Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗

A Review: Microstructural and Phase Evolution in Alloys during Extended Plastic Deformation

Materials in service and during processing are often subjected to plastic deformation. For multi-phase metallic alloys, simple geometric models and atomistic simulations suggest that two distinctive regimes in these materials’ evolution during deformation exist. At low strains, evolutions are often dominated by the kinetic roughening of interfaces, which results from the superdiffusive transport of matter in sheared crystals. Furthermore, at high strains and temperatures where thermal diffusion is sluggish, on the other hand, shearing- induced forced atomic mixing dominates these evolutions, resulting in significantly enhanced solubility. Distinguishing these two regimes is shown to provide a convenient framework for rationalizing and analyzing recent experiments and simulations on wear of layered structures in the low strain-regime and nonequilibrium phase co-existence and self-organization in highly immiscible or reactive alloy systems in the high-strain regime.

36 MATERIALS SCIENCE↗

Room temperature corrosion behaviour of plastically deformed AISI 304 stainless steel by friction stir welding in neutral and acidified chloride solutions

Severe plastic deformation of 304L stainless steel plate was carried out by friction stirring under an isothermal tool temperature at 825°C. The friction stirred zone showed extensive grain refinement, high fraction of low angle grain boundaries due to dislocation rearrangement, Σ3 and Σ9 special grain boundaries and discrete Fe–Cr–Mn-rich particles. Electrochemical polarisation measurements were done on the base metal (BM) and friction stir welded (FSW) specimens in the neutral and acidified 3.5% NaCl solutions. The BM showed marginally better pitting resistance in the neutral chloride solution than the FSW because of a larger fraction of special grain boundaries, and larger grain size. Whereas in acidified 3.5% NaCl solution, the FSW showed better corrosion resistance than the BM. Furthermore, the surface film of the FSW had a lower impedance and a lower defect concentration than the BM indicating higher diffusivity of point defects in the FSW.

36 MATERIALS SCIENCE↗

A spatially-resolved model of neutron-irradiated tungsten coupling stochastic cluster dynamics and finite deformation plasticity

Structural materials used in nuclear reactors face severe degradation in mechanical properties, such as hardening and embrittlement. At the microscopic scale, this occurs due to creation and accumulation of irradiation-induced defects and their interaction with system dislocations. Although techniques exist which can model evolution of irradiation defects, for instance kinetic transport theory-based models, their interaction with mechanical deformation of the bulk material has not been investigated extensively. In this work, we demonstrate a novel spatially-resolved multiscale coupling between microscopic irradiation defect evolution, modeled using Stochastic Cluster Dynamics (SCD) and macroscopic mechanical deformation modeled using a finite-deformation plasticity model. SCD is used to determine the statistically averaged defect cluster spacing, dependent on operating conditions such as irradiation dose and temperature. This acts as an initial condition that governs the critical resolved shear stress of dislocation glide in the macroscopic plasticity model. This framework is used to predict mechanical behavior in post-mortem test of irradiated Tungsten samples, which has found its importance as structural material used in nuclear reactors. The results obtained using the coupled approach are in good agreement with experimental data of uniaxial tension tests. The model is able to capture the effect of temperature and irradiation dose on the material hardening. Two methods are proposed to estimate hardness – using Tabor's Law relating uniaxial yield stress to hardness and from flat-punch simulations. The results are in reasonable agreement with hardness data from micro-indentation experiments of irradiated Tungsten samples. Finally, the model is also able to reveal microstructural details such as spatial variation in defect density and local stress.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Assessment of diffuse-interface methods for compressible multiphase fluid flows and elastic-plastic deformation in solids

