Cryogenic Temperature Properties and Secondary Phase Characterization of CuCrZr Composites
Not provided.
Engineering↗
SEARCH · Engineering Papers
Results for “secondary phases”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Improving Ni-Based SOFC Anode Resilience and Durability through Secondary Phase Formation
The project used a multi-disciplinary approach to test test if 2° materials, added to traditional cermet components, enhanced SOFC mechanical strength, anode resilience and durability when subjected to electrochemical and environmental redox cycling. Findings from fracture testing, electrochemical studies and operando Raman spectroscopy measurements demonstrated that aluminum titanate (Al 2 TiO 5 or ALT) mechanically mixed with NiO-YSZ cermets confers superior mechanical strength and slower degradation rates under polarization. No deleterious effects from ALT in conversion efficiency were observed. Specific accomplishments included the following: (1) Refined methods used to fabricate ALT enhanced anodes into bi-layer anode supports to achieve high power densities; (2) Compared the effects of adding ALT mechanically to Ni-YSZ powders prior to anode fabrication with adding ALT through infiltration and co-infiltration of YSZ scaffolds; (3) Tested the resilience of these novel materials to electrochemical and environmental redox cycling and thermal stresses commonly encountered in functioning SOFCs; and (4) Characterized the ability of ALT to improve the carbon tolerance of Ni-YSZ anodes operating with dry methane.
01 COAL, LIGNITE, AND PEAT↗
Precipitation of Secondary Phases from the Dissolution of Silicate Glasses
Basaltic and anorthositic glasses were subjected to aqueous weathering conditions in the laboratory where the variables were pH, temperature, glass composition, solution composition, and time. Leached layers formed at the surfaces of glasses followed by the precipitation of X-ray amorphous iron and titanium oxides in acidic and neutral solutions at 25 C over time. Glass under oxidative hydrothermal treatments at 150 C yielded a three-layered surface; which included an outer smectite layer, a Fe-Ti oxide layer and an innermost thin leached layer. The introduction of Mg into solutions facilitated the formation of phyllosilicates. Aqueous hydrothermal treatment of anorthositic glasses (high Ca, low Ti) at 200 C readily formed smectite, whereas, the basaltic glasses (high Ti) were more resistant to alteration and smectite was not observed. Alkaline hydrothermal treatment at 2000e produced zeolites and smectites; only smectites formed at 200 C in neutral solutions. These mineralogical changes, although observed under controlled conditions, have direct applications in interpreting planetary (e.g., meteorite parent bodies) and terrestrial aqueous alteration processes.
Ming, Douglas W.↗
Potential Cement Phases in Sedimentary Rocks Drilled by Curiosity at Gale Crater, Mars
The Mars Science Laboratory rover Curiosity has encountered a variety of sedimentary rocks in Gale crater with different grain sizes, diagenetic features, sedimentary structures, and varying degrees of resistance to erosion. Curiosity has drilled three rocks to date and has analyzed the mineralogy, chemical composition, and textures of the samples with the science payload. The drilled rocks are the Sheepbed mudstone at Yellowknife Bay on the plains of Gale crater (John Klein and Cumberland targets), the Dillinger sandstone at the Kimberley on the plains of Gale crater (Windjana target), and a sedimentary unit in the Pahrump Hills in the lowermost rocks at the base of Mt. Sharp (Confidence Hills target). CheMin is the Xray diffractometer on Curiosity, and its data are used to identify and determine the abundance of mineral phases. Secondary phases can tell us about aqueous alteration processes and, thus, can help to elucidate past aqueous environments. Here, we present the secondary mineralogy of the rocks drilled to date as seen by CheMin and discuss past aqueous environments in Gale crater, the potential cementing agents in each rock, and how amorphous materials may play a role in cementing the sediments.
