Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parametric study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

A parametric study of the copper chloride laser

A parametric study of the double-pulsed copper chloride laser is reported. The effects of a wide range of variables on the laser energy density and on three characteristic time intervals (the minimum, maximum, and optimum delay time) between the two electrical-discharge pulses were studied. The geometric variables investigated included a tube diameter of 2.3 to 40 mm and a tube length of 3 to 60 cm. Three buffer gases, helium, neon, and argon, were studied over the pressure range 0.5-50 torr, and the tube temperature was varied from 270 to 500 C. The energy density and voltage of both the dissociation and pumping pulse were varied independently from less than 1 mJ/cu cm at 8.5 kV to over 500 mJ/cu cm at 20 kV. The optimum conditions for maximum laser energy density were found to be with 20 torr neon in a 10-mm by 30-cm tube at 400 C. The maximum energy density obtained was 22 microjoules/cu cm.

Nerheim, N. M.↗
NASA NTRS1993

A parametric study of harmonic rotor hub loads

A parametric study of vibratory rotor hub loads in a nonrotating system is presented. The study is based on a CAMRAD/JA model constructed for the GBH (Growth Version of Blackhawk Helicopter) Mach-scaled wind tunnel rotor model with high blade twist (-16 deg). The theoretical hub load predictions are validated by correlation with available measured data. Effects of various blade aeroelastic design changes on the harmonic nonrotating frame hub loads at both low and high forward flight speeds are investigated. The study aims to illustrate some of the physical mechanisms for change in the harmonic rotor hub loads due to blade design variations.

He, Chengjian↗
DOE OSTI2023

Parametric Study of 239 Pu and 235 U Mass Equivalency in Spherical Geometries

In this technical document, parametric studies were performed to determine if a bounding mass equivalency can be used to simplify multi-material models in MCNP6 for criticality evaluations. The studies explored the simplification of MCNP6 models by substituting materials, particularly 239 Pu for 235 U. The initial hypothesis for the material simplification is based on the subcritical mass limits from the ANSI/ANS- 8.1 standard which states that for water reflected metal spheres the limits are 20.1 kg 235 U and 5.0 kg 239 Pu. Using those masses, it was hypothesized that a 20.1 kg sphere of 235 U and a 5.0 kg sphere of 239 Pu could be considered to have the same multiplication. Given that equivalency, 4kg 235 U could be modeled by 1kg 239 Pu (i.e., a mass ratio of 4:1). The parametric studies compare the materials 239 Pu and 235 U independently and in multi-material spherical models. Critical mass, critical thickness, critical mass ratio and critical thickness ratio values are presented as functions of inner radius. keff values are presented as a function of inner radius at different mass ratios and total masses. Results indicate that the conservative bounding mass equivalency is one. That is, if substituting 239 Pu for 235 U it should be done on a gram for gram basis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1991

Aerodynamic parametric studies and sensitivity analysis for rotor blades in axial flight

The analytical capability is offered for aerodynamic parametric studies and sensitivity analyses of rotary wings in axial flight by using a 3D undistorted wake model in curved lifting line theory. The governing equations are solved by both the Multhopp Interpolation technique and the Vortex Lattice method. The singularity from the bound vortices is eliminated through the Hadamard's finite part concept. Good numerical agreement between both analytical methods and finite differences methods are found. Parametric studies were made to assess the effects of several shape variables on aerodynamic loads. It is found, e.g., that a rotor blade with out-of-plane and inplane curvature can theoretically increase lift in the inboard and outboard regions respectively without introducing an additional induced drag.