This work describes three diffuse-interface methods for the simulation of immiscible, compressible multiphase fluid flows and elastic-plastic deformation in solids. The first method is the localized-artificial-diffusivity approach of Cook, Subramaniam et al., and Adler and Lele, in which artificial diffusion terms are added to the individual phase mass fraction transport equations and are coupled with the other conservation equations. The second method is the gradient-form approach that is based on the quasi-conservative method of Shukla et al., in which the diffusion and sharpening terms (together called regularization terms) are added to the individual phase volume fraction transport equations and are coupled with the other conservation equations. The third approach is the divergence-form approach that is based on the fully conservative method of Jain et al., in which the regularization terms are added to the individual phase volume fraction transport equations and are coupled with the other conservation equations. In the present study, all three diffuse-interface methods are used in conjunction with a four-equation, multicomponent mixture model, in which pressure and temperature equilibria are assumed among the various phases. The primary objective of this work is to compare these three methods in terms of their ability to: maintain constant interface thickness throughout the simulation; conserve mass, momentum, and energy; and maintain accurate interface shape for long-time integration. The second objective of this work is to consistently extend these methods to model interfaces between solid materials with strength. To assess and compare the methods, they are used to simulate a wide variety of problems, including (1) advection of an air bubble in water, (2) shock interaction with a helium bubble in air, (3) shock interaction and the collapse of an air bubble in water, and (4) Richtmyer–Meshkov instability of a copper–aluminum interface. The current work focuses on comparing these methods in the limit of relatively coarse grid resolution, which illustrates the true performance of these methods. In conclusion, this is because it is rarely practical to use hundreds of grid points to resolve a single bubble or drop in large-scale simulations of engineering interest.

97 MATHEMATICS AND COMPUTING↗

Half-hard copper PTW model parameters for plastic deformation calibrated to strain rates from 10 −3 -10 7 /s

This document demonstrates a calibration of the Preston-Tonks-Wallace (PTW) model of plastic deformation that fairly accurately reproduces the flow stress of half-hard copper across strain rates varying by a factor of more than ten billion. The experiments included are quasistatic compression at low rates, Split Hopkinson Pressure Bar (SHPB) compression at intermediate rates, and arrested Richtmyer-Meshkov instability (RMI) growth at high strain rates. The temperatures vary from liquid nitrogen (77 K) to around 500 K. The largest true strains obtained are approximately 0.5. It would be interesting to compare the results to copper deformation data at higher pressures and higher strains.

36 MATERIALS SCIENCE↗

Effect of free surfaces on localized plastic deformation in single-crystal nickel containing helium bubbles and radiation-induced self-interstitial atom clusters

This paper presents molecular dynamics (MD) simulations of plastic deformation in single-crystal Ni models containing internal distributions of helium (He) bubbles and self-interstitial atom (SIA) clusters corresponding to experimental characterization of ex-service Inconel X-750 components. Here, we simulate single crystals with and without free surfaces at room temperature and 588K, the latter temperature corresponding to the Inconel X-750 service conditions. Both models are deformed under multiple slip to a maximum deviatoric strain of ~10 %. A dislocation slip band forms in the model without free surfaces, but not in the model with free surfaces. However, the latter exhibits nano-twin nucleation from surfaces. Helium (He) bubbles that overlap with a slip band or a nano-twinned region deform more severely than other bubbles in the model. Nevertheless, the bubbles do not link up and do not form configurations that resemble incipient cracks.

36 MATERIALS SCIENCE↗

Microstructural Engineering of Cu-Rich Nanoprecipitate formation in NiCoFeCrCu0.12 High-Entropy Alloy via Severe Plastic Deformation for Enhanced Irradiation Tolerance

This study demonstrates a defect-engineering approach for controlling Cu-rich precipitates in FeNiCrCoCu0.2 high-entropy alloys (Cu-HEAs), delivering a novel pathway for next-generation nuclear reactor materials with superior irradiation resistance. This work establishes that severe plastic deformation (SPD) processing via Shear Assisted Processing and Extrusion (ShAPE) and Friction Stir Layer Deposition (FSLD) creates dense dislocation networks and subgrain boundaries that fundamentally alter precipitation behavior under identical thermal treatments. Atom probe tomography (APT) indicates that SPD produces a metastable, atomically homogeneous solid solution that, upon moderate heat treatment (500°C/10 hour), develops remarkedly stronger Cu clustering than the as-cast counterpart. High-temperature exposure (800°C/100 h) produces near-pure Cu precipitates (~90 at% Cu) with significantly enhanced defect-sink efficacy in SPD-processed alloys: precipitate sizes of 50-60 nm and number densities of 2.7-3.8 × 10¹7 m?³, compared to 89 nm and 0.44 × 10¹7 m?³ in as-cast materials. Collectively, the findings establish defect-mediated precipitation control as a scalable, high-impact route to tailor sink density and distribution in HEAs, enabling microstructures optimized for irradiation tolerance and mechanical robustness in nuclear reactor environments.