Rampe, E. B.↗
XRD and SEM/EDS characterization of two quaternary fuel alloys (U-2.5Mo-2.5Ti-5.0Zr and U-1.5Mo-1.5Ti-7.0Zr in wt. %) for fast reactors
The current study focuses on characterization of two potential fuel alloys for sodium-cooled fast reactors: U-2.5Mo-2.5Ti-5.0Zr (U-MT5Z) and U-1.5Mo-1.5Ti-7.0Zr (U-MT7Z) in wt. %. As-cast alloys and annealed (600°C, 500h) alloys are studied by X-ray powder diffraction (XRD) for their bulk structures, and scanning electron microscopy / energy dispersive X-Ray spectroscopy (SEM/EDS) for their microstructures and phase constituents. For as-cast alloys, the XRD results show that U-MT5Z mainly contains γ, while U-MT7Z alloy contains a. In both alloys, there are three phases indicated by EDS, a U-rich phase, secondary phase, and Zr-rich phase. Further, the elemental compositions varied in different phases and in different alloys. After annealing, both alloys exhibit the structures of α-U and U 2 Ti according to XRD. The EDS results suggest there are five phases found in both alloys.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Chemical Compensation Challenges in Processing Antiferroelectric PbZrO 3 Thin Films
The electric field-induced antipolar-to-polar phase transition in antiferroelectric materials is accompanied by large changes in the structural and functional response, making them attractive for many applications ranging from pulsed energy capacitors to high-strain-high (blocking-)force actuators, solid-state heating and cooling systems, and optoelectronic devices. PbZrO 3 , as an end member of the PZT, (x)PbZr 1–x Ti x O 3 , solid solution, has been the subject of many studies. However, processing of perovskite PbZrO 3 is extremely challenging due to phase instabilities induced by Pb loss at the temperatures necessary for perovskite crystallization. Here, we discuss the challenges associated with Pb loss, as well as its compensation through bulk Pb overstoichiometry and interfacial PbO additions, in chemical solution processed, highly oriented PbZrO 3 thin films. For both 042 o - and 001 o -oriented (o-orthorhombic distortion) PbZrO 3 thin films, the crystallization interfaces are the most important contributors to Pb loss and off-stoichiometric outcomes, and no single approach was sufficient to address these challenges. Pb-rich and Pb-deficient nonperovskite phases including ZrO x were only observable through microscopic characterization, and X-ray diffraction alone could not rule out the presence of such secondary phases. “Ideal” macroscopic antiferroelectric polarization-electric field double hysteresis curves were observed despite (at times) the large presence of secondary phases. However, reduced saturation polarization and increased phase transition electric fields were observed concomitantly with the presence of secondary phase(s) and tentatively assigned to the voltage drop across the ZrO x nanocrystals. Based on these results, it is imperative that the presence of secondary phases always be addressed (beyond X-ray diffraction spectra) in order to correctly evaluate the properties of antiferroelectric films.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
High-temperature deformation and microstructural analysis for Si3N4-Sc2O3
It was indicated that Si3N4 doped with Sc2O3 may exhibit high temperature mechanical properties superior to Si3N4 systems with various other oxide sintered additives. High temperature deformation of samples was studied by characterizing the microstructures before and after deformation. It was found that elements of the additive, such as Sc and O, exist in small amounts at very thin grain boundary layers and most of them stay in secondary phases at triple and multiple grain boundary junctions. These secondary phases are devitrified as crystalline Sc2Si2O7. Deformation of the samples was dominated by cavitational processes rather than movements of dislocations. Thus the excellent deformation resistance of the samples at high temperature can be attributed to the very small thickness of the grain boundary layers and the crystalline secondary phase.
Cheong, Deock-Soo↗
High-temperature deformation and microstructural analysis for silicon nitride-scandium(III) oxide
It was indicated that Si3N4 doped with Sc2O3 may exhibit high temperature mechanical properties superior to Si3N4 systems with various other oxide sintered additives. High temperature deformation of samples was studied by characterizing the microstructures before and after deformation. It was found that elements of the additive, such as Sc and O, exist in small amounts at very thin grain boundary layers and most of them stay in secondary phases at tripple and multiple grain boundary junctions. These secondary phases are devitrified as crystalline Sc2Si2O7. Deformation of the samples was dominated by cavitational processes rather than movements of dislocations. Thus the excellent deformation resistance of the samples at high temperature can be attributed to the very small thickness of the grain boundary layers and the crystalline secondary phase.