Chiu, Y. D.↗
NASA NTRSDate not supplied

Parametric Study of Federated Conflict Resolution for UAM Operations

This work presents a federated conflict resolution algorithm and its parametric study for UAM operations. A federated speed-control-based conflict resolution algorithm is introduced first, including its rules of the road, data exchange requirement, and critical parameters. Two experiments were set up for the parametric study. The first investigates five parameters: look ahead time, resolution update interval, maximum allowed speed reduction, traffic flow interval, and crossing angle. The second experiment studies the uncertainty of departure time. Metrics associated with safety, efficiency, and conflict resolution effort were measured for each scenario. A Design Of Experiment (DOE) analysis was used to perform the multi-factor analysis for the first experiment. It revealed that the crossing angle and flow interval were the most critical parameters across all three metrics, followed by maximum allowed speed reduction. Look ahead time and resolution update interval were of minor significance to safety and conflict resolution effort, but had little to no effect on efficiency. The analysis of the second experiment showed that, given a flow rate, the fluctuation in departure time was absorbed by the conflict resolution algorithm, which resulted in a relatively small fluctuation in airborne delay.

Urban air mobility↗
NASA NTRS2016

A Model for Straight and Helical Solar Jets: II. Parametric Study of the Plasma Beta

Context. Jets are dynamic, impulsive, well-collimated plasma events that develop at many different scales and in different layers of the solar atmosphere. Aims. Jets are believed to be induced by magnetic reconnection, a process central to many astrophysical phenomena. Within the solar atmosphere, jet-like events develop in many different environments, e.g. in the vicinity of active regions as well as in coronal holes, and at various scales, from small photospheric spicules to large coronal jets. In all these events, signatures of helical structure and/or twisting/rotating motions are regularly observed. The present study aims to establish that a single model can generally reproduce the observed properties of these jet-like events. Methods. In this study, using our state-of-the-art numerical solver ARMS, we present a parametric study of a numerical tridimensional magnetohydrodynamic (MHD) model of solar jet-like events. Within the MHD paradigm, we study the impact of varying the atmospheric plasma beta on the generation and properties of solar-like jets. Results. The parametric study validates our model of jets for plasma beta ranging from 10(sup 3) to 1, typical of the different layers and magnetic environments of the solar atmosphere. Our model of jets can robustly explain the generation of helical solar jet-like events at various beta less than or equal to 1. We show that the plasma beta modifies the morphology of the helical jet, explaining the different observed shapes of jets at different scales and in different layers of the solar atmosphere. Conclusions. Our results allow us to understand the energisation, triggering, and driving processes of jet-like events. Our model allows us to make predictions of the impulsiveness and energetics of jets as determined by the surrounding environment, as well as the morphological properties of the resulting jets.

Magnetic Field↗
NASA NTRS2014

Trigger of Standard and Blowout Solar Jets: I. Parametric Studies of the Magnetic Field Geometry

Context. Jets are dynamic, impulsive, well collimated plasma events developing at many different scales and in differentlayers of the solar atmosphere.Aims. Jets are believed to be induced by magnetic reconnection a process central to many astrophysical phenomena.Studying their dynamics can help us to better understand the processes acting in larger eruptive events (e.g. flares andcoronal mass ejection) as well as mass, magnetic helicity and energy transfer at all scale in the solar atmosphere. Therelative simplicity of their magnetic geometry and topology, compared with larger solar active events, makes jets idealcandidate for studying the fundamental role of reconnection in energetic events. Methods. In this study, using our state-of-the-art numerical solver ARMS, we present several parametric studies of anumerical three-dimensional magneto-hydrodynamic model of solar jet-like events. We study the impact of the magneticfield inclination and photospheric field distribution on the generation and properties of two types of observed solar jets:the so-called standard and blowout jets.Results. The present parametric studies validate our model of jets for different geometric properties of the magneticconfiguration. On one hand, a blowout jets is eventually always trigger for the range of parameters that we tested. The3D magnetic null-point configuration is a very robust structure for the energy storage and impulsive release characteristicof blowout jets. On the other hand, the existence of the standard jet depends on the magnetic geometry. We show thatthe reconnection occurring during the standard jet phase influences the properties of the trigger of the blowout jet.Conclusions. Our results allow us to better understand the energization, triggering and driving processes of standardand blowout jets. Our model allows us to predict the impulsiveness and energetics of jets in terms of the surroundingmagnetic field configuration. Finally we discuss the interpretation of standard jets and blowout jets and the physicalfactors that determine which type of jets will occur.