Meher, Subhashish↗

Textured Electrodes: Manipulating Built-In Crystallographic Heterogeneity of Metal Electrodes via Severe Plastic Deformation

Control of crystallography of metal electrodeposit films has recently emerged as a key to achieving long operating lifetimes in next-generation batteries. It is reported that the large crystallographic heterogeneity, e.g., broad orientational distribution, that appears characteristic of commercial metal foils, results in rough morphology upon plating/stripping. On this basis, an accumulative roll bonding (ARB) methodology—a severe plastic deformation process—is developed. Zn metal is used as a first example to interrogate the concept. It is demonstrated that the ARB process is highly effective in achieving uniform crystallographic control on macroscopic materials. After the ARB process, the Zn grains exhibit a strong (002) texture (i.e., [002] Zn //ND). The texture transitions from a classical bipolar pattern to a nonclassical unipolar pattern under large nominal strain eliminate the orientational heterogeneity of the foil. The strongly (002)-textured Zn remarkably improves the plating/stripping performance by nearly two orders of magnitude under practical conditions. The performance improvements are readily scaled to achieve pouch-type full batteries that deliver exceptional reversibility. The ARB process can, in principle, be applied to any metal chemistry to achieve similar crystallographic uniformity, provided the appropriate temperature and accumulated strains are employed. Here this concept is evaluated using commercial Li and Na foils, which, unlike Zn (HCP), are BCC crystals. The simple process for creating strong textures in both hexagonal and cubic metals and illustrating the critical role such built-in crystallography plays underscores opportunities for developing highly reversible thin metal anodes (e.g., hexagonal Zn, Mg, and cubic Li, Na, Ca, Al).

36 MATERIALS SCIENCE↗

Atomistic Study of the Plastic Deformation of Transition Metals and High Entropy Alloys (Final Report)

The overarching goal of the research performed in the studies supported by the DOE Basic Energy Sciences has been investigation of mechanical properties of materials employed in technologies related to energy production and conversion using atomic level computer modeling. The materials studied are body-centered-cubic (BCC) transition metals, including α-iron, their alloys and most recently also compositionally complex, so called high entropy alloys (HEAs), which are believed to become future materials in high temperature applications. The goal of the research has been to achieve atomic level understanding of the deformation and fracture of these materials starting from the electronic structure, coarse grain the material energetics into potentials describing interaction between atoms and proceed via atomistic modeling and mesoscopic models to investigation of the glide of dislocations and thus advance the theory of plastic deformation of studied materials.

36 MATERIALS SCIENCE↗

Comparison of cracking behavior of nanocrystalline Cu film on substrates of different plastic deformation mechanisms

Nanocrystalline (NC) metallic thin films on metal substrates usually undergo substantial cracking at applied strains of a few percent due to strain concentration at the film/substrate interfaces. In this work, we show that the cracking of a nanocrystalline Cu film can be significantly inhibited by a NiTi substrate. NC Cu films are deposited on 304 stainless steel, Kapton and NiTi substrates, in which plastic deformation occurs via dislocation slip, molecule chain disentanglement and collective lattice shear, respectively. NC Cu film on NiTi substrate starts to show observable cracks at an applied strain of 24%, in contrast to 6% for that on steel and 15% for that on Kapton. Further, the crack density in the film on NiTi substrate is two to three orders lower than the counterparts. The discrepancy is suggested to attribute to the reduced local strain concentration enabled by the uniform lattice shear and high strain hardening of the NiTi substrate.