Cheong, Deock-Soo↗
The Effect of Film Composition on the Texture and Grain Size of CuInS2 Prepared by Spray Pyrolysis
Ternary single-source precursors were used to deposit CuInS2 thin films using chemical spray pyrolysis. We investigated the effect of the film composition on texture, secondary phase formation, and grain size. As-grown films were most often In-rich. They became more (204/220)-oriented as indium concentration increased, and always contained a yet unidentified secondary phase. The (112)-prefened orientation became more pronounced as the film composition became more Cu-rich. The secondary phase was determined to be an In-rich compound based on composition analysis and Raman spectroscopy. In addition, as-grown Cu-rich (112)-oriented films did not exhibit the In-rich compound. Depositing a thin Cu layer prior to the growth of CuInS2 increased the maximum grain size from - 0.5 micron to - 1 micron, and prevented the formation of the In-rich secondary phase.
Jin, Michael H.↗
CuInS2 Films Deposited by Aerosol-Assisted Chemical Vapor Deposition Using Ternary Single-Source Precursors
Polycrystalline CuInS2 films were deposited by aerosol-assisted chemical vapor deposition using both solid and liquid ternary single-source precursors (SSPs) which were prepared in-house. Films with either (112) or (204/220) preferred orientation, had a chalcopyrite structure, and (112)-oriented films contained more copper than (204/220)-oriented films. The preferred orientation of the film is likely related to the decomposition and reaction kinetics associated with the molecular structure of the precursors at the substrate. Interestingly, the (204/220)-oriented films were always In-rich and were accompanied by a secondary phase. From the results of post-growth annealing, etching experiments, and Raman spectroscopic data, the secondary phase was identified as an In-rich compound. On the contrary, (112)-oriented films were always obtained with a minimal amount of the secondary phase, and had a maximum grain size of about 0.5 micron. Electrical and optical properties of all the films grown were characterized. They all showed p-type conduction with an electrical resistivity between 0.1 and 30 Omega-cm, and an optical band gap of approximately 1.46 eV +/- 0.02, as deposited. The material properties of deposited films revealed this methodology of using SSPs for fabricating chalcopyrite-based solar cells to be highly promising.
Jin, Michael↗
Kinetics and Thermodynamics of Sr Permeation in CeO 2 -Based Barrier Layers for Solid-Oxide Electrolyzer Cells
Solid-oxide electrolyzer cells (SOECs) convert steam to hydrogen efficiently at high temperatures. However, during operation, the diffusion of cations or impurities through the cells due to electrode degradation can cause unwanted secondary phases to form, which may degrade device performance. Here, in this study, we use atomistic and mesoscale simulations coupled with experimental analysis to study the diffusion of Sr through the Gd-doped CeO 2 (GDC) barrier layer used to protect the yttria-stabilized zirconia (YSZ) electrolyte in SOECs. From our atomistic calculations, we find Sr diffusion to be negligibly slow in bulk GDC; however, surface diffusion is much more favorable. Subsequent mesoscale simulations show that Sr diffusion is activated when the porosity of GDC exceeds ∼10% and significantly exceeds diffusion in bulk and grain boundary regions. We also find that SrO-based species can accumulate at GDC surfaces; however, SrO aggregation and coarsening will be limited by the large lattice mismatch between GDC and SrO. Energy-dispersive X-ray spectroscopy (EDS) and electron diffraction confirm that Sr can accumulate within GDC pores and form disperse Sr-containing secondary phases. Altogether, Sr diffusion in dense GDC is unlikely to give rise to thick SrO layers, which would severely limit device performance. The formation of Sr-containing secondary phases can largely be avoided by restricting the porosity of the GDC layer as much as possible.
