Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pv cost”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Silicon-sheet and thin-film cell and module technology potential: Issue study

The development of high-efficiency low-cost crystalline silicon ribbon and thih-film solar cells for the energy national photovoltaics program was examined. The findings of an issue study conducted are presented. The collected data identified the status of the technology, future research needs, and problems experienced. The potentials of present research activities to meet the Federal/industry long-term technical goal of achieving 15 cents per kilowatt-hour levelized PV energy cost are assessed. Recommendations for future research needs related to crystalline silicon ribbon and thin-film technologies for flat-plate collectors are also included.

Shimada, K.↗
DOE OSTI2024

Solar Design/Install Labor Quantification (Cooperative Research and Development Final Report)

The goals of this project were to quantify the rate and/or total expected labor expenditure of engineers designing solar arrays and electricians installing solar across a spectrum of project sizes and configurations. Specifically, procuring and analyzing labor data from solar engineering firms relating to the amount of time it takes an engineer to design a solar project, the amount of time it takes an engineer to perform a wiring or stringing design, the amount of time it takes an electrician to install a solar project and the amount of time it takes electricians to install the strings of a solar array. Then these details could be analyzed to evaluate labor intensity for solar design/installation. These goals were unable to be completed because the participant was unable to collect the necessary data for analysis.

14 SOLAR ENERGY↗
NASA NTRS1979

A photovoltaic power system in the remote African village of Tangaye, Upper Volta

A photovoltaic (PV) system powering a grain mill and a water pump was installed in the remote West African village of Tangaye, Upper Volta. Village characteristics as well as system design, hardware, installation and operation to date are described. The PV system cost is discussed. A baseline socio-economic study performed and a follow-up study is planned to determine the impact of the system on the villagers.

Bifano, W. J.↗
NASA NTRS1997

Electrochemical Characterization of Semiconductor Materials and Structures

For a period covering October 1, 1995 through August 12, 1996, the research group at CSU has conducted theoretical and experimental research on "Electrochemical Characterization of Semiconductor Materials and Structures. " The objective of this investigation was to demonstrate the applicability of electrochemical techniques for characterization of complex device structures based on InP and GaAs, Ge, InGaAs, InSb, InAs and InSb, including: (1) accurate EC-V net majority carrier concentration depth profiling, and (2) surface and bulk structural and electrical type defect densities. Our motivation for this R&D effort was as follows: "Advanced space solar cells and ThermoPhotoVoltaic (TPV) cells are fabricated using a large variety of III-V materials based on InP and GaAs for solar cells and low bandgap materials such as Ge, InGaAs, InAs and InSb for TPV applications. At the present time for complex device structures using these materials, however, there is no simple way to assess the quality of these structures prior to device fabrication. Therefore, process optimization is a very time consuming and a costly endeavor". Completion of this R&D effort would have had unquestionable benefits for space solar cell and TPV cells, since electrochemical characterization of the above cell structures, if properly designed can provide many useful structural and electrical material information virtually at any depth inside various layers and at the interfaces. This, could have been applied for step-by-step process optimization, which could have been used for fabrication of new generation high efficiency, low cost space PV and TPV cells.

Source record↗
NASA NTRS1991

Flexible copper-indium-diselenide films and devices for space applications

With the ever increasing demands on space power systems, it is imperative that low cost, lightweight, reliable photovoltaics be developed. One avenue of pursuit for future space power applications is the use of low cost, lightweight flexible PV cells and arrays. Most work in this area assumes the use of flexible amorphous silicon (a-Si), despite its inherent instability and low efficiencies. However, polycrystalline thin film PV such as copper-indium-diselenide (CIS) are inherently more stable and exhibit better performance than a-Si. Furthermore, preliminary data indicate that CIS also offers exciting properties with respect to space applications. However, CIS has only heretofore only produced on rigid substrates. The implications of flexible CIS upon present and future space power platforms was explored. Results indicate that space qualified CIS can dramatically reduce the cost of PV, and in most cases, can be substituted for silicon (Si) based on end-of-life (EOL) estimations. Furthermore, where cost is a prime consideration, CIS can become cost effective than gallium arsenide (GaAs) in some applications. Second, investigations into thin film deposition on flexible substrates were made, and data from these tests indicate that fabrication of flexible CIS devices is feasible. Finally, data is also presented on preliminary TCO/CdS/CuInSe2/Mo devices.