36 MATERIALS SCIENCE↗

Concentration dependent properties and plastic deformation facilitate instability of the solid-electrolyte interphase in Li-ion batteries

Lithium-ion batteries (LIBs) often suffer from capacity fading and poor cyclic performance due to mechanical degradation of the solid-electrolyte interphase (SEI). Here we perform numerical simulations and theoretical analysis to elucidate the role of plasticity in wrinkling and ratcheting behaviors of an SEI/electrode system. A coupled diffusion and finite deformation framework is formulated and numerically implemented as a user-element subroutine (UEL) to describe transient lithium diffusion and accompanying elastic–viscoplastic deformation of the electrode. It is found that concentration dependent properties and plastic deformation facilitate wrinkling in such a system. A wrinkled morphology may further lead to ratcheting and related failure under cycling. A phase diagram of four types of cyclic behaviorsis identified in terms of the charging rate and time. Our analysis suggests several potential strategies to avoid wrinkling and ratcheting instabilities, such as charging/discharging the electrode at a sufficiently slow rate, and/or introducing a thick artificial SEI with a pre-tension.

25 ENERGY STORAGE↗

Global and local texture development during initial plastic deformation of cold-pilgered Zircaloy-4 tubing

In this work we present a thorough characterization of the texture development during the initial step of a cold pilgering process of a Zircaloy-4 TREX tube, on which the axial cross section is reduced by 80% over a 40cm length with an overall Q-ratio of 2.34, followed by a recrystallization thermal treatment. Texture across a tapered specimen representing this working zone was characterized by neutron diffraction and high energy synchrotron x-ray diffraction at 28 positions (4 locations along its length and 7 locations across its thickness with 0.3 mm spatial resolution), and on the deformed end after the thermal treatment. Results show that the starting material (TREX tube) presents a texture gradient through its wall thickness, with the c poles aligned to the hoop direction at the outer surface (with radial and hoop Kearns factors: f R =0.36, f H = 0.50), and gradually rotating around the axial direction to become a quasi-radial orientation (~35 o out of the radial direction) at the inner surface ( f R =0.43, f H =0.35). The overall texture becomes more radial due to the cold pilgering, but the texture gradient remains during the whole deformation process, being always more radial at the inner surface, ( f R =0.53, f H =0.37 at 80%) than at the outer surface ( f R =0.41, f H =0.50at 80%). The most remarkable changes in texture produced by the rolling process is a 30 o rotation of the grains around their c-axis, producing a marked increase of the <11 2 ¯ 0> // axial fiber texture at expenses of the original <10 1 ¯ 0> // axial fiber texture observed in the TREX tube. The observed changes in texture during deformation were correctly explained by visco-plastic self-consistent (VPSC) modelling. This was achieved after the inclusion of the basal <a> slip system, which plays a central role to explain the 30 o rotation around the c-axis during deformation. The texture evolution was correctly described after the inclusion of a drag effect to grain rotation due to the interaction with neighbouring grains. The through thickness texture differences are greatly reduced by the recrystallization thermal treatment, with similar Kearns factors at the inner surface ( f R =0.50, f H =0.28) and the outer surface ( f R =0.48, f H =0.39). The predominance of the <10 1 ¯ 0> // axial fiber texture is recovered after recrystallization.

36 MATERIALS SCIENCE↗

Impact of the plastic deformation microstructure in metals on the kinetics of recrystallization: A phase-field study

The sensitivity of recrystallization kinetics in metals to the heterogeneity of microstructure and deformation history is a widely accepted experimental fact. However, most of the available recrystallization models employ either a mean field approach or use grain-averaged parameters, and thus neglecting the mesoscopic heterogeneity induced by prior deformation. Here in the present study, we investigate the impact of deformation-induced dislocation (subgrain) structure on the kinetics of recrystallization in metals using the phase-field approach. The primary focus here is upon the role of dislocation cell boundaries. The free energy formulation of the phase-field model accounts for the heterogeneity of the microstructure by assigning localized energy to the resulting dislocation microstructure realizations generated from experimental data. These microstructure realizations are created using the universal scaling laws for the spacing and the misorientation angles of both the geometrically necessary and incidental dislocation boundaries. The resulting free energy is used into an Allen-Cahn based model of recrystallization kinetics, which are solved using the finite element method. The solutions thus obtained shed light on the critical role of the spatial heterogeneity of deformation in the non-smooth growth of recrystallization nuclei and on the final grain structure. The results showed that, in agreement with experiment, the morphology of recrystallization front exhibits protrusions and retrusions. By resolving the subgrain structure, the presented algorithm paves the way for developing predictive kinetic models that fully account for the deformed state of recrystallizing metals.