36 MATERIALS SCIENCE↗
Predicting zeolites’ stability during the corrosion of nuclear waste immobilization glasses: Comparison with glass corrosion experiments
During the long-term corrosion of nuclear waste glasses under nuclear waste disposal conditions, the precipitation of zeolitic phases has been linked to a delayed acceleration in glass corrosion (known as “Stage III”). Hence, predicting the thermodynamic propensity for zeolites to form upon the dissolution of nuclear waste glasses is key to ensure their long-term performance. Here, we compile a unified, internally-consistent thermodynamic database “clay20” to estimate the stability of clay and feldspar phases relevant to nuclear waste immobilization glasses, including beidellite(Mg, Ca, Na, K), kaolinite, montmorillonite(Mg, Ca, Na, K), nontronite(Mg, Ca, Na, K), saponite(Ca, Na, K), and albite. Based on this, we report a geochemical modeling method allowing us to predict the stability of secondary phases (including zeolites, calcium–silicate–hydrate gels, and clays) upon the dissolution of nuclear waste immobilization glasses. We show that this approach offers a realistic description of the stability of the secondary phases forming during the dissolution of two archetypical model nuclear glasses (namely, the International Simple Glass, ISG, and WVUTh-203) under conditions relevant to nuclear waste disposal (T = 90°C, p = 1 bar) as a function of pH. We find that the formation of silica and clay secondary phases is thermodynamically favored at low pH (pH < 10), whereas, in contrast, zeolite (analcime) and calcium–silicate–hydrate phases are favored at high pH (pH > 10.5). This suggests that thermodynamics (i.e., not solely kinetics) plays a key role in determining the range of solution pH wherein stage III corrosion may occur, i.e., when zeolite formation is favored.
Zhen-Wu, Bi Yun↗
Powder-metallurgy superalloy strengthened by a secondary gamma phase.
Description of experiments in which prealloyed powders of superalloy compositions were consolidated by extrusion after the strengthening by precipitation of a body-centered tetragonal gamma secondary Ni3 Ta phase. Thin foil electron microscopy showed that the mechanical properties of the resultant powder-metallurgy product were correlated with its microstructure. The product exhibited high strength at 1200 F without loss of ductility, after thermomechanical treatment and aging.
Kotval, P. S.↗
The Fundamental Creep Behavior Model of Gr.91 Alloy by ICME Approach (Final Report)
The current project mainly focused on the fundamental creep cracking mechanism of the Grade 91 system during the operation conditions in the advanced technologies FE power plants and build the link among Composition-Processing Parameters-Phase Stability-Microstructure-Creep Resistance. A model based on computational thermodynamics and diffusion kinetics will be developed to provide guidance on how to improve the creep resistance of the alloy system. The PI mainly investigate the Gr.91 base alloy and weldment with the Integrated Computational Materials Engineering (ICME) approach. The long-term goal of the proposed program is to develop a model for creep and fatigue resistant alloys with different elemental systems, compositions, and processing parameters of weldment and heat-treatment. In addition, new creep and fatigue resistant alloys are to be designed based on the predictions from the model. The computational as well as experimental results include three sections: 1) The compositional optimization and secondary phases evaluation regarding the creep resistance in Grade 91 steel through the CALPHAD approach. In this section, the formation of the critical secondary phases, M23C6, MX and Z-phase were well predicted based on many conditions like the temperature as well as compositions. Meanwhile, the role of different alloying elements was also considered as they will directly affect the formation of the secondary phases mentioned above based on the compositional evolution of the alloying elements. 2) An investigation of Creep Resistance in Grade 91 Steel through Computational Thermodynamics. We systematically considered the evolution of the four critical temperatures, Ac3, Ac1, the threshold of M23C6 and Z-phase, on basis of the computational approach. Meanwhile, the equilibrium cooling as well as Scheil simulations were also considered to perform further predictions based on the different cooling rates. 3) Creep lifetime and microstructural evolution of the Grade 91 steel. In this part, mainly experimental approach was performed on the real creep test from the beginning of the commercial Gr.91 alloys. The alloys were normalized, tempered, welded (Gleeble) and PWHT and finally subjected to the creep lifetime analyses. Finally, all the samples after each process were further characterized based on the OM, XRD and SEM technique to draw final conclusions.