Pariat, E.↗
NASA NTRSDate not supplied

Parametric Study of Federated Conflict Resolution for UAM Operations using DOE Analysis

This work presents a federated conflict resolution algorithm and its parametric study for UAM operations. A federated speed-control-based conflict resolution algorithm is introduced first, including its rules of the road, data exchange requirement, and critical parameters. Two experiments were set up for the parametric study. The first investigates five parameters: look ahead time, resolution update interval, maximum allowed speed reduction, traffic flow interval, and crossing angle. The second experiment studies the uncertainty of departure time. Metrics associated with safety, efficiency, and conflict resolution effort were measured for each scenario. A Design Of Experiment (DOE) analysis was used to perform the multi-factor analysis for the first experiment. It revealed that the crossing angle and flow interval were the most critical parameters across all three metrics, followed by maximum allowed speed reduction. Look ahead time and resolution update interval were of minor significance to safety and conflict resolution effort, but had little to no effect on efficiency. The analysis of the second experiment showed that, given a flow rate, the fluctuation in departure time was absorbed by the conflict resolution algorithm, which resulted in a relatively small fluctuation in airborne delay.

Urban air mobility↗
NASA NTRS1995

Computation of noise radiation from turbofans: A parametric study

This report presents the results of a parametric study of the turbofan far-field noise radiation using a finite element technique. Several turbofan noise radiation characteristics of both the inlet and the aft ducts have been examined through the finite element solutions. The predicted far-field principal lobe angle variations with duct Mach number and cut-off ratio compare very well with the available analytical results. The solutions also show that the far-field lobe angle is only a function of cut-off ratio, and nearly independent of the mode number. These results indicate that the finite element codes are well suited for the prediction of noise radiation characteristics of a turbofan. The effects of variations in the aft duct geometry are examined. The ability of the codes to handle ducts with acoustic treatments is also demonstrated.

Nallasamy, M.↗
DOE OSTI2022

Parametric study of high-energy ring-shaped electron beams from a laser wakefield accelerator

Abstract Laser wakefield accelerators commonly produce on-axis, low-divergence, high-energy electron beams. However, a high charge, annular shaped beam can be trapped outside the bubble and accelerated to high energies. Here we present a parametric study on the production of low-energy-spread, ultra-relativistic electron ring beams in a two-stage gas cell. Ring-shaped beams with energies higher than 750 MeV are observed simultaneously with on axis, continuously injected electrons. Often multiple ring shaped beams with different energies are produced and parametric studies to control the generation and properties of these structures were conducted. Particle tracking and particle-in-cell simulations are used to determine properties of these beams and investigate how they are formed and trapped outside the bubble by the wake produced by on-axis injected electrons. These unusual femtosecond duration, high-charge, high-energy, ring electron beams may find use in beam driven plasma wakefield accelerators and radiation sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2003

Software for Managing Parametric Studies

The Information Power Grid Virtual Laboratory (ILab) is a Practical Extraction and Reporting Language (PERL) graphical-user-interface computer program that generates shell scripts to facilitate parametric studies performed on the Grid. (The Grid denotes a worldwide network of supercomputers used for scientific and engineering computations involving data sets too large to fit on desktop computers.) Heretofore, parametric studies on the Grid have been impeded by the need to create control language scripts and edit input data files painstaking tasks that are necessary for managing multiple jobs on multiple computers. ILab reflects an object-oriented approach to automation of these tasks: All data and operations are organized into packages in order to accelerate development and debugging. A container or document object in ILab, called an experiment, contains all the information (data and file paths) necessary to define a complex series of repeated, sequenced, and/or branching processes. For convenience and to enable reuse, this object is serialized to and from disk storage. At run time, the current ILab experiment is used to generate required input files and shell scripts, create directories, copy data files, and then both initiate and monitor the execution of all computational processes.