36 MATERIALS SCIENCE↗

Atomistic Investigation of Plastic Deformation and Dislocation Motion in Uranium Mononitride

Uranium mononitride (UN) is a promising advanced nuclear fuel due to its high thermal conductivity and high fissile density. However, many aspects of its mechanical behavior, particularly at reactor-relevant conditions, remain unclear. In this study, molecular dynamics (MD) simulations were employed to investigate the deformation behavior and dislocation motion in UN. We found that the Kocevski potential predicts the principal slip system as $\frac{1}{2}$ $\langle110\rangle${110}, aligning with experimental data. On the other hand, the Tseplyaev potential predicts slip to primarily occur on $\frac{1}{2}$ $\langle110\rangle${111}. MD simulations of stress–strain behavior were used to estimate the nanoindentation hardness, revealing that the Kocevski potential accurately predicts hardness even though it fails to model dynamic plasticity. Complete dislocation mobility functions have been fitted for the edge and screw dislocations in both the thermally activated and phonon-drag regimes. The 300 K linear mobility of the edge dislocation using the Tseplyaev potential was found to be 817 Pa -1 ·s -1 , whereas that of the screw dislocation using the Kocevski potential was found to be 4546 Pa -1 ·s -1 . At intermediate stresses, we observed that the subsonic steady-state motion of the edge dislocation in UN is intermittently interrupted by velocity jumps, reaching the average sound velocity. Finally, the threshold Schmid stress is calculated as 179–197 MPa, which gives an upper-limit estimate of the uniaxial yield stress of polycrystalline UN of 548–603 MPa. These findings, including the fitted dislocation mobility function, provide essential input for future plasticity and dislocation dynamics models of nuclear fuels.

36 MATERIALS SCIENCE↗

Unlocking Electrostrain in Plastically Deformed Barium Titanate

Achieving substantial electrostrain alongside a large effective piezoelectric strain coefficient (d 33 *) in piezoelectric materials remains a formidable challenge for advanced actuator applications. Here, in this work, a straightforward approach to enhance these properties by strategically designing the domain structure and controlling the domain switching through the introduction of arrays of ordered {100}<100> dislocations is proposed. This dislocation engineering yields an intrinsic lock-in steady–state electrostrain of 0.69% at a low field of 10 kV cm -1 without external stress and an output strain energy density of 5.24 J cm -3 in single-crystal BaTiO 3 , outperforming the benchmark piezoceramics and relaxor ferroelectric single-crystals. Additionally, applying a compression stress of 6 MPa fully unlocks electrostrains exceeding 1%, yielding a remarkable d 33 * value over 10 000 pm V -1 and achieving a record-high strain energy density of 11.67 J cm -3 . Optical and transmission electron microscopy, paired with laboratory and synchrotron X-ray diffraction, is employed to rationalize the observed electrostrain. Phase-field simulations further elucidate the impact of charged dislocations on domain nucleation and domain switching. These findings present an effective and sustainable strategy for developing high-performance, lead-free piezoelectric materials without the need for additional chemical elements, offering immense potential for actuator technologies.

36 MATERIALS SCIENCE↗

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗

Uncovering the phonon spectra and lattice dynamics of plastically deformable InSe van der Waals crystals

Stacking two-dimensional (2D) van der Waals (vdW) materials in a layered bulk structure provides an appealing platform for the emergence of exotic physical properties. As a vdW crystal with exceptional plasticity, InSe offers the opportunity to explore various effects arising from the coupling of its peculiar mechanical behaviors and other physical properties. Here, we employ neutron scattering techniques to investigate the correlations of plastic interlayer slip, lattice anharmonicity, and thermal transport in InSe crystals. Not only are the interlayer slip direction and magnitude well captured by shifts in the Bragg reflections, but we also observe a deviation from the expected Debye behaviour in the heat capacity and lattice thermal conductivity. Combining the experimental data with first-principles calculations, we tentatively attribute the observed evidence of strong phonon-phonon interactions to a combination of a large acoustic-optical frequency resonance and a nesting effect. These findings correlate the macroscopic plastic slip and the microscopic lattice dynamics, providing insights into the mechano-thermo coupling and modulation in 2D vdW materials.

36 MATERIALS SCIENCE↗