurate prediction of aerodynamic loss and heat transfer.

Wisler, Dave↗
NASA NTRS2004

Helping Aircraft Engines Lighten Up

High-temperature polyimide/carbon fiber matrix composites are developed by the Polymers Branch at NASA's Glenn Research Center. These materials can withstand high temperatures and have good processing properties, which make them particularly useful for jet and rocket engines and for components such as fan blades, bushings, and duct segments. Applying polyimide composites as components for aerospace structures can lead to substantial vehicle weight reductions. A typical polyimide composite is made up of layers of carbon or glass fibers glued together by a high-temperature polymer to make the material strong, stiff, and lightweight. Organic molecules containing carbon, nitrogen, oxygen, and hydrogen within the polyimide keep the material s density low, resulting in the light weight. The strength of a component or part made from a polyimide comes mainly from the reinforcing high-strength fibers. The strength of the carbon fibers coupled with the stiffness of polyimides allows engineers to make a very rigid structure without it being massive. Another benefit of a polyimide s suitability for aerospace applications is its reduced need for machining. When polyimide parts are removed from a mold, they are nearly in their final shape. Usually, very little machining is needed before a part is ready for use.

Source record↗
DOE OSTI2024

50 MW Segmented Ultralight Morphing Rotors for Wind Energy

A multi-institutional team designed a 50 Megawatt (MW) rated wind turbine featuring downwind aeroelastic morphing to reduce blade loads and allow an ultralight segmented rotor (mass reduction of about 25% compared to a conventional upwind rotor). The team used a control co-design approach with state-of-the art simulations including for the rotor and tower design using non-linear fluid-structure interactions and control algorithms, and the team also designed, built, and field-tested an aeroelastically-scaled downwind rotor to demonstrate this novel technology and validate the design tool fidelity. In a follow-on phase, these results were used along with an updated Levelized Cost Of Energy (LCOE) methodology to co-design a more detailed set of 25 MW rated turbine designs (including individual pitch control) based on minimum LCOE with highly flexible blades for an Atlantic Ocean offshore fixed-bottom design targeted towards market technology evaluation. A set of upwind and downwind designs at 25 MW rated scales were found to provide the best LCOE, with strong improvements over all previous offshore reference turbines (NREL 5MW, DTU 10 MW and IEA 15 MW). The optimized design would represent the world’s largest offshore turbine design, which combines several state-of-the-art structural, aerodynamic, and control technologies into a new and optimized system concept.

17 WIND ENERGY↗
NASA NTRS1974

Computer program for definition of transonic axial-flow compressor blade rows

A method is presented for designing axial-flow compressor blading from blade elements defined on cones which pass through the blade-edge streamline locations. Each blade-element centerline is composed of two segments which are tangent to each other. The centerline and surfaces of each segment have constant change of angle with path distance. The stacking line for the blade elements can be leaned in both the axial and tangential directions. The output of the computer program gives coordinates for fabrication and properties for aeroelastic analysis for planar blade sections. These coordinates and properties are obtained by interpolation across conical blade elements. The program is structured to be coupled with an aerodynamic design program.

Crouse, J. E.↗