Armstrong, J. H.↗
NASA NTRS1983

Economic implications of current systems

The primary goals of this study are to estimate the value of R&D to photovoltaic (PV) metallization systems cost, and to provide a method for selecting an optimal metallization method for any given PV system. The value-added cost and relative electrical performance of 25 state-of-the-art (SOA) and advanced metallization system techniques are compared.

Daniel, R. E.↗
DOE OSTI2026

Economic Incentives for Agrivoltaics Systems with Commodity Crops in the Midwestern United States

Declining costs of photovoltaic (PV) technology and rising market and policy incentives are leading to the growing deployment of PV on cropland in the US Midwest, leading to concerns about the displacement of food and feed crop production. Agrivoltaic (AV) technology enables the dual use of land by co-locating PV energy and crop production, potentially reducing land-use competition with crop production. We develop a benefit-cost analysis framework to compare the net economic returns from AV to those with stand-alone PV and crop production on a representative field and show conditions under which AV can be more profitable for both a solar developer and a farmer. We integrate it with a crop and solar energy model to simulate the performance of various field designs and space and height configurations in AV systems to accommodate soybean production with conventional farm equipment under representative conditions in the US Midwest. We find that an AV system with soybean production is less profitable than PV alone for a solar developer due to the high capital costs of raising panel height, and less profitable for a farmer than leasing land for PV due to its adverse effects of shading on crop yield. We discuss the changes in technology and market prices of solar energy and soybeans that are necessary to make the AV system profitable for solar developers and farmers. We show that AV can worsen rather than mitigate the conflict between food crops and solar energy production in the Midwest.

14 SOLAR ENERGY↗
DOE OSTI2025

Techno-economic implications and cost of forecasting errors in solar PV power production using optimized deep learning models

Accurate solar Photovoltaic (PV) power forecasting is important for enhancing both the performance and economic feasibility of PV systems. This study evaluates several deep learning models, including Dense Neural Networks (DNN), Long Short-Term Memory (LSTM), Convolutional Neural Networks (CNN), and a hybrid LSTMCNN model, for predicting PV power production one day in advance. Prior to optimization, the models exhibited relatively high errors, with the best model (DNN) achieving a Root Mean Square Error (RMSE) of 31.13 kW and a coefficient of determination (R 2 ) of 62.15 %. After employing Bayesian optimization, the LSTM-CNN model demonstrated the best performance, with the RMSE reduced to 9.79 kW and R 2 improved to 97.62 %, showcasing significant enhancement in predictive accuracy. Here, the economic evaluation considered three cases: rewards for underestimation (0.08 USD/kWh), no rewards, and penalties for both over-and underestimation (120 % of the utility tariff). In the rewards scenario, the LSTM-CNN model reduced the Levelized Cost of Electricity (LCOE) by 4 %, while in the penalty scenario, a backup diesel generator would have increased the LCOE by 49 %. Additionally, the LSTM-CNN model minimized financial losses, achieving the lowest penalties and maximizing net cash flow compared to other models, demonstrating its overall technical and economic superiority.

Deep learning↗
DOE OSTI2026

Annual Supply Chain for Photovoltaics (ASC-PV) in the United States: 2024 in Review

This report analyzes U.S. PV and BESS supply chains and costs in 2024, for PV module and battery technologies, structural and electrical balance of system (BOS) components, as well as PV recycling. The report concludes with an analysis of technology installation trends, government support for domestic manufacturing, manufacturing jobs, and the domestic content of PV systems installed in the United States in 2024.