Yarrow, Maurice↗
DOE OSTI2022

Numerical modeling and parametric study of a dual purpose underground thermal battery

We report integrating thermal energy storage with building energy systems can enable flexible building electric demands at buildings to help mitigate the mismatch between electricity supply and demand. A novel building heating and cooling system that integrates a dual-source heat pump with hybrid thermal storage named dual-purpose underground thermal battery (DPUTB) has been developed for reshaping building electric demands. The proposed DPUTB integrated geothermal heat pump system is an original innovation that enables Grid-interactive Energy Efficient buildings. This paper focuses on the study of the novel DPUTB. The DPUTB works as both a thermal storage tank (an inner tank) and a ground heat exchanger (an outer tank separated from the inner tank by the insulation material). High fidelity and computationally effective models are needed to predict the performance of the novel DPUTB. This study has developed a simplified dynamic model for the DPUTB according to heat transfer and energy conservation principles and validated it by using experimental data obtained from testing a small-scale DPUTB apparatus. A parametric study was conducted to identify a design that can achieve the target thermal storage performance of load shift and energy efficiency. The parametric study results show that the inner tank shell thermal conductivity and the phase change material's melting point are the two most influencing factors on the performance of the DPUTB. One single full-size DPUTB with the identified design could provide 1-ton cooling (3.51 kW) with the supply temperature lower than 11 °C for 4 hours in summer after being fully charged in 8 hours. The inner tank filled with phase change material is for cooling thermal storage as a latent tank in the design. However, its capacity can be as high as 60 MJ as a sensible water tank for heating storage in winter. In the future study, the DPUTB model will be incorporated into the dual-source heat pump system for evaluating the overall system performance of demand side management in the long term.

25 ENERGY STORAGE↗
NASA NTRS2001

Parametric Study of a YAV-8B Harrier in Ground Effect Using Time-Dependent Navier-Stokes Computations

Flow simulations using the time-dependent Navier-Stokes equations remain a challenge for several reasons. Principal among them are the difficulty to accurately model complex flows, and the time needed to perform the computations. A parametric study of such complex problems is not considered practical due to the large cost associated with computing many time-dependent solutions. The computation time for each solution must be reduced in order to make a parametric study possible. With successful reduction of computation time, the issue of accuracy, and appropriateness of turbulence models will become more tractable.

Shishir, Pandya↗
NASA NTRS1976

Parametric study of predictor accuracy impact on OFT rendezvous targeting

A parametric study was made to quantitatively define the effects of errors in the state vector predictor used by the Operational Flight Trainer (OFT) rendezvous targeting algorithms. The effect of the predictor accuracy on the OFT rendezvous profile is shown by the sensitivity of various critical rendezvous parameters with respect to downrange and radial predictor error rates. The effect of both inertial (same errors on both vehicles) and relative (differential errors on one vehicle with respect to the other) errors were considered. Relative radial error rates had the largest impact on the rendezvous followed by relative downrange errors, radial inertial errors and downrange inertial errors.

Glenn, S. W.↗
NASA NTRS1981

A parametric study of staged fuel injector configurations for scramjet applications

A parametric study of staged (multiple) perpendicular fuel injector configurations has been conducted using a computer code which solves the two-dimensional elliptic Navier-Stokes equations. The program computes the turbulent mixing and reaction of hydrogen fuel and air and allows the study of separated regions of the flow immediately preceding and following the injectors. The validity of the code is demonstrated in a cold flow helium injection study with a single injector. Results are presented that describe the flow field near opposing staged injectors over a range of parameters. Parameters that are varied include injector size, fuel split, and distance between injectors. Comparisons of the configurations are made to assess their mixing and potential flame-holding qualities.

Weidner, E. H.↗
NASA NTRS1990

Parametric study of an ODW scramaccelerator for hypersonic test facilities

A parametric study has been conducted for an oblique detonation-wave (ODW) 'scramaccelerator' suitable for projectile aerothermodynamics studies in real gas hypersonic test facilities. The results of the present analytical design evaluation indicate that an ODW scramaccelerator using conventional gaseous propellants can accelerate projectiles of 0.1 to 1000 kg masses to speeds in the 6-10 km/sec range. Potential applications for such an accelerator encompass a hypersonic ballistic test range, kinetic energy weapon accelerators, mass drivers to LEO, projectile terminal ballistics testing, projectile/target interaction studies, inertial welders, and shock compactors.

Humphrey, Joseph W.↗