01 COAL, LIGNITE, AND PEAT↗
Strontium Effects on the Formation of Iron-Intermetallic Phases in Secondary Al–9Si–0.6Fe Alloys
The presence and morphology of Fe-containing intermetallic phases affect the mechanical properties of aluminum alloys, especially in secondary Al–Si-based cast alloys. Although strontium (Sr) addition of 50 to 500 ppm is known to refine the needle-type eutectic silicon structure, the influence of Sr on the formation of Fe-intermetallic phases remains unclear. The present work investigates the combined additions of Sr and Mn to Al–9Si–0.6Fe–0.35Mg (All compositions are in wt pct except otherwise stated.) alloys on the formation of Fe-intermetallic phases at different solidification rates from ~ 1.5 to ~ 60 °C/s. Long and branched-type AlFeSi phase with size ranging from 50 to 120 µm are more common when solidified at the rate of 1.5 °C/s regardless of Sr and Mn additions. However, at the fast solidification rate of 60 °C/s, a 60 ppm Sr addition significantly reduced the average length of needle-shaped AlFeSi phase to less than 3 to 5 µm. Thermodynamic simulations have been performed using CALculation of PHAse Diagrams (CALPHAD) models to predict the formation of various phases and their possible interactions during solidification. The results indicated that the combination of a high solidification rate and about 60 ppm of Sr is beneficial to refining the δ-Al 3 FeSi 2 phase in Al–Si–Mg alloys containing 0.6 pctFe. As a result, this unexpected finding of Fe-intermetallic refinement by low Sr addition (~60 ppm) provides an important guide in designing secondary alloys for sustainable casting applications.
36 MATERIALS SCIENCE↗
Thermal Conductivity and Erosion Durability of Composite Two-Phase Air Plasma Sprayed Thermal Barrier Coatings
To enhance efficiency of gas turbines, new thermal barrier coatings (TBCs) must be designed which improve upon the thermal stability limit of 7 wt% yttria stabilized zirconia (7YSZ), approximately 1200 C. This tenant has led to the development of new TBC materials and microstructures capable of improved high temperature performance. This study focused on increasing the erosion durability of cubic zirconia based TBCs, traditionally less durable than the metastable t' zirconia based TBCs. Composite TBC microstructures composed of a low thermal conductivity/high temperature stable cubic Low-k matrix phase and a durable t' Low-k secondary phase were deposited via APS. Monolithic coatings composed of cubic Low-k and t' Low-k were also deposited, in addition to a 7YSZ benchmark. The thermal conductivity and erosion durability were then measured and it was found that both of the Low-k materials have significantly reduced thermal conductivities, with monolithic t' Low-k and cubic Low-k improving upon 7YSZ by approximately 13 and approximately 25%, respectively. The 40 wt% t' Low-k composite (40 wt% t' Low-k - 60 wt% cubic Low-k) showed a approximately 22% reduction in thermal conductivity over 7YSZ, indicating even at high levels, the t' Low-k secondary phase had a minimal impact on thermal in the composite coating. It was observed that a mere 20 wt% t' Low-k phase addition can reduce the erosion of a cubic Low-k matrix phase composite coating by over 37%. Various mixing rules were then investigated to assess this non-linear composite behavior and suggestions were made to further improve erosion durability.
Rare earth zirconia↗
Particle Size Distribution Dynamics Can Help Constrain the Phase State of Secondary Organic Aerosol
Particle phase state is a property of atmospheric aerosols that has important implications for the formation, evolution, and gas/particle partitioning of secondary organic aerosol (SOA). In this work, we use a size-resolved chemistry and microphysics model (SOM-TOMAS), updated to include an explicit treatment of particle phase state, to constrain the bulk diffusion coefficient (Db) of SOA produced from ??- pinene ozonolysis. By leveraging data from laboratory experiments performed in the absence of a seed and under dry conditions, we find that the Db for SOA can be constrained (1-7 ×10-15 cm2 s-1 in these experiments) by simultaneously reproducing the time-varying SOA mass concentrations and the evolution of the particle size distribution. Another version of our model that used the predicted SOA composition to calculate the glass transition temperature, viscosity, and, ultimately, Db (~10-15 cm2 s-1) of the SOA was able to reproduce the mass and size distribution measurements when we included oligomer formation (oligomers accounted for about a fifth of the SOA mass). Our work highlights the potential of a size resolved SOA model to constrain the particle phase state of SOA by utilizing historical measurements of the evolution of the particle size distribution.
He, Yicong↗