14 SOLAR ENERGY↗
NASA NTRS2000

SAVANT: Solar Array Verification and Analysis Tool Demonstrated

The photovoltaics (PV) industry is now being held to strict specifications, such as end-oflife power requirements, that force them to overengineer their products to avoid contractual penalties. Such overengineering has been the only reliable way to meet such specifications. Unfortunately, it also results in a more costly process than is probably necessary. In our conversations with the PV industry, the issue of cost has been raised again and again. Consequently, the Photovoltaics and Space Environment Effects branch at the NASA Glenn Research Center at Lewis Field has been developing a software tool to address this problem. SAVANT, Glenn's tool for solar array verification and analysis is in the technology demonstration phase. Ongoing work has proven that more efficient and less costly PV designs should be possible by using SAVANT to predict the on-orbit life-cycle performance. The ultimate goal of the SAVANT project is to provide a user-friendly computer tool to predict PV on-orbit life-cycle performance. This should greatly simplify the tasks of scaling and designing the PV power component of any given flight or mission. By being able to predict how a particular PV article will perform, designers will be able to balance mission power requirements (both beginning-of-life and end-of-life) with survivability concerns such as power degradation due to radiation and/or contamination. Recent comparisons with actual flight data from the Photovoltaic Array Space Power Plus Diagnostics (PASP Plus) mission validate this approach.

Chock, Ricaurte↗
NASA NTRS1994

PV Technology for Low Intensity, Low Temperature (LILT) Applications

As a result of the recent NASA emphasis on smaller, lower cost space missions, PV is now being considered for a number of missions operating at solar distances of 3 AU or greater. In the past, many of these missions would utilize an RTG (radioisotope thermoelectric generator). Historically, silicon solar cell behavior at these distances has been compromised by a number of mechanisms including shunting, nonohmic back contacts, and the 'broken knee' curve shape. The former two can usually be neglected for modern silicon cells, but the latter has not been eliminated. This problem has been identified with localized diffusion at the top contact/silicon interface which leads to structural changes at the local junction. This is believed to create a resistive metal-semiconductor-like (MSL) interface in parallel with the junction which results in the characteristic forms of the LILT (low intensity, low temperature) 'broken knee'. This paper discusses a TaSiN contact barrier that will prevent the MSL structure in the junction.

spacecraft power LILT low temperature low intensit↗
NASA NTRS1994

(abstract) PV Technology for Low Intensity, Low Temperature (LILT) Applications

As a result of the recent NASA emphasis on smaller, lower cost space missions, PV is now being considered for a number of missions operating at solar distances of 3 AU or greater. In the past, many of these missions would utilize an RTG (radioisotope thermoelectric generator). Historically, silicon solar cell behavior at these distances has been compromised by a number of mechanisms including shunting, nonohmic back contacts, and the 'broken knee' curve shape. The former two can usually be neglected for modern silicon cells, but the latter has not been eliminated. This problem has been identified with localized diffusion at the top contact/silicon interface which leads to structural changes at the local junction. This is believed to create a resistive metal-semiconductor-like (MSL) interface in parallel with the junction which results in the characteristic forms of the LILT (low intensity, low temperature) 'broken knee'. This paper discusses a TaSiN contact barrier that will prevent the MSL structure in the junction.

spacecraft power LILT low temperature low intensit↗
NASA NTRS2011

Grid-Tied Photovoltaic Power System

A grid-tied photovoltaic (PV) power system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility. Operating costs of a PV power system are low compared to conventional power technologies. This method can displace the highest-cost electricity during times of peak demand in most climatic regions, and thus reduce grid loading. Net metering is often used, in which independent power producers such as PV power systems are connected to the utility grid via the customers main service panels and meters. When the PV power system is generating more power than required at that location, the excess power is provided to the utility grid. The customer pays the net of the power purchased when the on-site power demand is greater than the onsite power production, and the excess power is returned to the utility grid. Power generated by the PV system reduces utility demand, and the surplus power aids the community. Modern PV panels are readily available, reliable, efficient, and economical, with a life expectancy of at least 25 years. Modern electronics have been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy equal to the modern PV panels. The grid-tied PV power system was successfully designed and developed, and this served to validate the basic principles developed, and the theoretical work that was performed. Grid-tied PV power systems are reliable, maintenance- free, long-life power systems, and are of significant value to NASA and the community. Of particular value are the analytical tools and capabilities that have been successfully developed. Performance predictions can be made confidently for grid-tied PV systems of various scales. The work was done under the NASA Hybrid Power Management (HPM) Program, which is the integration of diverse power devices in an optimal configuration for space and terrestrial applications.

Eichenberg, Dennis J.↗
NASA NTRS1985

Practical aspects of photovoltaic technology, applications and cost (revised)

The purpose of this text is to provide the reader with the background, understanding, and computational tools needed to master the practical aspects of photovoltaic (PV) technology, application, and cost. The focus is on stand-alone, silicon solar cell, flat-plate systems in the range of 1 to 25 kWh/day output. Technology topics covered include operation and performance of each of the major system components (e.g., modules, array, battery, regulators, controls, and instrumentation), safety, installation, operation and maintenance, and electrical loads. Application experience and trends are presented. Indices of electrical service performance - reliability, availability, and voltage control - are discussed, and the known service performance of central station electric grid, diesel-generator, and PV stand-alone systems are compared. PV system sizing methods are reviewed and compared, and a procedure for rapid sizing is described and illustrated by the use of several sample cases. The rapid sizing procedure yields an array and battery size that corresponds to a minimum cost system for a given load requirement, insulation condition, and desired level of service performance. PV system capital cost and levelized energy cost are derived as functions of service performance and insulation. Estimates of future trends in PV system costs are made.

Rosenblum, L.↗
NASA NTRS2007

Lightweight, Flexible Solar Cells on Stainless Steel Foil and Polymer for Space and Stratospheric Applications

The availability of low-cost, lightweight and reliable photovoltaic (PV) modules is an important component in reducing the cost of satellites and spacecraft. In addition, future high-power spacecraft will require lightweight PV arrays with reduced stowage volume. In terms of the requirements for low mass, reduced stowage volume, and the harsh space environment, thin film amorphous silicon (a-Si) alloy cells have several advantages over other material technologies (1). The deposition process is relatively simple, inexpensive, and applicable to large area, lightweight, flexible substrates. The temperature coefficient has been found to be between -0.2 and -0.3 %/degC for high-efficiency triple-junction a-Si alloy cells, which is superior for high temperature operation compared to crystalline Si and triple-junction GaAs/InGaP/Ge devices at 0.53 %/degC and 0.45 %/degC, respectively (2). As a result, the reduction in efficiency at high temperature typical in space conditions is less for a-Si alloy cells than for their crystalline counterparts. Additionally, the a-Si alloy cells are relatively insensitive to electron and proton bombardment. We have shown that defects that are created by electrons with energies between 0.2 to 2 MeV with fluence up to 1x10(exp 15) e/sq cm and by protons with energy in the range 0.3 MeV to 5 MeV with fluence up to 1x10(exp 13) p/sq cm can be annealed out at 70 C in less than 50 hours (1). Further, modules incorporating United Solar s a-Si alloy cells have been tested on the MIR space station for 19 months with only minimal degradation (3). For stratospheric applications, such as the high altitude airship, the required PV arrays are typically of considerably higher power than current space arrays. Airships typically have a large area available for the PV, but weight is of critical importance. As a result, low cost and high specific power (W/kg) are key factors for airship PV arrays. Again, thin-film a-Si alloy solar cell technology is well suited to such applications.

Beernink, Kevin↗
NASA NTRS1996

Status of multijunction solar cells

This paper describes Applied Solar's present activity on Multijunction (MJ) space cells. We have worked on a variety of MJ cells, both monolithic and mechanically stacked. In recent years, most effort has been directed to GaInP2/GaAs monolithic cells, grown on Ge substrates, and the status of this cell design will be reviewed here. MJ cells are in demand to provide satellite power because of the acceptance of the overwhelming importance of high efficiency to reduce the area, weight and cost of space PV power systems. The need for high efficiencies has already accelerated the production of GaAs/Ge cells, with efficiencies 18.5-19%. When users realized that MJ cells could provide higher efficiencies (from 22% to 26%) with only fractional increase in costs, the demand for production MJ cells increased rapidly. The main purpose of the work described is to transfer the MOCVD growth technology of MJ high efficiency cells to a production environment, providing all the space requirements of users.

Yeh, Y. C. M.↗
NASA NTRS1982

Intermediate power conditioners - Where are we now?

It has been recognized in the photovoltaic (PV) industry that even in the event of a dramatic reduction in the price of generating PV cells, the costs for the other components of the system represent still a major obstacle towards commercialization. A project was, therefore, initiated with the aim to develop baseline and conceptual power conditioner designs which would attempt to meet a specified set of cost and performance goals in the 30 to 200 kW (Intermediate) size. Resulting Intermediate Size Power Conditioner Studies led to a number of conclusions. There is a need for a set of guidelines or standards for utility interconnection. The advent of new devices with more power handling capability will change the desired topology.

Klein, J. W.↗